Difficulties in characterizing the dynamic behavior of wood structures have hindered investigations into their performance under dynamic loading. Because of this, wood structures are treated unfavorably in seismic design codes, even though past damage assessment surveys after seismic events indicated generally satisfactory performance. To allow investigations into their performance and safety under dynamic loading, the energy dissipation mechanisms of wood joints and structural systems must be known and the hysteretic behavior modeled properly. This thesis presents a general hysteresis model for wood joints and structural systems, based on a modification of the Bouc-Wen-Baber-Noori (BWBN) model. The hysteretic constitutive law, based on the endochronic theory of plasticity and characterized by a single mathematical form, produces a versatile, smoothly varying hysteresis that models previously observed behavior of wood joints and structural systems, namely, (1) nonlinear, inelastic behavior, (2) stiffness degradation, (3) strength degradation, (4) pinching, and (5) memory. The constitutive law takes into account the experimentally observed dependence of wood joints' response to their past history (Le., the input and response at earlier times, or memory). Practical guidelines to estimate the hysteresis parameters of any wood joint or structural system are given. Hysteresis shapes produced by the proposed model are shown to compare reasonably well with experimental hysteresis of wood joints with: (1) yielding plate, (2) yielding nails, and (3) yielding bolts. To demonstrate its use, the proposed model is implemented in a nonlinear dynamic analysis program for single-degree-of-freedom (SDF) systems. System response from arbitrary dynamic loading, such as cyclic or earthquake-type loadings, can be computed. Three SDF wood systems are subjected to the Loma Prieta accelerogram to obtain their response time histories. Advantages of using the proposed model over currently available models in nonlinear dynamic analysis of more complex systems are identified. A multidegree-of-freedom shear building model incorporating the proposed hysteresis model is formulated but not implemented on a computer. / Master of Science

Rotating machines such as motors, generators, turbines, etc. are crucial mechanical components of modern industrial and power generation facilities. For proper functioning of these facilities during and after an earthquake, it is essential that the rotating machines in these facilities also function as desired. The dynamics of a rotating machine is quite complex. It is further complicated by the presence of earthquake induced base motions. The response spectrum methods, which are now commonly used for calculating seismic design response of civil structures, cannot be used as such for calculating the design response of rotating machines. In this thesis, a response spectrum method which can be applied to the rotating machines is developed. To develop the response spectrum approach, a generalized modal superposition method is utilized. The random vibration analysis is applied to incorporate the stochastic characteristics of the seismic inputs. The applicability of the proposed response spectrum approach is verified by a simulation study where fifty sets of acceleration time histories are used. The proposed method considers the fact that earthquake induced base motions have several components, including rotational inputs. To define the correlation between the rotational and translational input components of the excitation, the correlation matrix and a travelling seismic wave approaches are used. The numerical results are obtained to evaluate the effect of rotational input components on the response of a rotating machine. It is observed that the rotational components are important only when they are very strong. In actual practice, such strong rotational inputs are not expected to excite rotors which are either directly placed on ground or are placed in common buildings. In the proposed spectrum approach, nevertheless, the effect of rotational input components can be easily incorporated if the correlation between various excitation components is specified. / Master of Science

Soil liquefaction can cause devastating damage and loss and is a serious concern in civil engineering practice. One method for evaluating liquefaction triggering potential is a risk-targeted probabilistic approach that has been shown to provide more consistent and accurate estimates of liquefaction risk than traditional methods. This approach is a “performance-based” procedure which is based off of the performance-based earthquake engineering (PBEE) framework developed by the Pacific Earthquake Engineering Research (PEER) Center. Unfortunately, due to its complexity, performance-based liquefaction assessment is not often used in engineering practice. However, previous researchers have developed a simplified performance-based procedure which incorporates the accuracy and benefits of a full performance-based procedure while maintaining a more simplistic and user-friendly approach. Until now, these simplified performance-based procedures have only been available for the SPT (Standard Penetration Test). With the increasing popularity of the CPT (Cone Penetration Test), a simplified procedure is needed for CPT-based liquefaction assessment. This thesis presents the derivation of a simplified performance-based procedure for evaluating liquefaction triggering using the Ku et al. (2012) and Boulanger and Idriss (2014) models. The validation study compares the results of the simplified and full performance-based procedures. The comparison study compares the accuracy of the simplified performance-based and traditional pseudo-probabilistic procedures. These studies show that the simplified performance-based procedure provides a better and more consistent approximation of the full performance-based procedure than traditional methods. This thesis also details the development of the liquefaction loading maps which are an integral part of the simplified method.

Finite element modeling of laminar shear box testing that consisted of loose sand treated with large diameter prefabricated vertical drains (PVDs), was performed. The objective of the modeling was to evaluate the reliability of the computer program FEQDrain for predicting excess pore pressure ratios (Ru) at sites treated with prefabricated drains. FEQDrain was found to be capable of successfully modeling measured excess pore pressure ratio time histories from the laminar shear box experiment, as long as an appropriate combination of €˜number of equivalent cycles and €˜shaking duration was chosen, and sensitive parameters were in the range of measured values. Hydraulic conductivity, soil compressibility, and cycles to liquefaction are sensitive parameters and govern the computed Ru values.Modeling shows that the loading rate in the laminar shear box (15 cycles at 2 Hz) likely induced higher Ru values than would be expected in a typical earthquake event with a longer duration. The longer duration allows the drains to dissipate pore pressures and prevent liquefaction. The number of equivalent cycles and duration of shaking combinations recommended for various moment magnitudes in the FEQDrain user manual predict lower, but similar Ru versus time curves. Thus, suggesting that PVDs would be equally effective for any size earthquake. However, drains are most effective at preventing liquefaction when earthquake ground motions are long and uniform, rather than short and intense.Results from models in this study compare favorably with those from computer modeling performed by Howell et al. (2014). The individual hydraulic conductivity and compressibility values were different they were somewhat compensating. Similar Ru values can be modeled with different combinations of these parameters.Based on computer analyses, wick drains and 2€ diameter PVDs were found to be relatively ineffective for preventing liquefaction. However, 3€ diameter PVDs are fairly effective but can be overwhelmed during intense shaking. In contrast, 4€ diameter and larger PVDs are significantly more effective.

Finite element modeling of laminar shear box testing that consisted of loose sand treated with large diameter prefabricated vertical drains (PVDs), was performed. The objective of the modeling was to evaluate the reliability of the computer program FEQDrain for predicting excess pore pressure ratios (Ru) at sites treated with prefabricated drains. FEQDrain was found to be capable of successfully modeling measured excess pore pressure ratio time histories from the laminar shear box experiment, as long as an appropriate combination of ˜number of equivalent cycles and ˜shaking duration was chosen, and sensitive parameters were in the range of measured values. Hydraulic conductivity, soil compressibility, and cycles to liquefaction are sensitive parameters and govern the computed Ru values.Modeling shows that the loading rate in the laminar shear box (15 cycles at 2 Hz) likely induced higher Ru values than would be expected in a typical earthquake event with a longer duration. The longer duration allows the drains to dissipate pore pressures and prevent liquefaction. The number of equivalent cycles and duration of shaking combinations recommended for various moment magnitudes in the FEQDrain user manual predict lower, but similar Ru versus time curves. Thus, suggesting that PVDs would be equally effective for any size earthquake. However, drains are most effective at preventing liquefaction when earthquake ground motions are long and uniform, rather than short and intense.Results from models in this study compare favorably with those from computer modeling performed by Howell et al. (2014). The individual hydraulic conductivity and compressibility values were different they were somewhat compensating. Similar Ru values can be modeled with different combinations of these parameters.Based on computer analyses, wick drains and 2 diameter PVDs were found to be relatively ineffective for preventing liquefaction. However, 3 diameter PVDs are fairly effective but can be overwhelmed during intense shaking. In contrast, 4 diameter and larger PVDs are significantly more effective.

Earthquake-induced liquefaction can cause severe damage to infrastructure is a serious concern in civil engineering practice. Post-liquefaction settlement is one of the common effects of liquefaction. The ability to predict and quantify post-liquefaction free-field settlement is a crucial part of seismic design. Many approaches have been developed during the past 50 years to perform liquefaction hazard analysis. The performance-based earthquake engineering (PBEE) framework developed by the Pacific Earthquake Engineering Research (PEER) center is a probabilistic framework that can provide a more accurate and complete seismic hazard analysis than other traditional methods. However, the PBEE framework is not widely used in routine projects due to its complexity.Previous researches have been performed to develop simplified performance-based procedures that can combine the simplicity of a traditional method and the accuracy of the full performance-based method. Unfortunately, these simplified performance-based procedures are only available for SPT. With the increase use of CPT, there is a need to develop simplified performance-based procedures for CPT. This study develops simplified performance-based procedures for the assessment of post-liquefaction free-field settlement for CPT, using the Boulanger and Idriss (2014) and the Ku et al. (2012) triggering models. The Juang et al. (2013) model, which is a probabilistic version of the Ishihara and Yoshimine (1992) model, is used in this study to performance free-field settlement calculations. The simplified procedure is based on the idea of liquefaction reference parameter maps. Reference values obtained from these parameter maps are then adjusted, using correction equations, to site-specific conditions. This study presents the deviations of the correction equations for the simplified performance-based procedure. The simplified procedure will then be validated in which 18 cities across the United States are analyzed using both the simplified procedure and the full performance-based procedure. The simplified performance-based procedure is shown to reasonably estimate the results of the full performance-based procedure. Finally, a study is performed to compare the accuracy and consistency of the simplified performance-based and the conventional pseudo-probabilistic procedures. The simplified performance-based procedure is found to provide better approximations of the full performance-based procedure with more consistency and precision.

Pages vi, 34, 68, 158, 208 and 226 are blank and therefore omitted. / <p> To assess the ductility of shear walls under earthquake loading, more experimental evidence is strongly needed. Ductile response can be achieved through the development of a flexural plastic hinge at the base characterized by yielding of the vertical reinforcement. The length of the plastic hinge and the ultimate curvatures within this region are the essential parameters affecting the ductility and ultimate displacements of reinforced masonry shear walls. The discrepancies in existing information regarding the length of plastic hinges and ultimate curvature may be attributed to the effects of many shear wall parameters such as distribution and amount of vertical and horizontal steel, level of axial load, and wall aspect ratio. </p> <p> The focus of this study was to evaluate the effect of different parameters on plastic hinge length, energy dissipation, and on general ductility of masonry shear walls. To address the aforementioned goal, six fully grouted reinforced masonry walls were tested under fully reversed cyclic lateral loading. All walls were designed to experience ductile flexural failure. The test matrix was chosen to investigate the effects of the amount and distribution of vertical reinforcement and the level of applied axial load on the lateral loading response and ductility of reinforced masonry shear walls. To examine the effects of these parameters, measurements of the applied loads, vertical and horizontal displacements as well as strains in the reinforcing bars were used to analyze the behaviour of the walls. Also, from these measurements, other quantities used in analysis were determined, including displacement ductilities, curvature profiles, energy dissipation and equivalent plastic hinge length. </p> <p> The results show high ductile capability in the plastic hinge region and very little degradation of strength for cyclic loading. High levels of energy dissipation in the reinforced concrete masonry shear walls were achieved by flexural yielding of the vertical reinforcement. All walls showed increasing hysteretic damping ratios with increase in displacement. Results showed that displacement ductility and energy dissipation were highly sensitive to increases in amount of vertical reinforcement but were less dependent on the level of applied axial stress. The results of this study also showed that the measured plastic zone length decreases with increase of the amount of reinforcement while it is almost the same for the different levels of axial stress. Based on the test results, it was shown that reinforced concrete masonry shear walls may be utilized in high intensity seismic areas with performance meeting or exceeding current expectations. </p> / Thesis / Master of Applied Science (MASc)

<p> The recent urban sprawl in the tectonically active region of California has prompted palaeoseismologists, to find ways of forecasting potentially hazardous earthquakes on existing faults. Electron spin resonance (ESR) can be used to date fault gouge from different regions in a fault zone thereby providing a history of fault movements in a particular region. Therefore, an earthquake frequency pattern can be established and the faults can be rated as to their potential danger. </p> <p> ESR dating of fault gouge is based on the premise that the ESR signals of quartz grains in the gouge have been completely reset by movements on the fault. The elapsed time since faulting is recorded by a gradual charge build up in the quartz corresponding to radioactive decay of radionuclides in the fault gouge matrix. The mechanism of zeroing of the ESR signals in quartz during fault activity is not well understood. In order to better comprehend the zeroing process, the variation of ESR signals, AD and age, with respect to quartz grains size were studied. These parameters are affected by induced stress to a greater extent in the smaller grain sizes. Therefore, with sufficient stress, the smallest grain sizes (smaller than a critical size) will be totally reset and define a "plateau" of equal age. This plateau criteria is used to define total resetting in a fault gouge sample and only these portions of the samples are used for dating. The establishment of an equal age plateau is confirmed for one of the fault samples collected from Southern California. </p> / Thesis / Master of Science (MS)

Yes / Earthquake response spectrum is the most popular tool in the seismic analysis and design of structures. In the case of combined primary-secondary (P-S) systems, the response of the supporting P substructure is generally evaluated without considering the S substructure, which in turn is only required to bear displacements and/or forces imposed by the P substructure (¿cascade¿ approach). In doing so, however, dynamic interaction between the P and S components is neglected, and the seismic-induced response of the S substructure may be heavily underestimated or overestimated. In this paper, a novel CQC (Complete Quadratic Combination) rule is proposed for the seismic response of linear light S substructures attached to linear P substructures. The proposed technique overcomes the drawbacks of the cascade approach by including the effects of dynamic interaction and different damping in the substructures directly in the cross-correlation coefficients. The computational effort is reduced by using the eigenproperties of the decoupled substructures and only one earthquake response spectrum for a reference value of the damping ratio.

No description available.