Рассмотрена возможность автоматизации расчетов в области кондиционирования воздуха. Изучено программное обеспечение CFD-моделирования. Проведено несколько расчетов и анализ полученных результатов. Разработаны методические указания по работе в программе для внедрения ее в работу компании. / Possibility of automation of calculations in the field of air conditioning is considered. Studied CFD modeling software. Several calculations and analysis of the obtained results were carried out. Guidelines for working in the program have been developed for its implementation in the work of the company.

No description available.

Single-phase CFD calculations are already widely applied in nuclear industry for the thermal-hydraulic design optimization of fuel assemblies (FA). In contrast, two-phase CFD-applications are still in the state of development. The work presented in this thesis shows contributions towards the detailed two-phase modeling of boiling flows under swirl conditions in sub-channel geometries of pressurized water reactors (PWR) FAs, including a realistic description of the critical heat flux (CHF)-phenomena and identification of two-phase indicators characterizing CHF-phenomena. The numerical simulations were conducted with a 3-D CFD code (STAR CD) for various types of swirl generating components in FA. New insights regarding local void distribution in sub-channels under swirl conditions were obtained, which are relevant for CHF (“bubble pockets”). Furthermore, an enhanced wall partitioning model provides a more realistic description of the steep increase of the rod temperature due to CHF. Presented validation studies showed good agreement with the available experiments under PWR conditions for the radial void distributions at non-CHF conditions as well as for the CHF prediction. The results performed in this thesis show the incentives and chances of two-phase CFD applications for the development of thermal-hydraulically optimized PWR spacer grids with regard to heat transfer and improvement to the CHF behaviour. / Einphasige CFD Analysen stellen für typische thermohydraulische Fragestellungen aus dem Kernkraftwerksbereich bereits jetzt ein wichtiges Werkzeug für die Brennelement (BE)¬Auslegung dar. Die zweiphasige CFD-Modellierung befindet sich dagegen in der Entwicklungsphase. Die in dieser Dissertation präsentierten Arbeiten zeigen Fortschritte für die detaillierte zweiphasige Modellierung drallbehafteter Strömungen im Unterkanal eines BEs des Druckwasserreaktors (DWR) einschließlich der realistischen Beschreibung des kritischen Wärmestroms (CHF) sowie die Bestimmung zweiphasiger Indikatoren, welche das Auftreten von CHF-Phänomen beschreiben. Verschiedene drallerzeugende Komponenten im BE wurden mit dem 3-D CFD-Code STAR-CD modelliert. Es wurden neue Erkenntnisse zur lokalen Blasenverteilung in Unterkanälen unter Drallbedingungen gewonnen, die für CHF relevant sind (“bubble pockets”). Durch eine Modifikation des Wärmeübergangsmodells (heat partitioning model) wird der starke Anstieg der Stabtemperatur infolge CHF realistischer beschrieben. Die durchgeführten Validierungen zeigen eine gute Übereinstimmung mit verfügbaren Experimenten unter DWR-Bedingungen für die radialen Blasenverteilungen und für die Bestimmung von CHF. Die vorliegenden Ergebnisse dieser Dissertation verdeutlichen den Nutzen und die Möglichkeiten von zweiphasigen CFD-Anwendungen für die Entwicklung und die thermohydraulische Optimierung von DWR-Abstandshaltern bezüglich des Wärmeübergangs und der Verbesserung des CHF-Verhaltens. / Модели однофазовой среды в вычислительной гидродинамике (англ. CFD) являются уже сейчас важным инструментом для решения типичных термогидравлических задач в ядерной энергетике, например, при конструировании тепловыделяющих сборок (ТВС). Двухфазовое моделирование, в сравнении с однофазовым, находится на сегодняшний момент в стадии развития. Данная диссертация связана с совершенствованием двухфазовой модели в направлении улучшения детализации вихревого течения внутри ячейки ТВС в условиях работы двухконтурного ядерного реактора (тип PWR). Также в работе показана возможность более реалистичного описания феномена кризиса теплоотдачи и определения двухфазовых индикаторов, характеризующих критический тепловой поток (англ. CHF). Комплекс расчетов выполнен для различных интенсификаторов теплоотдачи, размещенных на дистанционирующих решетках TBC. Расчеты производились с помощью программного обеспечения STAR-CD, позволяющего моделировать трехмерные гидродинамические системы. Полученные новые данные о локальном распределении пузырьков в ячейках с вихревым течением дали важную информацию для идентификации критического теплового потока. Усовершенствование модели теплоотдачи на поверхности тепловыделяющего элемента (ТВЭЛ) позволило более реалистично описать резкое повышение температуры на поверхности ТВЭЛа при достижении критических условий. Полученные результаты численного моделирования для радиальных распределений пузырьков при нормальных условиях работы PWR и также для определения критического теплового потока показали хорошее совпадение с известными экспериментальными данными. Представленные в диссертации результаты показывают возможности применения двухфазовых CFD-расчётов для разработки и термогидравлической оптимизации дистанционирующих решеток с целью улучшения теплообмена и характеристик критического теплового потока в двухконтурном ядерном реакторе типа PWR.

Divertors are in-vessel, plasma-facing, components in magnetic-confinement fusion reactors. Their main function is to remove the fusion reaction ash (α-particles), unburned fuel, and eroded particles from the reactor, which adversely affect the quality of the plasma. A significant fraction (~15 %) of the total fusion thermal power is removed by the divertor coolant and must, therefore, be recovered at elevated temperature in order to enhance the overall thermal efficiency. Helium is the leading coolant because of its high thermal conductivity, material compatibility, and suitability as a working fluid for power conversion systems using a closed high temperature Brayton cycle. Peak surface heat fluxes on the order of 10 MW/m^2 are anticipated with surface temperatures in the region of 1,200°C to 1,500°C. Recently, several helium-cooled divertor designs have been proposed, including a modular T-tube design and a modular finger configuration with jet impingement cooling from perforated end caps. Design calculations performed using the FLUENT® CFD software package have shown that these designs can accommodate a peak heat load of 10 MW/m^2. Extremely high heat transfer coefficients (~50,000 W/(m^2 K)) were predicted by these calculations. Since these values of heat transfer coefficient are considered to be outside of the experience base for gas-cooled systems, an experimental investigation has been undertaken to validate the results of the numerical simulations. Attention has been focused on the thermal performance of the T-tube and the finger divertor designs. Experimental and numerical investigations have been performed to support both divertor geometries. Excellent agreement has been obtained between the experimental data and model predictions, thereby confirming the predicted performance of the leading helium-cooled divertor designs for near- and long-term magnetic fusion reactor designs. The results of this investigation provide confidence in the ability of state-of-the-art CFD codes to model gas-cooled high heat flux plasma-facing components such as divertors.

Computational fluid dynamics (CFD) modeling is possibly the best available technique in designing and predicting the performance of Stirling and pulse tube refrigerators (PTR). One of the limitations of CFD modeling of these systems, however, is that it requires closure relations for the micro porous materials housed within their regenerators and heat exchangers. Comprehensive prediction of fluid-solid interaction through this media can be obtained only by direct pore level simulation, a process which is time consuming and impractical for system level examination. Through the application of empirical correlations including the Darcy permeability and Forchheimer's inertial coefficient, the microscopic momentum equations governing fluid behavior within the porous structure can be recast as viable macroscopic governing equations. With these constitutive relationships, CFD can be an efficient and powerful tool for system modeling and optimization. The purpose of this study is to determine the hydrodynamic parameters of two mesh fillers relevant to miniature PTRs; stacked screens of 635 mesh stainless steel and 325 mesh phosphor-bronze wire cloth. Experimental setups were designed and fabricated to measure steady and oscillatory pressures and mass flow rates of the working fluid, research-grade helium. Hydrodynamic parameters for the two mesh fillers were determined for steady-state and steady periodic flow in both the axial and radial directions for a range of flow rates, operating frequencies and charge pressures. The effect of average pressure on the steady axial flow hydrodynamic parameters of other common PTR filler materials was also investigated. The determination of sample hydrodynamic parameters and their subsequent computational and experimental methodologies utilized are explained.

Cette étude concerne la compréhension des mécanismes de transfert de chaleur et le développement d’un système de stockage pour la valorisation de la chaleur fatale industrielle. L’utilisation de Matériaux à Changement de Phase (MCP) permet d’atteindre une densité énergétique élevée et de restituer la chaleur à température constante. Cependant, leur faible conductivité thermique impose d’améliorer les transferts thermiques, notamment par l’utilisation d’échangeurs à surface augmentée. Le but est de comprendre le comportement de tels échangeurs en régime transitoire au contact de MCP. Une étude expérimentale à basse température, où quatre échangeurs de type tube-calandre ont été testés avec différentes orientations (horizontale/verticale) et injections (haut/bas), a mis en évidence des phénomènes de transfert thermique importants, comme la convection naturelle à la charge et la contraction volumique à la décharge. Ces observations ont été validées par un modèle CFD tridimensionnel. Une méthode de comparaison des performances basée sur un calcul d’énergie par le biais d’un maillage expérimental est proposée et permet de sélectionner un échangeur selon les critères de densités énergétiques, de temps caractéristique et de coût. Trois MCP, envisagés pour l’application, ont alors été testés à température réelle (100-200 °C) au contact d’un échangeur tube inox à ailettes transverses en aluminium pour évaluer leur cyclabilité et comparer leur comportement. Le mélange de sels, H105 (Tfusion = 122 °C), n’est pas retenu pour l’application à cause de sa faible densité énergétique (≈ 56 kWh/m3) et sa plage de fusion trop étalée. L’acide sébacique (Tfusion = 132 °C) a un comportement répétable au cours des cycles et une densité énergétique plus élevée (≈ 66 kWh/m3). L’alcool de sucre, l’érythritol (Tfusion = 118 °C), présente de bonnes thermo-physiques (128 kWh/m3) mais la maîtrise de sa cristallisation est un point clé pour l’utiliser en tant que MCP. / This PhD thesis deals with the understanding of the heat transfer mechanisms and with the development of thermal energy storage system for the industrial waste heat recovery application. The use of Phase Change Materials (PCM) is attractive for its high storage density and its possibility to deliver heat at constant temperature. However, the PCM low thermal conductivity leads to develop heat transfer improvement methods, such as heat exchangers with increased heat transfer surface. The goal is to characterize the behavior of such heat exchangers An experimental study, where four several heat exchangers have been tested with different orientations (horizontal/vertical) and injection types (upward/downward), highlighted the impact of natural convection during the melting process and the volume contraction one during the solidification. These results have been validated through a 3D numerical model. A performance comparison method based on an energy calculation through an experimental mesh is proposed and enables to select a heat exchanger on criteria such as the storage density, the characteristic time and the cost. Three PCM, adapted to our application, have been tested at the intended temperature (100-200 °C) by integrating them into a storage system made of a stainless steel tube with aluminum circular fins. Their ability to resist to repeated cycles has been assessed and their behavior has been compared. The salts mixture, H105 (Tmelting = 122 °C), is not selected for the application because of it low storage density (≈ 56 kWh/m3) and its large melting area. The sebacic acid (Tmelting = 132 °C) has a repeatable behavior with cycles and a higher storage density (≈ 66 kWh/m3) and is appropriate as storage material. The sugar alcohol, erythritol (Tmelting = 118 °C), has good thermo-physical properties (128 kWh/m3) but the crystallization control is a key point to use it as a PCM.

This research is directed toward the investigation of a low temperature direct propane fuel cell (DPFC). Modeling included a parametric study of a direct propane fuel cell using computational fluid dynamics (CFD), specifically FreeFem++ software. Polarization curves predicted by the CFD model were used to understand fuel cell performance. The predictions obtained from the computational fluid dynamics mathematical model for the fuel cell were compared with experimental results. The computational work identified some critical parameters (exchange current density, pressure, temperature) for improving the overall performance of the fuel cell. The model predictions clearly highlighted the role of catalysts in significantly enhancing the overall performance of a DPFC. Experiments were performed using commercial Nafion-Pt based membrane electrode assemblies (MEAs) to obtain a basis for comparison. It is the first report in the literature that a Pt-Ru (Platinum-Ruthenium) MEA was used in the investigation of a DPFC. Also, it was the first study that fed liquid water continuously to a DPFC by using interdigitated flow field (IDFF) at the anode to humidify the dry propane feed gas. During the experiments oscillations were observed at very low current densities i.e. in nA/cm2, which is a rare case and not reported in the literature to date. This observation has raised serious concerns about the existence of absolute open-circuit cell potential difference for a DPFC. The cycling behaviour observed with DPFC indicated the presence of a continuous degradation-regeneration process of the catalyst surface near open-circuit potential. The experimental work further evaluated the performance of fuel cell by measurement of polarization curves.

Single-phase CFD calculations are already widely applied in nuclear industry for the thermal-hydraulic design optimization of fuel assemblies (FA). In contrast, two-phase CFD-applications are still in the state of development. The work presented in this thesis shows contributions towards the detailed two-phase modeling of boiling flows under swirl conditions in sub-channel geometries of pressurized water reactors (PWR) FAs, including a realistic description of the critical heat flux (CHF)-phenomena and identification of two-phase indicators characterizing CHF-phenomena. The numerical simulations were conducted with a 3-D CFD code (STAR CD) for various types of swirl generating components in FA. New insights regarding local void distribution in sub-channels under swirl conditions were obtained, which are relevant for CHF (“bubble pockets”). Furthermore, an enhanced wall partitioning model provides a more realistic description of the steep increase of the rod temperature due to CHF. Presented validation studies showed good agreement with the available experiments under PWR conditions for the radial void distributions at non-CHF conditions as well as for the CHF prediction. The results performed in this thesis show the incentives and chances of two-phase CFD applications for the development of thermal-hydraulically optimized PWR spacer grids with regard to heat transfer and improvement to the CHF behaviour. / Einphasige CFD Analysen stellen für typische thermohydraulische Fragestellungen aus dem Kernkraftwerksbereich bereits jetzt ein wichtiges Werkzeug für die Brennelement (BE)¬Auslegung dar. Die zweiphasige CFD-Modellierung befindet sich dagegen in der Entwicklungsphase. Die in dieser Dissertation präsentierten Arbeiten zeigen Fortschritte für die detaillierte zweiphasige Modellierung drallbehafteter Strömungen im Unterkanal eines BEs des Druckwasserreaktors (DWR) einschließlich der realistischen Beschreibung des kritischen Wärmestroms (CHF) sowie die Bestimmung zweiphasiger Indikatoren, welche das Auftreten von CHF-Phänomen beschreiben. Verschiedene drallerzeugende Komponenten im BE wurden mit dem 3-D CFD-Code STAR-CD modelliert. Es wurden neue Erkenntnisse zur lokalen Blasenverteilung in Unterkanälen unter Drallbedingungen gewonnen, die für CHF relevant sind (“bubble pockets”). Durch eine Modifikation des Wärmeübergangsmodells (heat partitioning model) wird der starke Anstieg der Stabtemperatur infolge CHF realistischer beschrieben. Die durchgeführten Validierungen zeigen eine gute Übereinstimmung mit verfügbaren Experimenten unter DWR-Bedingungen für die radialen Blasenverteilungen und für die Bestimmung von CHF. Die vorliegenden Ergebnisse dieser Dissertation verdeutlichen den Nutzen und die Möglichkeiten von zweiphasigen CFD-Anwendungen für die Entwicklung und die thermohydraulische Optimierung von DWR-Abstandshaltern bezüglich des Wärmeübergangs und der Verbesserung des CHF-Verhaltens. / Модели однофазовой среды в вычислительной гидродинамике (англ. CFD) являются уже сейчас важным инструментом для решения типичных термогидравлических задач в ядерной энергетике, например, при конструировании тепловыделяющих сборок (ТВС). Двухфазовое моделирование, в сравнении с однофазовым, находится на сегодняшний момент в стадии развития. Данная диссертация связана с совершенствованием двухфазовой модели в направлении улучшения детализации вихревого течения внутри ячейки ТВС в условиях работы двухконтурного ядерного реактора (тип PWR). Также в работе показана возможность более реалистичного описания феномена кризиса теплоотдачи и определения двухфазовых индикаторов, характеризующих критический тепловой поток (англ. CHF). Комплекс расчетов выполнен для различных интенсификаторов теплоотдачи, размещенных на дистанционирующих решетках TBC. Расчеты производились с помощью программного обеспечения STAR-CD, позволяющего моделировать трехмерные гидродинамические системы. Полученные новые данные о локальном распределении пузырьков в ячейках с вихревым течением дали важную информацию для идентификации критического теплового потока. Усовершенствование модели теплоотдачи на поверхности тепловыделяющего элемента (ТВЭЛ) позволило более реалистично описать резкое повышение температуры на поверхности ТВЭЛа при достижении критических условий. Полученные результаты численного моделирования для радиальных распределений пузырьков при нормальных условиях работы PWR и также для определения критического теплового потока показали хорошее совпадение с известными экспериментальными данными. Представленные в диссертации результаты показывают возможности применения двухфазовых CFD-расчётов для разработки и термогидравлической оптимизации дистанционирующих решеток с целью улучшения теплообмена и характеристик критического теплового потока в двухконтурном ядерном реакторе типа PWR.

Antarctic Wind Engineering deals with the effects of wind on the built environment. The assessment of wind induced forces, wind resource and wind driven snowdrifts are the main tasks for a wind engineer when participating on the design of an Antarctic building. While conventional Wind Engineering techniques are generally applicable to the Antarctic environment, there are some aspects that require further analysis due to the special characteristics of the Antarctic wind climate and its boundary layer meteorology. <p>The first issue in remote places like Antarctica is the lack of site wind measurements and meteorological information in general. In order to complement this shortage of information various meteorological databases have been surveyed. Global Reanalyses, produced by the European Met Office ECMWF, and RACMO/ANT mesoscale model simulations, produced by the Institute for Marine and Atmospheric Research of Utrecht University (IMAU), have been validated versus independent observations from a network of 115 automatic weather stations. The resolution of these models, of some tens of kilometers, is sufficient to characterize the wind climate in areas of smooth topography like the interior plateaus or the coastal ice shelves. In contrast, in escarpment and coastal areas, where the terrain gets rugged and katabatic winds are further intensified in confluence zones, the models lack resolution and underestimate the wind velocity. <p>The Antarctic atmospheric boundary layer (ABL) is characterized by the presence of strong katabatic winds that are generated by the presence of surface temperature inversions in sloping terrain. This inversion is persistent in Antarctica due to an almost continuous cooling by longwave radiation, especially during the winter night. As a result, the ABL is stably stratified most of the time and, only when the wind speed is high it becomes near neutrally stratified. This thesis also aims at making a critical review of the hypothesis underlying wind engineering models when extreme boundary layer situations are faced. It will be shown that the classical approach of assuming a neutral log-law in the surface layer can hold for studies of wind loading under strong winds but can be of limited use when detailed assessments are pursued. <p>The Antarctic landscape, mostly composed of very long fetches of ice covered terrain, makes it an optimum natural laboratory for the development of homogeneous boundary layers, which are a basic need for the formulation of ABL theories. Flux-profile measurements, made at Halley Research Station in the Brunt Ice Shelf by the British Antarctic Survery (BAS), have been used to analyze boundary layer similarity in view of formulating a one-dimensional ABL model. A 1D model of the neutral and stable boundary layer with a transport model for blowing snow has been implemented and verified versus test cases of the literature. A validation of quasi-stationary homogeneous profiles at different levels of stability confirms that such 1D models can be used to classify wind profiles to be used as boundary conditions for detailed 3D computational wind engineering studies. <p>A summary of the wind engineering activities carried out during the design of the Antarctic Research Station is provided as contextual reference and point of departure of this thesis. An elevated building on top of sloping terrain and connected to an under-snow garage constitutes a challenging environment for building design. Building aerodynamics and snowdrift management were tested in the von Karman Institute L1B wind tunnel for different building geometries and ridge integrations. Not only for safety and cost reduction but also for the integration of renewable energies, important benefits in the design of a building can be achieved if wind engineering is considered since the conceptual phase of the integrated building design process.<p> / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished

Das Elektronenstrahlschweißen im Vakuum hat sich als zuverlässiges Verfahren für die Herstellung schmaler und hochpräziser Schweißnähte beim Schweißen von TRIP-Stählen bewährt. Das Verständnis für die dabei auftretenden Mechanismen und wirkenden Kräfte stellt einen wichtigen Baustein für die Weiterentwicklung des Verfahrens dar. Um zur Erweiterung dieses Verständnisses beizutragen, wird auf Basis vorhandener Berechnungsmethoden in OpenFOAM ein numerisches Modell für das Elektronenstrahlschweißen entwickelt. Es ist in der Lage, die dafür relevanten Einflussfaktoren zu berücksichtigen. So werden die Wärmeübertragung im Feststoff und der Schmelze, alle Aggregatzustandsänderungen und die auf die Dynamik der Schmelze wirkenden Kräfte einbezogen. Das entwickelte Simulationsmodell ist in der Lage zu zeigen, dass außer der natürlichen Konvektion vor allem der beim Verdampfen der Schmelze entstehende Überdruck und die thermokapillare Konvektion an der Schmelzeoberfläche für hohe Strömungsgeschwindigkeiten verantwortlich sind. Darüber hinaus haben neben der Schmelzbaddynamik die thermophysikalischen Eigenschaften des Stahls einen starken Einfluss auf die Ausprägung der Schweißnaht. Vor allem die Wärmeleitfähigkeit verändert diese erheblich, was die Simulationen unter Berücksichtigung der Temperaturabhängigkeit verdeutlichen. Die in dieser Arbeit erreichten Erkenntnisse helfen, die beim Elektronenstrahlschweißen entstehenden Nahtgeometrien und die Gründe für hohe Strömungsgeschwindigkeiten im Schmelzbad besser einordnen und verstehen zu können. Darüber hinaus dient das entwickelte numerische Modell mit der Berücksichtigung aller relevanten Mechanismen als Grundlage für Weiterentwicklungen hinsichtlich vielerlei Anwendungen, beispielsweise für das Schweißen anderer Werkstoffe, zusätzliche Effekte wie dem Spiking oder anderen Elektronenstrahltechnologien wie dem Elektronenstrahlschmelzen im Bereich der additiven Fertigung.