<p>Crystal structure, morphology and crystallization kinetics of melt-crystallized polypropylene and poly(propylene-stat-ethylene) fractions with 2.7 to 11.0 mol% of ethylene were studied by differential scanning calorimeter, wide- and small-angle X-ray scattering, polarized light microscopy, transmission electron microscopy and infrared spectroscopy. With increasing ethylene content the poly(propylene-stat-ethylene) fractions showed unchanged crystallinity, increased unit cell volume and constant crystal thickness in combination with a shortened helix length. This indicated that a fraction of ethylene defects were incorporated into the crystal structure. During the isothermal crystallization both α- and γ-crystals could be formed. The γ-crystal fraction increased with increasing ethylene content and increasing crystallization temperature. For samples with α- and γ-crystal contents, multimodal melting was observed and a noticeable γ- to α-crystal conversion was observed on slow heating. The spherulitic structure of the copolymers was coarser than that for the homopolymer.</p><p>The crystalline lamellae in copolymers exhibited profound curvature in contrast to the straighter cross-hatched α-crystals typical to the homopolymer. Area dependence of electrical breakdown strength was studied for thin polypropylene homopolymer films. The measurements were performed with an automatic measurement system equipped with a scanning electrode arm. Five different electrodes having areas between 0.045 cm2 and 9.3 cm2 were used and typically 40-80 breakdowns per sample and electrode area were collected. All measurements were performed on dry samples in air at room temperature. The data was analyzed statistically and the Weibull function parameters α and β, the first one related to 63% probability for the sample to break down and the second one to the width of the distribution were fitted to the obtained data. Different features concerning the measurement system and conditions, e.g. criteria for the automatic detection of the breakdowns, effect of electrode edge design, partial discharges, DC ramp speed and humidity were critically analyzed. It was concluded that the obtained α-parameter values were stable and repeatable over several years of time. The β-parameter values, however, varied ± 10-30%, more for the large than the small electrodes, and were also sensitive to the changes both in the sample itself and in the measurement conditions.</p><p>Breakdown strengths of over 50 capacitor grade polypropylene films were analyzed. The obtained α-parameter values were between 450 and 850 V/μm, depending on the film grade and electrode area. In addition to the high breakdown strengths, reflected by the obtained α-values, another, sparse distribution consisting of low breakdown strengths was revealed when the amount of measurement points was high enough. This means that more than one Weibull distribution could be needed to describe the breakdown strength behavior of a polypropylene film. Breakdown values showed decreasing area dependence with decreasing electrode area. Breakdown strengths for larger sample areas were predicted from the small area data by area- and Weibull extrapolation. The area extrapolation led to predicted α-values 50% higher than measured at 4 m² whereas the Weibull extrapolation showed an accuracy of ±15 % when predicted and measured values were compared.</p><p>Breakdown strengths were also extrapolated for film areas similar to those in impregnated power capacitors. It turned out that the power capacitors, tested at the factory, performed much better than predicted by the extrapolation. However, a few weak spots with very low breakdown values were also found. For the poly(ethyelene terephtalate) dielectric, which is not swelled by the impregnation liquid, the large area breakdown strength was predictable. This indicates that for polypropylene film processing and impregnation led, in addition to the improved large area breakdown performance, also to sparse weak spots with low breakdown probabilities. Different Weibull distributions were responsible for the breakdown strengths for the processed and impregnated polypropylene than for the dry film samples.</p>

The aim of this research was to study the effect of pre-treatment and modification processes on the properties of hemp cellulose fibre for biopolymer composites application. Hemp fibres have been modified by various extraction, swelling, chemical and enzymatic treatments. The morphology and mechanical properties of the modified fibres have been measured. Biopolymer composites have been prepared using the modified fibres and matrices of cellulose acetate butyrate and cellulose solutions derived from hemp. The first fibre treatment employed was acetone extraction and mercerization. A low pressure acrylonitrile grafting initiated by azo-bis-isobutylonitrile was performed using alkali treated fibre. The AN grafted fibres had no transformation of crystalline structure as observed after mercerization. The mechanical properties performed by a single fibre test method were strongly influenced by the cellulose structure, lateral index of crystallinity, and fraction of grafting. Bioscouring of hemp using pectate lyase (EC 4.2.2.2), Scourzyme L, was performed. Greater enzyme concentration and a longer treatment improved the removal of the low methoxy pectin component. Removal of pectate caused no crystalline transformation in the fibres, except for a slight decline in the X-ray crystalline order index. Smooth surfaces and separated fibres were evidence of successful treatment. The shortening of fibre by grinding and ball-milling was introduced to achieve a desired fibre size. An increase in the milling duration gradual ly destroyed the crystalline structure of the cellulose fibres. An increase in solvent polarity, solvent-fibre ratio, agitation speed and drying rate resulted in the rearrangement of the ball-milled cellulose crystalline structure to a greater order. The thermal degradation behaviour of hemp fibres was investigated by using TGA. The greater activation energy of treated hemp fibre compared with untreated fibre represented an increase in purity and improvement of structural order. The all hemp cellulose composites were prepared by an introduction of fibres into 12% cellulose N-methyl-morpholine N-oxide (NMMO) solution and water-ethanol regeneration. A broadening of the scattering of the main crystalline plane, (002) and a depression of the maximum degradation temperature of the fibres were observed. These revealed a structural change in the fibres arising from the preparation. The mechanical properties of composites depended on size, surface area, crystallinity and the structural swelling of the fibres. Composites of cellulose acetate butyrate (CAB) and modified hemp fibres were prepared. Composites containing pectate lyase enzyme treated fibres showed better mechanical property improvement than untreated and alkali treated fibres respectively.

Abstract This thesis correlates rheological data into a non-linear blown film model that describes the stress and cooling-induced morphological transformations in the axial and flow profiles of the blown films. This will help to improve the physical and mechanical properties of the films in a cost effective way, which will in turn be of great benefit to the food and packaging industries. In this research, experimental and numerical studies of a blown film extrusion were carried out using two different low-density polyethylenes (LDPEs). In the experiment, the key parameters measured and analysed were molecular, rheological and crystalline properties of the LDPEs. In the numerical study, blown film simulation was carried out to determine the bubble characteristics and freeze line height (FLH). A new rheological constitutive equation was developed by combining the Hookean model with the well known Phan-Thien and Tanner (PTT) model to permit a more accurate viscoelastic behaviour of the material. For experimental verification of the simulation results, resins were processed in a blown film extrusion pilot plant using identical die temperatures and cooling rates as used in the simulation study. Molecular characteristics of both LDPEs were compared in terms of their processing benefit in the film blowing process. Based on the experimental investigation, it was found that molecular weight and its distribution, degree of long chain branching and cooling rate play an important role on melt rheology, molecular orientation, blown film processability, film crystallinity and film properties. Effect of short chain branching was found insignificant for both LDPEs. Statistical analysis was carried out using MINITAB-14 software with a confidence level of 95% to determine the effect of process variables (such as die temperature and cooling rate) on the film properties. Film properties of the LDPEs were found to vary with their molecular properties and the process variables used. Blown film model performance based on the newly established PTT-Hookean model was compared with that based on the Kelvin model. Justification of the use of PTT-Hookean model is also reported here using two different material properties. From the simulation study, it has been found that predictions of the blown film characteristics conformed very well to the experimental data of this research and previous studies using different materials and different die geometries. Long chain branching has been found as the most prominent molecular parameter for both LDPEs affecting melt rheology and hence the processability. Die temperature and cooling rate have been observed to provide similar effect on the tear strength and shrinkage properties of blown film for both LDPEs. In comparison to the Kelvin model, the PTT-Hookean model is better suited for the modelling of the film blowing process. It has also been demonstrated in this study that the PTT-Hookean model conformed well to the experimental data near the freeze line height and is suitable for materials of lower melt elasticity and relaxation time.

<p>Cellulose powders from various sources were manufactured and characterized to investigate the influence of their crystallinity index, surface area, and pore volume on sorption phenomena and the relevant pharmaceutical functionality. The influence of the cellulose crystallinity index on moisture sorption was important at low and intermediate relative humidities. At high relative humidities, properties such as surface area and pore volume took precedence in governing the moisture sorption process.</p><p>The theory of physical adsorption of gases onto fractal surfaces was useful for understanding the distribution of water in cellulose and the inner nanoscale structure of cellulose particles. It was found that, as a consequence of swelling, moisture induces a fractal nanopore network in cellulose powders that have a low or intermediate degree of crystallinity. On the other hand, no swelling occurs in highly crystalline cellulose powders and moisture sorption is restricted to the walls of the open pores.</p><p>No correlation was found between the cellulose crystallinity index and the incorporation and release of nicotine in cellulose mixtures. By loading nicotine in highly porous matrices of the Cladophora sp. algae cellulose, higher stability against oxidative degradation, higher loading capacity, and more steady release into an air-stream was achieved than when commercially available microcrystalline cellulose was loaded.</p><p>It was also shown that, by manipulating the structure of cellulose, the undesired hydrolysis of acetylsalicylic acid in mixtures with cellulose can be avoided. It was suggested that a broad hysteresis loop between the moisture adsorption and desorption curves of isotherms at low relative humidities could be indicative of an improved compatibility between acetylsalicylic acid and cellulose.</p><p>In all, this thesis demonstrates how the pharmaceutical functionality of microcrystalline cellulose can be improved via engineering of the structure of native cellulose powders.</p>

<p>In this thesis, factors important in tableting operations and for tablet properties have been studied and characterised by different spectroscopic techniques as well as by some more conventionally used particle characterisation techniques. The spectroscopic techniques solid-state NMR, FT-IR and NIR spectroscopy, proved to be valuable tools in the estimation of particle and tablet properties, offering both specificity and sensitivity in the measurements. Because of the large amount of information obtained in a spectrum, multivariate data analysis was in some cases used in the processing of the spectral data. Correlations between the solid state structure measured by spectroscopy and the particle and tablet properties could be obtained including useful prediction models.</p><p>The surface area obtained using different principles has in this thesis been shown to reflect different properties and tableting behaviour of a collection of pharmaceutical materials. The particle shape and the external surface area of the powders measured by permeametry, were found to be important factors for the tensile strength of tablets made of hydroxypropyl methylcellulose. Furthermore, the external surface area could be used to access dominating interparticulate bonding mechanisms in compacts of different materials by normalising the tablet tensile strength for the tablet surface area. It was also shown that for materials prone to develop solid bridges, the actual surface area participating in the bonding was more important than the average interparticulate distance. </p><p>When studying the properties of microcrystalline cellulose and cellulose powder from the alga <i>Cladophora</i> sp., the cellulose fibril surface area estimated by solid-state NMR resulted in better correlations to the tableting behaviour and to tablet disintegration than the external permeametric surface area did. It was suggested that the difference in fibril surface area of the two celluloses was the primary factor responsible for properties like the crystallinity and the disintegration of the tablets.</p>

<p>In this thesis, regioregularpoly( 3-hexylthiophene) (rr-P3HT) polymer was used as a light absorption and electron donating material, while the C60 fullerene and its derivative [6,6]-phenyl C61-butyric acid methyl ester (PCBM) were used as electron acceptor materials. The effect of solvent to control the degree of mixing of the polymer and fullerene components, as well as the domain size and charge transport properties of the blends were investigated in detail using P3HT:C60 films. The photo-physical, structural and electrical transport properties of the polymer blends were carried out according to their ratios. A distinctive photoluminescence (PL) quenching effect was observed indicating a photo-induced electron transfer. In this thesis, the effect of solvents on the crystallization and interchain interaction of P3HT and C60 fullerene films were studied using XRD, UV-vis, PL, Raman and FTIR spectroscopy. The polymer blends formed with non-aromatic solvents exhibited an improved crystallinity and polymer morphology than that formed with aromatic solvents. An improved ordering was demonstrated in the polymer films spin coated from non-aromatic solvents. This indicates that the limited solubility of rr P3HT in a marginal solvent such as non-aromatic solvents can offer a strategy to obtain highly ordered crystal structures and lead directly to optimal morphologies on the films.</p>

In this thesis, factors important in tableting operations and for tablet properties have been studied and characterised by different spectroscopic techniques as well as by some more conventionally used particle characterisation techniques. The spectroscopic techniques solid-state NMR, FT-IR and NIR spectroscopy, proved to be valuable tools in the estimation of particle and tablet properties, offering both specificity and sensitivity in the measurements. Because of the large amount of information obtained in a spectrum, multivariate data analysis was in some cases used in the processing of the spectral data. Correlations between the solid state structure measured by spectroscopy and the particle and tablet properties could be obtained including useful prediction models. The surface area obtained using different principles has in this thesis been shown to reflect different properties and tableting behaviour of a collection of pharmaceutical materials. The particle shape and the external surface area of the powders measured by permeametry, were found to be important factors for the tensile strength of tablets made of hydroxypropyl methylcellulose. Furthermore, the external surface area could be used to access dominating interparticulate bonding mechanisms in compacts of different materials by normalising the tablet tensile strength for the tablet surface area. It was also shown that for materials prone to develop solid bridges, the actual surface area participating in the bonding was more important than the average interparticulate distance. When studying the properties of microcrystalline cellulose and cellulose powder from the alga Cladophora sp., the cellulose fibril surface area estimated by solid-state NMR resulted in better correlations to the tableting behaviour and to tablet disintegration than the external permeametric surface area did. It was suggested that the difference in fibril surface area of the two celluloses was the primary factor responsible for properties like the crystallinity and the disintegration of the tablets.

Cellulose powders from various sources were manufactured and characterized to investigate the influence of their crystallinity index, surface area, and pore volume on sorption phenomena and the relevant pharmaceutical functionality. The influence of the cellulose crystallinity index on moisture sorption was important at low and intermediate relative humidities. At high relative humidities, properties such as surface area and pore volume took precedence in governing the moisture sorption process. The theory of physical adsorption of gases onto fractal surfaces was useful for understanding the distribution of water in cellulose and the inner nanoscale structure of cellulose particles. It was found that, as a consequence of swelling, moisture induces a fractal nanopore network in cellulose powders that have a low or intermediate degree of crystallinity. On the other hand, no swelling occurs in highly crystalline cellulose powders and moisture sorption is restricted to the walls of the open pores. No correlation was found between the cellulose crystallinity index and the incorporation and release of nicotine in cellulose mixtures. By loading nicotine in highly porous matrices of the Cladophora sp. algae cellulose, higher stability against oxidative degradation, higher loading capacity, and more steady release into an air-stream was achieved than when commercially available microcrystalline cellulose was loaded. It was also shown that, by manipulating the structure of cellulose, the undesired hydrolysis of acetylsalicylic acid in mixtures with cellulose can be avoided. It was suggested that a broad hysteresis loop between the moisture adsorption and desorption curves of isotherms at low relative humidities could be indicative of an improved compatibility between acetylsalicylic acid and cellulose. In all, this thesis demonstrates how the pharmaceutical functionality of microcrystalline cellulose can be improved via engineering of the structure of native cellulose powders.

Crystal structure, morphology and crystallization kinetics of melt-crystallized polypropylene and poly(propylene-stat-ethylene) fractions with 2.7 to 11.0 mol% of ethylene were studied by differential scanning calorimeter, wide- and small-angle X-ray scattering, polarized light microscopy, transmission electron microscopy and infrared spectroscopy. With increasing ethylene content the poly(propylene-stat-ethylene) fractions showed unchanged crystallinity, increased unit cell volume and constant crystal thickness in combination with a shortened helix length. This indicated that a fraction of ethylene defects were incorporated into the crystal structure. During the isothermal crystallization both α- and γ-crystals could be formed. The γ-crystal fraction increased with increasing ethylene content and increasing crystallization temperature. For samples with α- and γ-crystal contents, multimodal melting was observed and a noticeable γ- to α-crystal conversion was observed on slow heating. The spherulitic structure of the copolymers was coarser than that for the homopolymer. The crystalline lamellae in copolymers exhibited profound curvature in contrast to the straighter cross-hatched α-crystals typical to the homopolymer. Area dependence of electrical breakdown strength was studied for thin polypropylene homopolymer films. The measurements were performed with an automatic measurement system equipped with a scanning electrode arm. Five different electrodes having areas between 0.045 cm2 and 9.3 cm2 were used and typically 40-80 breakdowns per sample and electrode area were collected. All measurements were performed on dry samples in air at room temperature. The data was analyzed statistically and the Weibull function parameters α and β, the first one related to 63% probability for the sample to break down and the second one to the width of the distribution were fitted to the obtained data. Different features concerning the measurement system and conditions, e.g. criteria for the automatic detection of the breakdowns, effect of electrode edge design, partial discharges, DC ramp speed and humidity were critically analyzed. It was concluded that the obtained α-parameter values were stable and repeatable over several years of time. The β-parameter values, however, varied ± 10-30%, more for the large than the small electrodes, and were also sensitive to the changes both in the sample itself and in the measurement conditions. Breakdown strengths of over 50 capacitor grade polypropylene films were analyzed. The obtained α-parameter values were between 450 and 850 V/μm, depending on the film grade and electrode area. In addition to the high breakdown strengths, reflected by the obtained α-values, another, sparse distribution consisting of low breakdown strengths was revealed when the amount of measurement points was high enough. This means that more than one Weibull distribution could be needed to describe the breakdown strength behavior of a polypropylene film. Breakdown values showed decreasing area dependence with decreasing electrode area. Breakdown strengths for larger sample areas were predicted from the small area data by area- and Weibull extrapolation. The area extrapolation led to predicted α-values 50% higher than measured at 4 m2 whereas the Weibull extrapolation showed an accuracy of ±15 % when predicted and measured values were compared. Breakdown strengths were also extrapolated for film areas similar to those in impregnated power capacitors. It turned out that the power capacitors, tested at the factory, performed much better than predicted by the extrapolation. However, a few weak spots with very low breakdown values were also found. For the poly(ethyelene terephtalate) dielectric, which is not swelled by the impregnation liquid, the large area breakdown strength was predictable. This indicates that for polypropylene film processing and impregnation led, in addition to the improved large area breakdown performance, also to sparse weak spots with low breakdown probabilities. Different Weibull distributions were responsible for the breakdown strengths for the processed and impregnated polypropylene than for the dry film samples. / QC 20101027

Zinc xanthates polymerize propylene oxide into high polymer (PPO) with coordination mechanism. In order to identify structure and stereoisomerisms of this polymer, PPO was subjected to thermal and column fractionation. Obtained fractions were characterized by end-group analysis, cryoscopy, viscometry, IR and 13C-NMR spectroscopy, melting temperature. PPO is composed of a high molecular weight, stereoregular, crystallizable polymer (K-polymer) with low molecular weight (=500 g/mol) D-polymer. Presence of double bonds and hydroxyl terminals was interpreted as the product of an anionic mechanism. K-Polymers can be thermally fractionated on the basis of their melting temperature (Tm) rather than molecular weight (Mwt). It&amp / #8217 / s found that higher Tm fractions have lower Mwt, but they precipitate at higher temperatures than higher Mwt but lower Tm fractions. In column fractionation, K-polymers were deposited on glass beads from isooctane solution in a narrow temperature interval. Then the precipitated samples were split into a number of fractions by using again isooctane but at a higher temperature than the precipitation temperature by increasing residence time from 5 minutes to several hours. It&amp / #8217 / s found that rate of solubility is not controlled by molecular weight, but controlled by percentage crystallinity and Tm. Highest Tm polymers, with relatively higher Mwt showed faster rate of solution than that of lower Tm, lower Mwt but higher percent crystalline fractions. This discrepancy was accounted by suggesting a stereo-block structure where tactic blocks are bound each other with non-crystallizable atactic blocks. The mechanism of polymerization was also discussed in some detail.