Global ETD Search

41	Energy storage and their combination with wind power compared to new nuclear power in Sweden : A review and cost analysis Englund-Karlsson, Simon January 2020 (has links) As intermittent renewable energy sources such as wind and solar power gradually increase around the world, older technologies such as nuclear power is phased out in Sweden and many other countries. It is then important to ensure that the total power need is secured, and that the power grid can remain stable. One way of managing intermittent renewables is by using energy storage. The main goal of this thesis was to compare energy storage methods and their costs. A secondary aim was to investigate how the cost of developing more renewable energy sources, in combination with different energy storage methods, compares to erecting new nuclear power. This thesis was limited to three energy storage technologies, namely pumped hydro storage (PHS), compressed air energy storage (CAES), and four battery storage technologies. They were combined with wind power in the cost analysis. The comparison was done by performing a literature review and economical calculations, which focused especially on levelized cost of storage (LCOS). The results from the economic calculations indicated that PHS and CAES had lower LCOS than battery storage technologies. Similar results could be seen in the literature review as well. When comparing levelized cost of energy (LCOE) nuclear power had the lowest, €0.03-0.12 kWh-1, followed by wind power in combination with PHS and CAES, both around €0.07-0.24 kWh-1. This result was maintained also at sensitivity analysis regarding the discount rate, which both nuclear power and PHS proved rather sensitive to. Keywords: energy storage, nuclear power, wind power, pumped hydro storage, compressed air energy storage, battery energy storage, levelized cost of energy, Sweden Energy storage wind power nuclear power levelized cost of energy levelized cost of storage review cost analysis LCOE LCOS pumped hydro storage compressed air energy storage battery storage PHS CAES Energy Systems Energisystem
42	EXPLORING THE POTENTIAL OF LOW-COST PEROVSKITE CELLS AND IMPROVED MODULE RELIABILITY TO REDUCE LEVELIZED COST OF ELECTRICITY Reza Asadpour (9525959) 16 December 2020 (has links) <div>The manufacturing cost of solar cells along with their efficiency and reliability define the levelized cost of electricity (LCOE). One needs to reduce LCOE to make solar cells cost competitive compared to other sources of electricity. After a sustained decrease since 2001 the manufacturing cost of the dominant photovoltaic technology based on c-Si solar cells has recently reached a plateau. Further reduction in LCOE is only possible by increasing the efficiency and/or reliability of c-Si cells. Among alternate technologies, organic photovoltaics (OPV) has reduced manufacturing cost, but they do not offer any LCOE gain because their lifetime and efficiency are significantly lower than c-Si. Recently, perovskite solar cells have showed promising results in terms of both cost and efficiency, but their reliability/stability is still a concern and the physical origin of the efficiency gain is not fully understood.</div><div><br></div>In this work, we have collaborated with scientists industry and academia to explain the origin of the increased cell efficiency of bulk solution-processed perovskite cells. We also explored the possibility of enhancing the efficiency of the c-Si and perovskite cells by using them in a tandem configuration. To improve the intrinsic reliability, we have investigated 2D-perovskite cells with slightly lower efficiency but longer lifetime. We interpreted the behavior of the 2D-perovskite cells using randomly stacked quantum wells in the absorber region. We studied the reliability issues of c-Si modules and correlated series resistance of the modules directly to the solder bond failure. We also found out that finger thinning of the contacts at cell level manifests as a fake shunt resistance but is distinguishable from real shunt resistance by exploring the reverse bias or efficiency vs. irradiance. Then we proposed a physics-based model to predict the energy yield and lifetime of a module that suffers from solder bond failure using real field data by considering the statistical nature of the failure at module level. This model is part of a more comprehensive model that can predict the lifetime of a module that suffers from more degradation mechanisms such as yellowing, potential induced degradation, corrosion, soiling, delamination, etc. simultaneously. This method is called forward modeling since we start from environmental data and initial information of the module, and then predict the lifetime and time-dependent energy yield of a solar cell technology. As the future work, we will use our experience in forward modeling to deconvolve the reliability issues of a module that is fielded since each mechanism has a different electrical signature. Then by calibrating the forward model, we can predict the remaining lifetime of the fielded module. This work opens new pathways to achieve 2030 Sunshot goals of LCOE below 3c/kWh by predicting the lifetime that the product can be guaranteed, helping financial institutions regarding the risk of their investment, or national laboratories to redefine the qualification and reliability protocols.<br> Solar Cell Solar Module Reliability Levelized Cost of Electricity LCOE Perovskite Solar Cells Ruddlesden-Popper Perovskite Tandem Solar Cell Bifaicial Solar Cell Contact Corrosion Contact Delamination Solder Bond Failure Dark Lock-in Thermography DLIT Markov Chain Method
43	Techno Economic study of Citizen Energy Communities among 5 case studies in the EU Nair, Archana Babu, Boteju, Senali January 2024 (has links) Energy communities are formed to create integrated regional energy market in EU and non- EU neighboring countries. It attracts investors in generation and energy networks as it comes up with new stable regulations, so that it will ensure the supply is stable and continuous. Five EU countries (Germany, Italy, Sweden, Greece, Austria) with different policies are selected and simulations are done. Economic analysis for the 5 countries is done based on simulation results. The selected 5 EU countries shows a good economic result; therefore, it can be recommended to implement energy communities and cities by developing the directives. By transposition of policies of the energy community and implementing more subsidies or incentive will make a better contribution for the citizen partnership for creating CEC. Energy Community Energy Directive Energy policies system sizing PVsyst simulation Subsidies/Incentives Economic Indicators Levelized cost of electricity (LCOE) Net Present Value (NPV) Simple Payback period Payback Period III Internal Rate of Return (IRR) Energy Engineering Energiteknik Energy Systems Energisystem
44	Analysis of a novel thermoelectric generator in the built environment Lozano, Adolfo 05 October 2011 (has links) This study centered on a novel thermoelectric generator (TEG) integrated into the built environment. Designed by Watts Thermoelectric LLC, the TEG is essentially a novel assembly of thermoelectric modules whose required temperature differential is supplied by hot and cold streams of water flowing through the TEG. Per its recommended operating conditions, the TEG nominally generates 83 Watts of electrical power. In its default configuration in the built environment, solar-thermal energy serves as the TEG’s hot stream source and geothermal energy serves as its cold stream source. Two systems-level, thermodynamic analyses were performed, which were based on the TEG’s upcoming characterization testing, scheduled to occur later in 2011 in Detroit, Michigan. The first analysis considered the TEG coupled with a solar collector system. A numerical model of the coupled system was constructed in order to estimate the system’s annual energetic performance. It was determined numerically that over the course of a sample year, the solar collector system could deliver 39.73 megawatt-hours (MWh) of thermal energy to the TEG. The TEG converted that thermal energy into a net of 266.5 kilowatt-hours of electricity in that year. The second analysis focused on the TEG itself during operation with the purpose of providing a preliminary thermodynamic characterization of the TEG. Using experimental data, this analysis found the TEG’s operating efficiency to be 1.72%. Next, the annual emissions that would be avoided by implementing the zero-emission TEG were considered. The emission factor of Michigan’s electric grid, RFCM, was calculated to be 0.830 tons of carbon dioxide-equivalent (CO2e) per MWh, and with the TEG’s annual energy output, it was concluded that 0.221 tons CO2e would be avoided each year with the TEG. It is important to note that the TEG can be linearly scaled up by including additional modules. Thus, these benefits can be multiplied through the incorporation of more TEG units. Finally, the levelized cost of electricity (LCOE) of the TEG integrated into the built environment with the solar-thermal hot source and passive ground-based cold source was considered. The LCOE of the system was estimated to be approximately $8,404/MWh, which is substantially greater than current generation technologies. Note that this calculation was based on one particular configuration with a particular and narrow set of assumptions, and is not intended to be a general conclusion about TEG systems overall. It was concluded that while solar-thermal energy systems can sustain the TEG, they are capital-intensive and therefore not economically suitable for the TEG given the assumptions of this analysis. In the end, because of the large costs associated with the solar-thermal system, waste heat recovery is proposed as a potentially more cost-effective provider of the TEG’s hot stream source. / text Thermoelectric generator TEG Novel thermoelectric generator Thermoelectrics Thermoelectric effect Thermoelectric modules Thermoelectric device Patent application Hot stream source Cold stream source EIA EERE Systems-level analysis Energy balance Control volume analysis Thermodynamic analysis Insolation data Insolation incident on a panel Incident insolation Extraterrestrial insolation NREL Ambient temperature data NOAA Renewable energy sources Energy generation technology Electricity generation technology Thermal energy Coupled system Emissions Greenhouse gas GHG Emissions analysis Zero-emission Emissions avoided Emission factor EF Reliability First Corporation RFC Built environment Integrated into the built environment Solar-thermal energy Solar collector system Photovoltaic thermal PVT panel Thermal storage tank Geothermal energy Geothermal heat pump GHP Ground source heat pump GSHP Numerical analysis Numerical model MATLAB Finite-difference Euler explicit Electric grid Annual energetic performance Annual electricity generation Operating efficiency System efficiency Thermodynamic characterization Economic analysis Levelized cost of energy LCOE Waste heat recovery Carbon dioxide equivalent CO2e Capital costs Installed costs Operating and maintenance costs

Page generated in 0.0268 seconds