<p> This study reports on karren forms on limestone dip slopes, which were recently exposed by deforestation on the Quatsino Formation and observable relationships of the karren features of a specific sl~pe are represented as a detailed map. Also, many relationships of gravitomorphic runnel characteristics are analyzed for significance. Runnel types being considered are Hortonian, decantation and composite forms. Solution runnel width, depth and width/depth ratio are studied in association with length. These relationships determine whether the runnel types conform to a theoretical model. Typical aeas·ares of the karren in this area were also recorded. Composite forms are the most abundant because Hortonian and decantation runnels amalgamate beyond about 3m to form composites. All the runnel types, excluding the decanters, illustrate the perfect minimum friction open-channel cross-section. </p> / Thesis / Bachelor of Arts (BA)

Implementation of solar power by photovoltaic modules in cold climates, such as northern Sweden, implies several challenges. Ice and snow coverage not only leads to reduction in energy production due to shading, but it also puts equipment at risk from additional weight. The goal of this thesis was to formulate a passive ice shedding coating for photovoltaics that could handle the demands of both high optical transmittance and durability. In addition, the coating should be environmentally friendly and low cost. For that purpose, a state-of-the-art, superhydrophobic sol-gel silica-based coating was selected with the focus on optimizing its transparency, wettability, and durability. Different concentrations of binder, tetraethyl orthosilicate (TEOS), and catalyst (HCl) in the sol were explored, as well as post-treatment temperatures and sol aging, Hydrophobization was done by self-assembly of a silane and plasma polymerization of a siloxane. The coatings were characterized by UV-Vis spectroscopy, contact angle measurements, Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), tape peel strength, freeze-thaw cycling, ice adhesion force and a field test. Superhydrophobic, anti-reflective coatings with high transmittance (88.5±1.9%) were achieved, with some of them retaining their superhydrophobic properties after 15 freeze-thaw cycles between room temperature and -20°C. The main findings were that the amount of TEOS in the sol has the largest influence on transmittance and strength, with more TEOS leading to less transparent but stronger coatings, and that calcination of the coatings greatly improves their durability.

Third-generation advanced high-strength steels (3G AHSS) are being developed to assist in vehicle light weighting so that fuel efficiency may be improved without sacrificing passenger safety. 3G-AHSS have received significant interest from the automotive industry as a critical candidate for their unique combination of high strength and ductility. However, due to selective oxidation of the principal alloying elements such as Mn, Si, Al, and Cr at the steel surface during the annealing stage prior to immersion in the galvanizing Zn(Al, Fe) bath, the process of continuous hot-dip galvanizing of these steel is challenging. This thesis determined the influence of annealing process parameters such as oxygen partial pressure and annealing time, on the selective oxidation and reactive wetting of an Fe-0.15C-5.56Mn-1.17Si-1Al (wt%) prototype 3G AHSS during intercritical annealing as well as continuous galvanizing. Simulated annealing and galvanizing were conducted on the prototype Fe-0.15C-5.56Mn-0117Si-1Al (wt%) 3G steel; Intercritical annealing heat treatments were carried out at 690˚C in a N2-5 vol pct H2 process atmosphere under dew points of 223 K (–50 °C), 243 (–30 °C) and 268 K (–5 °C). MnO was the major oxide formed at the outmost layer of the external oxides on all annealed samples. The experimental parameters, on the other hand, had a substantial impact on the morphology, distribution, thickness, and surface oxide coverage. The greatest Mn surface concentration as well as maximum surface oxide coverage and thickness was obtained by annealing the panels under the 223 K (–50 °C) and 243 (–30 °C) dp process atmospheres. The oxides formed under these process atmospheres largely comprised coarse, compact, and continuous film nodules. In contrast, MnO nodules formed under the 268 K (–5 °C) dewpoint process, exhibited wider spacing between finer and thinner nodules, which was consistent with the internal oxidation mode, while under 223 K (–50 °C) dp process atmosphere, generally external oxidation took place. Poor reactive wetting was obtained for the panels annealed under the 223 K (–50 °C) dp process atmosphere for both the 60 s and 120 s holding times as well as the 243 K (–30 °C) dp process atmosphere for 120 s. This was attributed to the formation of a thick, compact oxide layer on the steel surface, which acted as a barrier between the substrate and Zn bath, preventing Fe dissolution from the substrate surface for the formation of the desired Fe2Al5Znx interfacial layer. However, a well-developed interfacial Fe-Al intermetallic layer was formed under the 268 K (–5 °C) and 243 (–30 °C) dp process atmospheres for intercritical annealing times of 60 s, which is indicative of a good reactive wetting since the thinner and nodule-like oxides on the steel surface after annealing encourage the reactive wetting. External oxides morphology plays a dominant role in facilitating the contact between Zn-alloy bath and the substrate via different mechanisms such as aluminothermic reduction which occurred for the sample annealed under the 268 K (–5 °C) dp process atmosphere. / Thesis / Master of Applied Science (MASc)

Polymer coatings are thin films of polymer deposited on different substrates for various applications. Such surface coatings can serve a functional purpose (adhesives, photographic films), protective purpose (anticorrosion), or decorative purpose (paint). Additionally, their composite coatings containing ceramic, or metal particles are often used to enhance durability, functionality, or aesthetics. Electrophoretic deposition (EPD) and dip coating are two promising methods for the fabrication of polymer and composite coatings due to the ease of fabrication, low cost, and high-volume production. EPD involves the electrophoresis of charged particles and their deposition on the electrode surface, which requires the colloidal particles to be charged in a stable suspension as a precursor solution for deposition. Many polymers cannot be deposited by EPD directly because of their charge neutrality and poor dispersion. Therefore, it is critical to develop efficient charging dispersants to modify electrically neutral polymers for their EPD. The approach was inspired by the strong solubilization power of bile acids in the human body. Two types of bile salts, cholic acid sodium salt and sodium chenodeoxycholate, and three types of biosurfactants, carbenoxolone sodium salt, glycyrrhizic acid, and 18β-glycyrrhetinic acid, which share similar structures with bile salts, were discovered for charging, dispersion, and EPD of different materials. The electrically neutral polymers (PTFE and PVDF), chemically inert materials (diamond, nanodiamond, graphene, carbon dots, carbon nanotubes and Zr-doped hydrotalcite (MHT)), and their composites can be well dispersed in suspension and deposited using these bio-surfactants as dispersants. It was found that the unique chemical structures of these biomolecules play vital roles in the surface modification and EPD of different materials. Moreover, the deposited polymer (PVDF, PTFE) and composite (PTFE-MHT) coatings can provide outstanding corrosion protection for stainless steel. The biomimetic and versatile strategy opens a way for the deposition of other electrically neutral materials through EPD. These findings also provide a promising strategy for selecting new dispersants for EPD. The deposition of high molecular weight (MW) polymers such as poly(ethyl methacrylate) (PEMA) at high concentrations in non-toxic solvents continues to be a challenge for dip coating. In this work, we firstly proposed using water-isopropanol as a co-solvent to dissolve high MW PEMA at high concentrations. It was found that water molecules can solvate carbonyl groups of PEMA and facilitate their dissolution. This method avoided the usage of toxic solvents and a long-time heating procedure for their removal. Moreover, it allows the fabrication of high-quality PEMA and composite coatings containing different flame retardant materials (FRMs), including double hydroxide LiAl2(OH)7.2H2O (LiAlDH), huntite, halloysite and hydrotalcite, through the dip coating method. A novel solid state synthesis method was proposed to fabricate LiAlDH, which is promising for the fabrication of other advanced DHs. Such composite coatings combined advanced properties of PEMA and functional properties of FRMs, such as corrosion inhibition and FR properties. / Thesis / Doctor of Engineering (DEng) / Polymer and composite coatings have been utilized for a wide range of applications due to their barrier properties, scratch and abrasion resistance, chemical resistance, and biocompatibility. Various techniques have been developed to fabricate polymer and composite coatings, such as electrophoretic deposition (EPD) and the dip coating method. However, limitations remain. EPD unitizes an electrical field to drive charged particles in a suspension toward conductive substrates to achieve film deposition. This process requires a stable suspension with charged particles, therefore, the electroneutral polymers present difficulties in their EPD. In addition, dissolving high molecular weight polymers at high concentrations in a non-toxic solvent is currently challenging, which is vital to utilize dip coating technique. The objective of this work was to develop advanced charging dispersants for EPD of electroneutral polymers and non-toxic solvents for dip coating of high molecular weight polymers. New biomimetic and versatile approaches have been developed for EPD of different electrically neutral polymers, chemically inert materials, and their composite coatings. A non-toxic co-solvent was proposed to dissolve high molecular weight polymer at high concentration for dip coating of the polymer and its composite coatings containing flame retardant materials. The results presented in this work showed the formation of high-quality films with multifunctionality and paved new strategies for further developments.

No description available.

No description available.

No description available.

<p> Intercritically annealed steels, such as dual-phase steels, have found widespread use in automotive structural components due to their high strength and ductility. Elements such as Mn, Al and Si, added to improve the mechanical properties are selectively oxidized during heat treatment and limit the ability of the alloy to be reactively wet during continuous hot-dip galvanizing. Subsequently, a limit has been placed on the amount of alloy which can be used if the steel is to be subsequently galvanized. The specifics of this limit have not been explored in detail, nor has the mechanism of decreased wettability been well demonstrated in the literature other than to say that the galvanizing reaction is limited by oxides on the surface.</p> <p> Using a force balance, it is shown that the presence of MnO on the surface of steels greatly reduces the wettability with a typical galvanizing bath (Zn-0.2wt%Al, Fe-saturated, 460°C). Furthermore, it was determined that this is caused by the additional and rate-limiting step of aluminothermic reduction of the oxide layer with the bath Al, required for subsequent inhibition layer formation. By using a low pO2 during annealing, the wettability was improved by reducing the thickness of the MnO layer when compared to intermediate and industrially common values of pO2. Using a high pO2 also resulted in improved wettability since the internal oxide which was formed did not reduce the wettability since it was not exposed to the bath alloy.</p> <p> Improvements in hardenability were also explored via dilatometry showing that the formation of bainite is delayed with increasing Mn content, as well as a decrease in transformation temperatures from γ during cooling (i.e. Ms and Bs). At ~5wt% Mn, only the the transformation to αM could be observed. This opens the door to higher strength, galvanized steels - as well as possibly galvanized martensitic steels.</p> / Thesis / Master of Applied Science (MASc)

<p> Aluminum is usually added to the zinc bath to form an Fe-Al interfacial layer which retards the formation of a series of Fe-Zn intermetallic compounds during the hot-dip galvanizing process. However, experimentally exploring the inhibition layer formation and obtaining useful experimental data to understand the mechanisms is quite challenging due to short times involved in this process. In this study, a galvanizing simulator was used to perform dipping times as short as O.ls and rapid spot cooling techniques have been applied to stop the reaction between the molten zinc coating and steel substrate as quickly as possible. In addition, the actual reaction time has been precisely calculated through the logged sample time and temperature during the hot-dipping process. The kinetics and formation mechanism of the inhibition layer was characterized using SEM, ICP and EBSD based on the total reaction time. For bath containing 0.2wt% dissolved AI, the results show that FeA13 nucleates and grows during the initial stage of the inhibition layer formation and then Fe2Als forms by a diffusive transformation. The evolution of the interfacial layer formed in a zinc bath with 0.13wt% dissolved AI, including Fe-Aland Fe-Zn intermetallic compounds, was a result of competing reactions. In the initial period, the Fe-Al reaction dominated due to high thermodynamic driving forces. After the zinc concentration reached a critical composition in the substrate grain boundaries, formation of Fe-Zn intermetallic compounds was kinetically favoured. Fe-Zn intermetallic compounds formed due to zinc diffusing to the substrate via short circuit paths and continuously grew by consuming Fe-Al interfacial layer after samples exited the zinc bath due to the limited Al supply. A mathematical model to describe the formation kinetics as a function of temperature for the 0.2wt% Al zinc bath was proposed. It indicated that the development of microstructure of the interfacial layer had significant influence on the effective diffusion coefficient and growth of this layer. However, the model underestimates the AI uptake by the interfacial layer, particularly at higher temperatures. This is thought to be due to the effect of the larger number of triple junctions in the inhibition layer leading to an underestimation of the effective diffusivity. </p> / Thesis / Master of Science (MSc)

Third generation advanced high-strength steels (3G-AHSS) have received significant interest from leading auto steel industries and OEMs as candidate materials for reduced mass Body In White (BIW) components due to their unique combination of high specific strength and ductility. However, the continuous hot-dip galvanizing of these steels is challenging due to selective oxidation of the main alloying elements such as Mn, Si, Al and Cr at the steel surface during the annealing step prior to immersion in the galvanizing Zn(Al, Fe) bath, as extensive coverage of the substrate surface by these oxides is detrimental to reactive wetting, good coating adhesion and integrity. Simulated galvanizing treatments were conducted on two prototype Fe-0.1C-6Mn-2Si (wt pct) 3G steels; one as the reference steel and the other with 0.05 wt pct Sn added to the composition. The combined effects of annealing temperature, time, process atmosphere oxygen partial pressure and 0.05 wt pct Sn addition on the selective oxidation of the steel substrates were determined. Subsequently, the reactive wetting of the steels with respect to the pre-immersion surface structures of the samples annealed for 120 s was examined. Annealing heat treatments were carried out at 800˚C and 690˚C in a N2-5 vol pct H2 process atmosphere under three dew points of –50˚C, –30˚C and +5˚C, covering process atmosphere oxygen partial pressures within the range of 1.20  10-27 atm to 1.29  10-20 atm. MnO was present at the outmost layer of the external oxides on all samples after annealing. However, the morphology, distribution, thickness and surface coverage were significantly affected by the experimental variables. Annealing the reference steel under the low dew point process atmospheres, i.e. –50˚C and –30˚C, resulted in the highest Mn surface concentration as well as maximum surface oxide coverage and thickness. The oxides formed under these process atmospheres generally comprised coarse, compact and continuous film forming nodules, whereas the surface morphologies and distributions obtained under the +5˚C dew point process atmosphere, which was consistent with the internal oxidation mode, exhibited wider spacing between finer and thinner MnO nodules. The grain boundary internal oxide networks had a multi layer structure with SiO2 and MnSiO3 at the oxide cores and shells, respectively. Significant morphological changes were obtained as a result of Sn addition. The continuous film-like external MnO nodules were modified to a fine and discrete globular morphology, with less surface coverage by the oxides and reduced external oxide thickness. Both the external and internal oxidations followed parabolic growth kinetics, where the depth of the internal oxidation zone decreased with Sn addition and decreasing oxygen partial pressure. Poor reactive wetting was observed for the reference steel substrates that were annealed for 120 s under the –50˚C and –30˚C dew point process atmospheres at 800˚C and under the –50˚C dew point atmosphere at 690˚C, such that no integral metallic coating was formed after the 4 s immersion in the Zn(Al, Fe) bath. By contrast, excellent coating quality was obtained for the Sn-added steels when the –30˚C and +5˚C dew point process atmospheres were employed when annealing at 690˚C. The remainder of the experimental conditions demonstrated good reactive wetting with intermediate coating quality. For the two reference steels annealed at 800˚C under the –50˚C and –30˚C dew point process atmospheres, poor reactive wetting was due to full coverage of the surface by 116 nm and 121 nm thick and continuous MnO films. In the case of the 690˚C  –50˚C reference steel with the external layer thickness of only 35 nm, however, poor wetting was attributed to substantial coverage of the surface by continuous, film-like oxides. In both cases, exposure of the underlying substrate to the bath alloy and an intimate contact between the substrate Fe and the bath dissolved Al could not take place and the formation of the Fe2Al5Znx interfacial layer was hidered. For the processing conditions that satisfactory reactive wetting was obtained despite the pre-immersion selective oxidation of the surfaces, several reactive wetting mechanisms were determined. For the samples with a sufficiently thin external MnO layer, good reactive wetting was attributed to partial reduction of MnO by the bath dissolved Al, as well as bridging of the Mn sub-oxides by the Zn coating or Fe2Al5Znx interfacial intermetallics. Partial or full formation of the Fe2Al5Znx interfacial layer was observed in the successfully galvanized substrates with Fe-Al crystals formed between, underneath and also on top of the reduced oxides. Furthermore, for cases with widely-spaced, fine oxide nodules, it was found that the liquid bath alloy was able to infiltrate the external oxide/substrate interface, resulting in surface oxide lift-off and enhanced coating adhesion. It was globally concluded that the thin, discrete and fine globular morphology of external MnO, resultant of annealing the steel substrates with 0.05 wt pct Sn addition under the process atmosphere oxygen partial pressures consistent with internal oxidation, allowed for an enhanced reactive wetting by the Zn(Al, Fe) galvanizing bath which was manifested by increased amount of Al uptake and population of the Fe2Al5Znx intermetallics at the coating/steel interface. / Thesis / Doctor of Science (PhD)