Philosophiae Doctor - PhD / Ammonia has attracted attention as a possible fuel for direct fuel cells since it is easy to handle under low pressure, costs only slightly higher than methanol and can easily be cracked down into hydrogen and nitrogen. At low temperature, ammonia oxidation on noble metal electrodes is a sluggish reaction and efficient catalysts are required to convert ammonia to nitrogen and hydrogen at reasonable reaction rates. In this thesis, I present polycrystalline and oriented nanoalloys synthesised at room temperature in aqueous media and their catalytic effects on the oxidation of ammonia. The electro-oxidation of ammonia on palladium-goldsilver (PdAuAgNPs) ternary nanoalloys was systematically studied in alkaline solution of potassium hydroxide (KOH) by cyclic voltammetry (CV). The PdAuAg nanoalloys were prepared through a facile synthesis with ascorbic acid as a reductant and polyvinylpyrrolidone (PVP) as a stabilising agent from aqueous solutions of PdCh/HAuCI4.3H20/AgN03 mixtures. UV-visible spectroscopy was used to confirm the complete reduction of the metal ions; absorption peaks observed at 260 nm, 285 nm and 420 nm for Ag", Au3+ and Pd2+ ions respectively, disappeared after reduction indicating a complete reduction of the metal ions to zero-valent nanoparticles. High resolution transmission electron microscopy (HR TEM) revealed the formation of crystalline nonaggregated 25-35 nm sized nanoalloys. The elemental composition of the nanoalloys measured using energy dispersive X-ray spectroscopy (EDX) showed the presence of the three elements; Pd, Au and Ag. The well-dispersed non-agglomerated PdAuAg nanoalloys exhibited a reduced overpotential and a 33%, 400%,82% and 54% increase in current density for ammonia electro-oxidation compared to Pd, PdAg, PdAu nanoparticles and bare Pt electrode, respectively. The much improved current density of the well-dispersed PdAuAg nanoalloys is attributed to the increased electrochemically active surface area of the nanoalloys. This electro catalytic behaviour of the PdAuAg nanoalloys for ammonia oxidation in KOH solutions provides a promising route for development of low-cost and high performance electro catalyst for electro-oxidation of ammoniaMoreover, ammonia oxidation on platinum surfaces has been found to be a very structure sensitive reaction which takes place almost exclusively on Pt(100) surfaces. I report for the first time the preparation of sodium polyacrylate-capped Pt(100)Pd, pte 1OO)Au, pte 1OO)Ir, Pt(IOO)Rh, Pt(100)PdAu, Pt(100)IrAu, Pt(IOO)PdIr and Pt(IOO)RhAu nanoalloys. The reduction of the metal ions to nanoparticles was confirmed by UV-visible spectroscopy while the shapes and the structures of the nanoparticles were studied using HRTEM and CV. HRTEM analysis showed well distributed non-agglomerated 5-20 nm semi-spherical and cubic nanoalloys with lattice fridges on their surfaces indicating the crystalline nature of the nanoalloys. Pt(100) nanoalloy systems showed particles with triangular and cubic shapes. The existence of the preferentially cubic shaped nanoparticles in the samples indicated that the nanoalloys had some (100) sites orientation/a significant amount of (100) sites at their surfaces. The CV of the nanoparticles in the hydrogen adsorption/desorption region (-200 mV to 100 mV vs. Ag! AgCl) was used to obtain qualitative information about the surface structure of the nanoparticles. The voltammogram of oriented Pt(100) nanoparticles showed very clearly the presence of adsorption states associated with (110) sites, (100) domains and (l00) sites at -131 mV, -34 mV and 29 mV, respectively. The companson of this voltammetric profile with that obtained for a Pt(100) single crystal electrode clearly points out that the synthesised Pt nanoparticles have a high density of (100) sites. However, the peak that was observed at 29 mV in the CV of Pt(100) nanoparticles was not present in the vo ltammo grams of the Pt(100) nanoalloy systems confirming the formation of the nanoalloys. The results reported in this work demonstrate the importance of controlling the intrinsic structural properties of Pt nanoparticles; in terms of nature of the active sites and the effect of adding adatoms (such as Au, Pd, Rh, Ir) in order to understand their catalytic properties. The electrochemical activities of these nanoparticles for ammonia oxidation in basic medium showed an increase of over 100% current density compared to Pt electrode. Pt(lOO)RhAu nanoalloys showed the highest catalytic properties while Pt(lOO)PdAu had the lowest as shown in the trend: Pt(lOO)RhAu > Pt(lOO)PdIr > Pt(lOO) > Pt(lOO)IrAu > Pt(lOO)Pd> Pt(lOO)Rh > Pt(lOO)Au > Pt(lOO)Ir > Pt(lOO)PdAu. The synthesised oriented nanoalloys were further interrogated towards the oxidation of hydrazine as a fuel for hydrazine fuel cells. The oriented Pt(lOO) nanoparticles and Pt(lOO) nanoalloy systems exhibited over 1000% increase in current density and reduced oxidation overpotential compared to bare glassy carbon electrode. These excellent catalytic properties are attributed to the increased surface area and the presence of (100) sites which favour the oxidation of hydrazine.

Two major challenges that impede fuel cell technology breakthrough are the insufficient activity of the electrocatalysts for the oxygen reduction reaction and their degradation during operation, caused by the potential-induced corrosion of their carbon-support upon fuel cell operation. Unsupported electrocatalysts derived from tailored noble-metal nanostructures are superior to the conventional carbon-supported Pt nanoparticle catalysts and address these barriers by fine-tuning the surface composition and eliminating the support. Herein, recent efforts and achievements in the design, synthesis and characterization of unsupported electrocatalysts are reviewed, paying special attention to noble-metal aerogels, nano/meso-structured thin films and template-derived metal nanoarchitectures. Their electrocatalytic performances for oxygen reduction are compared and discussed, and examples of successful catalyst transfer to polymer electrolyte fuel cells are highlighted. This report aims to demonstrate the potential and challenges of implementing unsupported catalysts in fuel cells, thereby providing a perspective on the further development of these materials.

Printed circuit board manufacturing involves subtractive copper (Cu) etching where fine features are developed with a specific spatial resolution and etch profile of the Cu interconnects. A UV-Vis ATR metrology, to characterize the chemical transitions, has been developed to monitor the state of the bath by an in-situ measurement. This method provides a direct correlation of the Cu etch bath and was able to predict a 35% lower etch rate that was not predicted by the three current monitoring methods (ORP, specific gravity, and conductivity). Application of this UV-Vis ATR probe confirmed that two industrial etch baths, in identical working conditions, confirmed a difference in Cu2+ concentration by the difference of the near IR 860nm peak. The scope of this probe allowed chemically specific monitoring of the Cu etch bath to achieve a successful regeneration for repeated use. Interlayer dielectrics (ILDs) provide mechanical and electrical stability to the 3D electrical interconnects found in IC devices. It is particularly important that the structural support is created properly in the multilayered architecture to prevent the electrical cross signaling in short range distances. A combined multiple internal reflection and transmission FTIR has been employed for the characterization of silicon oxycarbonitride (SiOCN) films. These dielectric low-k films incorporate various functional groups bonded to silicon and require chemical bonding insight in the transformation and curing process. Distinct SiOx bonding patterns were differentiated, and the structure of the films can be predicted based on the amount of Si network and caged species. Further optimization of the FTIR analysis must minimize interference from moisture that can impact the judgement of peak heights. To accommodate this, a high-quality glove box was designed for dry air feedthrough to achieve a 95% moisture reduction during analysis, where less than 0.1 mAbs of moisture is detected in the spectra (without additional correction). The glove box allows for the rapid analysis of multiple sample throughput to outpace alternative characterization methods while retaining low spectral noise and a dry environment for 24/7 analysis. There is a great need to identify new catalysts that are suitable for tackling current economic demands, one of which is the nitrogen reduction reaction (NRR). The development of the surface enhanced infrared absorption spectroscopy (SEIRAS) has been applied to characterize the NRR mechanisms on the vanadium oxynitride electrocatalyst. Electrochemical measurements demonstrate NRR activity that is up to three times greater in the presence of N2 than the control Ar. FTIR operando suggests that a considerable number of intermediates were formed and continued to increase in absorbing value under an applied potential of -0.8 V vs Ag/AgCl. XPS results of the post-NRR film suggest a restricting of the film where vanadium oxynitride films are prone to instabilities under the possible MvK mechanism. After 90 minutes of NRR, the NH3 generated was approximately 0.01 ppm was calculated for through the salicylate colorimetric method. On-going efforts are focusing on optimizing the vanadium oxynitride film by the tuning of the oxynitride ratios and crystalline properties to promote the formation of V≡N: during the nitrogen reduction reaction.

The ever increasing demand for energy due to over consumption of non-renewable fossil fuels has emphasized the need for alternate, sustainable and efficient energy conversion and storage systems. In this direction, electrochemical energy conversion and storage systems involving various fundamental electrochemical redox processes such as hydrogen evolution (HER), oxygen reduction (ORR), oxygen evolution (OER), hydrogen oxidation (HOR) reactions and others become highly important. Electrocatalysts are often used to accelerate the kinetics of these reactions. Platinum (Pt), ruthenium oxide and iridium oxide (RuO2 and IrO2) are known to be the state of the art catalysts for several of these reactions due to favouarable density of states (DOS) near the Fermi level, binding energy with the reactant species, chemical inertness etc. Apart from HER, OER and ORR, chlorine evolution reaction (Cl-ER) is another industrially important reaction associated with water purification, disinfection, bleaching, chemical weapons and pharmaceuticals. Dimensionally stable anodes (RuO2/IrO2 mixed with TiO2 on Ti) are the most commonly used catalysts for this process. Issues related to surface poisoning, corrosion and cost of the catalysts, in addition to selectivity and specificity towards a particular reaction are various aspects to be addressed. For example, Pt is not very specific for ORR in presence of methanol in addition to high cost and corrosion in certain media. On the other hand, DSA can efficiently catalyze both OER and Cl-ER, and hence there is overlap of the two processes in the potential range available. There is an on going search for efficient, cost-effective, stable catalysts that possess high specificity for a particular redox reaction. Towards this goal, the present study explores certain layered (phospho)chalcogenides for catalyzing HER, ORR, OER and Cl-ER. The present thesis is structured in two parts, where the first part explores the multi-functional catalytic aspects of new classes of compounds based on layered transition metal mixed chalcogenides (MoS2(1-x)Se2x) and ternary phosphochalcogenides (FePS3, FePSe3 and MoPS). In addition, lithium insertion and desinsertion has been studied with the aim of using the layered materials for rechargeable batteries. The second part of the thesis explores organic electrode materials with active carbonyl groups such as rufigallol, polydihydroxyanthrachene succinic anhydride (PDASA) as battery electrodes. Additionally, covalently functionalized transition metal phthalocyanines with reduced graphene oxide are studied as counter electrodes in dye sensitized solar cells (DSSCs). MoS2(1-x)Se2x (x = 0 to 1) compositions are solid solutions of MoS2 and MoSe2 in different ratios. They crystallize in hexagonal structure with space group P63/mmc (D6h4) having Mo in trigonal prismatic coordination like the pristine counterparts. X-Ray diffraction studies reveal that Vegard’s law (figure 1a) is followed and hence complete miscibility of MoS2 and MoSe2 is established. MoS2(1-x)Se2x (x = 0 to 1) are layered in nature and the layers are held together by long range, weak van der Waal’s forces. This gives us the flexibility of exfoliation to produce corresponding few-layer materials (figure 1b). Figure 1. (a) Variation of lattice parameter corresponding to (002) reflection of MoS2(1-x)Se2x with different x values. (b) Scanning electron micrograph of few-layer MoS2(1-x)Se2x (x = 0.5). The electrocatalytic activity of the few-layer sulphoselenides have been studied towards HER in aqueous 0.5 M H2SO4 and towards Cl-ER in 3 M aqueous NaCl (pH = 3) solution. The mixed chalcogenides exhibit very good activities for both HER and Cl-ER as compared to the activity of their pristine counter parts (i.e. MoS2 and MoSe2) (figures 2a and 2b). Electrocatalytic activity on different compositions reveal that MoS1.0Se1.0 exhibits the maximum activity. Additionally, it has been observed that MoS1.0Se1.0 shows high specificity for Cl-ER with negligible interference of OER. Figure 2. Voltammetric data for (a) hydrogen evolution reaction (in 0.5 M aqueous H2SO4) and (b) chlorine evolution reaction (in 3 M aqueous NaCl solution, pH = 3) on MoS2(1-x)Se2x (x = 0, 0.5, 1). Figure 3. (a) XRD pattern of MoS2(1-x)Se2x (x = 0.5) electrode after a cycle of Li insersion and deinsersion (red) along with as-synthesized material (black) (b) Cycling behaviour of rGO supported (black) and pristine (red) MoS2(1-x)Se2x (x = 0.5) as electrode in rechargeable lithium-ion battery. The equiatomic MoS1.0Se1.0 has also been studied as an anode material for rechargeable lithium batteries. The cyclic voltammogram and characterization after charge-discharge cycle (figure 3a) indicate intercalation of Li with in the layers followed by conversion type formation of Li-S and Li-Se type compounds. The pristine material shows continuous capacity fading while the composites of sulphoselenides functionalized with conducting carbon supports such as rGO, MWCNT, super P carbon, toray carbon show marked improvement in capacity as well as cycling behavior. The rGO functionalized MoS1.0Se1.0 reveals ~1000 mAh/g of stable specific discharge capacity for 500 cycles (figure 3b). In the next two chapters, new class of transition metal-based layered materials FePS3 and FePSe3, containing both P and chalcogen (S and Se) is indroduced for electrocatalysis. FePS3 crystallizes in monoclinic symmetry with an indirect band gap of ~1.55 eV while FePSe3 possesses rhombohedral crystal structure with comparatively low band gap (~1.3 eV) as shown in figure 4a. The FePS3 and FePSe3 have been exfoliated as has been done for MoS1.0Se1.0 (liquid exfoliation method) using acetone as the solvent. Stable colloids with few-layer nanosheets having lamellar morphology and lateral sizes of ~100 to 200 nm are obtained. Electrical characterization indicates that they are semiconducting and the conductivity of the Se analogue is ~50 times higher than that of the S analogue (figure 4b). Figure 4. (a) Catholuminescence of FePX3 ( X = S and Se) reveals the band gap of the material. Band gap of the S analogue is 1.52 eV and that of the Se analogue is 1.33 eV (b) Resistivity of FePX3 ( X = S and Se) as a function of temperature. The tri-functional electrocatalytic activities on rGO-few layer FePX3 (X = S and Se) have been evaluated for HER over a wide pH range (0.5 M H2SO4, 0.5 M KOH, phosphate Figure 5. Catalytic activity of rGO-few-layer FePX3 (X = S, Se) towards HER in (a) aqueous 0.5 M H2SO4 and (b) 3.5 wt % NaCl solutions. (c) ORR activity of the catalysts in oxygen saturated 0.5 M KOH (d) OER behaviour on the catalysts in 0.5 M KOH at a rotation speed of 1600 rpm. buffer, pH 7 and 3.5 % NaCl), ORR and OER in alkaline media (0.5 M KOH). The studies clearly reveal that both rGO-FePS3 and rGO-FePSe3 exhibit excellent HER activity in acidic media (figure 5a) with high stability. The HER studies in 3.5 wt % aqueous NaCl solution (figure 5b) suggests that the catalysts are effective in evolving hydrogen from sea-water environment. Studies on ORR activity (figure 5c) indicate that the rGO composites of both S and Se analogues follow 4-electron pathways to produce water as the final product. They are also found to be highly methanol tolerant. In the case of OER (figure 5d), XPS characterization of the electrodes after the voltammetric studies reveals the presence of very thin layer of Fe2O3 (not detectable by XRD). All the three reactions (HER, ORR and OER) catalyzed by the Se analogue are better than the S analogue (figure 5). This could be due to the low band gap and high conductivity of FePSe3 as compared to FePS3. The over potential to achieve 10 mAcm-2 current density is ~108 mV for rGO-few-layer FePS3 catalyst where in the case of rGO-few layer FePSe3, it is ~97 mV (table 1). Table 1. Catalytic activities of rGO-few layer FePS3 and rGO-few layer FePSe3 towards HER, ORR and OER. Reaction studied rGO-FePS3 rGO-FePSe3 HER (η @ 10mAcm-2) ~108 mV ~97 mV ORR (peak potential) ~0.81 V ~0.87 V OER (η @ 10mAcm-2) ~470 mV ~430 mV It is likely that there is a strong interaction between FePX3 (metal d-orbital) and rGO, as observed from the downward shift of Fe 2p peak in high resolution XPS studies. This interaction may extend the density of states of metal d-orbitals thereby improving the catalytic activities. The next chapter deals with molybdenum-based phosphosulphide compound (MoPS). Molybdenum-based phosphide catalysts have been explored recently as excellent catalysts for various electrochemical reactions such as HER. It is expected that the catalyst containing both S and P will show positive effects on catalytic activities due to the synergy between S and P. In the present study, P incorporated MoS2 is studied towards HER. The XRD pattern of the as-synthesized crystal suggests the presence of mixed phase of MoS2, MoP2 and MoP while the elemental mapping in microscopy indicates the ratio of Mo, P and S to be 1:1:1. The electrochemical HER in 0.5 M H2SO4 indicates that the activity is improved drastically as compared to bulk and few-layer MoS2. The next section explores the use of different organic electrode materials possessing active carbonyl groups for Li-storage studies. The advantage of the use of carbonyl-based compounds lies in the high reversible activity towards Li ion insersion and de-insersion. Rufigallol (figure 6a) exhibits very stable capacity of ~200 mAh/g (at C/20 rate) upto 500 Figure 6. (a) and (c) Schematic representation of rufigallol and poly-dihydroanthracene succinic anhydride (PDASA) respectively. (b) and (d) Cyclic behaviour of rufigallol (at C/20 rate) and PDASA (at 20 mAg-1 current rate) in Li-storage devices. (e) and (f) represent the coulombic efficiency of rufigallol (at C/20 rate) and PDASA (at 20 mAg-1 current rate) as a function of number of cycles. cycles along (figure 6b) and with very good rate capability. A triptycene-based mesoporous polymer, PDASA (figure 6c) is introduced and explored as efficient electrode material for Li-storage. PDASA exhibits very high capacity of ~1000 mAh/g at a current rate of 50 mA/g upto 1000 cycles (figure 6d). Even at very high current rates (3A/g) excellent cyclability is observed. The mechanistic details of lithium uptake and release are studied using various spectroscopic techniques. In both the cases the coulombic efficiency observed is ~80 to 90 % (figures 6e and f). Figure 7. (a) Digital photograph of the dye sensitized solar cell with rGO-Co-TAPc counter electrode. (b) Photoconversion efficiency of DSSCs with different counter electrodes as mentioned in the figure. (c) Photo conversion efficiency of Pt and rGO-Co-TAPc based DSSCs as function of storage time. (d) Schematic illustration of DSSC wherein the energy level of the counter electrodes and electrolyte are shown for different M-TAPcs. In a slightly different direction, metal phthalocyanine - rGO composites (rGO-M-TAPc; M = Co, Zn, Fe) have been explored as counter electrodes in DSSC. Figure 7a depicts the digital image of a DSSC constructed using rGO-Co-TAPc as the counter electrode. It has been observed that rGO-cobalt tetraamino phthalocyanine (rGO-Co-TAPc) counter electrode exhibits ~6.6 % of solar conversion efficiency (figure 7b) and is close to that of standard DSSC (Pt counter electrode) under identical experimental conditions and are highly stable (figure 7c). Other metal phthalocyanines show less efficiency and is analysed based on the relative positions of HOMO energy levels of the materials and the energy level of the redox system (I-/I3- system) as given in figure 7d. The thesis contains eight chapters on aspects discussed above along with summary and future perspectives given at the end. It is devided into various chapters in two sections, one comprising inorganic chalcogenide-based electrocatalysts and another comprising organic electrode materials. Appendix I discusses the Na-storage behaviour of MoS1.0Se1.0 and appendix II describes the Li-storage behaviour of rGO functionalized benzoquinone and diamino anthraquinone electrode materials.

Multi-metallic aerogels have recently emerged as a novel and promising class of unsupported electrocatalyst materials due to their high catalytic activity and improved durability for various electrochemical reactions. Aerogels can be prepared by a spontaneous one-step gelation process, where the chemical co-reduction of metal precursors and the prompt formation of nanochain-containing hydrogels, as a preliminary stage for the preparation of aerogels, take place. However, detailed knowledge about the homogeneity and chemical distribution of these three-dimensional Pd–Pt aerogels at the nano-scale as well as at the macro-scale is still unclear. Therefore, we used a combination of spectroscopic and microscopic techniques to obtain a better insight into the structure and elemental distribution of the various Pd-rich Pd–Pt aerogels prepared by the spontaneous one-step gelation process. Synchrotron-based extended X-ray absorption fine structure (EXAFS) spectroscopy and high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) in combination with energy-dispersive X-ray spectroscopy (EDX) were employed in this work to uncover the structural architecture and chemical composition of the various Pd-rich Pd–Pt aerogels over a broad length range. The Pd80Pt20, Pd60Pt40 and Pd50Pt50 aerogels showed heterogeneity in the chemical distribution of the Pt and Pd atoms inside the macroscopic nanochain-network. The features of mono-metallic clusters were not detected by EXAFS or STEM-EDX, indicating alloyed nanoparticles. However, the local chemical composition of the Pd–Pt alloys strongly varied along the nanochains and thus within a single aerogel. To determine the electrochemically active surface area (ECSA) of the Pd–Pt aerogels for application in electrocatalysis, we used the electrochemical CO stripping method. Due to their high porosity and extended network structure, the resulting values of the ECSA for the Pd–Pt aerogels were higher than that for a commercially available unsupported Pt black catalyst. We show that the Pd–Pt aerogels possess a high utilization of catalytically active centers for electrocatalytic applications based on the nanostructured bimetallic framework. Knowledge about the homogeneity and chemical distribution of the bimetallic aerogels can help to further optimize their preparation by the spontaneous one-step gelation process and to tune their electrocatalytic reactivity.