L'avancée de la technologie des PRF a suscité l'intérêt de l'introduction de nouvelles fibres, comme la fibre de basalte, qui a un potentiel d'offrir une solution efficace, lorsqu’utilisée dans les structures en béton, soit sur la résistance à la corrosion, la durabilité et la rentabilité. En outre, les codes et les guides disponibles, ne fournissent pas de recommandations pour l'utilisation de barres en PRFB puisque les recherches passées dans ce domaine sont limitées. Donc, des travaux de recherche sont nécessaires pour caractériser et comprendre le comportement des barres de PRFB dans les éléments en béton armé. En conséquence, les objectifs principaux sont d'évaluer les caractéristiques à court et long terme des barres de PRFB nouvellement développées, ainsi que d'évaluer les performances structurales de ces nouvelles barres comme renforcement interne dans les poutres et les dalles de pont et d'introduire ce nouveau renforcement dans les codes et les guides de dimensionnement. Les tests expérimentaux ont été faits en trois parties. La première partie porte sur le développement de trois nouvelles barres et tendons en PRFB pour déterminer leurs propriétés physiques et mécaniques. Les performances à long terme et de durabilité ont été réalisées en conditionnant les barres de PRFB dans une solution alcaline simulant les conditions humides dans le béton pour déterminer la compatibilité comme renforcement interne dans les éléments en béton. Par la suite, les propriétés ont été déterminées et comparées avec des spécimens non conditionnés (référence). La seconde partie a porté sur sept dalles de pont en béton armé grandeur réelle avec les bords restreints, simulant les tabliers de pont les plus utilisés en Amérique du Nord, pour évaluer la performance des dalles renforcées de PRFB et d'acier. Les dalles mesurent 3000 mm de long × 2500 mm de large × 200 mm d'épaisseur. Les dalles ont été testées jusqu'à la rupture sous une charge concentrée au centre de celles-ci simulant l'empreinte d'une roue d'un camion. Les capacités en poinçonnement sont prédites en utilisant les exigences réglementaires disponibles, et sont comparées aux résultats expérimentaux. La troisième partie de cette étude portait sur les essais de 14 poutres en béton de 3100 mm de long × 200 mm de large × 300 mm de profond pour examiner le comportement en flexion et les performances en service des barres de PRFB avec deux états de surfaces: fini sablé et crénelé. Les poutres ont été testées en flexion en quatre points avec une portée libre de 2700 mm jusqu'à la rupture. Les résultats sont introduits et discutés en terme : du comportement de la fissuration, des flèches, de la capacité en flexion et des modes de ruptures. De plus, le coefficient d'adhérence (kb) des barres de PRFB est déterminé et comparé avec les recommandations des codes et guides actuels. Les résultats sont introduits et discutés en terme : du comportement de la fissuration, des flèches, de la capacité en flexion et des modes de ruptures. De plus, le coefficient d'adhérence des barres de PRFB est déterminé et comparé avec les recommandations des codes et guides actuels. Les résultats de l'étude concluent sur la viables pour la production des barres de PRFB pour respecter les exigences des codes actuelles. Également, les résultats d'essai indiquent que les barres de PRFB ont de bonnes propriétés mécaniques et peuvent être placées dans la même catégorie que les barres de PRFV, soit grade III. De plus, le comportement des poutres et des dalles de pont renforcées de PRFB est similaire que pour un renforcement en PRFV et PRFC et les exigences réglementaires sont applicables pour les barres de PRFB. / Abstract: The advances in fiber-reinforced-polymer (FRP) technology have spurred interest in introducing new fibers, such as basalt FRP (BFRP), which has the potential to offer an efficient solution when implemented in concrete structure, such as corrosion resistant, durable and cost-effective. Furthermore, the available design codes and guides do not provide any recommendations for the use of BFRP bars since fundamental studies and relevant applications are still limited. Therefore, investigations are needed to characterize and understand the behavior of BFRP bars in concrete members. Consequently, the main objectives of this experimental investigation are to evaluate the short- and long-term characteristics of newly developed BFRP bars, as well as evaluate the structural performance of these new bars as internal reinforcement for concrete beams and bridge-deck slabs to introduce these new reinforcing bars to the design codes and guides. The experimental tests were completed through three parts. The first part was conducted on three newly developed BFRP bars and tendons to investigate their physical and mechanical properties. Durability and long-term performance were assessed by conditioning the BFRP bars in an alkaline solution simulating the moist concrete environment to determine their suitability as internal reinforcement for concrete elements. Thereafter, the properties were assessed and compared with the unconditioned (reference) values. The second part of this study was conducted on seven full-scale edge-restrained concrete bridge-deck slabs simulating actual slab-on-girder bridge-deck that is commonly used in North America to evaluate the performance of concrete bridge-deck slabs reinforced with BFRP and steel bars. The deck slabs measured 3000 mm long × 2500 mm wide × 200 mm deep. The slabs were tested up to failure under single concentrated load acting on the center of each slab simulating the footprint of sustained truck wheel load. The punching shear capacities were predicted using the available provisions, and compared with the experimental results. The third part of this study included testing of fourteen concrete beams of 3100 mm long × 200 mm wide × 300 mm deep to investigate the flexural behavior and serviceability performance of sand-coated and ribbed BFRP bars in concrete beams. The beams were tested under four-point bending over a clear span of 2700 mm until failure. The results are introduced and discussed in terms of cracking behavior, deflection, flexure capacity, and failure modes. In addition, the bond-dependent coefficient (kb) of the BFRP bars was determined and compared with the recommendations of the current FRP design codes and guides. The findings of this study concluded the feasibility of producing BFRP bars meet the requirements of the current FRP standards. Also, the test results revealed that the BFRP bars had good mechanical behavior and could be placed in the same category as grade II and grade III GFRP bars. Moreover, the behavior of the concrete bridge-deck slabs and beams reinforced with BFRP bars was quite similar to the counterparts reinforced with glass- and carbon-FRP bars and the available FRP provisions are applicable for BFRP bars. The beam test results yielded an average bond-dependent coefficient (kb) of 0.76±0.03 and 0.83±0.03 for the sand-coated and ribbed BFRP bars, respectively.

This thesis is intended to identify the mode I and mode II fracture toughness to characterize the thin laminate interface by using the Double Cantilever Beam test (DCB) and End Notched Flexure test (ENF). This study’s thin laminate was Polyethylene Terephthalate and Low-Density Polyethylene (PET-LDPE), which is mostly used by packaging industries in the manufacturing of packages to store liquid food. As PET-LDPE film is very flexible and difficult to handle, DCB and ENF tests cannot be performed directly so, sheet metal (Aluminium) was used as carrier material. PET-LDPE film is placed between two aluminum plates to reduce the flexibility and perform the tests. Therefore, the Aluminium plate was also studied to find the constitutive parameters (young’s modulus (E) and mixed hardening parameters (Plastic properties)) under the tensile test and three-point bending test. From the test response, energy release rate calculation has been done for different Pre-crack lengths to validate the DCB and ENF experimental setup, study the different Pre-crack lengths, and characterize the laminate interface. Finite Element simulation (FE simulation) for those tests were carried out in AbaqusTM2020. When needed, the force versus displacement response from FE simulation was optimized against experimental response to find the required constitutive parameters (Young’s modulus, Hardening parameters, and PET-LDPE material properties). Implementing of optimization algorithm and automated simulation has been done with the help of MATLAB code. In contrast, MATLAB works as a server, and Abaqus works as a client and connected two interfaces to run the optimization. The results obtained from experiments and FE simulations were compared to the results found in the literature.

The thesis summarises information about recycled aggregates and basalt fibres, their interaction in composite material such as concrete. It focuses on the potential deficiencies and properties of concrete due to the use of recycled aggregates and on the possibilities of their subsequent elimination of their negative impact by the use of basalt fibres. It characterizes individual raw materials and their interaction in concrete. It includes verification of the properties of the individual sub-components and the resulting concrete itself. An assessment is made of the impact of the use of recycled aggregates on the properties of concrete (compresive strength, static modulus of elasticity, residual flexure tensile strength and others). The thesis discusses the question of whether the same or similar mechanical properties of concrete can be achieved with natural and recycled aggregates using basalt reinforcing fibres. The work provides for the possibility of settlement the values of these concrete parameters by using basalt fibres as a dispersed reinforcement in concrete. The recycled aggregates come from concrete company JARO AS in the north of Norway, where this work was conducted with the financial support from Erasmus+ at The Arctic University of Norway - campus Narvik.

This master’s thesis describes an experimental program investigating the strengthening of beams of glued laminated timber with composite reinforcement. The work compares the behavior of beams reinforced with composite reinforcement with unreinforced beam and with solid timber beam. The work also deals with identifying and evaluating the physic-mechanical properties of materials.

Preplaced aggregate concrete (PAC) is produced by grouting high workability cement based grouts among the voids of compacted coarse aggregate mass. Because of its low shrinkage, PAC has been used for many repair jobs like; tunnel lines, dams and bridge piers. Moreover, it has been used for underwater construction. Grout has a major effect on the properties of produced PAC and well defined grout controls the properties of resulted PAC. The effect of types and amount of powder materials, admixtures, sand and water content on the properties of fresh and hardened grout for the production of PAC have been investigated. Tests on hardened grout and PAC properties have also been carried out to investigate the most important effects. A correlation between hardened properties of grout and PAC has also been analyzed. Grout rheology using four different gradation sands at two different cement-sand and at different w/c ratios ratios has been identified experimentally; no added chemical admixtures or mineral additives had first employed, then superplasticizer (SP) was added at 2% and 1%, and finally a combination of 1% SP and pulverized fuel ash (Pfa) at 20% of the cement weight was employed for all mixes. Grout tests have included two point workability tests by the Viskomat NT, flow time funnel test, Colcrete flow meter test, and water bleeding test. After that, eighteen grout mixes with high workability were produced using three different sands at three w/c ratios and two c/s ratios with 1% SP and Pfa at 20% of the cement weight were designed. Eighteen hardened grout and PAC then produced and their compressive strength and sorptivity were tested. Grout rheology can be defined by the rheology of cement paste employed and the internal distance between sand particles. The effect of sand surface texture on grout rheology is important at very low internal distances. Fresh grout yield stress is the most important property which gives the same degree of sensitivity for all grouts regardless the material type and content used in the mix. There are strong relations between compressive strength of grout and PAC, but less correlation between them in sorptivity test because of the effect high quantity of coarse aggregate of PAC. Sorptivity of PAC is low comparing with different kinds of concrete suggesting its advantage for underwater construction. / Libyan High Education Ministry

No description available.

No description available.

Reinforced concrete (RC) structures constitute a significant portion of the building inventory in earthquake-prone regions of the United States. Accurate analysis tools are necessary to allow the quantitative assessment of the performance and safety offered by RC structures. Currently available analytical approaches are not deemed adequate, because they either rely on overly simplified models or are restricted to monotonic loading. The present study is aimed to establish analytical tools for the accurate simulation of RC structures under earthquake loads. The tools are also applicable to the simulation of reinforced masonry (RM) structures. A new material model is formulated for concrete under multiaxial, cyclic loading conditions. An elastoplastic formulation, with a non-associative flow rule to capture compression-dominated response, is combined with a rotating smeared-crack model to capture the damage associated with tensile cracking. The proposed model resolves issues which characterize existing concrete material laws. Specifically, the newly proposed formulation accurately describes the crack opening/closing behavior and the effect of confinement on the strength and ductility under compressive stress states. The model formulation is validated with analyses both at the material level and at the component level. Parametric analyses on RC columns subjected to quasi-static cyclic loading are presented to demonstrate the need to regularize the softening laws due to the spurious mesh size effect and the importance of accounting for the increased ductility in confined concrete. The impact of the shape of the yield surface on the results is also investigated. Subsequently, a three-dimensional analysis framework, based on the explicit finite element method, is presented for the simulation of RC and RM components under cyclic static and dynamic loading. The triaxial constitutive model for concrete is combined with a material model for reinforcing steel which can account for the material hysteretic response and for rupture due to low-cycle fatigue. The reinforcing steel bars are represented with geometrically nonlinear beam elements to explicitly account for buckling of the reinforcement. The strain penetration effect is also accounted for in the models. The modeling scheme is validated with the results of experimental static and dynamic tests on RC columns and RC/RM walls. The analyses are supplemented with a sensitivity study and with calibration guidelines for the proposed modeling scheme. Given the computational cost and complexity of three-dimensional finite element models in the simulation of shear-dominated structures, the development of a conceptually simpler and computationally more efficient method is also pursued. Specifically, the nonlinear truss analogy is employed to capture the response of shear-dominated RC columns and RM walls subjected to cyclic loading. A step-by-step procedure to establish the truss geometry is described. The uniaxial material laws for the concrete and masonry are calibrated to account for the contribution of aggregate interlock resistance across inclined shear cracks. Validation analyses are presented, for quasi-static and dynamic tests on RC columns and RM walls. / Ph. D.

Le dimensionnement des joints collés est une préoccupation majeure du CNES pour lesapplications spatiales des futurs lanceurs. Pour dimensionner une structure collée, il est nécessaire depouvoir apprécier les caractéristiques mécaniques du joint collé.Dans cette étude, trois adhésifs structuraux ont été sélectionnés (Hysol®EA 9321, Hysol®EA9394 et Hysol EA® 9395). Après leur caractérisation massique, une étude statistique pour mettre enévidence les effets des différents paramètres (vitesse d’essai, géométrie éprouvette, le degré depolymérisation…) a été entreprise.La deuxième étape a pour objectif de fiabiliser l’analyse des essais de fissuration etd’améliorer la compréhension des mécanismes d’endommagement et de propagation de fissure dansles liaisons collées. Trois types d’essai ont été utilisés, à savoir, l’essai Double Cantilever Beam(DCB), pour l’étude du mode I, l’essai End Notched Flexure (ENF), pour le mode II, et l’essai MixedMode Bending (MMB), pour les chargements en mode mixte I/II. Nous avons développé de nouvellesinstrumentations et méthodologies d’analyse. Pour affiner le protocole de test standard, la techniquedite de « backface strain monitoring » a été utilisée. Elle consiste à positionnées des jauges dedéformation sur les surfaces de l’éprouvette de façon à enregistrer l’évolution du signalextensométrique durant la propagation de la fissure. Cette méthode permet une meilleure estimation dela position front de fissure ainsi que l'étude de la répartition des contraintes le long du joint de colle.La corrélation d'images numériques (DIC) a également été utilisée afin de proposer un nouveauprotocole de calibrage de la longueur de fissure et pour comparer un modèle analytique (poutre deTimoshenko sur fondation élastique) avec les résultats expérimentaux. / Adhesive bonding is being strongly considered in space applications CNES as anadvantageous assembly technique for future launchers. Correct design of adhesive joints is of majorconcern. Aerospace adhesives are tough viscoelastic matrices (special epoxy resins) reinforced withnano-, or microparticles. Extended use of adhesive joints in structural applications is limited due to thedifficulties in predicting in-service performance, frequently leading to over-conservative design.Three structural adhesives (Hysol®EA 9321, Hysol®EA 9394 and Hysol®EA 9395) wereselected. After their bulk characterization, statistical studies to highlight effects of different parameterse.g. speed, test piece geometry, degree of polymerization were undertaken.In the second stage, fracture mechanics tests were effected employing: the double cantileverbeam (DCB) configuration (mode I characterisation), the three point bending end-notched flexure(ENF) (mode II) and the mixed-mode bending (MMB) (combined mode I/II loading). Crack growth inbonded joints was investigated in a novel way. To refine standard test protocol, the backface strainmonitoring technique was used. Strain gauges were used to measure the strain on the exposed skin ofthe adherends during crack onset and propagation. This method allows better estimation of the crackfront position as well as fine investigation of the stress distribution along the bondline and in the crackfront vicinity. Digital image correlation (DIC) was also used to compare analytical models, e.g.Timoshenko beam on elastic foundation model with experimental results.

External post-tensioning is an attractive technique for strengthening reinforced concrete structures because of its ability to actively control stresses and deflections, speed of installation, minimum interruption for the existing structure, and ease of inspection under service conditions. However, external prestressing implies exposing the tendons to the environment outside the concrete section, which may lead to corrosion in steel tendons. Therefore, the interest in using fiber reinforced polymer (FRP) tendons, which are corrosion resistant, has increased. The present work investigated, experimentally and analytically, the flexural performance of reinforced concrete beams strengthened with externally post-tensioned Carbon FRP (CFRP) tendons, under monotonic and fatigue loadings. Initially, tensile fatigue tests were carried out on CFRP tendon-anchor assemblies to assess their response under repeated cyclic loads, before implementing them in the beam tests. New wedge-type anchors (Waterloo anchors) were used in gripping the CFRP specimens. The assemblies exhibited excellent fatigue performance with no premature failure occurring at the anchorage zone. The fatigue tests suggested a fatigue limit of a stress range of 10% of the tendon ultimate capacity (approximately 216 MPa). Monotonic and fatigue experiments on twenty-eight beams (152x254x3500 mm) were then undertaken. Test parameters included the tendon profile (straight and double draped), the initial loading condition of the beam prior to post-tensioning (in-service and overloading), the partial prestressing ratio (0.36 and 0.46), and the load ranges applied to the beam during the fatigue life (39% to 76% of the yield load). The CFRP tendons were post-tensioned at 40% of their ultimate capacity. The monotonic tests of the post-tensioned beams suggested that overloading the beam prior to post-tensioning increased the beam deflections and the strains developed in the steel reinforcing bars at any stage of loading. However, overloading had no significant effect on the yield load of the strengthened beam and the mode of failure at ultimate. It also had no discernable effect on the increase in the tendon stress at yielding. The maximum increase in the CFRP stress at yield load was approximately 20% of the initial post-tensioning stress, for the in-service and overloaded beams. A very good performance of the strengthened beams was observed under fatigue loading. The fatigue life of the beams was mainly governed by the fatigue fracture of the internal steel reinforcing bars at a flexural crack location. Fracture of the bars occurred at the root of a rib where high stress concentration was likely to occur. No evidence of wear or stress concentration were observed at the deviated points of the CFRP tendons due to fatigue. The enhancement in the fatigue life of the strengthened beams was noticeable at all load ranges applied. Post-tensioning considerably decreased the stresses in the steel reinforcing bars and, consequently, increased the fatigue life of the beams. The increase in the fatigue life was slightly affected by the loading history of the beams. At the same load range applied to the beam, increasing the amount of the steel reinforcing bars for the same post-tensioning level decreased the stress range in the bars and significantly increased the fatigue life of the strengthened beams. In the analytical study, a monotonic model that predicts the non-linear flexural response of the CFRP post-tensioned beams was developed and implemented into a computer program. The model takes into account the loading history of the strengthened beams prior to post-tensioning (in-service and overloading). Good agreement was obtained between the measured and the predicted monotonic results. A strain-life based fatigue model was proposed to predict the fatigue life of the CFRP post-tensioned beams. The model takes into consideration the stress-strain history at the stress raisers in the steel bars. It accounts for the inelastic deformation occurring at the ribs during cycling and the resulting changes in the local mean stresses induced. Good agreement between the experimental and predicted fatigue results was observed. A step-by-step fatigue design approach is proposed for the CFRP externally post-tensioned beams. General conclusions of the study and recommendations of future work are given.