Recently, Coherent Optical Orthogonal Frequency-division Multiplexing (CO-OFDM) has been considered as a promising technology for high-speed optical transmission due to its easiness of dispersion compensation, high optical spectral efficiency and superior scalability over the channel dispersion and data rate. In this thesis, we conduct analysis on the transceiver nonlinearity impact on a coherent optical Orthogonal Frequency-division Multiplexing (OFDM) system and the feasibility of transmitting up to 1 Tb/s per channel data rate over CO-OFDM WDM systems. / We investigate the optimum design for a CO-OFDM transmitter using an optical In-phase/Quadrature (I/Q) modulator and show by simulation that in contrast to the direct-detected system, the optimal modulator bias point for the coherent system is π, or the null point of the modulator. We also propose and demonstrate through simulation a transmitter side digital signal processing technique including digital clipping and digital pre-distortion to compensate the nonlinearity induced by the OFDM peak-to-average power ratio effect and Mach–Zehnder modulator (MZM). Furthermore, we conduct analysis on the study of nonlinearity and dynamic range for a CO-OFDM receiver induced by the imbalance between the two ports of a balanced receiver. The input power dynamic range and tolerance to the relative-intensity-noise (RIN) are analyzed for the coherent balanced-receiver. / We then explore the transmission performance for high speed wavelength-division multiplexing (WDM) CO-OFDM systems with up to 1Tb/s per channel data rate under the impact of fiber nonlinearity. We find that the optimum fiber launch power increases almost linearly with the increase of data rate. A 7 dB optimum launch power difference is observed between 107-Gb/s and 1.07-Tb/s CO-OFDM systems. We also investigate the dispersion compensation fiber impact and filter concatenation effect issues when upgrading the 10-Gb/s to the future 100-Gb/s CO-OFDM systems. We identify three contributions to the Q degradation for the inline dispersion compensated WDM systems. We show that due to the high spectral efficiency, 100-Gb/s CO-OFDM signals have very high tolerance to the filter narrowing effect, and are resilient to the group ripples from the filter concatenation effect.

No description available.

Orientadores: Aldário Chrestani Bordonalli, Júlio César Rodrigues Fernandes de Oliveira / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de Computação / Made available in DSpace on 2018-09-27T13:36:17Z (GMT). No. of bitstreams: 1 Carvalho_LuisHenriqueHeckerde_M.pdf: 8092940 bytes, checksum: da29699f8638d37de27fc0743c89a013 (MD5) Previous issue date: 2014 / Resumo: Uma das alternativas para os sistemas de transmissão óptica de próxima geração é o uso de múltiplos subcanais ópticos densamente multiplexados em frequência (supercanais) com alta eficiência espectral. Supercanais ópticos empregam o processamento paralelo de sinais para alcançar taxas de transmissão além dos limites da eletrônica. Atualmente, as técnicas CO-OFDM e Nyquist WDM são vistas como as principais para a implementação de supercanais ópticos. Neste trabalho, estudam-se abordagens para aumentar a capacidade de transmissão dos sistemas ópticos por meio da realização de supercanais. A implementação em laboratório, análise de desempenho e comparativo entre as técnicas CO-OFDM e Nyquist WDM são realizadas para sistemas operando a 400 Gb/s e 1 Tb/s por canal, com modulação DP-16QAM e eficiências espectrais que chegam a 6 b/s/Hz e acima. Os principais desafios e soluções para a implementação de sistemas de transmissão óptica de próxima geração baseados em supercanais são identificados / Abstract: One of the options for the next generation of optical transmission systems is the use of multiple optical subchannels densely multiplexed in frequency (superchannels) with high spectral efficiency. Optical superchannels employ parallel signal processing to achieve transmission rates beyond the limits of electronics. Currently, CO-OFDM and Nyquist WDM are seen as the main techniques to the implementation of optical superchannels. In this work, different ways to increase the capacity of the current optical systems by the realization of superchannels are studied. The experimental implementation, performance analysis, and comparison between CO-OFDM and Nyquist WDM techniques are performed for systems operating at 400 Gb/s and 1 Tb/s per-channel with DP-16QAM modulation and spectral efficiencies of 6 b/s/Hz and beyond. The main challenges and solutions for the implementation of next generation optical transmission systems based on superchannels are identified / Mestrado / Telecomunicações e Telemática / Mestre em Engenharia Elétrica

Fiber-optic networks are continually evolving to accommodate the ever increasing data rates demanded by modern applications and devices. The current state-of-the art systems are being deployed with 100 Gb/s rates per wavelength while maintaining the 50 GHz channel spacing established for 10 Gb/s dense wavelength division multiplexed (DWDM) systems. Phase modulation formats (in particular quadrature phase shift keying - QPSK) are necessary to meet the spectral efficiency (SE) requirements of the application. The main challenge for phase modulated optical systems is fiber nonlinearities, where changes in intensity of the combined optical signal result in changes to the fiber's refractive index. Limiting launch power is the primary means to avoid dramatic intensity fluctuations, a strategy which in turn limits the available signal-to-noise ratio (SNR) within the channel. Continuous phase modulation (CPM) is a format in which data is encoded in the phase, while the amplitude is constant throughout all transmission (even during transitions between symbols). With the goal of reducing the impact of nonlinearities, the purpose of this research was to identify a set of CPM signals best suited for high speed fiber-optic transmission, and quantify their performance against other formats. The secondary goal was to identify techniques appropriate for demodulation of high speed fiber-optic systems and implement them for simulation and experimental research. CPM encompasses a number of variable parameters that combine to form an infinite number of unique schemes, each of which is characterized by its own SE, minimum distance, and implementation complexity. A method for computing minimum distance of DWDM-filtered CPM formats is presented and utilized to narrow down to a range of candidate schemes. A novel transmitter design is presented for CPM signal generation, as well as a number of novel reception techniques to achieve proper demodulation of the CPM signal from the coherent optical receiver. Using these methods, the identified range of candidate schemes was compared in simulation to the conventional QPSK format, showing that some modest gain can be expected from CPM. Through these and other simulations, it is revealed that fiber nonlinearities depend on the aggregate sum of all wavelengths rather than the imposition of each separate carrier on its neighbors. Therefore the constant envelope of CPM does not directly impact the nonlinearities since multiple carriers will photonically interfere and result in intensity fluctuations regardless of modulation format. Additionally, dispersive effects in fiber decompose the underlying channels so that the intensity throughout propagation is nearly Gaussian distributed, regardless of format. The benefits gained from CPM are thus limited to schemes that attain a higher minimum distance than alternative formats (in the given channel passband), and for optically compensated links in which low dispersion is maintained throughout the fiber link.

Coherent optical data processing is recognised, for many applications, as a viable alternative to digital electronic signal processing; the case for using coherent optics is particularly strong when the data to be processed is two dimensional in nature. It has long been accpeted that, in order for coherent optical processing to achieve its full performance potential, two dimensional spatial light modulators - capable of operating in real time - are essential at both the object plane (where the data is input to the system) and the Fourier plane (where the operation carried out on the data is determined). Most previous research in the field of spatial modulators has concentrated on optically addressed devices for use in the object plane. This thesis describes a prototype liquid crystal over silicon spatial light modulator built to test the feasibility of using such devices in a coherent optical processor. Optically, the device operates as a binary amplitude modulator, consisting of a square array of 16x16 pixels, each of size 100x100 m^2 and located at 200m centres. The integrated circuit is designed for a 6m wafer fabrication process. Each pixel of the IC contains a static memory element (which stores a digital logic voltage corresponding to the optical state of that pixel) and provides a stable square wave voltage signal to drive the liquid crystal layer. The component parts of the spatial light modulator are tested individually: the liquid crystal, in test cells, for contrast and switching speed; the IC for electrical performance and optical (flatness) characteristics. The effect of pixellation on optical performance is investigated. The performance of live devices is demonstrated. The results indicate the feasibility of using such a device as a binary amplitude spatial light modulator.

With the technological shift towards big data, internet of things (IoT), 5G applications and cloud computing, the demand for high capacity networks is dramatically increasing. To avoid congestion and saturation, content and service providers are re-designing their network (backbone, metro and data-centers interconnects) connectivity using gridless optical line systems along with programmable coherent transponders. The latter are expected to transmit data at different data rates up to 400 Gb/s. In 2008, the first coherent receiver was commercially available [1]. By means of high-speed analog to digital converters and adaptive digital signal processing (DSP) algorithms, such revolution in modern optical communication was possible. That allowed a better spectral efficiency using higher order modulation formats and further signal reach by means of compensating both linear and nonlinear impairments. Another key development was leveraging light polarization-diversity, that permits to double the data rate at the expense of receiver complexity. To further increase the capacity of fiber links, gridless DWDM networks are being developed for deployment in the next few years. The key idea is to allow variable bandwidth signals to be allocated on optical links and by performing the appropriate network layer optimization improved throughput can be achieved. These innovations are driving new types of challenges for routing and assignment methods, as well, DSP algorithms such as clock recovery and compensation of fiber non-linearity. This thesis is organized as a collection of contributions and composed of five major parts. The first part, consisting of chapters 2 and 3. Chapter 4 deals with tracking of fast state of polarization transient, i.e. dynamic aspect of optical channels, in presence of polarization dependent loss (PDL) and filtering effects due to reconfigurable optical add-drop multiplexers (ROADMs). Chapters 5 and 6 study the impact of filtering effects, quasi-static effects in optical links and transponders, represented by ROADMs in fixed-grid and Silicon Photonics (SiPh) modulators in flexible-grid networks, respectively. Chapters 7, 8 and 9, are related to clock recovery in digital coherent receivers. They cover mitigation of jitter in gridless applications, improving jitter when deploying phase interpolators (PI) and jitter injection as a test-mean to evaluate performance.

Orientadores: Dalton Soares Arantes, Fabbryccio Akkazzha Chaves Machado Cardoso / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de Computação / Made available in DSpace on 2018-08-24T01:49:02Z (GMT). No. of bitstreams: 1 Garcia_FabioLumertz_D.pdf: 40460342 bytes, checksum: 576d63ee41c2ab7aa3312f22902103b5 (MD5) Previous issue date: 2013 / Resumo: Esta tese apresenta um novo método para recuperação de portadora e fase, sem o emprego de Phase-Locked Loops, com aplicação em um sistema óptico coerente com modulação 16-QAM, taxa de 112Gb/s e multiplexação por polarização. A estrutura desenvolvida viabiliza uma Operação de Alinhamento dos símbolos modulados em fase e quadratura da constelação QAM, possibilitando a estimação eficiente dos desvios de freqüência e fase. Um projeto especial de preâmbulo foi concebido para o uso desta estrutura, possibilitando uma comutação suave para o segmento de dados com o auxílio de um esquema denominado Conjugado Virtual. Esses conceitos possibilitam correção de desvios de freqüência superiores a 1,5 GHz e operação com faixas de ruído de fase da ordem de 3,5 MHz (' DELTA' v × TS = 2.5 × 10?4), quando operando na taxa de 14 GBaud e em ambientes bastante degradados. Resultados de simulação apontam que nesses cenários degradados a equalização não-fracionária não é capaz de realizar a inversão do canal óptico. Essa conclusão é particularmente ilustrada por uma imagem bidimensional relacionando as taxas de erro de bit (BERs) em função de pares de amostras. Finalmente, o sistema óptico foi emulado com o software VPI Photonics. / Abstract: This thesis presents a novel method for Carrier Phase Estimation (CPE), without Phase-Locked Loops, with application to a 112 Gb/s Dual-Polarization 16-QAM Coherent Optical System. The developed structure allows for an Alignment Operation that performs the alignment of the symbols of the QAM constellation, resulting in more efficient estimation of carrier frequency and phase. An especial preamble design was conceived for this structure, enabling a soft switching from preamble to data segment using an especial Virtual Conjugation scheme. These concepts enable frequency mismatch correction over to 1.5 GHz and operation with phase noise linewidth in the order of 3.5 MHz (' DELTA' v × TS = 2.5 × 10?4), when operating at the rate of 14 GBaud and highly degraded channel conditions. Simulation results show that, in these scenarios, baudrate equalization is not able to perform channel inversion. This conclusion is especially illustrated by a bidimensional image which depicts Bit Error Rates (BERs) as a function of pairs of samples. Finally, the optical system was emulated using VPI Photonics Simulation Software. / Doutorado / Telecomunicações e Telemática / Doutor em Engenharia Elétrica

[ES] Los sistemas de transmisión óptica no-coherente se emplean actualmente en las redes ópticas de corto alcance (< 80 km), como son las redes de ámbito metropolitano. La implementación más común en el estado del arte se basa en sistemas que emplean multiplexación por división en longitud de onda (WDM, wavelength division multiplexing) de cuatro longitudes de onda (¿) proporcionando un régimen binario de 100 Gbps (4¿×25 Gbps). En los últimos años, los sistemas de transmisión ópticos no-coherentes están evolucionando desde 100 Gbps a 400 Gbps (4¿×100 Gbps). Dado que este mercado comprende un gran número de sistemas, el coste es un parámetro importante que debe ser lo más bajo posible. El objetivo de esta tesis es investigar distintos aspectos del procesado de señal en general y, específicamente, investigar nuevas técnicas de procesado digital de señal (DSP, digital signal processing) que puedan ser utilizadas en sistemas de transmisión óptica no-coherentes empleando la modulación por amplitud de pulsos (PAM, pulse-amplitude modulation). Para que una técnica DSP sea interesante en el contexto de una red óptica WDM no-coherente, esta debe mitigar de manera efectiva al menos una de las tres limitaciones principales que afectan a estos sistemas: limitaciones de ancho de banda, limitaciones por dispersión cromática (CD), y el ruido. En esta tesis se proponen y examinan una serie de algoritmos cuyo su rendimiento es analizado mediante simulación y experimentalmente en laboratorio: - Feed-forward equalizer (FFE): este es el esquema de ecualización más común que se emplea principalmente en las transmisiones ópticas no-coherentes de alto régimen binario. Puede compensar grandes limitaciones en el ancho de banda. - Estimación de la secuencia de máxima verosimilitud (MLSE): el MLSE es un detector óptimo y, por lo tanto, proporciona las mejores prestaciones en detección cuando se abordan las limitaciones por CD y de ancho de banda. - Conformación geométrica de la constelación: en los esquemas de modulación de intensidad óptica multinivel, la distancia entre los niveles de amplitud puede ajustarse adecuadamente (de manera que no son equidistantes) a fin de aumentar la tolerancia de la señal frente al ruido. - Conformación probabilística: técnica diseñada específicamente para esquemas de modulación multinivel. Esta técnica ajusta la probabilidad de cada nivel de amplitud de modo que se incrementa la tolerancia al ruido óptico. - Señalización de respuesta parcial (PRS, partial signaling response): este es un enfoque basado en DSP donde una interferencia entre símbolos (ISI, inter-symbol interference) controlada es introducida intencionalmente de tal manera que la señal resultante requiere menos ancho de banda. La técnica PRS puede adaptarse para combatir también el efecto de CD. - Pre-énfasis digital (DPE, digital pre-emphasis): esta técnica consiste en aplicar el inverso de la función de transferencia del sistema a la señal en el transmisor, lo que reduce el impacto de las limitaciones de ancho de banda en el receptor. - Modulación con codificación Trellis (TCM, Trellis-coded modulation): esquema de modulación que combina elementos de corrección de errores (FEC, forward error correction) con técnicas de partición en conjuntos y modulación multidimensional para generar una señal más resistente al ruido. - Modulación multidimensional por partición en conjuntos: muy similar a TCM, pero sin ningún elemento FEC. Tiene menos ganancias que TCM en términos de tolerancia al ruido, pero no es tan sensible al ISI. Utilizando estas técnicas, esta tesis demuestra que es posible lograr una transmisión óptica con régimen binario de 100 Gbps/¿ empleando componentes de bajo coste. En esta tesis también demuestra regímenes binarios de más de 200 Gbps, lo que indica que la transmisión óptica no-coherente con modulación PAM puede ser una solución viable y eficiente en coste / [CAT] Actualment, s'utilitzen sistemes òptics no coherents en xarxes òptiques de curt abast ( < 80 km), com són les xarxes d'àmbit metropolità. La implementació més comuna que podem trobar en l'estat de l'art es correspon amb sistemes emplenant multiplexació per divisió en longitud d'ona (WDM, wavelength division multiplexing) de quatre longituds d'ona (¿) proporcionant un règim binari de 100 Gbps (4¿×25 Gbps). En els últims anys, els sistemes de transmissió òptica no-coherents han evolucionat des de 100 Gbps cap a 400 Gbps (100 Gbps/¿). Atès que el mercat de sistemes de curt abast compren un gran volum de dispositius òptics instal·lats, el cost unitari és molt important i ha de ser el més baix possible. L'objectiu d'aquesta tesi és analitzar aspectes del processament de senyal en general i, específicament, investigar noves tècniques de processament digital de senyal (DSP, digital signal processing) que puguen ser utilitzades en sistemes de transmissió òptica no-coherent que utilitzen la modulació per amplitud d'impulsos (PAM, pulse-amplitude modulation). Per tal que una tècnica DSP es considere interessant per a una xarxa òptica WDM no-coherent, aquesta ha de mitigar efectivament almenys una de les tres principals limitacions que afecten aquests sistemes: limitacions d'ample de banda, limitacions per dispersió cromàtica (CD), i el soroll. En aquesta tesi s'examinen una sèrie d'algoritmes, el seu rendiment s'analitza per simulació i experimentalment en laboratori: - Feed-forward equalizer (FFE): aquest és l'esquema d'equalització més comú i s'utilitza bàsicament en les transmissions òptiques no coherents d'alt règim binari. Pot compensar grans quantitats de limitacions d'ample de banda. - Estimació de la seqüència de probabilitat màxima (MLSE): el MLSE és un detector òptim i, per tant, proporciona el millor rendiment quan es tracta de limitacions d'ample de banda i de CD. - Conformació geomètrica de la constel·lació: en esquemes de modulació òptica d'intensitat multinivell es pot ajustar la distància entre els nivells d'amplitud (de manera que ja no són equidistants) per augmentar la tolerància del senyal al soroll. - Conformació probabilística: una tècnica dissenyada específicament per als esquemes de modulació multinivell; ajusta la probabilitat de cada nivell d'amplitud de manera que augmenta la tolerància al soroll òptic. - Senyalització de resposta parcial (PRS, partial signaling response): és un enfocament basat en DSP on la interferència entre símbols (ISI, inter-symbol interference) controlada s'introdueix intencionalment de manera que el senyal resultant requereix menys ample de banda. La tècnica PRS es pot adaptar per combatre els efectes del CD. - Pre-èmfasi digital (DPE, digital pre-emphasis): aquesta tècnica consisteix a aplicar la inversió de la funció de transferència del sistema a la senyal en el transmissor de manera que es redueix l'impacte de les limitacions d'ample de banda en la senyal en el receptor. - Modulació amb codificació Trellis (TCM, Trellis-coded modulation): esquema de modulació que combina els elements de correcció d'errors avançats (FEC, forward error correction) amb tècniques de partionament de conjunts i modulació multidimensional per generar un senyal més resistent al soroll. - Modulació multidimensional per partició en conjuntes: molt similar a TCM però sense elements FEC. Té guanys menors que TCM en termes de tolerància al soroll, però no és tan sensible a l'ISI. Mitjançant l'ús d'aquestes tècniques, aquesta tesi demostra que és possible aconseguir una transmissió òptica amb un règim binari de 100 Gbps/¿ utilitzant components de baix cost. Esta tesi també demostra règims binaris de més de 200 Gbps, el que indica que la tecnologia no-coherent amb modulació PAM és una solució viable i eficient en cost per a una nova generació de sistemes transceptors òptics WDM funcionant a 800 Gbps (4¿×200 G / [EN] Non-coherent optical transmission systems are currently employed in short-reach optical networks (reach shorter than 80 km), like metro networks. The most common implementation in the state-of-the-art is the four wavelength (¿) 100 Gbps (4¿×25 Gbps) wavelength division multiplexing (WDM) transceiver. In recent years non-coherent optical transmissions are evolving from 100 Gbps to 400 Gbps (4¿×100 Gbps). Since in the short-reach market the volume of optical devices being deployed is very large, the cost-per-unit of the devices is very important, and it should be as low as possible. The goal of this thesis is to investigate some general signal processing aspects and, specifically, digital signal processing (DSP) techniques required in non-coherent pulse-amplitude modulation (PAM) optical transmission, and also to investigate novel algorithms which could be applied to this application scenario. In order for a DSP technique to be considered an interesting solution for non-coherent WDM optical networks it has to effectively mitigate at least one of the three main impairments affecting such systems: bandwidth limitations, chromatic dispersion (CD) and noise (in optical or electrical domain). A series of algorithms are proposed and examined in this thesis, and their performance is analyzed by simulation and also experimentally in the laboratory: - Feed-forward equalization (FFE): this is the most common equalizer and it is basically employed in every high-speed non-coherent optical transmission. It can compensate high bandwidth limitations. - Maximum likelihood sequence estimation (MLSE): the MLSE is the optimum detector and thus provides the best performance when it comes to dealing with CD and bandwidth limitations. - Geometrical constellation shaping: in multilevel optical intensity modulation schemes the distance between amplitude levels can be adjusted (such that they are no longer equidistant) in order to increase the signal's tolerance to noise. - Probabilistic shaping: another technique designed specifically for multilevel modulation schemes; it adjusts the probability of each amplitude level such that the tolerance to optical noise is increased. - Partial response signaling (PRS): this is a DSP-based approach where a controlled inter-symbol interference (ISI) is intentionally introduced in such a way that the resulting signal requires less bandwidth. PRS can be customized to also mitigate CD impairment, effectively increasing transmission distances up to three times. - Digital pre-emphasis (DPE): this technique consists in applying the inverse of the transfer function of the system to the signal at the transmitter side which reduces the impact of bandwidth limitations on the signal at the receiver side. - Trellis-coded modulation (TCM): a modulation scheme that combines forward error correction (FEC) elements with set-partitioning techniques and multidimensional modulation to generate a signal that is more resistant to noise. - Multidimensional set-partitioned modulation: very similar with TCM but without any FEC elements. It has lower gains than TCM in terms of noise tolerance but is not so sensitive to ISI. By using the techniques enumerated above, this thesis demonstrates that is possible to achieve 100 Gbps/¿ optical transmission bitrate employing cost-effective components. Even more, bitrates higher than 200 Gbps are also demonstrated, indicating that non-coherent PAM is a viable cost-effective solution for next-generation 800 Gbps (4¿×200 Gbps) WDM transceivers. / Prodaniuc, C. (2019). Advanced Signal Processing for Pulse-Amplitude Modulation Optical Transmission Systems [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/117315 / TESIS

The increase in capacity demand along with the advancement in digital signal processing (DSP) have recently revived the interest in coherent optical communications and led to its commercialization. However, design and development of robust DSP algorithms for example for carrier phase recovery (CPR) becomes complex as we opt for high order modulation formats such as 16QAM and beyond. Further, electrical-domain dispersion compensation (EDC), while providing many advantages, makes the system more susceptible to laser frequency noise (FN). For instance, in coherent optical links with post-reception EDC, while the transmitter frequency noise causes only phase impairment, the local oscillator (LO) FN in these systems results in a noise enhancement in both amplitude and phase. This noise is commonly known as equalization enhanced phase noise (EEPN). It results in asymmetric requirements for transmitter laser and LO laser. Further, the system design in the presence of lasers with non-white frequency noise becomes increasingly challenging for increased capacity-distance product. The main contributions of this thesis are, firstly, an experimentally validated theory of coherent optical links with lasers having general non-white frequency noise spectrum and corresponding system/laser design criteria and mitigation technique. Secondly, low complexity and high phase noise tolerant CPR for high order modulation formats. The general theory propounded in this thesis elucidates the origin of the laser frequency noise induced noise enhancement in coherent optical links with different DSP configurations. The thesis establishes the existence of multiple frequency noise regimes and shows that each regime results in different set of impairments. The influence of the impairments due to some regimes can ideally be reduced by optimizing the corresponding mitigation algorithms, while other regimes cause irretrievable impairments. Experimentally validated theoretical boundaries of these regimes and corresponding criteria applicable to system/laser design are provided. Further, an EEPN mitigation method and its two possible implementations are proposed and discussed. The thesis also demonstrates an intrinsic limitation of the conventional Blind Phase Search (BPS) algorithm due to angular quantization and provides methods to overcome it. Finally, this thesis proposes and demonstrates single stage and multi-stage carrier phase recovery algorithms for compensation of phase impairments due to the two lasers for higher order circular and square modulations. The proposed methods outperform the state of art algorithms both in performance and in complexity. / <p>QC 20170516</p> / European project ICONE gr. #608099

[pt] Estuda-se a relação de complementaridade entre a visibilidade e a distinguibilidade espectral dos pacotes de onda fotônicos deslocados em frequência em um interferômetro de Hong-Ou-Mandel. Uma definição experimental de K, o parâmetro de distinguibilidade, é proposta e testada para a desigualdade de complementaridade K2 mais V2 é menor ou igual à 1 quando um parâmetro de visibilidade consistente é definido. Os resultados mostram que a distinguibilidade espectral é, de fato, complementar à visibilidade e que o aspecto quântico do fenômeno de interferência de dois fótons pode ser examinado empregando estados coerentes atenuados. / [en] The complementarity relation between the visibility and the spectral distinguishability of frequencydisplaced photonic wave-packets in a Hong- Ou-Mandel interferometer is studied. An experimental definition of K, the distinguishability parameter, is proposed and tested for the K2 + V2 is less than or equal to 1 complementarity inequality when a consistent visibility parameter is defined. The results show that the spectral distinguishability is, indeed, complementary to the visibility and that the quantum aspect of the two-photon interference phenomenon can be examined by employing weak-coherent states.