none

In the present study / the effects of the powder metallurgical parameters such as the mixing method, compaction pressure, initial tungsten (W) particle size, composition, sintering temperature and sintering time on the sintering behavior of selected high density W-Ni-Cu alloys were investigated. The alloys were produced through conventional powder metallurgy route of mixing, cold compaction and sintering. The total solute (Ni-Cu) content in the produced alloys was kept constant at 10 wt%, while the copper concentration of the solutes was varied from 2.5 wt% to 10 wt%. Mainly liquid phase sintering method was applied in the production of the alloys. The results of the study were based on the density measurements, microstructural characterizations including optical and scanning electron microscopy and mechanical characterizations including hardness measurements. The results showed that the nature of the mixing method applied in the preparation of the powder mixtures has a considerable effect on the final sintered state of W-Ni-Cu alloys. Within the experimental limits of the study, the compaction v pressure and initial W particle size did not seem to affect the densification behavior. It was found that the sintering behavior of W-Ni-Cu alloys investigated in this study was essentially dominated by the Ni content in the alloy and the sintering temperature. A high degree of densification was observed in these alloys with an increase in the Ni content and sintering temperature which was suggested to be due to an increase in the solubility and diffusivity of W in the binder matrix phase with an increase in these parameters, leading to an increase in the overall sintering kinetics. Based on the results obtained in the present study, a model explaining the kinetics of the diffusional processes governing the densification and coarsening behavior of W-Ni-Cu alloys was proposed.

The world&rsquo / s being alerted to the global warming danger and the depletion of fossil fuel resources, has increased the importance of the clean and renewable hydrogen energy. Bioethanol has high potential to be used as a resource of hydrogen since it is a non-petroleum feedstock and it is able to produce hydrogen rich mixture by steam reforming reactions. Discovery of mesoporous MCM-41 type high surface area silicate-structured materials with narrow pore size distributions (20-100 &Aring / ) and high surface areas (up to 1500 m2/g) opened a new avenue in catalysis research. Catalytic activity of such mesoporous materials are enhanced by the incorporation of active metals or metal oxides into their structure. Nickel and copper are among the most active metals to be used in steam reforming of ethanol to produce hydrogen. In this study, copper and nickel incorporated MCM-41 type catalytic materials were tested in the steam reforming of ethanol. Two Ni-MCM-41 samples having different Ni/Si ratios were prepared by high temperature direct synthesis method and two Cu-MCM-41 samples having same Cu/Si ratios were synthesized by two different methods namely, high temperature direct synthesis method and impregnation method. The synthesized materials characterized by XRD, EDS, SEM, N2 physisorption and TPR techniques. XRD results showed that Ni-MCM-41 and Cu-MCM-41 catalysts had typical MCM-41 structure. The d100 and lattice parameter values of Ni-HT (I) (Ni-MCM-41 sample having 0.036 Ni/Si atomic ratio) was obtained as 3.96 and 4.57 nm., respectively. In addition Ni-HT (I) was found to have a surface area of 860.5 m2/g and 2.7 nm pore diameter. The d100 and lattice parameter values for a typical Cu-MCM-41 prepared by impregnation method having Cu/Si atomic ratio of 0.19 were obtained as 3.6 and 4.2 nm., respectively. This sample also has a 631 m2/g surface area and 2.5 nm pore diameter. Steam reforming of ethanol was investigated in the vapor phase by using Ni-MCM-41 and Cu-MCM-41 catalysts between 300&deg / C and 550&deg / C. Results proved that Ni incorporated MCM-41 type catalytic materials were highly active in hydrogen production by steam reforming of ethanol and actualized almost complete ethanol conversion for Ni-MCM-41 having Ni/Si atomic ratio of 0.15 over 500&deg / C . The side products obtained during reforming are methane and formaldehyde. Although the Cu-MCM-41 samples were not as active as Ni-MCM-41, it was observed that Cu-MCM-41 catalyst synthesized by the impregnation method showed an ethanol conversion of 0.83. However, the main product was ethylene with the copper incorporated catalysts. Effects of space time, the operating conditions (reaction temperature), metal/Si ratio of the catalyst and the preparation method on the product distributions were also investigated and best reaction conditions were searched.

The study of catalytic oxidation on the removal of NO was investigated over the Cu-catalysts . The Cu-catalysts , including Cu/TiO2 , Cu/Al2O3 and Cu/SiO2 , were prepared by impregnation method . Alougth NO2 , the product of this reaction , has higher toxicity than NO , but it might be removed completely by absorption with H2O or alkalinal solution for its high solubility . The experiments can be divided into three parts , i.e. , the screen of test catalysts , the effect of operating factors on the conversion of NO and the kinetic model . In the first part , the activity of test catalysts , which were prepared by mixing three various sources of Cu-ions¡]i.e., Cu(NO3)2 , Cu(CH3COO)2 , and CuSO4¡^with three different types of support¡]i.e., TiO2 , Al2O3 , and SiO2¡^, and were compared in form of conversion on NO to find the best catalyst . The results show that the mixture Cu(NO3)2 / TiO2 has the good performance on the conversion of NO , and also has more wider operating in range of temperature . In order to find the optimal loading of Cu on Cu(NO3)2 / TiO2 , additional test of various dosage over the catalysts was conduct in series . It is found that 8wt.% of Cu loading on Cu(NO3)2 / TiO2 is the most economic dosage . Therefore , we select this type of Cu oxide as the best catalyst in the following work . In the second part , the effect of NO inlet concentration , space velocity and humidity on the conversion of NO were performed . The results show that the conversion of NO decreases with the increasing of [NO]in when [NO]in is larger than 1000ppm¡Fthe conversion of NO is not changed with [NO]in when [NO]in is lower than 1000ppm . The better space velocity is 15000hr-1 , i.e.,the empty bed residence time is 0.24 second . The reaction on NO conversion would be restrained by higher humidity contenting in inlet gas stream , but the effect of inhibition on NO conversion is not significant . Finally , the kinetics of the oxidation of NO over 8wt.% Cu(NO3)2 / TiO2 was obtained by integral method .It is found that the oxidations of NO can be described by first order reversible reaction and the observed activation energy are 15.8 kcal/mole¡]forward reaction¡^and 25.9 kcal/mole¡]backward reaction¡^, respectively . By comparing the conversion of predicted NO with the experimentals , we can find the suitable operation conditions in application of the kinetic model : the inlet concentration of NO in a range of 300-1000ppm , the empty-bed residence time ranging from 0.12-0.48 second , and the absolute humidity ranging from 4854 to 42475ppm .

This study utilized Cu-catalysts to catalyze a NO reduction reaction using CH4 as a reductant. Due to CH4 being a weak reductant and is easily affected by O2 concentration, we undertook a series experiments with O2 concentration and promoters, so that we could better understand their influence. The experiment conditions were as follows : reaction temperature between 150¢J- 800¢J¡Fa catalysts weight of 0.5 g¡F total gas flow rate of 1000 ml/min¡Frelative humidity at 0.9 %¡Fan O2 concentration between 0 - 6%¡Fand CH4 concentration between 1000 - 10000 ppm. First, we sorted out the best metal carriers and calcining temperature, from this we decide to use £^-Al2O3 as a carrier with a calcining temperature under 500¢Jto produce our catalysts. During the O2 concentration experiment, when the inflow O2 concentration was below 1% (including 0% O2), Cu-catalysts reduce NO above 550¢J.The conversion reached a rate of 95 % at a temperature of 750¢J¡Fwhen the oxygen concentration was between 3% and 6% O2, catalysts reacted within 300 - 500¢J with NO converting to NO2¡Fat a concentration between 1.5% and 2% O2, NOx underwent reduction at 750¢J,and NOx conversion raised from 0 % to above 90%. Therefore in analyzing the experiment results, it shows that NOx will reduce violently when the O2 concentration is below 0.7% and while using CH4 as a reductant. This result was also apparent in O2 concentrations between 1.5 % and 2%. In the experiments of M/O ratio (the ratio of CH4 and O2 inflow), we found M/O ratio was not a deciding factor within the reaction mechanics, furthermore the limiting factor of O2 concentration decreases under 0.7%¡Fin addition it was also found that adding large amounts of CH4 could quicken the reduction process. Lastly, a mass balance was performed, which had a result over 70 %. In the experiments where Y¡BLa¡BSr¡BCo were added as promoters to the Cu-catalysts, we found that Cu-La/£^-Al2O3¡BCu-Sr/£^-Al2O3 and Cu-Co/£^-Al2O3 can accelerate O2 depletion. Henceforth, it is possible to deduce promoters will be a useful method in solving O2 limiting. In the comparison of metals loading methods, we found no difference in activity using separate-impregnation and co-impregnation methods, whereas in the BET and SEM co-impregnation experiments, there was a larger surface-area and dispersion.

ABSRACT This study was to investigate the removal efficiency and kinetics in oxidation of ammonia solutions (NH3-N) in ranging from 400 mg/L to 1000 mg/L by adding Cu/La/Ce catalyst in process of Wet Air Oxidation (denoted by WAO). All experiments were conducted in semi-batch and continuous reactors in series. The major parameters included temperature, pressure, concentration and pH. In the semi-batch type of WAO experiments, the major parameters were performed at the following conditions: an initial concentration NH3-N of 400 mg/L, temperatures ranging from 423 K to 503 K, a total pressure of 4.0 Mpa, and a pH of 12.0. A removal efficiency of 32.7%was obtained in WAO process at 503 K for180 min, but it could be significantly promote to 95.1% after adding a catalyst of molar ratio 7:2:1.The kinetics of WAO with this catalyst in oxidation of NH3-N solutions, using a test of half-life, was developed nearly to a zero order. The reaction constants were 10.12 KJ/mol, 9.12 KJ/mol, and 6.57 KJ/mol at 503 K, 473 K and 423 K. In the continuous type of WAO experiments, the major parameters were performed at the following conditions: an initial concentration NH3-N of 400 mg/L, a temperature of 503 K, a total pressure of 2.0 Mpa, a pH of 12.0 and a liquid space velocity of 4.5 hr-1 (averagelyresidence time 14 min) . A removal efficiency of NH3-N of 6.5 % only was achieved in WAO process for a space velocity of 4.5 hr-1 (averagely residence time 14 min) , but after adding a catalyst of molar ratio 7:2:1 it increased to 72.3 % for a same residence time and a better efficiency of above 91 % was found for 1.5 hr-1 (averagely residence time 40 min) . For increasing the initial concentration of NH3-N into 600 mg/L, 800 mg/L, and 1000 mg/L the removal efficiency of NH3-N decreased with 85 %,75 % and 69 % for 1.5 hr-1 . Thus, the initial concentration of NH3-N in influent inhibits the removal efficiency in the oxidation process. The higher initial concentration the lower removal efficiency.

Ultrasonic slurry sampling electrothermal vaporization dynamic reaction cellTM inductively coupled plasma mass spectrometry (USS-ETV-DRC-ICP-MS) has been applied to determine Cr, Cu, Cd, Hg and Pb in several rice samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Ascorbic acid was used as the modifier to enhance the ion signals. The background ions at the chromium masses were reduced in intensity significantly by using 0.4 ml min-1 NH3 as reaction cell gas in the dynamic reaction cell (DRC) while a q value of 0.6 was used. Since the sensitivities of Cr, Cu, Cd, Hg and Pb in rice flour slurry and aqueous solution were quite different, standard addition and isotope dilution methods were used for the determination of Cr, Cu, Cd, Hg and Pb in these rice samples. This method has been applied to the determination of Cr, Cu, Cd, Hg and Pb in NIST SRM 1568a rice flour reference material and two rice samples purchased from the market. The analysis results of the reference material agreed with the certified values. The results for the rice samples for which no reference values were available were also found to be in good agreement between isotope dilution method and standard addition method. The method detection limits estimated from standard addition curves were about 0.44, 1.7, 0.4, 0.53 and 0.69 ng g-1 for Cr, Cu, Cd, Hg and Pb, respectively, in original rice flour.Ultrasonic slurry sampling electrothermal vaporization dynamic reaction cellTM inductively coupled plasma mass spectrometry (USS-ETV-DRC-ICP-MS) has been applied to the determination of Cr, Cd and Pb in several plastic samples. The influences of instrument operating conditions and slurry preparation on the ion signals were investigated. NH4NO3 was used as the modifier to enhance the ion signals. The background ions at the chromium masses were reduced in intensity significantly by using NH3 as reaction cell gas in the DRC. Standard addition method and isotope dilution method were used for the determination of Cr, Cd and Pb in these plastic samples. This method was applied to the determination of Cr, Cd and Pb in two polystyrene and a polyvinyl chloride samples. The analysis results were found to be in good agreement between isotope dilution method and standard addition method. Furthermore, we digested these samples and analyzed the digested sample solutions by ultrasonic nebulization DRC ICP-MS. The analysis results were close to the isotope dilution and standard addition results. The precision between sample replicates was better than 3% with USS-ETV-DRC-ICP-MS method. The method detection limits estimated from standard addition curves were about 6.2-9.2, 1.1-1.6 and 8.4-11 ng g-1 for Cr, Cd and Pb, respectively, in original plastic samples.

In this work, the steady-state performance of zeolite-based (Cu-ZSM-5) and vanadium-based honeycomb monolith catalysts was investigated in the selective catalytic reduction process (SCR) for NO removal using NH3. The aim was to delineate the effect of various parameters including pretreatment of the catalyst sample with H2, NH3-to-NO ratio, inlet oxygen concentration, and space velocity. The concentrations of the species (e.g. NO, NH3, and others) were determined using a Fourier Transform Infrared (FTIR) spectrometer. The temperature was varied from ambient (25 C) to 500 C. The investigation showed that all of the above parameters (except pre-treatment with H2) significantly affected the peak NO reduction, the temperature at which peak NO reduction occurred, and residual ammonia left at higher temperatures (also known as 'NH3 slip'). Depending upon the particular values of the parameters, a peak NO reduction of around 90% was obtained for both the catalysts. However, an accompanied generation of N2O and NO2 species was observed as well, being much higher for the vanadium-based catalyst than for the Cu-ZSM-5 catalyst. For both catalysts, the peak NO reduction decreased with an increase in space velocity, and did not change significantly with an increase in oxygen concentration. The temperatures at which peak NO reduction and complete NH3 removal occurred increased with an increase in space velocity but decreased with an increase in oxygen concentration. The presence of more ammonia at the inlet (i.e. higher NH3-to-NO ratio) improved the peak NO reduction but simultaneously resulted in an increase in residual ammonia. Pretreatment of the catalyst sample with H2 (performed only for the Cu-ZSM-5 catalyst) did not produce any perceivable difference in any of the results for the conditions of these experiments.

Advancements in the semiconductor industry require new materials with improved performance. With the introduction of copper as the interconnect material for integrated circuits, efficient diffusion barriers are required to prevent the diffusion of copper into silicon, which is primarily through grain boundaries. This dissertation reports the processing of high quality stoichiometric thin films of TiN, TaN and HfN, and studies their Cu diffusion barrier properties. Epitaxial metastable cubic TaN (B1-NaCl) thin films were grown on Si(001) using an ultra-thin TiN (B1-NaCl) seed layer which was as thin as 1 nm. The TiN/TaN stacks were deposited by Pulsed Laser Deposition (PLD), with the TiN thickness systematically reduced from 15 to 1 nm. Microstructural studies included X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution TEM (HRTEM). Preliminary Cu diffusion experiments showed that the TiN seed layer thickness had little or no obvious effect on the overall microstructure and the diffusion barrier properties of the TaN/TiN stacks. Epitaxial and highly textured cubic HfN (B1-NaCl) thin films (~100 nm) were deposited on MgO(001) and Si(001) using PLD. Low resistivities (~40 mu omega-cm) were measured with a four point probe (FPP). Microstructural characterizations included XRD, TEM, and HRTEM. Preliminary Cu diffusion tests demonstrated good diffusion barrier properties, suggesting that HfN is a promising candidate for Cu diffusion barriers. Cubic HfN (B1-NaCl) thin films were grown epitaxially on Si(001) substrates by using a TiN (B1-NaCl) buffer layer as thin as ~10 nm. The HfN/TiN stacks were deposited by PLD with an overall thickness less than 60 nm. Detailed microstructural characterizations included XRD, TEM, and HRTEM. The electrical resistivity measured by FPP was as low as 70 mu omega-cm. Preliminary copper diffusion tests showed good diffusion barrier properties with a diffusion depth of 2~3 nm after vacuum annealing at 500 degrees C for 30 minutes. Additional samples with Cu deposited on top of the cubic HfN/TiN/Si(001) were vacuum annealed at 500 degrees C, 600 degrees C and 650 degrees C for 30 minutes. The diffusivity of copper in the epitaxial stack was investigated using HRTEM. The measured diffusion depths, 2 Dt , were 3, 4 and 5 nm at 500 degrees C, 600 degrees C and 650 degrees C respectively. Finally, the diffusivity of Cu into epitaxial HfN was determined to be D=D0 exp(-Q/kT)cm2s-1 with D0=2.3x10-14cm2s-1 and Q=0.52eV.

In the organometallic chemistry, the imido complexes are an interesting species because it of their rich reactivity. Imido has two forms, where M=N-R form is nucleophilic and M¡ÝN-R form is elctrophilic. The thermo- or photochemical- decomposition of metal azido complexes is known to result in the formation of the corresponding metal nitride(M¡ÝN) or imido complexes. These reactions are oxidative cleavage type. As far as we know, imido species have not been generated on metal surfaces; therefore, we attempt to use the azidotrimethylsilane((CH3)3Si-N3 ; TMSN3) as precursors to produce imido species(TMSN=Cu) by N2 extrusion mechanism on Cu(111). The process was explored by a combination of temperature-programmed desorption (TPD), reflection absorption infrared spectroscopy (RAIRS), and X-ray photoemission spectroscopy (XPS) techniques. In addition, density functional theory (DFT) calculations were conducted to obtain the optimized geometries for the various surface intermediates. The computed IR spectra facilitated the vibrational mode assignments. TPD spectra show that TMSN=Cu was hydrogenated to the TMSNH2 amine product around 520 K. We propose that the hydrogen source is adsorbed methyl groups, invoking the cleavage of the Si-C bond. TMSCH2N3 molecule was also investigated. In this case, N2 and H2 molecules were found to desorb around 260 K and 320K. A novel TMSC¡ÝN product was observed around 280K. We suggest it is a result of the metathesis reaction from ethylidyne (TMSC¡ÝCu) and nitride(N¡ÝCu) species. The TMSC¡ÝCu species are produced by double £\-hydride elimination of TMSCH2-Cu groups. The N¡ÝCu may be generated by the thermaldecomposition of copper azide(N=N=N-Cu). RAIRS reveal that there are three kinds of azido vibrations,where the higher frequency is assigned to the N=N=N-Cu species. This product is verified by the TPD of adsorbed TMSC¡ÝN molecule. Intriguingly, the thermal chemistry of TMSC¡ÝN molecule indicates that the isomeric molecule TMSN¡ÝC could be formed around 210 K, evidenced by a notable change in the RAIRS. The higher frequency £hC¡ÝN of TMSC¡ÝN transforms into a lower frequency £hC¡ÝN for TMSN¡ÝC. The coverage-dependent studies of RAIRS and XPS performed at 160 K surface temperature show that the isomerization may be intermolecular. The back-£k bonded TMSN¡ÝC molecule is desorbed around 410 K. XPS and RAIRS at 800 K show that isocyanide could polymerize to polyisocyanide, with an imine structure, and the characteristic C¡ÝN stretching mode disappeared.