Thesis (Ph. D.)--State University of New York at Binghamton, Thomas J. Watson School of Engineering and Applied Science, Department of Systems Science and Industrial Engineering, 2009. / Includes bibliographical references.

Thesis (M.S.)--University of Texas at El Paso, 2009. / Title from title screen. Vita. CD-ROM. Includes bibliographical references. Also available online.

Thesis (M.S.)--State University of New York at Binghamton, Department of Systems Science & Industrial Engineering, 2005. / Includes bibliographical references.

Thesis (Ph. D.)--State University of New York at Binghamton, Thomas J. Watson School of Engineering and Applied Science, Department of Mechanical Engineering, 2008. / Includes bibliographical references.

Thesis (Ph. D.)--State University of New York at Binghamton, Thomas J. Watson School of Engineering and Applied Science, Department of Systems Science and Industrial Engineering, 2008. / Includes bibliographical references.

Isotropic conductive adhesives (ICAs) have a growing range of applications in electronics packaging and have recently emerged as an important material in photo-voltaic module interconnections, particularly for thin-film and other non-silicon technologies where soldering processes are often unsuitable due to the nature of the metallisation or the limited maximum temperature the assembly can be exposed to. ICAs typically comprise of a high volume fraction of solid metallic flakes, usually silver, in an adhesive matrix because of its highly conductive oxide however, this thesis will focus on adhesives containing a large volume fraction of silver coated/metalised mono-sized polymer spheres (Ag-MPS). Incorporating silver coated mono-sized polymer spheres is anticipated to deliver specific advantages such as a significant reduction in the required silver content, improvement of the overall mechanical properties and flexibility to tune the properties of the filler according to the application compared with conventional flake filled adhesives. In this research advancements in the understanding of Ag-MPS filled ICAs, both through theory and experiments, have been made. Analytical models to predict an individual Ag-MPS resistance and Ag-MPS filled ICA resistance have been developed. The experiments based on the flat punch nanoindentation technique have been conducted to determine individual Ag-MPS resistances. The theoretical and experimental studies establish Ag-MPS diameter, coating resistivity, coating thickness, contact radius, and contact geometry as the main contributors towards the resistance of an Ag-MPS filled ICAs. These studies showed that Ag-MPS resistance decreases with increasing coating thickness and contact radius but increases with increasing coating resistivity. The experiments have also been conducted to investigate the effect of Ag-MPS volume fraction, diameter, coating thickness, curing conditions and shrinkage (affecting contact radius) on ICA conductivity and comparisons are made with flake filled and commercial ICAs. The results showed that ICA conductivity increases with increasing volume fraction and coating thickness but decreases with diameter. More importantly the results showed that conductivities similar to those of flake filled ICAs, including those commercially available, can be obtained using 70% less silver. The results show that, Ag content can be reduced further to just 7% with use of larger 30μm Ag-MPS but with a lower resulting conductivity. Thus for applications where very high conductivity is not required larger Ag-MPS may offer even greater potential cost benefits, which is something flake filled ICAs cannot offer. This is a significant achievement which can allow tuning of ICA formulations according to the demands of the application, which is not possible with the use of silver flakes as there is only a limited range of silver flake volume fractions that will yield useful levels of conductivity.

Due to the multi-tasking and miniaturization of electronic devices, faster heat transfer is required from the device to avoid the thermal failure. Die-attached polymer adhesives are used to bond the chips in electronic packaging. These adhesives have to hold strong mechanical, thermal, dielectric, and moisture resistant properties. As polymers are insulators, heat conductive particles are inserted in it to enhance the thermal flow with an attention that there would be no electrical conductivity as well as no reduction in dielectric strength. This thesis focuses on the characterization of polymer nanocomposites for thermal and electrical properties with experimental and computational tools. Platelet geometry of hexagonal boron nitride offers highly anisotropic properties. Therefore, their alignment and degree of orientation offers tunable properties in polymer nanocomposites for thermal, electrical, and mechanical properties. This thesis intends to model the anisotropic behavior of thermal and dielectric properties using finite element and molecular dynamics simulations as well as experimental validation.

No description available.

No description available.

As the microelectronic industry moves toward stacking of dies to achieve greater performance and smaller footprint, there are several reliability concerns when assembling the stacked dies on current organic substrates. These concerns include excessive warpage, interconnect cracking, die cracking, and others. Silicon interposers are being developed to assemble the stacked dies, and then the silicon interposers are assembled on organic substrates. Although such an approach could address stacked-die to interposer reliability concerns, there are still reliability concerns between the silicon interposer and the organic substrate. This work examines the use of diced glass panel as an interposer, as glass provides intermediate coefficient of thermal expansion between silicon and organics, good mechanical rigidity, large-area panel processing for low cost, planarity, and better electrical properties. However, glass is brittle and low in thermal conductivity, and there is very little work in existing literature to examine glass as a potential interposer material. Starting with a 150 x 150 mm glass panel with a thickness of 100 µm, this work has built alternating layers of dielectric and copper on both sides of the panel. The panels have gone through typical cleanroom processes such as lithography, electroplating, etc. Upon fabrication, the panels are diced into individual substrates of 25 x 25 mm and a 10 x 10 mm flip chip with a solder bump pitch of 75 um is then reflow attached to the glass substrate followed by underfill dispensing and curing. The warpage of the flip-chip assembly is measured. In parallel to the experiments, numerical models have been developed. These models account for viscoplastic behavior of the solder. The models also mimic material addition and etching through element “birth-and-death” approach. The warpage from the models has been compared against experimental measurements for glass substrates with flip chip assembly. It is seen that the glass substrates provide significantly lower warpage compared to organic substrates, and thus could be a potential candidate for future 3D systems.