Fiber-optic Fabry-Perot interferometric (FFPI) sensors have been widely used due to their high sensitivity, ease of fabrication, miniature size, and capability for multiplexing. However, direct measurement of self-assembled thin films, receptor immobilization process or biological reaction is limited in the FFPI technique due to the difficulty of forming Fabry-Perot cavities by the thin film itself. Novel methods are needed to provide an accurate and reliable measurement for monitoring the thin-film growth in the nanometer range and under various conditions. In this work, two types of fiber-optic multicavity Fabry-Perot interferometric (MFPI) sensors with built-in temperature compensation were designed and fabricated for thin-film measurement, with applications in chemical and biological sensing. Both the tubing-based MFPI sensor and microgap MFPI sensor provide simple, yet high performance solutions for thin-film sensing. The temperature dependence of the sensing cavity is compensated by extracting the temperature information from a second multiplexed cavity. This provides the opportunity to examine the thin-film characteristics under different environment temperatures. To demonstrate the potential of this structure for practical applications, immunosensors were fabricated and tested using these structures. Self-assembled polyelectrolytes served as a precursor film for immobilization of antibodies to ensure they retain their biological activity. This not only provides a convenient method for protein immobilization but also presents the possibility of increasing the binding capacity and sensitivity by incorporating multilayers of antibodies into polyelectrolyte layers. The steady-state measurement demonstrated the surface concentration and binding ratio of the immunoreaction. Analysis of the kinetic binding profile provided a fast and effective way to measure antigen concentration. Monitoring the immunoreaction between commercially available immunoglobulin G (IgG) and anti-IgG demonstrated the feasibility of using the MFPI sensing system for immunosensing applications. / Ph. D.

The conventional way of using a nonlinear Fabry-Perot cavity as an optical memory requires a negative pulse input to reset the state of the cavity. The possibility of using positive pulses to turn a system of nonlinear Fabry-Perot cavities on and off is studied and it was found that positive pulse switching is possible in a system of two coupled nonlinear cavities. First, Korpel and Lohmann's proposal of using polarization switching in a single nonlinear birefringent cavity was studied. After a detailed investigation of their proposal it was found that positive pulse switching in a single nonlinear Fabry-Perot cavity is not possible. One of the reasons is that the eigen-polarization states of the output of a nonlinear Fabry-Perot cavity cannot be switched independently. Although it is not possible to switch a single nonlinear Fabry-Perot cavity with positive pulses we were able to use the coupling of the eigen-polarization states to implement other kinds of optical switches which were demonstrated experimentally. The cross-talk effect in a metallic Fabry-Perot cavity was also studied. Next, a steady state model of a system of two coupled nonlinear Fabry-Perot cavities was developed and it was found that positive pulse switching is possible in such a system. The output can be turned on and off either by pulses sent into different cavities or by pulses of different magnitudes sent into one cavity. Finally, the dynamic behavior of the coupled cavities system was modeled by extending Goldstone and Garmire's model of a single cavity with one input to a system of two coupled cavities with two inputs. We verified by numerical calculations that positive pulse switching is also possible in the dynamic regime. / Ph. D.

The electrostatic self-assembly (ESA) method presents an effective application in the field of biosensing due to the uniform nanoscale structure. In previous research, a single mode fiber (SMF) sensor system had been investigated for the thin-film measurement due to the high fringe visibility. However, compared with a SMF sensor system, a multimode fiber (MMF) sensor system is lower-cost and has larger sensing area (the fiber core), providing the potential for higher sensing efficiency. In this thesis, a multimode fiber-optic sensor has been developed based on extrinsic Fabry-Perot interferometry (EFPI) for the measurement of optical thickness in self-assembled thin film layers as well as for the immunosensing test. The sensor was fabricated by connecting a multimode fiber (MMF) and a silica wafer. A Fabry-Perot cavity was formed by the reflections from the two interfaces of the wafer. The negatively charged silica wafer could be used as the substrate for the thin film immobilization scheme. The sensor is incorporated into the white-light interferometric system. By monitoring the optical cavity length increment, the self-assembled thin film thickness was measured; the immunoreaction between immunoglobulin G (IgG) and anti-IgG was investigated. / Master of Science

Elevators are a necessary component of the modern urban and suburban life. The guide rails the car and counterweight move on are the most sensitive parts when it comes to de-habilitating damage that can be caused by an earthquake. Conventional sensors are becoming obsolete in sensing for today's multistory buildings because they don't monitor the structural health of the guide rails. This sensing task falls into the fiber sensing niche market because of a fiber sensor's ability to be multiplexed. Previous work by Taplin and Jackson showed demodulation of the interference spectrum of two Fabry-Perot cavities using Fourier analysis. The goal of this research is to use Fourier analysis to demodulate the spectrum of four multiplexed extrinsic Fabry-Perot fiber interferometers for strain measurements. Comparisons of fiber, foil, and theoretical strains are made. Also, experiments showing the system's air-gap stability and crosstalk are provided. / Master of Science

The developing field of smart structures and skins provides an application to which fiber optic sensors bring unique capabilities and benefits. The primary cost in a network of fiber sensors is in the sources, receivers and associated hardware and can be prohibitive for a large number of sensors. Multiplexing of sensors based on spread spectrum techniques offers an efficient and cost effective solution to this limitation. The system hardware developed in this research work is capable of the real time monitoring of a four sensor network. Experimental results with embedded and attached Extrinsic Fabry Perot Interferometers (EFPI) are presented. The system can be used to multiplex any type of sensor which translates the measurand into intensity variations of the light. A measure of the system efficiency is obtained using crosstalk measurements. A suppression of 40 dB has been obtained between the desired sensor signal and the interference. The effect on system performance has been observed by varying system parameters such as code length and separation between codes. Highly sensitive embedded interferometric sensors have been used in a multimeasurand environment to measure temperature and strain. A solution to the inherent 'near-far' problem in an optical COMA system has been proposed and results for the same are presented. A novel WDM/CDM hybrid (Wavelength Division Multiplexing/Code Dhtision Multiplexing) scheme has been proposed to increase the light intensity at the detector thereby increasing the number of sensors in the system. Methods to optimize and upgrade the system are discussed. / Master of Science

The detection and active monitoring of hydrogen gas levels is essential in many areas of industry including manufacturing, storage, and transport of this gas. Previously, methods used to detect hydrogen gas have relied upon monolithic technologies to create resistive-based sensors which are impractical for many applications requiring electrical isolation or operation in the presence of strong electromagnetic fields. Materials can be sputter deposited along cylindrical optical fiber-based sensors to create novel fiber-optic chemical sensors. Herein, the mechanisms allowing the detection of hydrogen gas using a modified Extrinsic Fabry-Perot Interferometric (EFPI) sensor are presented in this work. A new custom-designed, custom-built radio frequency (RF) magnetron sputtering system has been used to deposit thin films of palladium metal along with cylindrical substrates. The surface morphology of the deposited films are investigated using a variety of analytical tools, including Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (AES), and Auger Electron Spectroscopy (AES). The system is used to deposit thin films of palladium along a cylindrical EFPI fiber-optic sensor to produce a new fiber-optic hydrogen gas sensor. Experimental results obtained in a controlled hydrogen atmosphere are used to demonstrate the high resolution and fast response time associated with these new hybrid sensors. / Master of Science

Conventional fiber optic interferometric sensors employing a monochromatic source prove to be inadequate for applications requiring absolute, real-time value of magnitude and direction of the applied perturbation. This limitation can be overcome by using a broadband light source to extract unambiguous information from the sensor in the wavelength domain. Several variations in the signal processing techniques for white light interferometry are discussed and compared in terms of resolution, bandwidth and cost. A detailed analysis is made of the principle of operation and basic features of the commercially available absolute sensing system. This compact system is self calibrating, has a 100 micro-strain Ole) strain and 2°C temperature resolution and is ideal for applications in environments where the parameter to be measured is static or quasi-static. High finesse Fabry-Perot cavities are employed to obtain almost an order of magnitude sensitivity improvement over conventional low finesse cavities. The principle of white light interferometry is extended to absolute axial stain and temperature sensing in two-mode, elliptical-core fibers. Other novel applications, such as to operation of photo induced refractive index gratings and fiber characterization are proposed. / Master of Science

The use of optical sensors to perform health monitoring in fault-tolerant multicomputers can allow the multicomputer to detect imminent failure in a particular section of the interconnection network due to damaging strain. This detection method allows the rerouting of critical data before data link failure occurs. This thesis investigates the implementation of the extrinsic Fabry-Perot interferometer into an optical hybrid communications/sensing network. A testbed of personal computers, acting as nodes of a multicomputer, are used to monitor the integrity of the network to a high degree of accuracy. When a node determines that an adjacent data link is no longer reliable due to physical damage, communications are rerouted and the node is shut down. Results of experiments with the testbed have shown that redundant nodes can be used to share computational loads, increasing the performance of the multicomputer, until network failure forces redundant nodes to assume full responsibility for computational tasks. Multicomputer performance suffers as a result of network damage, but full functionality is retained with no occurrence of errors or unknown conditions due to data link failure. / Master of Science

Since the invention of Laser (in 1960) and low loss optical fiber (in 1966) [1], extensive research in fiber-optic sensing technology has made it a well-defined and matured field [1]. The measurement of physical parameters (such as temperature and pressure) in extremely harsh environment is one of the most intriguing challenges of this field, and is highly valued in the automobile industry, aerospace research, industrial process monitoring, etc. [2]. Although the semiconductor based sensors can operate at around 500oC, sapphire fiber sensors were demonstrated at even higher temperatures [3]. In this research, a novel sensor structure is proposed that can measure both pressure and temperature simultaneously. This work effort consists of design, fabrication, calibration, and laboratory testing of a novel structured temperature compensated pressure sensor. The aim of this research is to demonstrate an accurate temperature measurement, and pressure measurement using a composite Fabry-Perot interferometer. One interferometer measures the temperature and the other accurately measures pressure after temperature compensation using the temperature data from the first sensor. / Master of Science

Several techniques for measuring humidity are presented. The goal of the study is to use the electrostatic self-assembled monolayer synthesis process to fabricate a Fabry-Parot Cavity based optical fiber humidity sensor. The sensing scheme bases on the refractive index change with relative humidity of the film applied to the end of optical fiber. That is, the change in reflected optical power indicates certain humidity. To achieve this, some chemicals induce on specific coating materials were applied at the end of optical fiber. In this thesis, experimental results are given to prove that the humidity sensor has high sensitive and fast response time. Furthermore, we investigate the potential for the use of human breathing monitoring and air flow rate detection. Results from preliminary tests of each are given. / Master of Science