Spelling suggestions: "subject:"highefficiency"" "subject:"highefficiency""
141 |
Gallium Nitride: Analysis of Physical Properties and Performance in High-Frequency Power Electronic CircuitsSaini, Dalvir K. 11 August 2015 (has links)
No description available.
|
142 |
Efficient radio frequency power amplifiers for wireless communicationsCui, Xian 10 December 2007 (has links)
No description available.
|
143 |
Form-Factor-Constrained, High Power Density, Extreme Efficiency and Modular Power ConvertersWang, Qiong 18 December 2018 (has links)
Enhancing performance of power electronics converters has always been an interesting topic in the power electronics community. Over the years, researchers and engineers are developing new high performance component, novel converter topologies, smart control methods and optimal design procedures to improve the efficiency, power density, reliability and reducing the cost. Besides pursuing high performance, researchers and engineers are striving to modularize the power electronics converters, which provides redundancy, flexibility and standardization to the end users. The trend of modularization has been seen in photovoltaic inverters, telecommunication power supplies, and recently, HVDC applications.
A systematic optimal design approach for modular power converters is developed in this dissertation. The converters are developed for aerospace applications where there are stringent requirement on converter form factor, loss dissipation, thermal management and electromagnetic interference (EMI) performance. This work proposed an optimal design approach to maximize the nominal power of the power converters considering all the constraints, which fully reveals the power processing potential. Specifically, this work studied three-phase active front-end converter, three-phase isolated ac/dc converter and inverter. The key models (with special attention paid to semiconductor switching loss model), detailed design procedures and key design considerations are elaborated. With the proposed design framework, influence of key design variables, e.g. converter topology, switching frequency, etc. is thoroughly studied.
Besides optimal design procedure, control issues in paralleling modular converters are discussed. A master-slave control architecture is used. The slave controllers not only follow the command broadcasted by the master controller, but also synchronize the high frequency clock to the master controller. The control architecture eliminates the communication between the slave controllers but keeps paralleled modules well synchronized, enabling a fully modularized design.
Furthermore, the implementation issues of modularity are discussed. Although modularizing converters under form factor constraints adds flexibility to the system, it limits the design space by forbidding oversized components. This work studies the influence of the form factor by exploring the maximal nominal power of a double-sized converter module and comparing it with that of two paralleled modules. The tradeoff between modularity and performance is revealed by this study. Another implementation issue is related to EMI. Scaling up system capacity by paralleling converter modules induces EMI issues in both signal level and system level. This work investigates the mechanisms and provides solutions to the EMI problems. / Ph. D. / As penetration of power electronics technologies in electric power delivery keeps increasing, performance of power electronics converters becomes a key factor in energy delivery efficacy and sustainability. Enhancing performance of power electronics converters reduces footprint, energy waste and delivery cost, and ultimately, promoting a sustainable energy use. Over the years, researchers and engineers are developing new technologies, including high performance component, novel converter topologies, smart control methods and optimal design procedures to improve the efficiency, power density, reliability and reducing the cost of power electronics converters. Besides pursuing high performance, researchers and engineers are striving to modularize the power electronics converters, enabling power electronics converters to be used in a “plug-and-play” fashion. Modularization provides redundancy, flexibility and standardization to the end users. The trend of modularization has been seen in applications that process electric power from several Watts to Megawatts. This dissertation discusses the design framework for incorporating modularization into existing converter design procedure, synergically achieving performance optimization and modularity.
A systematic optimal design approach for modular power converters is developed in this dissertation. The converters are developed for aerospace applications where there is stringent v requirement on converter dimensions, loss dissipation, and thermal management. Besides, to ensure stable operation of the onboard power system, filters comprising of inductors and capacitors are necessary to reduce the electromagnetic interference (EMI). Owning to the considerable weight and size of the inductors and capacitors, filter design is one of the key component in converter design. This work proposed an optimal design approach that synergically optimizes performance and promotes modularity while complying with the entire aerospace requirement. Specifically, this work studied three-phase active front-end converter, three-phase isolated ac/dc converter and three-phase inverter. The key models, detailed design procedures and key design considerations are elaborated. Experimental results validate the design framework and key models, and demonstrates cutting-edge converter performance.
To enable a fully modularized design, control of modular converters, with focus on synchronizing the modular converters, is discussed. This work proposed a communication structure that minimizes communication resources and achieves seamless synchronization among multiple modular converters that operate in parallel. The communication scheme is demonstrated by experiments.
Besides, the implementation issues of modularity are discussed. Although modularizing converters under form factor constraints adds flexibility to the system, it limits the design space by forbidding oversized components. This work studies the impact of modularity by comparing performance of a double-sized converter module with two paralleled modules. The tradeoff between modularity and performance is revealed by this study.
|
144 |
Ultracapacitor/Battery Hybrid Energy Storage Systems for Electric VehiclesMoshirvaziri, Mazhar 22 November 2012 (has links)
This thesis deals with the design of Hybrid Energy Storage System (HESS) for Light Electric Vehicles (LEV) and EVs. More specifically, a tri-mode high-efficiency non-isolated half-bridge converter is developed for the LEV based HESS applications. A 2 kW, 100 V interleaved two-phase converter prototype was implemented. The peak efficiency of 97.5% and a minimum efficiency of 88% over the full load range are achieved.
Furthermore, a power-mix optimizer utilizing the real-time Global Positioning System (GPS) data for the EV based HESS is proposed. For a specific design, it is shown that at the cost of less than 1.5% of the overall energy savings, the proposed scheme reduces the peak battery charge and discharge rates by 76% and 47%, respectively. A 30 kW bi-directional dc-dc converter is also designed and implemented for future deployment of the designed HESS into a prototype EV, known as A2B.
|
145 |
Ultracapacitor/Battery Hybrid Energy Storage Systems for Electric VehiclesMoshirvaziri, Mazhar 22 November 2012 (has links)
This thesis deals with the design of Hybrid Energy Storage System (HESS) for Light Electric Vehicles (LEV) and EVs. More specifically, a tri-mode high-efficiency non-isolated half-bridge converter is developed for the LEV based HESS applications. A 2 kW, 100 V interleaved two-phase converter prototype was implemented. The peak efficiency of 97.5% and a minimum efficiency of 88% over the full load range are achieved.
Furthermore, a power-mix optimizer utilizing the real-time Global Positioning System (GPS) data for the EV based HESS is proposed. For a specific design, it is shown that at the cost of less than 1.5% of the overall energy savings, the proposed scheme reduces the peak battery charge and discharge rates by 76% and 47%, respectively. A 30 kW bi-directional dc-dc converter is also designed and implemented for future deployment of the designed HESS into a prototype EV, known as A2B.
|
146 |
Energy-efficient interfaces for vibration energy harvestingDu, Sijun January 2018 (has links)
Ultra low power wireless sensors and sensor systems are of increasing interest in a variety of applications ranging from structural health monitoring to industrial process control. Electrochemical batteries have thus far remained the primary energy sources for such systems despite the finite associated lifetimes imposed due to limitations associated with energy density. However, certain applications (such as implantable biomedical electronic devices and tire pressure sensors) require the operation of sensors and sensor systems over significant periods of time, where battery usage may be impractical and add cost due to the requirement for periodic re-charging and/or replacement. In order to address this challenge and extend the operational lifetime of wireless sensors, there has been an emerging research interest on harvesting ambient vibration energy. Vibration energy harvesting is a technology that generates electrical energy from ambient kinetic energy. Despite numerous research publications in this field over the past decade, low power density and variable ambient conditions remain as the key limitations of vibration energy harvesting. In terms of the piezoelectric transducers, the open-circuit voltage is usually low, which limits its power while extracted by a full-bridge rectifier. In terms of the interface circuits, most reported circuits are limited by the power efficiency, suitability to real-world vibration conditions and system volume due to large off-chip components required. The research reported in this thesis is focused on increasing power output of piezoelectric transducers and power extraction efficiency of interface circuits. There are five main chapters describing two new design topologies of piezoelectric transducers and three novel active interface circuits implemented with CMOS technology. In order to improve the power output of a piezoelectric transducer, a series connection configuration scheme is proposed, which splits the electrode of a harvester into multiple equal regions connected in series to inherently increase the open-circuit voltage generated by the harvester. This topology passively increases the rectified power while using a full-bridge rectifier. While most of piezoelectric transducers are designed with piezoelectric layers fully covered by electrodes, this thesis proposes a new electrode design topology, which maximizes the raw AC output power of a piezoelectric harvester by finding an optimal electrode coverage. In order to extract power from a piezoelectric harvester, three active interface circuits are proposed in this thesis. The first one improves the conventional SSHI (synchronized switch harvesting on inductor) by employing a startup circuitry to enable the system to start operating under much lower vibration excitation levels. The second one dynamically configures the connection of the two regions of a piezoelectric transducer to increase the operational range and output power under a variety of excitation levels. The third one is a novel SSH architecture which employs capacitors instead of inductors to perform synchronous voltage flip. This new architecture is named as SSHC (synchronized switch harvesting on capacitors) to distinguish from SSHI rectifiers and indicate its inductorless architecture.
|
147 |
Conception optimale d’une gamme de moteurs synchrones à démarrage direct à haute performance énergétique / Optimal design of line-start permanent magnet synchronous motors of high efficiencyElistratova, Vera 06 November 2015 (has links)
Ce travail a pour objectif de développer un outil analytique multi-physiques de dimensionnement d’une gamme de moteurs « hybrides » à démarrage direct, intégrant les avantages des deux technologies : l’auto-démarrage de la technologie asynchrone et les bonnes performances énergétique en régime permanent de la technologie synchrone à aimants permanents en répondant aux nouveaux enjeux d’efficacité énergétique et en ajoutant à cela les aspects économiques.La validation de cet outil est effectuée par des modèles éléments finis créés avec un logiciel commercial ANSYS/Maxwell et par des essais expérimentaux réalisés à l’aide de deux prototypes LSPMSM 7.5kW. / This work aims to develop a multi-physical generic model (and a pre-design software) for a range of LSPMSMs which would integrate the advantages of both technologies: self-start asynchronous technology and good energy performance of synchronous permanent magnet technology. The validation of this model is carried out by finite element commercial software ANSYS / Maxwell and by experimental tests using two 7.5kW.LSPMSM prototypes.
|
148 |
Spínané zdroje / Switched Mode Power SuppliesŠpaněl, Petr January 2020 (has links)
This thesis deals with switched mode power supplies based on resonant principle to achieve high efficiency. Several ways of switched mode power supplies optimalisation are described as part of the work to achieve better efficiency. Priparily, the new generation of switching elements based on SiC and resonant topology are used to achieve significant switching loss minimization. The selected resonant topology is simualted in detail and then built with focus on high efficiency. The main content of the work consists in the design and realization of the switched mode power supply with selected control algorithms and their comparison. The problems associated with usage of new SiC MOSFET generation in TO-247-4L package are being solved within the design and implementation of the power source. To solve the main problems, new 3rd SiC MOSFET gate driver was developer for working with switching frequencies in hundreds of kHz and resisting very high voltage stress on the controlled transistor. The next part of the gate driver is the overcurrent protection. The overcurrent limit can be set easily by changing one component. This protection reacts very quickly in hundreds of nanoseconds, so it is capable of saving the converter even in branch failure and going to hard short circuit. The functional sample of the series resonant converter was built and revated in the work. The converter based on 3. Generation of SiC MOSFET transistors from Cree in a modern case TO-247-4L was built. For this inverter, it was also necessary to develop both the control scheme and the resonance frequency tracking to achieve accurate switching and thus achieve the use of the resonant principle of the converter to the maximum extent possible. The result of this work is up to 3 kW converter with adjustable output voltage while maintaining high efficiency up to 96%.
|
149 |
Laboratorní zdroj s vysokou účinností / High efficiency laboratory power supplyTejmlová, Lenka January 2011 (has links)
The project shows the problems of power supply in electrical engineering. It describes the general parameters of these types of supplies and presents their characteristics. Based on these findings, it is also focused on the selection of specific elements of the laboratory supply, to reach the given parameters. It contains the recalculations of the parameters of other additional components. The overall scheme of the supply is divided into several blocks, thematically corresponded to subchapters. According to the accomplished concept the laboratory supply is realized and its parameters had been tested. Projects results are assessed at the end.
|
150 |
Characterization of Aerosols and Airborne Particles in a Dental SettingSadoughipour, Niloufar 15 September 2022 (has links)
No description available.
|
Page generated in 0.2916 seconds