Detta arbete har genom experiment och tester undersökt förbättringspotentialen för en halvautomatisk grundtillsyn av Ra180. Eftersom att denna grundtillsyn tar lång tid är det högst relevant att försöka korta ner den. Genom noggranna mätningar som har testats har det tagits fram lämpliga lösningar för en påtaglig förbättring. I linje med detta har även en undersökning gjorts av huruvida en helautomatisk grundtillsyn är möjlig. Genom dessa undersökningar har också en hårdvaruprototyp till denna metod tagits fram och implementerats.

In biomedical applications realistic phantoms are becoming more useful for validation and testing of precursor systems. These artificial phantoms require stable and flexible tissue-mimicking materials with realistic dielectric properties in order to properly model human tissues. We have fabricated a low-water-content, low cost, mechanically and electrically stable, good shelf life and multi-layered heterogeneous phantom consisting of skin, fat and muscle tissues. We have chosen semi-solid type phantom for each tissue layer. The size and thickness of the each layer is chosen based on the average thickness of human tissue. Altering the ingredient composition wisely we can alter its dielectric properties also. By reason of no osmosis occurrence, the tissues can be employed to construct heterogeneous phantoms or even anthropomorphic phantoms without causing any changes in geometry or electrical properties. The performance of the fabricated phantom is carried out using an open-ended coaxial slim probe system by Agilent Technologies. Nearly all previous studies were based on very high frequency( VHF), so we present ultra-wide band (UWB), 500MHz-20GHz multilayered phantoms. We have measured our phantom after 2 month time period and we got quite good results for the dielectric properties without having significant variations. Thus, our fabricated sets of ATE phantom have good long lasting properties with good physical and dielectric stability.

Radio frequency (RF) and microwave switches are widely used in several different applications including radar, measurement systems, telecommunications, and other areas. An RF switch can control a radar’s transmit vs. receive mode, select the operating band, or direct an RF signal to different paths. In this study, a single pole eight throw (SP8T) switch using only Surface Mount (SMT) components is designed and simulated in Keysight’s Advanced Design System (ADS). Single pole eight throw is defined as one input and eight possible outputs. A star network configuration with series-shunt PIN diode switches is used to create the 8-way RF switch. There are other commercially available SP8T switches from MACOM, Skyworks, Analog Devices, and other vendors that operate around this bandwidth. However, this design uses SMT components and series-shunt diode configurations to create a device in the GHz range and power handling in the high 20 to 30 dBm range. This study modeled components in ADS, including the PIN diodes and the bias tees. The project also analyzed multiple layouts, finalizing the optimal design to meet specifications. The insertion loss, bandwidth, isolation, return loss, power handling, and switching speed are analyzed in the final design. Key specifications for this design are determined by comparing to other commercially available SP4T and SP8T switches from MACOM, Skyworks, Analog Devices, and other vendors, as well as developing an operational switch over the 2-18 GHz bandwidth. Additional specifications include limiting insertion loss to 2.0 dB maximum and maximizing isolation to 30 dB minimum. Switching speed and power handling specifications are also set to 20 ns and 23 dBm, respectively. Future projects will work on design fabrication and improvements to the manufactured switch.

Within the military there is great need for reliable communication between vehicles. During the planning and construction of a military RIB, Rigid-hulled Inflatable Boat, it is important to design an efficient antenna system that does not deteriorate out of disorder. It must also be ensured that the antennas transmitted power does not stay in the RIB boat. We have been given assignment to model and simulate a proposed antenna system and assess which tool is best suitable for the task. To analyze the antenna system we will look at the radiated electrical field together with the reflectionand EMC properties. The tool that we choose to use is a software called EMPro produced by Keysight Technologies. In this program we will create 3Dstructures for each individual object, the boat, the three antennas and the seawater. It’s also important to include each objects properties concerning material, so that they correctly reflect the reality. We are covering a broad spectrum with our antennas reaching from 1.6-30MHz, 30-88MHz and 100512MHz. The resulting simulation verifies that electromagnetic field would be powerful enough and that the antennas would not affect each other with the proposed placement. We could also confirm that our antennas reflected an inordinate amount of power but with cause that our models were not an exact replica of the antenna. The software EMPro is a suitable tool for this kind of projects concerning modeling and simulating antenna systems.Within the military there is great need for reliable communication between vehicles. During the planning and construction of a military RIB, Rigid-hulled Inflatable Boat, it is important to design an efficient antenna system that does not deteriorate out of disorder. It must also be ensured that the antennas transmitted power does not stay in the RIB boat. We have been given assignment to model and simulate a proposed antenna system and assess which tool is best suitable for the task. To analyze the antenna system we will look at the radiated electrical field together with the reflectionand EMC properties. The tool that we choose to use is a software called EMPro produced by Keysight Technologies. In this program we will create 3Dstructures for each individual object, the boat, the three antennas and the seawater. It’s also important to include each objects properties concerning material, so that they correctly reflect the reality. We are covering a broad spectrum with our antennas reaching from 1.6-30MHz, 30-88MHz and 100512MHz. The resulting simulation verifies that electromagnetic field would be powerful enough and that the antennas would not affect each other with the proposed placement. We could also confirm that our antennas reflected an inordinate amount of power but with cause that our models were not an exact replica of the antenna. The software EMPro is a suitable tool for this kind of projects concerning modeling and simulating antenna systems. / Inom militären finns stort behov av pålitlig kommunikation mellan fordon. Vid konstruktion av ett småfartyg i militärtoch bevakningssyfte är det viktigt att designa ett välfungerande antennsystem som inte försämras utav störningar, det ska även ses till att antennernas utsända effekt inte fastnar i småfartyget. Vi har fått en ritning av hur antennplaceringen är planerad, denna rapport går ut på att verifiera dess funktionalitet samt hitta en mjukvara som kan användas för att verifiera olika antennsystem. För att bedöma antennsystemet kommer denna rapport att undersöka att dess elektriska fält samt reflektionsoch EMC egenskaper, en uppgift som kan lösas med programvaran EMPro (Keysight). I programvaran skapas en 3Dstruktur som innehåller småfartyget, dess 3 stycken antenner samt omfattande havsvatten. Här tas hänsyn till objektens materialegenskaper, antennernas jordning samt de frekvenser antennerna arbetar på, 1.6-30MHz, 30-88MHz samt 100-512MHz. Simulering av systemet gav positiva resultat kring antennsystemets elektromagnetiskafält, antennerna kommer inte heller att störa varandra. Antennerna som vi har modellerat reflekterar orimligt mycket effekt, detta bortser vi från då vi inte haft tillgång till exakt avbildning av antennerna. EMPro är ett verktyg som är lämpligt att använda i detta samt liknande projekt. Dock krävs det att en kraftig dator finns tillgänglig då simuleringar av stora antennsystem baseras på stora uträkningar, som generellt tar lång tid.

The presented work describes the growing trend of using mobile devices to control laboratory instruments and displaying of measured data. The main objective is the application development for mobile devices, which will allow to remotely control and measure with laboratory instruments. The practical part is focused to programming mobile application which will be able by using the local network to connect multiple laboratory instruments, setting them for different types of measurements and then display measured data.