Thesis (MScEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2005. / The cause of the largest number of faults on the Eskom main transmission system is unknown. It is believed that a non-uniform pollution layer along an insulator string is the reason for these anomalous flashovers. This non-uniform pollution layer results in the highest electric field strength, and thus the highest voltage, across the cleanest and driest discs. There thus exists a strong possibility that the anomalous flashover phenomenon is caused by a combination of mechanisms involving the pollution and air breakdown flashover mechanisms. This research project attempted to prove that flashover of the insulators is possible in accordance with the above model. Various experiments were set up in the high voltage laboratory and at a natural test site with a low source impedance supply attempting to simulate the conditions that lead to flashover in accordance with the hypothesis. All the tests done have not proven the non-uniform light pollution flashover mechanism successfully. However, future research has proposed an air breakdown flashover mechanism in light pollution conditions where the polluted part of the insulator string has a specific non-uniform distribution. Full scale testing in conditions similar to the normal operating conditions is proposed to prove the validity of this new hypothesis.

No description available.

Lake Champlain is a major economic driver for Vermont's tourism economy, as well as a primary source of drinking water for many of the state's residents but nutrient pollution represents a potential threat to ecosystem health and economic well-being. From December 2011 to December 2012 a field trial of an EAF steel slag filter was assessed for its feasibility in treating wastewater originating from Swan Valley Cheese (SVC), in Swanton, VT. The study focuses on a period of the filter's operation from May 4 to October 10, 2012. The plant generates approximately 20,000 gallons per day of high P concentration wash water which is treated in an open aerated lagoon. The filter treated effluent from this lagoon. The major goals of this research were to conduct a field trial of an EAF steel slag filter to evaluate its effect on total P (TP), dissolved reactive P (DRP), and total suspended solids (TSS). Research was also conducted on pH reduction for filter effluent. Results indicate that the filter removed 95.83% of TP, 96.65% of DRP, and 52.25% of TSS. Average pH effluent was measured at 10.12 ±1.55. Additionally, a field study was conducted on sampling two unlined bioretention systems treating urban stormwater runoff. Methods used are presented and methodological considerations for future studies are presented to guide researchers in more effective and efficient methods for obtaining influent and effluent samples from bioretention systems that are not necessarily designed for sampling.

L’étude présentée ici entre dans la problématique générale des arcs électriques intervenant dans des applications industrielles telles que le soudage, le découpage, le traitement des déchets. Ce travail constitue une première phase de modélisation de cette étude générale. Le plasma est décrit par un ensemble d'équations de conservation de fluide et de l’électromagnétisme, complétés par des propriétés thermodynamiques et des coefficients de transport appropriés, en formant un système d’équations non linéaires fortement couplées. Ces équations sont écrites en supposant l’équilibre thermodynamique local, une symétrie cylindrique et un écoulement laminaire stationnaire. Ce système d’équations est résolu à l’aide du logiciel commercial FLUENT de type CFD fondé sur l’approche des volumes finis. Pour pouvoir utiliser la partie solveur nous avons résolu notre modèle en utilisant les routines UDF Users-Defined-Function. Dans une première partie, nous présentons la validation du modèle à deux dimensions et à 100 A dans l’argon par des résultats de la littérature. Cette comparaison laisse apparaître un accord satisfaisant sur les profils de température dans la colonne de plasma et des différences dans les zones proches des électrodes dues aux conditions aux limites. Dans une deuxième partie, nous présentons une étude expérimentale, à l’issue de laquelle on constate que les profils de température expérimentaux sont en accord avec ceux du modèle dans la zone de colonne positive. / The study presented here enters the general problem of electric arc involved in industrial applications such as welding, cutting, waste treatment. This work constitutes the first numerical phase of modeling of this general study. The plasma is described by a set of fluid conservation equations, electromagnetic equations complemented by suitable thermodynamic and transport properties, forming a strongly coupled non-linear system. These equations are written assuming local thermodynamic equilibrium, a cylindrical symmetry and steady laminar flow. This system of equations is solved using commercial software FLUENT CFD-type based on finite volume algorithm. To use the solver part we solved our model using UDF macro Users-Defined-Function. In the first part, we present the validation of the two dimensional model in and 100 A in argon with the literature results. A detailed analysis of various characteristic quantities is presented. This comparison reveals a good agreement of the temperature profiles in the column plasma and differences in electrode areas due to boundary conditions. In a second part, we present an experimental study, the experimental temperature profiles are consistent with the model in the column area which means that the model is validated in the column of plasma.

<p>Steel heating and melting processes consume the majority of the energy used in advanced short-process steelmaking practices. Economic and environmental pressures from energy consumption drive the research to improve the furnace operation efficiency and energy efficiency. The goal of this research is to utilize computational fluid dynamics (CFD) modeling to provide useful tools and recommendations on the steel heating and melting practices in the steelmaking process. The steel slab reheating process, the steel scrap preheating process and the steel scrap melting process are studied.</p> <p> </p> <p>A transient three-dimensional (3-D) CFD model was developed to simulate the flow characteristics, combustion process and multi-scale, multi-mode heat transfer inside the reheating furnace. The actual geometry of an operating industrial furnace was used and typical operating conditions were simulated. Specific walking speeds of slabs in production were modeled using a dynamic mesh model which is controlled by a user-defined function (UDF) solved using ANSYS Fluent. Fuel variations at different zones with respect to time were also considered. The model was validated with instrumented slab trials conducted at the SSAB Mobile (Alabama) mill. The temperature field in the furnace and the temperature evolution of a slab predicted by the CFD model are in good agreement with those obtained from the instrumented slab trials. Based on the simulation results, the slab reheating process and the temperature uniformity of a slab at discharge were able to be properly evaluated. In addition, a comprehensive two-dimensional (2-D) numerical heat transfer model for slab reheating in a walking beam furnace was developed using the finite difference method. An in-house code was developed. The model is capable of predicting slab temperature evolution during a reheating process based on real time furnace conditions and steel physical properties. The model was validated by using mill instrumented slab trials and production data. The results show that the temperature evolution predicted by the model is in good agreement with that measured by the thermocouples embedded in the instrumented slab. Compared with 3-D CFD simulation of a reheating process, this 2-D heat transfer model used for predicting slab temperature evolution requires less computing power and can provide results in a few seconds. A graphical user interface was also developed to facilitate the input and output process. This is a very convenient and user-friendly tool which can be used easily by mill metallurgists in troubleshooting and process optimization.</p> <p> </p> <p>CFD models for steel scrap preheating and melting processes by the combined effects of the heat source from both oxy-fuel combustion and electric arc were also developed. The oxy-fuel burners firing natural gas (NG) are widely used in EAF operation during the scrap preheating and melting stages. In order to understand the role of oxy-fuel combustion and potentially increase the energy input from NG while decreasing the electricity consumption, numerical simulation of scrap preheating by oxy-fuel combustion in an EAF was firstly conducted. A 3-D CFD model was developed with detailed consideration of gas flow, oxy-fuel combustion, heat transfer between gas and solid scrap and scrap oxidation. The model was validated by a small-scale experimental study and applied onto a real-scale EAF.</p> <p> </p> <p>Scrap melting in bath is comprehensively studied with a CFD model developed to simulate the melting in bath process under given operating conditions. Two sub-models were developed for model integration: steel melting model and coherent jet model. The multiphase volume of fluid (VOF) model and the enthalpy-porosity technique are applied to describe the steel melting process. The coherent jet model calculates the gas jet momentum and is integrated into the flow model to calculate its effect on the fluid flow in the bath. The electric arc was treated as a heat flux to represent the heat transfer from the electric arc during the melting process. Model validations were conducted for each sub-model to ensure their accuracy. Parametric studies were also carried out to obtain useful information for real practice. </p><p>Overall, the CFD models developed in this research work have demonstrated value in improving energy efficiency in the energy-intensive steelmaking processes. The developed CFD models also provide insights for better understanding of the multi-physics processes.<br></p> <p> </p>

Este trabalho tem por objetivo estudar o aproveitamento do pó de aciaria elétrica (PAE) na sinterização de minério de ferro visando a eliminação de zinco. Primeiramente, foi feita uma caracterização física e química do resíduo através de análises químicas, granulométricas, morfológicas e de difração de raios-X. O minério de ferro, principal componente do processo de sinterização, foi caracterizado através de análise química, granulométrica e de umidade. Em seguida, foram fabricadas micropelotas de 3,0 a 5,0mm de diâmetro compostas por 70% de PAE e 30% de moinha de coque, que foram classificadas por peneiramento e secas em esfufa. Depois de aglomerado, o resíduo foi incorporado na sinterização de minério de ferro em diferentes proporções, condições de processo e formas de adição (micropelotas, undersize da micropelotização com granulometria entre 1,0 e 2,0mm, ou mistura de PAE e coque em pó). A cada processo de sinterização foram retiradas amostras de sínter, os materiais foram analisados através de Microscópio Eletrônico de Varredura (MEV), macroscopia e análises químicas por espectrofotometria de absorção atômica para verificar o teor de zinco. Amostras de misturas não sinterizadas também foram submetidas a análises químicas para determinar a quantidade inicial de zinco, ou seja, verificar a quantidade de zinco contido na mistura antes do processo de sinterização. Mediante a comparação do teor de zinco das amostras não sinterizadas com os sínteres, foi possível determinar a eliminação de zinco nos ensaios realizados. Aproximadamente 92% de zinco foi eliminado (junto com os gases de saída) com a incorporação de 10% de micropelotas na mistura a sinterizar. Os resultados mostraram que a eliminação do metal no processo é proporcional à relação redutor/resíduo. / The aim of this work was to study the use of electric arc furnace dust (EAFD) in iron ore sintering process aiming zinc elimination. Firstly, physical and chemical characterizations of the waste were made using X-ray diffraction, microscopy, chemical and size analyses. Iron ore is the main component of the sintering process, this material was characterized by chemical, size and humidity analyses. After, micropellets composed of EAFD 70% and coke breeze 30% with diameters of 3.0-5.0 mm were produced, then they were dried in kiln and classified by sieving. The pellets were incorporated into the iron ore sintering charge using differents proportions, process conditions and addition forms (micropellets, undersize with diameters of 1.0-2.0 mm, or a mixture of EAFD and coke breeze). Sintered samples were collected in each sintering process. These materials were analyzed by scanning electron microscopy (SEM), macroscopy and chemical analysis using atomic absorption spectrophotometry in order to determine the zinc content. Samples of not sintered mixtures were also characterized by chemical analysis aiming the determination the initial amounts of zinc, i.e. in order to check the zinc amounts present in the mixture before the sintering process. The comparation between the zinc contents of sintered samples and not sintered allowed to determine the elimination of zinc during the experiments. About 92% of zinc was eliminated (along with the output gas) with the incorporation of 10% of micropellet in the sintering mixture. Results showed that the zinc elimination in the process is proportional to the ratio reducer/waste.

A redução no volume de resíduos produzidos, industriais e agrícolas, vem se tornando uma exigência constante em todos os processos de produção. A falta de espaço físico para a disposição destes resíduos, a contaminação ambiental causada por eles, além da necessidade de preservação dos recursos naturais não-renováveis e da diminuição do consumo de energia e emissão de poluentes, tornam a reciclagem e a reutilização dos resíduos uma alternativa bastante atraente. A construção civil apresenta-se como um setor bastante apto à utilização de técnicas de reaproveitamento de resíduos, provenientes das mais diversas indústrias. Além de todos os benefícios ambientais, este reaproveitamento, pela construção civil, pode gerar recursos financeiros, bem como, possibilita a melhora das características de alguns materiais de construção, e pode diminuir o custo de construção, fator importante, quando se avalia o déficit de habitacional existente no Brasil. Neste trabalho, desenvolveu-se um estudo baseado no aproveitamento de escória de aciaria elétrica, resíduo gerado a partir da reciclagem do aço, empregada como agregado para concreto de cimento Portland, em substituição total ou parcial dos materiais convencionais. Os resultados obtidos apontaram para a viabilidade de utilização deste resíduo como agregado. / The reduction on the volume of produced wastes, from industries or agriculture, is becoming a current demand in all production processes. The lack of space to dispose these wastes, the environment contamination caused by them, besides the necessity to preserve the non-renewable natural resources, to reduce energy consumption and greenhouse gas emission , are making wastes recycling and reutilization an interesting alternative. The civil construction presents itself as a field quite able to utilize techniques to reuse wastes from different industries. Besides all the environmental benefits, this reuse by the civil construction can create new profits, as well as, the improvement of the characteristics of some construction materials and it can also decrease the costs of the construction, which is a major factor, considering the Brazilian habitation deficit. In the present work a study was developed based on the reutilization of the electric arc furnace slag, a metallurgic waste from the steel recycling process, employed as an aggregate to the concrete of Portland cement, totally or partially replacing the conventional materials. The obtained results indicate this waste reutilization viability.

O setor siderúrgico, assim como os demais setores da indústria, vem buscando alternativas para a redução dos custos de produção e aumento de produtividade. Em aciarias elétricas, os principais custos de produção do aço podem ser divididos, de forma simplificada, entre o custo dos insumos e o custo das matérias primas. Os refratários estão entre os cinco maiores custos na produção do aço em usinas semi-integradas. Entretanto, o conhecimento detalhado da microestrutura e do comportamento desses materiais ainda é bastante restrito aos seus fabricantes. Tendo em vista a importância dos refratários na produção do aço, este trabalho teve como objetivo gerar conhecimento acerca de sua microestrutura e comportamento em operação, com foco na diminuição do consumo e maximização dos lucros da empresa. Para tal, com o intuito de conhecer detalhadamente sua microestrutura e prever seu desempenho, foram realizadas análises de caracterização em laboratório e testes que simularam as condições de operação. Após os testes laboratoriais, os materiais selecionados foram testados em operação em forno elétrico a arco, buscando encontrar o melhor conjunto de materiais sob o ponto de vista de estabilidade do processo e custo de refratários. O cenário que apresentou melhores resultados em relação à performance e ao consumo específico foi a configuração A, onde foram utilizados os tijolos A, massa de soleira X, massa de reparo K e canal EBT P. Além disso, a substituição do tijolo C pelo tijolo A gerou uma redução de custo de 40%, e o conhecimento gerado com a caracterização do canal EBT proporcionou uma redução de 29,9% no preço desse item. / The steel industry, like other sectors of the industry, is seeking alternatives to reduce production costs and increase productivity. In electric steelworks, the main steel production costs can be divided, in a simplified way, between the cost of inputs and the cost of raw materials. Refractories are among the five largest costs in steel production in semi-integrated mills (mini-mills). However, detailed knowledge of the microstructure and behavior of these materials is still quite restricted to their manufacturers. Given the importance of the refractories in the production of steel, this study aimed to generate knowledge about their microstructure and behavior in operation, focusing on the reduction of consumption and maximization of profits. For that, in order to know in detail the microstructure and predict its performance, characterization analyzes and tests simulating the operating conditions were performed in the laboratory. After laboratory tests, the selected materials have been tested in operation in electric arc furnace, seeking to find the best set of materials from the point of view of stability of the process, and cost of refractories. The scenario that best results presented, in terms of performance and the specific consumption, was Configuration A, where bricks A, ramming mix X, repair mix K and EBT P were used. Moreover, the replacement of Brick B by brick A, generated a cost reduction of 40%, and the information gathered with the characterization of EBT, reduced the price of that item by 29.9%.

O Pó de Aciaria Elétrica (PAE) é um resíduo sólido originado na fabricação de aços em Fornos Elétricos a Arco (FEA), classificado como resíduo perigoso pela ABNT NBR 10004- 2004. Isto porque ele contém metais nocivos ao meio ambiente (como chumbo e cádmio), embora seja constituído, em sua maior parte, pelos elementos ferro, zinco e oxigênio. Devido aos custos onerosos para disposição e por tratar-se de resíduo perigoso, a indústria procura pela possibilidade de retorno ao processo produtivo do aço. Uma das alternativas é a reintrodução na aciaria elétrica através de aglomerados autorredutores como parte da carga do FEA. Neste trabalho, são produzidas misturas autorredutoras contendo PAE e coque de petróleo, apresentando as correspondentes caracterizações químicas e físicas. Através de ensaios termogravimétricos é feita uma avaliação do comportamento destas misturas, mostrando a possibilidade do emprego desta técnica na aferição prática do teor ótimo de coque, em aglomerados. Além disto, foram produzidas pelotas autorredutoras através do uso de um disco laboratorial, sendo as pelotas submetidas a testes físicos e mecânicos, com uso de aglomerantes e também testes de autorredução em fornos mufla e em aparato experimental. Como resultados destes experimentos pode-se concluir que o cimento Portland ARI e a combinação de cal hidratada com cinza de casca de arroz possuem melhor resistência a compressão frente aos outros ligantes utilizados. O grau de metalização obtido para a maior parte das amostras não passou de 35%. A remoção de zinco foi de aproximadamente 85%, para temperatura de 1100 ºC, com 45 minutos e com 10% de coque de petróleo. Isto indica a possibilidade de enriquecimento da nova poeira gerada em zinco. Fato este que agrega valor para tratamento do resíduo em outros processos externos. / The Electric Arc Furnace Dust (EAFD) is a solid waste generated by electric steelmaking, in Electric Arc Furnaces (EAF), being considered a hazardous waste by the Environmental Protection Agency. That is because of its harmful metals, although it is composed, in majority, by elements iron, zinc and oxygen. Due to high costs involved for its disposal and because it is a hazardous waste, industry seek for the possibility of returning the EAFD back to the steelmaking process. One of the alternatives is by reintroduction via electric meltshop through self-reducing agglomerates as part of the furnace burden. In this work, self-reducing mixtures of EAFD and petroleum coke were produced, showing as result corresponding chemical and physical characterizations. Using thermogravimetric tests, an evaluation of the mixtures behavior was carried out, demonstrating the possibility of using this technique in a practical measurement of optimal content of coke, in agglomerates. Furthermore, selfreducing pellets were pelletized using a laboratorial disc, with these agglomerates being tested in physical and mechanical strength essays, with different binders employed and also selfreduction tests in vertical electric furnace and experimental apparatus. As part of the results it could be concluded cement and the combination between hydrated lime and rice husk ash achieved the best results, in compressive strength, comparing to other binders. The metallization degree for almost all samples achieved a maximum of 35%. Zinc removal, for temperatures around 1100 ºC, in an experiment of 45 minutes and using 10% of petroleum coke, was approximately 85%. It indicates the dust to be enriched with zinc. This fact adds value to the waste for treatment in other processes.

O pó de aciaria elétrica é um importante subproduto da indústria siderúrgica devido ao seu alto teor de zinco. Assim, tecnologias vêm sendo desenvolvidas visando seu aproveitamento, sendo o forno Waelz a mais difundida delas atualmente. No entanto, sua operação, por contar com um forno rotativo de grandes dimensões que abriga uma infinidade de fenômenos físico-químicos, apresenta difícil previsibilidade ab initio. Por essa razão, este trabalho faz uso de uma ferramenta avançada da termodinâmica computacional, destinada à modelagem de processos, chamada SimuSage, a fim de modelar o seu comportamento. Para a criação do modelo utilizou-se também uma base de dados termodinâmicos advinda do software FactSage e a plataforma de desenvolvimento Lazarus. Com base em dados e resultados operacionais da literatura, foi possível realizar simulações nos modos adiabático e isotérmico, comparando os resultados com os da prática industrial. Constatou-se uma grande capacidade do modelo de reproduzir os resultados da literatura, mesmo quando não há muita informação para aferição dos parâmetros, gerando boa concordância com a composição química relatada dos produtos Óxido Waelz e Escória Waelz. / The electric arc furnace dust is an important by-product of the steel industry due to its high content of zinc. Thus, technologies have been developed aiming for its use, and the Waelz Kiln is the most widespread of them today. However, counting on a very large rotary kiln that houses an infinity of physico-chemical phenomena, its operation is difficult to predict ab initio. For this reason, in order to model its behaviour this work uses an advanced tool of computational thermodynamics designed to process modelling, called SimuSage. To create the model, a thermodynamic database, provided by the FactSage software, as well as a development platform, Lazarus IDE, were also used. Based on operational data and results from de literature, it was possible to perform simulations on both adiabatic and isothermal modes comparing its results with the industrial practice. A great capability of the model to reproduce results from the literature was found, even when there is not much information for the parameters calibration, generating good agreement regarding the reported chemical composition for the products, Waelz Oxide and Waelz Slag.