Shock-shock interactions are among the most basic gas-dynamic problem, and are almost unavoidable in any high speed light, where shock waves generating from different sources crosses each other paths. These interactions when present very close to the solid surface lead to very high pressure and thermal loads on the surface. The related practical problem is that experienced at the cowl lip of a scramjet engine, where the interfering shock waves leads to high heat transfer rates which may also lead to the damage of the material. The classification by Edney (1968) on the shock-shock interaction patterns based on the visualization has since then served the basis for such studies. Though the problem of high heating on the surface in the vicinity of the shock-shock interactions has been studied at length at supersonic Mach numbers, the study on the topic at the hypersonic Mach numbers is little sparse. Even in the studies at hypersonic Mach numbers, the high speeds are not simulated, which is the measure of the kinetic energy of the ow. Very few experimental studies have addressed this problem by simulating the energy content of the ow. Also, some of the numerical studies on the shock-shock interactions suggest the presence of unsteadiness in the shock-shock interaction patterns as observed by Edney (1968), though this observation is not made very clearly in the experimental studies undertaken so far. In the present study, experiments are carried out in a conventional shock tunnel at Mach number of 5.62 (total enthalpy of 1.07 MJ/kg; freestream velocity of 1361 m/s), with the objective of mapping the surface pressure distribution and surface convective heat transfer rate distribution on the hemispherical body in the presence of the shock-shock interactions. A shock generator which is basically a wedge of angle = 25 , is placed at some dis-dance in front of the hemispherical body such that the planar oblique shock wave from the shock generator hits the bow shock wave in front of the hemi-spherical body. The relative distance between the wedge tip and the nose of the hemispherical body is allowed to change in di erent experiments to capture the whole realm of shock-shock interaction by making the planar oblique shock wave interact with the bow shock wave at different locations along its trajectory. The study results in a bulk of data for the surface pressure and heat transfer rates which were obtained by placing 5 kulites pressure transducers, 1 PCB pressure transducer and 21 platinum thin lm gauges along the surface of the hemispherical body in a plane normal to the freestream velocity direction. Along with the measurement of the surface pressure and the surface heat transfer rates, the schlieren visualization is carried out to capture the shock waves, expansion fans, slip lines, present in a certain shock-shock interaction pattern and the measured values were correlated with the captured schlieren images to evaluate the ow build up and steady and useful test time thereby helping in understanding the ow physics in the presence of the shock-shock interactions. From the present study it has been observed that in the presence of Edney Type-I and Edney Type-II interaction, the heat transfer rates on the hemi-spherical body are symmetrical about the centerline of the body, with the peak heating at the centerline which drops towards the shoulder. For Edney Type-III, Edney Type-IV, Edney Type-V and Edney Type-VI interaction pattern, the distribution in not symmetrical and shifts in peak heat transfer rates being on the side of the hemispherical from which planar oblique shock wave is incident. Also, it is observed that for the interactions which appear within the sonic circle, Edney Type-III and Edney Type-IV, the heat transfer rates observe an unsteadiness, such that the gauges located close to the interaction region experiencing varying heat transfer rates during the useful test time of the shock tunnel. Few experiments were conducted at Mach 8.36 (total enthalpy of 1.29 MJ/kg; freestream velocity of 1555.25 m/s) and Mach 10.14 (total enthalpy of 2.67 MJ/kg; freestream velocity of 2258.51 m/s) for the con gurations representing Edney Type-III interaction pattern to further evaluate the unsteady nature observed at Mach 5.62 ows. The unsteadiness was evident in both the cases. It is realized that the short test times in the shock tunnels pose a constraint in the study of unsteady flow fields, and the use of tailored mode operation of shock tunnel can alleviate this constraint. Also, limited number of experiments in the present study, which are carried out in a Free Piston Shock Tunnel, helps to understand the need to conduct such study in high enthalpy test conditions.

The aim of this thesis is to analyze and determine the actual flow of oil and natural gas in Europe, from the results to draw conslusions of the weight of the EU's dependence on Russian energy supplies and subsequently to determine the possibilities and prospects for further security flows of oil and natural gas to the EU. Oil and natural gas are the basic strategic raw materials of world economics, including economics of European countries. Most of the European countries does not have adequate supplies of energy raw materials. In particular, EU countries are therefore dependent on external supplies of oil and natural gas. The first chapter of the thesis is focused on oil and natural gas as major raw materials for the current energy situation in Europe. I defined the terms "oil" and "natural gas" and I analyzed the significant deposits of these materials and described their current production and consumption in Europe. In the second chapter I focused on the current flows of oil and natural gas in Europe, particularly on the European network of pipelines. On the baisis of these two chapters I specified the weight of the EU's dependence on energy supplies from Russia and identified the main problems of these supplies. In the third chapter of the thesis I dealt with the security flow of oil and natural gas to the EU and its perspectives and I gave the EU energy policy. I have analyzed selected documents of European energy policy, the EU's energy mix and I identified possible ways to reduce the EU's energy dependency. I included diversification of supply routes and the diversification of EU energy mix among these options. In conclusion, I summarized the current European energy situation, assessed European energy policy and outlined its future development.

The aim of the thesis is the determination of investment cash flows generated from Finnish market development activities of a selected Russia-based small company, performing investment valuation using discounted cash flow method and presenting improvements which can rise the attractiveness for potential investors. It includes comprehensive investment valuation of the selected company at the seed stage of its` development, including the overview of current financial situation, usage a valuation model followed by stable growth and terminal value determination. Provided and copulated data serves as an example of complete valuation model for capital injections of future projects in the company, thanks to which the author is able to come to particular conclusions on the funding perspectives for the company. The results obtained through the analysis is assessed through the critical prism to be used as a basis for further suggestions on improvement.

<p>Co-axial dripping is one of the many ways to make drops with a core-shell structure for encapsulated materials. However, in systems where the capsule components are not density matched or surfactants are not used, the shell will eventually thin and break if not solidified in time. If the shell fails before solidifying, the core will leak out and result in a non-functional capsule. This study assumes that all capsules will fail once the core has reached 80% eccentricity, meaning a shell region has thinned to 20% of its original thickness (~70 µm). In reality, rupture of the shell depends more on stochastic defects and disturbances, but locally decreasing the shell thickness will increase the probability of capsule rupture. With this assumption, the survival time of a core-shell drop is inversely proportional to the relative velocity of the inner drop, where the greater this relative velocity, the faster the shell phase will thin. Stoke's law is generally used to approximate the speed of a sphere in a fluid. However, this study demonstrates that Stoke's law is insufficient for predicting the inner drop's motion for a compound drop. This is due to internal flows that develop within all fluid drops because of shear forces on the drop’s external face during freefall. For core-shell drops, prior studies report how the inner drop velocity can change in magnitude and direction as a function of its eccentricity, meaning its position within the outer drop. Since previous studies did not analyze this core-shell drop relationship with a 50 vol% core and a high viscosity shell, a model was built in COMSOL Multiphysics to understand how the claims from literature would apply to a previous encapsulation study (Betancourt, 2021). The model was also put through a series of validation tests that confirmed the model’s ability to accurately represent the speed and direction of inner drop motion. The final model configuration was then used to identify the transition point between buoyancy-driven and internal flow-driven failure modes observed during the production of core-shell drops in a previous encapsulation study for phase change materials (Betancourt, 2021). The model results showed how the estimated inner drop velocity was significantly reduced once accounting for the internal flows within the shell phase of a compound drop. While this study does help characterize the motion of an inner drop and could be used to find a material system with a favorable velocity profile, it is still recommended to use an in-air curing system to produce concentric capsules. Achieving a concentric capsule would still require this co-axial dripping setup to be modified significantly. </p> <p>Betancourt-Jimenez, D., Wells, B., Youngblood, J. P., & Martinez, C. J. (2021). Encapsulation of biobased fatty acid amides for phase change material applications. <em>Journal of Renewable and Sustainable Energy</em>, <em>13</em>(6), 064101. https://doi.org/10.1063/5.0072105</p>

Les travaux de thèse sont axés sur les méthodes numériques pour les écoulements diphasiques, compressibles, à faible vitesse, avec apparition soudaine de forts gradients de pression. La vitesse matérielle de chacune des phases étant très petite devant la célérité des ondes acoustiques, le régime d'écoulement est dit à faible nombre de Mach. Dans ce travail, la loi d'état de la phase considérée contient toujours une information mesurant sa plus ou moins grande compressibilité. Ainsi, la faible compressibilité de l'eau peut produire un régime d'écoulement où des sauts de pression importants apparaissent même si le nombre de Mach est très faible. La première partie de la thèse s'est focalisée sur un modèle diphasique dit homogène-équilibré. Les deux phases de l'écoulement ont alors la même vitesse, pression, température et même potentiel chimique. Un premier travail a été la construction de solveurs de Riemann approchés dits tout-nombre-de-Mach. En l'absence de transitoire rapide, ces solveurs basent leur contrainte de pas de temps sur la vitesse des ondes matérielles lentes et sont donc précis pour suivre ces dernières. En revanche, lorsqu'une onde de choc rapide traverse l'écoulement, ces solveurs s'adaptent automatiquement afin de la capturer. La seconde partie de la thèse s'est focalisée sur la prise en compte du couplage convection-source dans le cadre des modèles en approche bi-fluides avec effets de relaxation pression-vitesse. Dans ces modèles, les deux phases de l'écoulement possèdent leur propre jeu de variables. Dans ce travail, un schéma implicite à mailles décalées, basé sur l'influence des termes sources dans des problèmes de Riemann linéaires, a été proposé / The present work focuses on numerical methods for low-material velocity compressible two-phase flows with high pressure jumps. In this context, the material velocity of both phases is small compared with the celerity of the acoustic waves. The flow is said to be a low-Mach number flow. In this work, the equation of state of the considered phase always contains information relative to its compressibility. For example, the low-compressibility of liquid water may lead to fast transients in which high pressure jumps are produced even if the flow Mach number is low. The first part of this work has leaned on two-phase homogeneous-equilibrium models. Thus, both phases have the same velocity, pressure, temperature and the same chemical potential. The construction of what is called an all-Mach-number approximate Riemann solver has been conducted. When no fast transients come through the flow, the above solvers enable computations with CFL conditions based on low-material velocities. As a result, they remain accurate to follow slow material interfaces, or subsonic contact discontinuities. However, when fast shock waves propagate, these solvers automatically adapt in order to capture them. The second part of the thesis has been dedicated to the design of numerical methods enhancing the coupling between convection and relaxation for two-fluid models containing pressure-velocity relaxation effects. In such models, both phases have their own set of variables. A time-implicit staggered scheme, based on the influence of relaxation source terms on linear Riemann problems has been proposed.

Life insurance policies are not equally profitable is sense of expected value. In practice, profitability is an output of complex cash flow models, which need utilizing special systems and the run time of such calculation can be significant if number of policies is high. Therefore we consider variables, which change most frequently, stimulate the profitability model with several values of these variables and then we search for a regression model to explain the changes. We apply Gamma regression on the data. But what if there exist some policies which are negative? Then we determine these policies with logistic regression applied on data censored to the binary form. Loss of these policies is modelled using symmetrical Gamma model. These three models, when considered together, can be viewed as a single model, which is a generalization of the well known zero inflated count model. The most interesting part of inference in such model is diagnostics. We show that the basic types of residuals - Pearson, deviance and quantile - can be defined. We also build an ordinary linear model and we compare utility of these two approaches. While building models, we meet various statistical issues like dimension reduction of yield curve or dispersion proportional to sum insured. 1

A significant level of research is currently being carried out in the development of driver support systems as they are expected to play a key role in minimizing road vehicle accidents and creating a safe driving environment under harsh weather conditions. However, the performance of some components used by existing driver support systems like LIDAR and visual cameras are affected by extreme weather conditions such as heavy rain fall and snow. Therefore, it is paramount to identify key locations in an automotive vehicle where such systems are least affect by external weather conditions, thereby, improving their overall performance. The field of research that deals with such questions from a simulation perspective is called contamination modeling. At the moment, one of the biggest knowledge gaps in this field is how to consider the effect of different materials on the movement of liquids such as water on different automotive surfaces like glass, plastic, rubber and painted metal. The work presented in this research study has been carried out to investigate and establish the most suitable simulation strategies to match numerical predictions with experimental data for flow of water over different automotive surfaces. Following a comprehensive parametric study of simulation parameters, it was found that the most suitable model that can be tweaked to achieve different flow properties with different surfaces is a dynamic contact angle model. The Blended Kistler model available in STAR-CCM+ required specific values for static, advancing and receding contact angles to optimize a surface for a given material. Therefore, droplet experiments of two droplet sizes were initially carried out for all tested materials at different inclinations and necessary flow parameters were recorded. All experiments were carried out using an approach known as light induced fluorescence imaging where the captured images provided a very convenient method for post processing in computational software. Results from droplet experiments showed that water moved quickest on plastic and slowest on glass. Static contact angle measurements were carried out first on horizontal surfaces. Afterwards, the surface was inclined at 15, 30, 45, 60, and 75 degrees to measure changes in contact angle and velocities. The surfaces for glass and painted metal were directly taken from the door of a Volvo S60 while a separate surface was used for plastic and rubber. These results were then used to create simulation setups for rivulets in STAR-CCM+ with the multiphase modeling approach known as volume of fluid. Rivulet simulations were carried out for all four materials at five different inclinations and the results were compared and validated with experimental data. The results show good correlation between numerical predictions for rivulet movement and experimental data emphasising on the possibility of fine-tuning the surfaces of a simulation setup to represent different material properties.

<p>  </p> <p>Cavitation is one of the most common causes of failures in axial piston machines. Due to the detrimental effects that cavitation has on unit performance, it is of important consideration both in the design of new units and in defining the operational limits of existing market products. The work in this thesis aimed to contribute to the current knowledge in both areas, with a focus on design considerations with respect to cavitation scalability, and on operating conditions by measuring cavitation severity under separate and combined inciting parameters. Though the application of unit scaling is common in industry for the design of pump families, there have been no comprehensive attempts to quantify whether cavitation in fluid power units may be adequately accounted for in published scaling laws. In this thesis, the scalability of cavitation phenomena was examined through a CFD scaling study performed using a modified version of the Full Cavitation Model.  Results indicate that linear scaling is consistent in maintaining volumetric efficiency performance within 1% across scaled units up to eight times larger or smaller than the baseline. However, the gas and vapor volume distributions vary significantly between scaled units, due largely to the linear non-scalability of fluid inertia and turbulent factors. Physical exchange between phases within a working fluid was shown to be time-dependent, such that the scaled-down unit exhibits bubble collapse rates up to 30% and 150% greater than the baseline and scaled-up units, respectfully. Considering these effects, the presented work demonstrates a potential for increased cavitation damage area when downscaling a unit and reduced risk in upscaling, despite the scaling law being a reliable indicator for volumetric efficiency. </p> <p>To define a more complete study of cavitation under a variety of operating conditions and inciting parameters, this a new experimental procedure and testing circuit was proposed with focus on repeatability by controlled pressure drops and preliminary quantification of inlet fluid quality. By measuring cavitation conditions under pressure starvation, incomplete filling, and combinations thereof, the direct effect of different inception methods on unit performance was shown to be readily identifiable. Through visualization of the inlet flow, reduction in inlet pressure levels was correlated to fluid cloudiness levels and bubble size, with transparency loss at 0.0 bar_g and transition from bubbly to plug flow at -0.4 bar_g. Incomplete filling-induced cavitation was also shown to be detectable by inlet flow conditions, with a distinct change in bubble coalescence rate when operating under shaft speeds greater than or equal to fill speed for a given inlet pressure. </p>

ITC/USA 2007 Conference Proceedings / The Forty-Third Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2007 / Riviera Hotel & Convention Center, Las Vegas, Nevada / In a modern ground control network for space communications, secure peer-to-peer TCP/IP network socket connections are typically used to transfer real-time telemetry and command frames between satellite operations centers and remote ground stations. Reliable and timely reconfiguration of data paths for upcoming pass supports becomes rather complex when many spacecraft and ground stations are involved. This paper describes a routing software application that was developed to facilitate switching of telemetry and command data paths between multiple ground stations and spacecraft command and control systems, and to forward telemetry streams to multiple client applications in parallel. Fully automated configuration and monitoring of the data flows is accomplished via a remote control interface that is tied into a pass scheduling system. The software is part of the SatTrack Suite and currently supports multi-mission flight operations, including those of the recently launched THEMIS constellation mission at Space Sciences Laboratory, University of California at Berkeley.

This thesis is focused on a simulation modelling approach to address the inventory inaccuracy problems in a warehouse operation. The main motivation which led to this research was a desire to investigate the inventory inaccuracy issues that have been highlighted by a logistics company. Previous and current research into inventory inaccuracy issues is largely related to the development of RFID technology as a possible solution to inventory problems. Since the inventory inaccuracy related to RFID technology is focused on the overall measurement of inventory management and retail business, there are differences between this existing research and the research presented in this thesis which is focused on issues of inventory inaccuracy in a warehouse operation. In this thesis, warehouse operation is studied as a detailed sequence of processes that are involved in the flow of items physically in parallel with related information being stored in the computer system. In these processes there are many places where errors can occur in counting or recording details of inventory, or in physically moving, storing or picking items incorrectly. These details of a warehouse operation are used to develop a conceptual model of inventory inaccuracy in warehouse operations. The study also found that typically a product needs to be considered differently at different stages of its progress through a warehouse (and therefore within different sections of the conceptual model). This is because initially batches of a product are likely to be delivered from a supplier, therefore if errors occur soon after the product is delivered to the warehouse, the error might involve the whole batch (for example the batch may be misplaced and put in an incorrect storage location), or the error might involve just part of the batch (for example poor transportation by forklift truck may damage the packaging carton and some of the items within the carton). When the product is stored ready for meeting customer orders, it needs to be considered as individual items (and errors can occur in counting of individual items or individual items may be misplaced or stolen). Finally, when a customer order is received, the product will be picked and grouped to meet the requirements of the order (for example, one order may require 10 of the product whilst another order may require 20 of the product). Errors might again occur to the whole group or to just part of the group. (Continued ...)