Des membranes polymères catalytiques ont été préparées via la polymérisation photo-amorcée de monomères acryliques à la surface de membranes support MicroPES(r). Des nanoparticules de palladium (PdNP) avec diamètre moyen compris entre 4 et 10 nm sont ensuite synthétisés et immobilisées dans ces gels polymères greffés. Cette thèse se focalise sur le greffage d'un gel de polymère neutre : (2-hydroxyethyl acrylate) (PHEA), pour négliger les contributions ioniques du réseau polymère sur la synthèse in-situ des PdNP. La stabilisation de PdNP dans le gel de PHEA greffé est possible par des moyens stériques étant donné que la distance entre des chaînes de polymère réticules (entre 0.3 à 2.5 nm) est plus petite que le diamètre moyen de PdNP. Une approche à la fois théorique et expérimentale, sur la base des mecanismes de nucléation et de croissance, permet la conception de PdNP de taille spécifique. La performance catalytique des membranes a été évaluée avec une configuration en filtration traversée. Sur la réaction de couplage de Suzuki-Miyaura, des conversions et sélectivités de 100 % ont été obtenues pour des temps de séjour de 10 secondes avec des membranes planes. Les réactions d'hydrogénation de plusieurs composés aromatiques ont également été testées. Des taux de conversion élevés ont été obtenus en quelques secondes avec des membranes planes en filtration avec des solutions saturés d'H2. Des taux de conversion élevés sont obtenus en seulement quelques minutes avec des membranes fibres creuses catalytiques en mode contacteur permettant une importante intensification du procédé. / Catalytic polymeric membranes are prepared via photo-grafting polymerization of neutral acrylic monomers onto the surface of a MicroPES(r) membrane support. Palladium nanoparticles (PdNP) of mean diameter of 4-10 nm are synthetized and immobilized within the grafted polymer gels. The research is focused on grafting a neutral polymer gel: poly (2-hydroxyethyl acrylate) (PHEA), to avoid any ionic contribution of the polymer network on the in-situ synthesis of PdNP. The stabilization of PdNP within the grafted PHEA is achieved by steric means as the distance between polymeric crosslinked chains (ca. 0.3 to 2.5 nm) is smaller than the mean diameter of PdNP. Both theoretical and experimental approaches are presented on the PdNP synthesis as an approach to conceive PdNP of specific sizes using nucleation and growth theories. Catalytic performance of the membranes is evaluated in flow-through configuration. Catalytic tests are performed on Suzuki-Miyaura cross-coupling reactions. Full conversion and selectivity within 10 seconds of residence time using flat sheet membrane are obtained. Hydrogenation of several aromatic compounds are also tested and high conversions were achieved within seconds of residence time using flat sheet membranes in flow-through configuration with H2-saturated solutions and within minutes using catalytic hollow fibers in contactor mode.

Die Verringerung von CO2-Emissionen und die Schaffung eines Kohlenstoffkreislaufs sind Gegenstand vieler Forschungsarbeiten. Mittels Absorption wird CO2 in einem Lösungsmittel (vorrangig Alkoholamine) aus verschiedenen Gasmischungen abgetrennt und anschließend zu Wertstoffen umgesetzt. In der vorliegenden Arbeit war ein kombiniertes Verfahren aus CO2-Absorption und direktem Umsatz von CO2 zu Methanol im Amin zu untersuchen. Die Einsparung des Desorptionsschritts und die Möglichkeit zur Reduzierung der Reaktionstemperatur des exothermen Hydrierprozesses sind wesentliche Vorteile dieser Verfahrensweise. Um dieses Ziel zu erreichen, wurde die Performance verschiedener Amine untersucht und die Reaktionsparameter optimiert. Zur Verhinderung auftretender Nebenreaktionen fällt der Suche nach einem neuartigen Feststoffkatalysator besondere Bedeutung zu. Hierbei konnte ein Katalysatorsystem identifiziert werden, mit dessen Einsatz eine deutlich höhere Methanolausbeute als mit dem Standardkatalysator sowie eine Einschränkung der Nebenreaktionen erreicht wurde.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第22467号 / 工博第4728号 / 新制||工||1738(附属図書館) / 京都大学大学院工学研究科分子工学専攻 / (主査)教授 田中 庸裕, 教授 江口 浩一, 教授 佐藤 啓文 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Depuis plusieurs décennies, la chimie du palladium a connu un véritable essor. Afin de de continuer dans cette optique, plusieurs axes de recherche ont été investigués dans le cadre de cette thèse. Grâce aux récents développements de la catalyse duale palladium/norbornène, la réaction de couplage entre des triflates aryliques et des partenaires bromobenzylamines nous a permis d’accéder à des motifs benzophénanthridines naturels. En parallèle, une nouvelle famille de complexes triangulaires de palladium a été isolée dans notre groupe. Cette espèce arborant 44 électrons de valence et une charge positive délocalisée sur son cœur tri-métallique, est la première molécule stable qui présente un caractère métallo-aromatique de type δ. Après l’optimisation d’une nouvelle voie de synthèse, nous avons pu accéder à des analogues de platine mais aussi à des composés hétéro-métalliques possédant des unités asymétriques similaires. Le caractère base de Lewis de ces complexes ont permis l’isolation de composés tétraédriques de type [M”(M₃)(Ln)]²⁺ malgré la répulsion des charges positives. Ces espèces triangulaires aromatiques ont aussi prouvé leur habileté en tant que catalyseur pour la réaction de semi-hydrogénation d’alcynes. En effet, ce complexe transforme chimiosélectivement les alcynes en alcènes de configuration Z sans présence de produit doublement réduit. / Recent developments on dual palladium/norbornene catalytic reactions led to one-pot synthesis of complexes polyheterocyclic molecules. By extension of this reaction, the coupling of aryl triflates and bromobenzylamines permitted us to synthesize natural benzophenanthridine. In parallel, a new family of triangular palladium complexes has been isolated in our research group. These 44 valence electrons complexes possessing a positive charge delocalized on the trimetallic core were the first stable compounds which presented δ-type aromaticity. After optimization of a new synthetic route, we could be able to isolate platinum analogues and also heterometallic clusters which interestingly had the same asymmetric unit than their homonuclear peers. Despite the unavoidable charge repulsion, the Lewis basic character revealed to be strong enough to bind other cationic species. Indeed, we reached to synthesize tetrahedral [M”(M₃)(Ln)]²⁺ complexes. In another side, we wondered if the stability and special properties of [Pd₃]⁺ clusters could confer to it some catalytic activities. Our studies were focused on semi-reduction reactions of alkynes. After optimization process, the catalyst [Pd₃(SMe)₃{P(C₇H)₃)₃}]⁺ showed results beyond our greatest expectations. Indeed, this cluster selectively produced thermodynamically less stable Z-alkene without traces of over-reduced compound. Total chemioselectivity towards alkynes was proved by the reaction on several molecules bearing functional groups which are sensitive to hydrogenation conditions.

Die vorliegende Arbeit beschreibt die Präparation von Pt-Fe/SiO2-Katalysatorproben für die selektive Flüssigphasenhydrierung von Zimtaldehyd. Während der Herstellung wurden die Proben ausschließlich einer Reduktion bei 350 °C oder einer anschließenden Reduktion bei 750 °C unterworfen. Die präparierten Materialien wurden mit den Methoden ICP-OES, Laserbeugung, N2-Physisorption, XRD, TEM, SQUID und TPR/O charakterisiert. Daneben wurden Chemisorptions-Untersuchungen mit den Adsorptiven H2, O2 und CO durchgeführt. Infolge der angewandten Reduktionstemperatur von 750 °C konnte exemplarisch die Ausbildung von Metallpartikeln der Überstrukturphase nachgewiesen werden. Die katalytische Austestung der Materialien erfolgte in diskontinuierlich betriebenen Hydrierautoklaven. Hierbei stand die wertschöpfende Umsetzung zum Zimtalkohol im Vordergrund. Die Verwendung von Katalysatorproben, die Überstrukturphasen des Systems Fe-Pt aufweisen, führte nicht zu einer signifikanten Selektivitätsverbesserung zum Zielprodukt Zimtalkohol. Optimale Zimtalkohol-Ausbeuten ließen sich für Katalysatorproben erreichen, deren Metallpartikel nominelle Fe-Anteile von 30 bis 40 Mol.-% aufwiesen.

In this thesis a methodology to synthesize anti-β-hydroxy-α-amino esters possessing olefins has been investigated. The developed procedures originate from two already established procedures in which α-amido-β-keto esters, which do not contain olefins, has been stereoselectively reduced to the corresponding anti-β-hydroxy-α-amino alcohols via asymmetric transfer hydrogenation coupled with dynamic kinetic resolution. Both established methods, one solvent free and one emulsion procedure, have been investigated on the expanded substrate scoop. Four different α-amido-β-keto ester containing olefins were tested and it was found that the ketones were reduced to desired anti-β-hydroxy-α-amino esters in both procedures, but also side products were formed where the olefins were reduced. The ratio of the different products was dependent on the structure of the starting α-amido-β-keto ester, ligand used on the catalyst and reaction conditions such as number of equivalents of base and reaction temperature. The diastereoselectivity for the desired products was in favor of the anti stereoisomer, however, the dr was worse than in the established procedures. The usefulness of this methodology was then demonstrated by a formal total synthesis of Sphingosine.

The development of nanoscale heterostructure photocatalysts for the effective, direct utilization of visible light (400-750 nm, ~44% of solar spectrum) to drive important chemical conversions is a prime research area in the field of photocatalysis. Particles at nanoscale dimensions have a large surface area-to-volume ratio, expose a high number of active surface sites, and exhibit unique electronic properties (different from bulk) that are beneficial for improving the overall catalytic activity. However, the advantages of size reduction are often overshadowed by the low optical absorption (as absorption power  size3) and colloidal instability (extensive aggregation) of particles at the nanoscale. In this dissertation, we demonstrate a strategy to improve the colloidal stability and enhance the optical absorption of nano-sized semiconductor and metal nanoparticles (NPs) that exhibit weak visible light absorption. The colloidal, free-standing NPs are placed on transparent, dielectric silica nanospheres (SiOx NSs) that act as optical antenna supports, forming SiOx/NP composite nanostructures. The spherical morphology of SiOx enables scattering resonances (Fabry Perot or Whispering Gallery Modes) which enhances the local electric field on or near the surface of the NS. The NPs placed on the surface of SiOx NS interact with the locally enhanced electric field and exhibit improved optical absorption. By varying the size of the SiOx NS, the resonance wavelengths and the intensity of the local electric field enhancement can be tuned, offering the ability of such structures to effectively utilize a wide range of energies in the visible region. Composite nanostructures comprised of various classes of nanomaterials such as metal-doped semiconductor, plasmonic, and non-plasmonic metal NPs were investigated to perform the desirable solar-to-chemical transformations. First, we employed SiOx-loaded silver-doped silver chloride (SiOx/AgCl(Ag)) photocatalyst to investigate the role of metal-induced gap states in AgCl, a wide bandgap semiconductor. SiOx/AgCl(Ag) exhibit high catalytic performance and photostability after 10 cycles of the probe reaction, methylene blue (MB) degradation under visible light irradiation. The results indicate that the visible light absorption due to metal-induced gap states can be further improved by employing the SiOx NSs as supports that act as optical nanoantenna. We then studied the influence of NP size on the catalytic activity to understand the effect of size in promoting the generation and transfer of hot electrons to surface adsorbates. Our findings indicate that upon employing Ag NPs of different particle size (<10 nm and >10 nm) and normalizing for the optical absorption and moles of surface Ag atoms, the efficient generation and transfer of photoexcited hot electrons is favored in the small-sized Ag NPs (size <10 nm) than bigger Ag NPs. Next, we investigated the selective partial hydrogenation of nitroarene to N-aryl hydroxylamine using SiOx-loaded platinum (SiOx/Pt) photocatalysts. We found that change in the surface electronic structure of the small Pt NPs (size <5 nm) due to light illumination and surface modification (by adding suitable organic ligands), minimize the adsorption of the electron-rich hydroxylamine molecules and minimize their complete conversion to aniline, resulting in high N-hydroxylamine selectivity. Overall, our work shows that well-controlled composite nanostructures comprising of active catalyst loaded on dielectric SiOx NS supports that act as optical nanoantenna are a promising class of photocatalysts for driving photon-to-chemical transformations with high activity and product selectivity. / Chemistry

Increasing energy demand and various problems associated with fossil fuels such as environmental pollution, global warming and diminishing petroleum reserves have greatly stimulated production of fuels and chemicals from renewable sources. Lignocellulosic biomass has been considered as one of the potential sources for a variety of fuels and industrial chemicals. 5-Hydroxymethylfurfural (HMF) has been identified as an excellent platform molecule because it is a flexible intermediate for the synthesis of bio-renewable fuels and materials. HMF can be easily obtained from acid-catalyzed hydration of biomass-derived carbohydrates (hexoses) in various media. HMF can be converted to energy products such as 2,5-bis(alkoxymethyl)furans (BAMFs), monomers for high-value polymers such as 2,5-bis(hydroxymethyl)furan (BHMF), and valuable intermediates for fine chemicals. Recently, magnetic nanoparticle based catalysts attracted more attention due to their good stability and easy separation from the reaction mixture by a permanent magnet. This unique magnetic separation property makes MNPs more effective than conventional filtration or centrifugation as it prevents loss of the catalyst. This dissertation work focuses on, firstly, studying the effectiveness of silica coated magnetite (Fe3O4) nanoparticles MNPs supported with sulfonic acid groups (Fe3O4@SiO2-SO3H) on the dehydration of glucose to HMF. Secondly, preparing a cost-effective catalytic transfer hydrogenation system for the selective transformation of HMF into BHMF via Meerwein-Ponndorf-Verley (MPV) reaction over the copper iron magnetic catalyst supported on activated carbon in ethanol solvent with the absence of molecular hydrogen. Thirdly, producing alkoxymethylfurans (AMFs) which are considered a potential biofuels by using two-step sequential reactions with cheap heterogeneous zinc-iron oxides magnetic nanocatalyst for the hydrogenation of HMF to furfuryl alcohols in various alcohols solvents in the absence of molecular hydrogen followed by solid Brønsted acid catalyst for the etherification reaction of furfuryl alcohol derivatives. All prepared heterogeneous catalysts were characterized by FTIR, XRD, H2-TPR, XPS, ICP-OES, HRTEM-EDX, and N2 adsorption-desorption isothermal analyses (BET and BJH) and were tested for recyclability. The chemical products were identified by high performance liquid chromatography (HPLC), gas chromatography-mass spectrometry (GC-MS), and products quantities were calculated by using calibration curves of chemical standards. Various reaction conditions such as reaction temperature, reaction time, catalyst amount, and alcohol type were optimized.

A systematic silylation approach using mono-, di-, and trichlorosilanes with different alkyl chain lengths was employed to enhance the hydrothermal stability of zeolite Y. DRIFT spectra of the silylated zeolites indicate that the attachment of the silanes takes place at surface silanol groups. Regarding hydrothermal stability under aqueous-phase processing (APP) conditions, i.e., pH ≈ 2, 473 K and autogenous pressure, the selective silylation of the zeolite surface usingmonochlorosilanes has no considerable influence. By using trichlorosilanes, the hydrothermal stability of zeolite Y can be improved significantly as proven by a stability test in an aqueous solution of 0.2M levulinic acid (LA) and 0.6M formic acid (FA) at 473 K. However, the silylationwith trichlorosilanes results in a significant loss of total specific pore volume and total specific surface area, e.g., 0.35 cm3 g−1 and 507m2 g−1 for the silylated zeolite Y functionalized with n-octadecyltrichlorosilane compared to 0.51 cm3 g−1 and 788 m2 g−1 for the parent zeolite Y. The hydrogenation of LA to g-valerolactone (GVL) was conducted over 3 wt.-% Pt on zeolite Y (3PtY) silylated with either n-octadecyltrichlorosilane or methyltrichlorosilane using different reducing agents, e.g., FA or H2. While in the stability test an enhanced hydrothermal stability was found for zeolite Y silylated with n-octadecyltrichlorosilane, its stability in the hydrogenation of LA was far less pronounced. Only by applying an excess amount of methyltrichlorosilane, i.e., 10 mmol per 1 g of zeolite Y, presumably resulting in a high degree of polymerization among the silanes, a recognizable improvement of the stability of the 3 PtY catalyst could be achieved. Nonetheless, the pore blockage found for zeolite Y silylated with an excess amount of methyltrichlorosilane was reflected in a drastically lower GVL yield at 493 K using FA as reducing agent, i.e., 12 vs. 34% for 3PtY after 24 h.

No description available.