During the three decades, the torsional impact on turbine-generator sets due to power system disturbances has been extensively discussed in many research works. However, most of them are focused on the fatigue damage of turbine shafts due to large-signal disturbances. For example, network faults occur. Obviously, the torsional effect subject to small-signal disturbances has not received much attention. In fact, although the small disturbances would not immediately damage the turbine mechanism, the cumulative long-term damaging effects may not be negligible under certain circumstances. Many operating conditions in power systems may lead to small disturbances on blades; for examples, shedding loads, switching transmission line, resetting control system parameters, and harmonics etc. Nevertheless, others only cause short-term or transient non-resonant disturbances occasionally except the power system subharmonics which could results in electro-mechanical resonance. Therefore, two types of subharmonics in power systems are proposed so as to investigate the toque impact and long-term fatigue life expenditure in turbine shafts and blades. Firstly, from the steady-state disturbance viewpoint, the long-term cumulative fatigue estimation based on the three-year project of the GE Co. shows that there are potential damages for both the shafts and the blades of the nearby generators caused by the subharmonic excitations of the HVDC link. The fatigue life sensitivity works are also carried out to provide the recommendations for the safety operation. The optimal damper type and disposition scheme for depressing the resonant torque and prolonging the turbine lifetime is consequently motivated, which is based on participation factor of linear systems with the electromechanical analogy. The effectiveness of this scheme on suppressing vibration torque arising from network faults is also satisfying. In addition, the authors propose the new electromechanical supersynchronous resonance phenomenon for the turbine-generators near the inverter station owing to asymmetric line faults near the rectifier station. Secondly, the dramatic real and reactive power consumption during the melting period of an electrical arc furnace load. The voltage flicker pollution is mainly caused by the reactive power fluctuation while the stochastic subsynchronous oscillation in turbine mechanism is excited by the electromagnetic torque of the subsynchronous frequency which is induced by the real power fluctuation. Such a small stress imposed on the low-pressure long turbine blade combined with its evitable corrosive environment contributing to the corrosion fatigue effect. Although the voltage flicker severity at the point of common coupling is still within the limit, the blade may have been damaged from the long-term corrosion fatigue life expenditure estimation. In other words, the conventional voltage flicker limit established to make human-eye comfortable might not protect the blade from damaging risk. The long-term influence resulted from the electric arc furnace loads cannot always be neglected. It is necessary to take care of the blade material intensity and operating environment. If there is the potential of blade damage, one has to strengthen the output capacity at the power plant or separate the peak load durations among the steel plants to limit the over-fluctuation real power of the generator.

The performance of the High voltage dc systems is dependent on the stiffness of the ac bus, it is connected to. With the traditional synchronous reference frame-phase locked loops (SRF-PLL), voltage source converters (VSC) systems with large PLL gains, connected to weak ac networks are shown to be prone to instabilities, when subject to disturbances. In this thesis a new Adaptive PLL is designed with a pre-filter topology which extracts the fundamental positive sequence component of the input voltage, to be fed into the SRF-PLL for tracking of its phase angle. Compared with other traditional PLL topologies, this Adaptive PLL shows superior immunity to voltage distortions, and also has a faster dynamic performance. The thesis presents a comparative analysis of the performance of the traditional SRF-PLL with the Adaptive PLL in a VSC control system, and its impact on stability for VSCs connected to weak ac systems (up to SCR=1.3).

No description available.

The proliferation of distributed energy resources (DER)s has prompted interest in the expansion of DC power systems. The technological limitations that hinder the expansion of DC power systems are the absence of DC circuit breakers and high step-up/high step-down DC converters for interconnecting DC systems. This thesis presents a transformerless high step-up DC-DC converter intended for use as an interconnect between DC systems. The converter is required to operate at medium to high voltage (>1kV) and provide high voltage gain (>5). This work details the steady state operation and dynamic model of the proposed converter. The component ratings are identified and converter design limitations are investigated. A 100V:1kV/4kW prototype is produced to verify the analytic steady state model and measure efficiency. An experimental efficiency of 90% was achieved at a step-up ratio of 1:10, however efficiency at low power is limited due to the need to circulate power.

The proliferation of distributed energy resources (DER)s has prompted interest in the expansion of DC power systems. The technological limitations that hinder the expansion of DC power systems are the absence of DC circuit breakers and high step-up/high step-down DC converters for interconnecting DC systems. This thesis presents a transformerless high step-up DC-DC converter intended for use as an interconnect between DC systems. The converter is required to operate at medium to high voltage (>1kV) and provide high voltage gain (>5). This work details the steady state operation and dynamic model of the proposed converter. The component ratings are identified and converter design limitations are investigated. A 100V:1kV/4kW prototype is produced to verify the analytic steady state model and measure efficiency. An experimental efficiency of 90% was achieved at a step-up ratio of 1:10, however efficiency at low power is limited due to the need to circulate power.

One of the requirements for the next generation of power supplies for distributed power systems (DPSs) is to achieve high power density with high efficiency. In the traditional front-end converter based on the two-stage approach for high-power three-phase DPSs, the DC-link voltage coming from the power factor correction (PFC) stage penalizes the second-stage DC/DC converter. This DC/DC converter not only has to meet the characteristics demanded by the load, but also must process energy with high efficiency, high reliability, high power density and low cost. To meet these requirements, approaches such as the series connection of converters and converters that reduce the voltage stress across the main devices have been proposed. In order to improve the characteristics of these solutions, this dissertation proposes high-efficiency, high-density DC/DC converters for high-power high-voltage applications. In the first part of the dissertation, a DC/DC converter based on a three-level structure and operated with pulse width modulation (PWM) phase-shift control is proposed. This new way to operate the three-level DC/DC converter allows soft-switching operation for the main devices. Zero-voltage switching (ZVS) and zero-voltage and zero-current switching (ZVZCS) soft-switching techniques are studied, analyzed and compared in order to improve the characteristics of the proposed converter. This results in a series of ZVS and ZVZCS three-level DC/DC converters for high-power high-voltage applications. In all cases, results from 6kW prototypes operating at 100 kHz are presented. In addition, with the ultimate goal of improving the power density of the DC/DC converter, a study of several resonant DC/DC converters that can operate at higher switching frequencies is presented. From this study, a three-element ZVS three-level resonant converter for applications with wide input voltage and load variations is proposed. Experimental results at 745 kHz obtained without penalizing the efficiency of the PWM approaches are presented. The second part of the dissertation proposes a quasi-integrated AC/DC three-phase converter that aims to reduce the complexity and cost of the traditional two-stage front-end converter. This converter improves the complexity/low-efficiency tradeoff characteristics evident in the two-stage approach and previous integrated converters. The principle of operation for the converter is analyzed and verified on a 3kW experimental prototype. / Ph. D.

Le transport d’énergie par des lignes HVDC constitue le principal réseau de transmission d’énergie électrique du futur. Les convertisseurs de puissance (par exemple de type MMC) qui constitueront ce réseau devront être capables de gérer des tensions de l’ordre de centaines de kilovolts ce qui rend critique l’alimentation des dispositifs de contrôle (gate-drive) de ces convertisseurs. Il est nécessaire de concevoir des solutions qui garantissent l’alimentation de ces gate-drives avec une isolation.Pour ce faire, un circuit basé sur le principe du flyback et utilisant un JFET normalement passant a été développé. Il est placé en parallèle d’un condensateur typiquement connecté aux bornes d’un bras d’onduleur. Il permet d’alimenter le dispositif de puissance dès qu’une faible tension est appliquée à son entrée. Cette fonction est assurée grâce au caractère normalement passant du JFET. Pour le prototype développé, la tension du bras est de 2 kV. La tension de sortie est régulée à 24 V. De nos jours, des JFET normalement passants avec une tenue en tension supérieure à 2 kV n’existent pas sur le marché. Donc, pour supporter les tensions mises en jeu dans le circuit, une mise en série de JFET SiC normalement passants commandés par un MOSFET Si a été réalisée (montage « super-cascode »). Le circuit développé est capable de fournir 20 W pour alimenter des gate-drives à des potentiels flottants. Le rendement obtenu est proche de 60 %. Aussi, le problème d’isolation est résolu par cette solution d’auto-alimentation. / HVDC power transmission is the future of the electrical energy transmission network. The power converters (e.g. MMC) used in this network will be able to cope with voltages of hundreds of kV, making the power supply of the gate-drive devices in these converters challenging. It is then necessary to design solutions that guarantee the power supply of these gate-drives, while providing high voltage isolation. To do this, a circuit, based on the flyback principle, was developed. It is placed in parallel with a capacitor typically connected to a half-bridge circuit. It has an auto-start feature. This allows to supply the gate-drive as soon as a low voltage is applied to the input of the self-supply system. This is obtained by taking advantage of the normally-ON character of the JFET. In our prototype, the input voltage is 2 kV. High voltage JFETs of 2 kV and higher breakdown voltages are not yet available on the market. So, to achieve this high voltage capacity, a series of Normally-ON SiC JFETs controlled by a low voltage Si MOSFET (Super-cascode circuit) is used in the circuit. The developed circuit is able to supply 20 W at different floating potentials with output voltage regulated at 24 V and an efficiency close to 60%. The isolation problem is then solved using this solution.

För sammankoppling av multi-terminala HVDC-system med punkt-till-punkt kopplingar ärDC-DC-omvandlaren den enda möjliga sammankopplingen. Därför genomgår problemenmed spänningsmatchning och likspänningsströmbegränsning i högspännings DC-systemomfattande forskning samt ligger i fokus för denna avhandling. Först analyseras toppmodernatopologier för högspännings DC-DC-omvandlare som används för samtrafik av flera terminalaHVDC-system. De analyserade topologierna jämförs sedan baserat på dess olika funktioner.Topologin för en konventionell icke-isolerad DC-DC-omvandlare analyseras när det gäller design,kostnad, storlek, förlust och effektstyrningskapacitet. Först skapas en matematisk modell ochsedan utförs en numerisk analys för olika arbetsområden. Därefter görs en jämförelse av entvåfas-icke-isolerad DC-omvandlare baserad på energilagring, maximal likströmsöverföring ochtotala förluster. Simulering utförs av en tvåfas och en trefas icke-isolerad DC-omvandlare iPSCAD med olika typer av styrenheter. Dessutom tas en isolerad omvandlartopologi och analyserasi detalj från matematisk modellering till validering med hjälp av simuleringsresultat.Olika typer av felanalyser för både isolerad och icke-isolerad omvandlartopologi görs. Slutligenutförs även analyser av DC-felet i olika möjliga anslutningar av omvandlaren i Multi-TerminalGrid, dvs Monopole, Bipole med både symmetriska och asymmetriska konfigurationer. / For interconnection of multi-terminal HVDC systems involving point-to-point links, aDC-DC converter is the only possible way to interconnect. Therefore, the issues of voltagematching and DC fault current limiting in high voltage DC systems are undergoing extensiveresearch and are the focus of this thesis. Starting with analyzing the state of the art highvoltage DC-DC converter topologies for interconnection of multi-terminal HVDC systems andbenchmarking each converter topology based on different functionalities. A basic non-isolatedDC-DC converter topology is analyzed in terms of design, cost, sizing, losses and power controlcapability. First, starting with the mathematical modeling and then the numerical analysis isdone for different operating regions. Next, it is compared with the two-phase non-isolated DCconverter based on energy storage, maximum DC power transfer, and total losses. Simulation oftwo-phase and three-phase non-isolated DC converter is done in PSCAD incorporating differenttypes of controllers. Then, an isolated converter topology is taken and analyzed in detail startingfrom mathematical modeling to validation using simulation results. Different types of faultsanalysis for both isolated and non-isolated converter topology is done. Finally, analyzing the DCfault in different possible connection of the converter in the multi-terminal grid, i.e. monopole,bipole in both symmetric and asymmetric configurations.