Graphene is a promising material for flexible electronics due to its extraordinary electrical, mechanical, and optical properties. One of the biggest challenges today is to transfer large-scale graphene sheet to flexible substrates with minimal quality degradation. In this thesis, a bilayer polymer support for graphene transfer is proposed. Liquid PDMS (polydimethylsiloxane) is first coated on graphene to conform to its surface morphology. A flexible plastic substrate is then pressed on PDMS as a durable support. After PDMS is cured, electrochemical delamination is used to separate graphene from the copper foil. Due to the extremely low work of adhesion between graphene and PDMS, the graphene film on PDMS can be further transferred onto silicon wafer or other flexible substrates by simple adhesion. An added benefit of the PDMS layer is its strain isolation effect, which could protect graphene-based devices from breaking under external loads applied on the flexible substrate. The strain isolation effect of PDMS is verified with an analytical model and finite element analysis. The design of a prototype roll-to-roll graphene transfer machine is also presented. / text

Nanoscale materials enable unique opportunities at the interface between physical and life sciences. The interface between nanoelectronic devices and biological systems makes possible communication between these two diverse systems at the length scale relevant to biological functions. The development of a bottom-up paradigm allows the nanoelectronic units to be synthesized and patterned on unconventional substrates. In this thesis, I will focus on the development of three-dimensional (3D) nanoelectronics, which mimics the structure of porous biomaterials to explore new methods for seamless integration of electronics with other materials, with a special focus on biological tissue. / Chemistry and Chemical Biology

Indium-Gallium-Zinc-Oxide (a-IGZO) is an amorphous oxide semiconductor that has been attracting increasing attention for use in flat panel display and optoelectronic applications. This is largely due to IGZO’s high mobility at low processing temperatures. In this thesis, IGZO films were successfully grown on polyethylene naphthalate (PEN) substrates by RF magnetron sputtering at room temperature. These films were flexible, transparent and had a good Hall mobility (5-12 cm2/Vs). High quality metal oxide Schottky contacts were fabricated on these as-grown IGZO/PEN films with on-off rectification ratios of up to 108. These were then used as the gate contacts in transparent metal semiconductor field effect transistors (MESFETs). The performance and device stability of these IGZO/PEN MESFETs were investigated via a series of stress tests in both dark conditions and under illumination at different wavelengths in the visible spectrum. During constant voltage stress testing under illumination, the threshold voltage shifted by -0.54 V and 0.38 V for negative and positive gate biasing, respectively. These shifts proved reversible when devices were left in dark conditions for extended periods of time. The effect of persistent photoconductivity after exposure to different illumination sources was examined, with three potential passivation coatings to reduce this unwanted effect explored. Transparent IGZO/PEN MESFETs with an absolute transmission of up to 75% were achieved with the use of ITO ohmic contacts. These devices survived mechanical bending down to a radius of 7 mm with negligible variation in on-current and threshold voltage. This allows for the possibility of incorporating their use in future applications such as flexible transparent electronics.

Today’s information-centered world leads the ever-increasing consumer demand for more powerful, multifunctional portable devices. Additionally, recent developments on long-lasting energy sources and compliant, flexible systems, have introduced new required features to the portable devices industry. For example, wireless sensor networks are in urgent need of self-sustainable, easy-to-deploy, mobile platforms, wirelessly interconnected and accessible through a cloud computing system. The objective of my doctoral work is to develop integration strategies to effectively fabricate mechanically flexible, energy-independent systems, which could empower sensor networks for a great variety of new exciting applications. The first module, flexible electronics, can be achieved through several techniques and materials. Our main focus is to bring mechanical flexibility to the state-of-the-art high performing silicon-based electronics, with billions of ultra-low power, nano-sized transistors. Therefore, we have developed a low-cost batch fabrication process to transform standard, rigid, mono-crystalline silicon (100) wafer with devices, into a thin (5-20 m), mechanically flexible, optically semi-transparent silicon fabric. Recycling of the remaining wafer is possible, enabling generation of multiple fabrics to ensure lowcost and optimal utilization of the whole substrate. We have shown mono, amorphous and poly-crystalline silicon and silicon dioxide fabrics, featuring industry’s most advanced high-/metal-gate based capacitors and transistors. The second module consists on the development of efficient energy scavenging systems. First, we have identified an innovative and relatively young technology, which can address at the same time two of the main concerns of human kind: water and energy. Microbial fuel cells (MFC) are capable of producing energy out the metabolism of bacteria while treating wastewater. We have developed two micro-liter MFC designs, one with carbon nanotubes (CNT)-based anode and the second with a more sustainable design and easy to implement. Power production ranges from 392 to 100 mW/m3 depending on design. Additionally we have explored a flexible thermoelectric generator (0.139 μW/cm2) and a lithium-ion battery (~800 μAh/m2) for back-up energy generation and storage. Future work includes the implementation of a self-powered System-on-Package which gathers together energy generation, storage and consumption. Additionally we are working to demonstrate Complementary Metal-Oxide-Semiconductor (CMOS) circuitry on our flexible platform, as well as memory systems.

Gravure printing is a conventional printing process used for printing graphics on products ranging from magazines and packaging to wallpaper and floor coverings. It is a versatile process that can be used to deposit a variety of fluid materials onto many different surfaces. It is also capable of very high speed deposition, with speeds up to 60 m/min being reported. Because of its versatility and high throughput capability, gravure is an attractive platform for the manufacture of devices composed of relatively thin layers of functional, electronic materials deposited onto flexible substrates. In many cases, these materials can be deposited in liquid form, in which case gravure printing can potentially be used. One such material that is commonly used is Indium Tin Oxide (ITO), a transparent, conducting ceramic material. It is commonly deposited onto flexible, transparent polyethylene terapthalate (PET) films that can be used in flexible displays, solar cells, and other devices requiring a transparent, conducting layer. This thesis examines the effect of key process parameters on the physical and functional characteristics of a printed ITO nanoparticle layer. ITO layers were successfully printed that were between 300 and 1300 nm thick, with roughness Ra generally less than a few hundred nm. The sheet resistance values were relatively high, in the hundreds of kohms/square. The transparency was relatively low, although the films were generally transparent. Several parameters were found to be significant in affecting the several different physical and performance measures, specifically solvent and ITO content, as well as cell geometry.

abstract: The field of flexible displays and electronics gained a big momentum within the recent years due to their ruggedness, thinness, and flexibility as well as low cost large area manufacturability. Amorphous silicon has been the dominant material used in the thin film transistor industry which could only utilize it as N type thin film transistors (TFT). Amorphous silicon is an unstable material for low temperature manufacturing process and having only one kind of transistor means high power consumption for circuit operations. This thesis covers the three major researches done on flexible TFTs and flexible electronic circuits. First the characterization of both amorphous silicon TFTs and newly emerging mixed oxide TFTs were performed and the stability of these two materials is compared. During the research, both TFTs were stress tested under various biasing conditions and the threshold voltage was extracted to observe the shift in the threshold which shows the degradation of the material. Secondly, the design of the first flexible CMOS TFTs and CMOS gates were covered. The circuits were built using both inorganic and organic components (for nMOS and pMOS transistors respectively) and functionality tests were performed on basic gates like inverter, NAND and NOR gates and the working results are documented. Thirdly, a novel large area sensor structure is demonstrated under the Electronic Textile project section. This project is based on the concept that all the flexible electronics are flexible in only one direction and can not be used for conforming irregular shaped objects or create an electronic cloth for various applications like display or sensing. A laser detector sensor array is designed for proof of concept and is laid in strips that can be cut after manufacturing and weaved to each other to create a real flexible electronic textile. The circuit designed uses a unique architecture that pushes the data in a single line and reads the data from the same line and compares the signal to the original state to determine a sensor excitation. This architecture enables 2 dimensional addressing through an external controller while eliminating the need for 2 dimensional active matrix style electrical connections between the fibers. / Dissertation/Thesis / Ph.D. Electrical Engineering 2012

abstract: Optical Fibers coupled to laser light sources, and Light Emitting Diodes are the two classes of technologies used for optogenetic experiments. Arizona State University's Flexible Display Center fabricates novel flexible Organic Light Emitting Diodes(OLEDs). These OLEDs have the capability of being monolithically fabricated over flexible, transparent plastic substrates and having power efficient ways of addressing high density arrays of LEDs. This thesis critically evaluates the technology by identifying the key advantages, current limitations and experimentally assessing the technology in in-vivo and in-vitro animal models. For in-vivo testing, the emitted light from a flat OLED panel was directly used to stimulate the neo-cortex in the M1 region of transgenic mice expressing ChR2 (B6.Cg-Tg (Thy1-ChR2/EYFP) 9Gfng/J). An alternative stimulation paradigm using a collimating optical system coupled with an optical fiber was used for stimulating neurons in layer 5 of the motor cortex in the same transgenic mice. EMG activity was recorded from the contralateral vastus lateralis muscles. In vitro testing of the OLEDs was done in primary cortical neurons in culture transfected with blue light sensitive ChR2. The neurons were cultured on a microelectrode array for taking neuronal recordings. / Dissertation/Thesis / ICMS response in front and hind limb / Optogenetic response using iLEDs and OLEDs / iLED vs iLED coupled to optical fiber response / Masters Thesis Bioengineering 2015

abstract: The work presented in this manuscript has the overarching theme of radiation. The two forms of radiation of interest are neutrons, i.e. nuclear, and electric fields. The ability to detect such forms of radiation have significant security implications that could also be extended to very practical industrial applications. The goal is therefore to detect, and even image, such radiation sources. The method to do so revolved around the concept of building large-area sensor arrays. By covering a large area, we can increase the probability of detection and gather more data to build a more complete and clearer view of the environment. Large-area circuitry can be achieved cost-effectively by leveraging the thin-film transistor process of the display industry. With production of displays increasing with the explosion of mobile devices and continued growth in sales of flat panel monitors and television, the cost to build a unit continues to decrease. Using a thin-film process also allows for flexible electronics, which could be taken advantage of in-house at the Flexible Electronics and Display Center. Flexible electronics implies new form factors and applications that would not otherwise be possible with their single crystal counterparts. To be able to effectively use thin-film technology, novel ways of overcoming the drawbacks of the thin-film process, namely the lower performance scale. The two deliverable devices that underwent development are a preamplifier used in an active pixel sensor for neutron detection and a passive electric field imaging array. This thesis will cover the theory and process behind realizing these devices. / Dissertation/Thesis / Masters Thesis Electrical Engineering 2015

This thesis presents the development of chemical vapour deposited (CVD) graphene and multi-walled carbon nanotubes (MWCNTs) as enabling technologies for flexible transparent conductors offering enhanced functionality. The technologies developed could be employed as thin film field emission sources, optical sensors and substrate-free wideband optical polarisers. Detailed studies were performed on CVD Fe and Ni catalysed carbon nanotubes and nanofibres on indium tin oxide, aluminium and alumina diffusion barriers. Activations energies of 0.5 and 1.5 eV were extracted supporting surface diffusion limited catalysis forCNTs and CNFs. For the first time an activation energy of 2.4 eV has been determined for Cu-catalysed growth of CVD graphene. Graphene was shown to deviate significantly from the more traditional rate-limited surface diffusion and suggests carbon-atom-lattice integration limited catalysis. An aligned dry-transferred MWCNT thin film fabrication technique was developed using MWCNTs of varied lengths to control the optical transparency and conductivity. A process based on the hot-press lamination of bilayer CVD graphene (HPLG) was also developed. Transport studies revealed that these thin films behave, in a macroscopic sense, similar to traditional c-axis conductive graphite and deviate toward tunnel dominated conduction with increasing degrees of network disorder. Various MWCNT-based thin film field emitters were considered. Solution processing was shown to augment the surface work function of the MWCNTs resulting in reduced turn-on electric fields. Integrated zinc oxide nanowires were investigated and were shown to ballast the emission, thereby preventing tip burn out, and offered lower than expected turn-on fields due to the excitation of a hot electron population. To obviate nearest neighbour electrostatic shielding effects an electrochemical catalyst activation procedure was developed to directly deposit highly aligned sparse carbon nanofibres on stainless steel mesh. Highly-aligned free-standing MWCNT membranes were fabricated through a solid-state peeling technique. Membranes were spanned across large distances thereby offering an ideal platform to investigate the unambiguous photoresponse of MWCNTs by removing all extraneous substrate interfaces, charge traps and nanotube-electrode Shottky barriers as well as using pure, chemically untreated material. Oxygen physisorbtion was repeatedly implicated through in-situ lasing and in-situ heated EDX measurements, FT-IR and low temperature transport and transfer measurements. A MWCNT membrane absorptive polariser was fabricated. Polarisers showed wideband operation from 400 nm to 1.1 μm and offered operation over greater spectral windows than commercially available polymer and glass-support dichroic films. Ab-initio simulations showed excellent agreement with the measured polarisation attributing the effect to long-axis selective absorption.

abstract: Technological advances in low power wearable electronics and energy optimization techniques make motion energy harvesting a viable energy source. However, it has not been widely adopted due to bulky energy harvester designs that are uncomfortable to wear. This work addresses this problem by analyzing the feasibility of powering low wearable power devices using piezoelectric energy generated at the human knee. We start with a novel mathematical model for estimating the power generated from human knee joint movements. This thesis’s major contribution is to analyze the feasibility of human motion energy harvesting and validating this analytical model using a commercially available piezoelectric module. To this end, we implemented an experimental setup that replicates a human knee. Then, we performed experiments at different excitation frequencies and amplitudes with two commercially available Macro Fiber Composite (MFC) modules. These experimental results are used to validate the analytical model and predict the energy harvested as a function of the number of steps taken in a day. The model estimates that 13μWcan be generated on an average while walking with a 4.8% modeling error. The obtained results show that piezoelectricity is indeed a viable approach for powering low-power wearable devices. / Dissertation/Thesis / Masters Thesis Electrical Engineering 2020