The work presented in this dissertation is the first numerical investigation conducted to study leading edge film cooling with Large Eddy Simulation (LES). A cylindrical leading edge with a flat after-body represents the leading edge, where coolant is injected with a 30Ë compound angle. Three blowing ratios of 0.4, 0.8, and 1.2 are studied. Free-stream Reynolds number is 100,000 and coolant-to-mainstream density ratio is unity. At blowing ratio of 0.4, the effect of coolant inlet condition is investigated. Results show that the fully-turbulent coolant jet increases mixing with the mainstream in the outer shear layer but does not influence the flow dynamics in the turbulent boundary layer at the surface. As a result, the turbulent jet decreases adiabatic effectiveness but does not have a substantial effect on the heat transfer coefficient. At B.R.=0.4, three types of coherent structures are identified which consist of a primary entrainment vortex at the leeward aft-side of the coolant hole, vortex tubes at the windward side of the coolant hole, and hairpin vortices typical of turbulent boundary layers produced by the turbulent interaction of the coolant and mainstream downstream of injection. At B.R. = 0.8 and 1.2, coherent vortex tubes are no longer discernable, whereas the primary vortex structure gains in strength. In all cases, the bulk of the mixing occurs by entrainment which takes place at the leeward aft-side of the coolant jet. This region is characterized by a low pressure core and the primary entrainment vortex. Turbulent shear interaction between coolant jet and mainstream increases substantially with blowing ratio and contributes to the dilution of the coolant jet. As a result of the increased mixing in the shear layer and primary structure, adiabatic effectiveness decreases and heat transfer coefficient increases with increase in blowing ratio. The dissertation also investigates the deposition and erosion of Syngas ash particles in the film cooled leading edge region. Three ash particle sizes of 1, 5, and 10 microns are investigated at all blowing ratios using Lagrangian dynamics. The 1 micron particles with momentum Stokes number St = 0.03 (based on approach velocity and cylinder diameter), show negligible deposition/erosion. The 10 micron particles, on the other hand with a high momentum Stokes number, St = 3, directly impinge and deposit on the surface, with blowing ratio having a minimal effect. The 5 micron particles with St=0.8, show the largest receptivity to coolant flow and blowing ratio. On a mass basis, 90% of deposited mass is from 10 micron particles, with 5 micron particles contributing the other 10%. Overall there is a slight decrease in deposited mass with increase in blowing ratio. About 0.03% of the total incoming particle energy can potentially be transferred as erosive energy to the surface and coolant hole, with contribution coming from only 5 micron particles at B.R.=0.4 and 0.8, and both 5 and 10 micron particles at B.R.=1.2. / Ph. D.

Coal gasification and combustion can introduce contaminants in the solid or molten state depending on the gas clean up procedures used, coal composition and operating conditions. These byproducts when combined with high temperatures and high gas stream velocities can cause Deposition, Erosion, and Corrosion (DEC) of turbine components downstream of the combustor section. The objective of this dissertation is to use computational techniques to investigate the dynamics of ash deposition in a leading edge vane geometry with film cooling. Large Eddy Simulations (LES) is used to model the flow field of the coolant jet-mainstream interaction and the deposition of syngas ash in the leading edge region of a turbine vane is modeled using a Lagrangian framework. The three row leading edge vane geometry is modeled as a symmetric semi-cylinder with a flat afterbody. One row of coolant holes is located along the stagnation line and the other two rows of coolant holes are located at ±21.3° from the stagnation line. The coolant is injected at 45° to the vane surface with 90° compound angle injection. The coolant to mainstream density ratio is set to unity and the freestream Reynolds number based on leading edge diameter is 32000. Coolant to mainstream blowing ratios (B.R.) of 0.5, 1.0, 1.5, and 2.0 are investigated. It is found that the stagnation cooling jets penetrate much further into the mainstream, both in the normal and lateral directions, than the off-stagnation jets for all blowing ratios. Jet dilution is characterized by turbulent diffusion and entrainment. The strength of both mechanisms increases with blowing ratio. The adiabatic effectiveness in the stagnation region initially increases with blowing ratio but then generally decreases as the blowing ratio increases further. Immediately downstream of off-stagnation injection, the adiabatic effectiveness is highest at B.R.=0.5. However, in spite of the larger jet penetration and dilution at higher blowing ratios, the larger mass of coolant injected increases the effectiveness with blowing ratio further downstream of injection location. A novel deposition model which integrates different sources of published experimental data to form a holistic numerical model is developed to predict ash deposition. The deposition model computes the ash sticking probabilities as a function of particle temperature and ash composition. This deposition model is validated with available experimental results on a flat plate inclined at 45°. Subsequently, this model was then used to study ash deposition in a leading edge vane geometry with film cooling for coolant to mainstream blowing ratios of 0.5, 1.0, 1.5 and 2.0. Ash particle sizes of 5, 7, 10μm are considered. Under the conditions of the current simulations, ash particles have Stokes numbers less than unity of O(1) and hence are strongly affected by the flow and thermal fields generated by the coolant interaction with the main-stream. Because of this, the stagnation coolant jets are successful in pushing and/or cooling the particles away from the surface and minimizing deposition and erosion in the stagnation region. Capture efficiency for eight different ash compositions are investigated. Among all the ash samples, ND ash sample shows the highest capture efficiency due to its low softening temperature. A trend that is common to all particle sizes is that the percentage capture efficiency is least for blowing ratio of 1.5 as the coolant is successful in pushing the particles away from the surface. However, further increasing the blowing ratio to 2.0, the percentage capture efficiency increases as more number of particles are transported to the surface by strong mainstream entrainment by the coolant jets. / Ph. D.

Le développement de systèmes de propulsion alternatifs aux turboréacteurs actuels constitue un axe de recherche important dans le contexte aéronautique. L’open-rotor, moteur à hélices contrarotatives, constitue une piste sérieuse car il permet à la fois de réduire fortement la consommation de carburant et les émissions de gaz. Toutefois, les émissions sonores restent un défi pour ce type d’architecture, notamment du fait de l’absence de carénage. La compréhension des sources acoustiques et leur prévision est nécessaire afin de pouvoir, par la suite, réduire le bruit de ces moteurs. Les écoulements d’un doublet d’hélices contrarotatives sont complexes, en particulier pour l’hélice aval qui constitue l’axe d’étude de la thèse. Le travail présenté est dédié à une étude numérique, expérimentale et analytique et intervient dans le cadre de la chaire industrielle ADOPSYS entre Safran Aircraft Engines et l’Ecole Centrale de Lyon. L’objectif de ce travail est double. Il s’agit d’une part de réaliser une campagne expérimentale afin d’observer et de mieux comprendre le comportement de l’écoulement et de l’acoustique d’une pale en flèche, notamment en réponse à la présence d’un tourbillon de bord d’attaque. Un second objectif de la thèse était de constituer une base de données afin de comparer les prévisions obtenues avec un modèle analytique. Une méthode de calcul semi-analytique de la réponse aéroacoustique d’une pale aval en réponse à une excitation provenant de l’amont et prenant en compte les effets de charge et de géométrie a été développée. Une étude numérique d’un doublet d’hélices contrarotatives a servi de base à la définition de la géométrie de pale utilisée pendant l’étude. Celle-ci a été définie de façon à observer un tourbillon de bord d’attaque pour certains angles d’incidence. La maquette a ensuite été placée dans une soufflerie anéchoïque de l’Ecole Centrale de Lyon afin de réaliser une étude paramétrique. Des visualisations par enduit visqueux et des mesures de pression pariétale permettent de rendre compte de la présence du tourbillon de bord d’attaque à certains angles d’incidence. L’étude des spectres en champ lointain permet de distinguer un comportement en trois régimes, associés aux trois comportements du tourbillon de bord d’attaque. Des mesures de localisation de sources permettent de corroborer ces observations. Des prévisions analytiques du bruit émis par la pale et se basant sur le modèle d’Amiet ont également été réalisées. Dans un premier temps, les effets de la flèche sont pris en compte dans le modèle et celui-ci est alors appliqué à la pale de l’étude. Une meilleure adéquation des résultats est alors trouvée quand les effets de flèche sont pris en compte, en particulier dans les directions perpendiculaires à la pale. Le modèle est ensuite étendu afin de prendre en compte les effets de la jonction en pied de pale. Cette partie est exploratoire et le développement reste à approfondir. Un complément à l’expérience a consisté en l’étude de l’impact de sillages défilants sur la pale. Un système de barreaux rotatifs permet de générer des sillages périodiques représentatifs d’une interaction de sillages rotor-rotor. Les mesures réalisées montrent le comportement quasi-stationnaire du tourbillon. / The development of alternative propeller systems to turbojets is a main issue for research in the current context of aeronautical transport. Counter rotating open rotors are a candidate solution because they allow reduction of fuel consumption and gas emission. However, noise emissions are still a challenge for these types of configuration, in particular because they cannot benefit from the nacelle and the liners currently used in turbojet. The understanding of acoustic sources and their prediction is necessary in order to be able to reduce noise emission in the near future. Flows in an open-rotor are complex, in particular for the downstream propeller which is the subject of this approach.This work based on a numerical, experimental and analytical study and takes part in the ADOPSYS chair between Safran Aircraft Engines and l’Ecole Centrale de Lyon. This PhD has two main goals. The first one is to complete an experimental study in order to elucidate the behavior of the flow on a swept airfoil and the resulting acoustics, with a possibly developing leading-edge vortex. The measurements will be a data base for further comparison with analytical prediction. The second objective of the PhD consists in developing a semi-analytical modeling of the noise emitted by an airfoil in response to an incoming perturbation, taking into account the loading and geometry effects. A numerical study of a full counter-rotating system was used as a basis for designing the investigated airfoil. The latter was designed so that a leading-edge vortex could be formed on the surface for some angles of attack. The mock-up was then tested in an anechoic wind tunnel of Ecole Centrale de Lyon for various sets of parameters. Flow visualization and wall-pressure measurements indicated the presence of the leading-edge vortex for some angles of attack. The far-field measurements indicated three acoustic regimes, which can be associated with three behaviors of the leading-edge vortex. Source localization measurements corroborate these observations. Analytical predictions of the noise emitted by the airfoil and based on Amiet’s model were also performed. Firstly, the sweep angle is taken into account in the model. Secondly it is applied to the studied airfoil. A better match of the results is found when the sweep is considered, in particular in the perpendicular directions. The model in then extended in order to include the wall-junction. This part is exploratory and should be further developed. Finally, a complementary experimental investigation of the impingement of periodic wakes on the airfoil has been performed, using a system made of rotating bars, mimics true wake interactions. The measurements suggest that the leading-edge vortex has a quasi-steady behavior.

The epidermis is the first barrier of protection of living organisms against external attacks. It is constantly renewed throughout life, through a process called "homeostasis", which ensures that every cell lost on its surface is replaced by new ones. Recent studies have shown that this balance is ensured by a hierarchy of stem cells (SC) and progenitors that perform 3 types of cell divisions, each having a fixed probability. Although the epidermis has been extensively studied during homeostasis, little is known about the cellular dynamics taking place when the epidermis must expand its surface. Are these probabilities of division immutable or can they change? In this project, we focused on two conditions of epidermal expansion: postnatal growth and wound healing. Using the mouse tail epidermis as a model, we show that the re-epithelialization after a wound is achieved via the formation of two transient compartments that are spatially and molecularly distinct :a leading edge and a proliferative hub. We show that the leading edge cells have a specific transcriptional signature that is independent of their quiescent state and we propose new markers not previously described. Using the technique of "lineage tracing", coupled with clonal analysis and mathematical modeling, we highlight the proliferation dynamics of SCs and progenitors during healing. We show that different populations of cells residing in different compartments, the hair follicle infundibulum and the interfollicular epidermis, acquire a similar dynamics and re-activate their SC while the progenitors increase their rate of proliferation without changing their division probabilities. This similar proliferation dynamics in two compartments of the epidermis suggests that division probabilities are not dictated by the cell of origin. Interestingly, cell dynamics is different during postnatal growth. Using lineage tracing, clonal analysis and single-cell transcriptional analysis, we demonstrate that the post-natal epidermis is composed of a homogeneous population of equipotent progenitors which ensure a harmonious tissue growth through a constant imbalance towards self-renewing divisions and an ever decreasing proliferation rate. On the other hand, we show that basal cells in the adult epidermis display a greater molecular heterogeneity and that this heterogeneity is acquired progressively at the end of growth. Finally, by coupling in vivo measurements and in vitro micro-patterning experiments, we show that the orientation of cell division of equipotent progenitors is locally influenced by the alignment of the collagen fibers of the underlying dermis. These data suggest that SC specification occurs late in postnatal development and that proliferation dynamics are not immutable and could therefore be influenced by extrinsic factors. / L’épiderme est la première barrière de protection des organismes vivants contre des attaques extérieures. Il est constamment renouvelé au cours de la vie, via un processus appelé « homeostasie », qui assure que chaque cellule perdue à sa surface soit remplacée par de nouvelles. Des études récentes ont montré que cet équilibre était assuré par une hiérarchie de cellules souches (CS) et de progéniteurs qui réalisent 3 types de divisions cellulaires, chaque type de division ayant une probabilité fixe. Bien que l’épiderme ait été intensivement étudié durant l’homeostasie, peu de choses sont connues concernant la dynamique cellulaire prenant place lors de phénomènes où l’épiderme doit grandir. Ces probabilités de division sont-elles immuables ou peuvent-elles au contraire changer ?Dans ce projet, nous nous sommes intéressés à deux conditions d’expansion de l’épiderme :la croissance post-natale et la cicatrisation des plaies. En utilisant l’épiderme de la queue de souris comme modèle, nous montrons que la ré-épithélialisation d’une plaie est réalisée via la formation de deux compartiments cellulaires transitoires distincts spatialement et du point de vue moléculaire :un front de migration et un centre prolifératif. Nous montrons que les cellules du front de migration ont une signature transcriptionnelle spécifique qui est indépendante de leur état de quiescence et proposons de nouveaux marqueurs non décrits auparavant. En utilisant la technique du « lineage tracing », couplée à une analyse clonale et à de la modélisation mathématique, nous mettons en évidence la dynamique de prolifération des CS et des progéniteurs lors de la cicatrisation. Nous montrons que différentes populations de cellules résidant dans des compartiments différents, l’infundibulum du follicule pileux et l’épiderme interfolliculaire, acquièrent une dynamique similaire et ré-activent leur CS tandis que les progéniteurs augmentent leur taux de prolifération sans changer leur probabilité de division. Cette dynamique de prolifération similaire dans deux compartiments de l’épiderme suggère que les probabilités de divisions ne sont pas dictées par la cellule d’origine. De façon intéressante, la dynamique cellulaire est par contre différente durant la croissance post-natale. En utilisant le lineage tracing, l’analyse clonale et des analyses transcriptionnelles sur cellule unique, nous démontrons que l’épiderme post-natal est composé d’une population homogène de progéniteurs équipotents qui présentent un constant déséquilibre envers des divisions d’auto-renouvèlement et un taux de prolifération décroissant, assurant une croissance harmonieuse de l’épiderme. En revanche, les cellules basales de l’épiderme adulte montrent une plus grande hétérogénéité moléculaire et cet hétérogénéité est acquise progressivement à la fin de la croissance. Enfin, en couplant des mesures in vivo et des expériences de micro-patterning in vitro, nous montrons que l’orientation de la division cellulaire des progéniteurs équipotents est localement influencée par l’alignement des fibres de collagène du derme sous-jacent. Ces données suggèrent que la spécification des CS survient tardivement au cours du développement post-natal et que la dynamique de prolifération n’est pas immuable et pourraient donc être influencée par des facteurs extrinsèques. / Doctorat en Sciences biomédicales et pharmaceutiques (Pharmacie) / info:eu-repo/semantics/nonPublished

Cette thèse fait partie du projet beyond the sea® qui a pour but de développer la traction par cerf-volant à boudins gonflés (kite) comme système de propulsion auxiliaire des navires. Comme le kite est une structure souple, il est nécessaire de mettre en place une boucle d’interaction fluide-structure pour calculer la géométrie du kite en vol et ses performances aérodynamiques. Un modèle de Ligne Portante 3D Non-Linéaire a été développé pour pouvoir gérer ces ailes non planes, avec des angles de dièdre et de flèche qui varient le long de l’envergure, et également pour pouvoir prendre en compte la non-linéarité du coefficient de portance de la section aérodynamique. Le modèle a été vérifié par des simulations RANSE sur différentes géométries et donne des résultats satisfaisants pour des angles d’incidence et de dérapage variant jusqu’à 15°, avec des différences relatives de quelques pour cent pour l’estimation de la portance globale de l’aile. Les résultats locaux sont aussi correctement estimés, le modèle est capable d’estimer la position du minimum et du maximum de chargement local, selon l’envergure de l’aile, et cela même pour une aile en dérapage. En parallèle, un modèle structure a été développé. L’idée principale du modèle Kite as a Beam est de réduire le kite à un ensemble d’éléments poutre, chacun équivalent à une partie du kite composé d’une section du boudin d’attaque, de deux lattes gonflées et de la canopée correspondante. Le modèle Kite as a Beam a été comparé à un modèle éléments finis complet du kite sur des cas de déplacements élémentaires. Les résultats montrent certaines différences de comportement entre les deux modèles, avec notamment une surestimation de la raideur en torsion pour le modèle Kite as a Beam. Finalement, le modèle Kite as a Beam a été couplé avec la Ligne Portante 3D Non-Linéaire, puis comparé au modèle éléments finis, couplé également avec la Ligne Portante. La réduction du temps de calcul est réellement importante mais les résultats de la comparaison montrent la nécessité de calibrer le modèle Kite as a Beam pour pouvoir retrouver correctement les résultats du modèle éléments finis. / The present thesis is part of the beyond the sea® project which aims to develop tethered kite systems as auxiliary devices for ship propulsion. As a kite is a flexible structure, fluid-structure interaction has to be taken into account to calculate the flying shape and aerodynamic performances of the wing. A 3D Non-Linear Lifting Line model has been developed to deal with non-straight kite wings, with dihedral and sweep angles variable along the span and take into account the non-linearity of the section lift coefficient. The model has been checked with 3D RANSE simulations over various geometries and produces satisfactory results for range of incidence and sideslip up to 15°, with typical relative differences of few percent for the overall lift. The local results are also correctly estimated, the model is able to predict the position of the minimum and maximum loading along the span, even for a wing in sideslip. Simultaneously, a structure model has been developed. The core idea of the Kite as a Beam model is to approximate a Leading Edge Inflatable kite by an assembly of beam elements, equivalent each to a part of the kite composed of a portion of the inflatable leading edge, two inflatable battens and the corresponding canopy. The Kite as a Beam model has been compared to a complete kite Finite Element model over elementary comparison cases. The results show the behaviour differences of the two models, for example the torsion stiffness is globally overestimated by the Kite as a Beam model. Eventually, the Kite as a Beam model coupled with the 3D Non-Linear Lifting Line model is compared to the complete finite element model coupled with the 3D Non-Linear Lifting Line model. The gain in computation time is really significant but the results show the necessity of model calibration if the Kite as a Beam model should be used to predict the results of the complete finite element model.

Oscillating-foil hydrokinetic turbines have gained interest over the years to extract energy from renewable sources. The influence of the sweep angle on the performance of a fully-passive oscillating-plate hydrokinetic turbine prototype was investigated experimentally in the present work. The sweep angle was introduced to promote spanwise flow along the plate in order to manipulate the leading edge vortex (LEV) and hydrodynamically optimize the performance of the turbine. In the present work, flat plates of two configurations were considered: a plate with a 6° sweep angle and an unswept plate (control), which were undergoing fully-passive pitch and heave motions in uniform inflow at the Reynolds numbers ranging from 15 000 to 30 000. The resulting kinematic parameters and the energy extraction performance were evaluated for both plates. Planar (2D) particle image velocimetry (PIV) was used to obtain patterns of the phase-averaged out-of-plane vorticity during the oscillation cycle. The circulation in the wake was then related to the induced-forces on the plate by calculating the moments of vorticity of the LEV with respect to the pitching axis of the plate. Tomographic (3D) PIV was implemented in evaluating the influence of the spanwise flow on the dynamics of the vortex structure in three-dimensional space. The rate of deformation of the vortex length was quantified by calculating the deformation terms embedded in the vorticity equations, then linked to the stability of the vortex. The results show evidence of delay of the shedding of LEV and increased vortex stability, in the case of the swept plate. The manipulation of the LEV by the spanwise flow was related to the induced kinematics exhibited by the prolonged heave forces experienced by the swept plate, which led to the higher power extraction performance at high inflow velocities. In the presence of spanwise flow, positive vortex stretching along the vortex line increased the stabilization of the vortex core and prevented the onset of helical vortex breakdown, observed in the case of the unswept plate. The use of the sweep profile on the plate has led to the improvement of energy extraction performance of the fully-passive hydrokinetic turbine. / Graduate

Cette thèse concerne l’aérodynamique de pales d'extrémité transsonique. Ces pales sont conçues pour maximiser le rendement en croisière, tout en générant la traction requise au décollage. Elles ont des profils fins et peu cambrés, travaillant à forte incidence au décollage, ce qui peut entraîner l’apparition d’un tourbillon de bord d’attaque (TBA). Or ce TBA présente des similitudes avec les tourbillons d’apex d’aile Delta, connus pour leur capacité à générer de la portance tourbillonnaire.Cette étude consiste à examiner l’intérêt du TBA pour les performances aérodynamiques.La démarche a consisté dans un premier temps à caractériser la topologie du TBA sur une maquette représentative d’une pale d’ Open Rotor, à l'aide d'essais PIV résolus en temps et de calculs RANS k-omega SST, et à évaluer la capacité de la simulation RANS à reproduire les caractéristiques d’intérêt pour cette étude. Un algorithme a été développé afin d'estimer la contribution de ce TBA à la portance à partir du champ de pression pariétal RANS.Afin d'expliciter l'influence des paramètres géométriques et de fonctionnement de la pale sur la portance tourbillonnaire, un modèle 1D de la portance tourbillonnaire a été développé puis couplé à la méthode de l'élément de pale.Les premières comparaison de géométries à iso-traction ont montré que la portance tourbillonnaire permet de générer la traction requise au décollage avec une surface alaire plus faible. Ces résultats ouvrent de nouvelles perspectives pour la conception de géométries avec un meilleur rendement en croisière. / This thesis deals with the aerodynamic properties of propeller blades. Those blades are designed to maximise cruise efficiency, while achieving the target thrust at take-off. Their thin, low-cambered profiles must work at high incidence at take-off, which may give rise to a leading-edge vortex (LEV).The topology of this LEV looks similar to Delta wing LEVs, which are known to generate vortex lift.the aim of this study is to explore the probable impact of the LEV on lift at take-off in order to reconsider propeller blade designs. The approach first consisted in caracterising the LEV topology on a model blade representative of an Open Rotor front blade, using both Time-Resolved PIV and RANS k-omega SST calculations. The comparison between both methods demonstrated the ability of RANS calculations to reproduce the LEV characteristics of interest to this study.Then, the LEV contribution to lift was evaluated thanks to an algorithm developed to estimate vortex lift contribution from RANS wall pressure fields.In order to explicit the influence of the blade's geometrical and functioning parameters on vortex lift, a 1D vortex lift model was developed and coupled to the Blade Element Momentum Theory.The first blade geometry comparative studies at iso-thrust showed that vortex lift enables to generate target thrust at take-off with a lower blade surface. This opens new perspectives for the design of blade geometries with enhanced cruise efficiency.

Small-scale wind turbines were not considered viable in the past due to their poor efficiencies, mainly because of their aerodynamic effects around the irfoil shape. Recently researchers have renewed interest in enhancing the aerodynamic performances of the blades’ designs inspired by the aerodynamic pattern of biological characteristics of insects and marine mammals such as locusts, dragonflies, damselflies, Humpback Whales etc. Bioinspired wing designs have advantages compared to conventional smooth irfoil blades as they can counter the bending forces that the wings experience during flapping. Bio-inspired corrugated airfoil based on dragonfly wing geometries have been reported to perform well compared to conventional airfoil at low Reynolds numbers. Corrugated airfoils reduce flow separation and enhance aerodynamic performance by trapping vortices in the corrugations thus drawing flow towards the airfoil’s surface. This results in the higher lift whilst incurring only marginally higher drag. Such airfoils also have an advantage when it comes to span-wise structural stiffness due to the corrugated cross-sections. Replacing conventional turbine blades by tubercles or corrugated blades could enhance turbine performance by reducing the pressure gradient along the leading edge; however, the aerodynamic effects at the leading edge will depend on the variations of wavelength and amplitude. In this study, two types of computational studies were investigated: Optimising a corrugated airfoil and investigating the aerodynamic effects of a sinusoidal shape at the leading edge of a blade. Previous studies used an idealized geometry based on the dragonfly wing cross-section profile but did not attempt to optimize the geometry. In the present study: a two-dimensional CFD model is constructed using ANSYS Fluent Workbench-Design Explorer to determine the optimal corrugated blade profile for four angles of attack (AOA) from 5° to 20° corresponding to typical AOA of small-scale wind turbine blades. Two modified blades with variations of wavelength and amplitude at the leading edge were studied to investigate the aerodynamic effects. Three-dimensional models were constructed using Qblade software and 3D points were exported to AutoCAD Inventor to generate the CAD model. The governing equations used are continuity and Navier-Stokes equations written in a frame reference rotating with the blade. The CFD package used is ANSYS FLUENT 19.0. The simulation was run under steady-state, using SST-k omega turbulence model. The modifications have improved the aerodynamic performance. The optimised corrugated blade produced a maximum increase of CL and L/D. Both modified blades (1 and 2) had their performances measured separately and compared to that of baseline blade SG6042 (Conventional blade). Modified blade 1 had a lower wavelength and amplitude at the leading edge of 14.3 % and 4 % respectively of the chord. It was noted that the aerodynamic performance decreased by 6%. Modified model 2, on the other hand had a higher wavelength and amplitude at the leading edge. of 40.4 % and 11.9 % respectively of the chord. It was also noted the aerodynamic performance increased by 6%. From the empirical evidence highlighted above, it can be observed that there is a direct correlation between wavelength, amplitude, and aerodynamic performance of the blade. / Electrical and Mining Engineering / M. Tech. (Engineering)

There is currently a great deal of interest within the aviation community in the design of small, slow-flying but manoeuvrable uninhabited vehicles for reconnaissance, surveillance, and search and rescue operations in urban environments. Inspired by observation of birds, insects, fish and cetaceans, flapping wings are being actively studied in the hope that they may provide greater propulsive efficiencies than propellers and rotors at low Reynolds numbers for such Micro-Air Vehicles (MAVs). Researchers have posited the Strouhal number (combining flapping frequency, amplitude and forward speed) as the parameter controlling flapping wing aerodynamics in cruising flight, although there is conflicting evidence. This thesis explores the effect of flapping frequency and amplitude on forces and wake structures, as well as physical mechanisms leading to optimum propulsive efficiency. Two-dimensional rigid airfoils are considered at Reynolds number 2,000 ??? 40,000. A compressible Navier-Stokes simulation is combined with numerical and analytical potential flow techniques to isolate and evaluate the effect of viscosity, leading and trailing edge vortex separation, and wake vortex dynamics. The wake structures of a plunging airfoil are shown to be sensitive to the flapping frequency independent of the Strouhal number. For a given frequency, the wake of the airfoil exhibits ???vortex lock-in??? as the amplitude of motion is increased, in a manner analogous to an oscillating circular cylinder. This is caused by interaction between the flapping frequency and the ???bluff-body??? vortex shedding frequency apparent even for streamlined airfoils at low Reynolds number. The thrust and propulsive efficiency of a plunging airfoil are also shown to be sensitive to the flapping frequency independent of Strouhal number. This dependence is the result of vortex shedding from the leading edge, and an interaction between the flapping frequency and the time for vortex formation, separation and convection over the airfoil surface. The observed propulsive efficiency peak for a pitching and plunging airfoil is shown to be the result of leading edge vortex shedding at low flapping frequencies (low Strouhal numbers), and high power requirements at large flapping amplitudes (high Strouhal numbers). The efficiency peak is governed by flapping frequency and amplitude separately, rather than the Strouhal number directly.

Direct numerical simulations of the receptivity and instability of boundary layers on flat and curved surfaces are herein reported. Various flow models are considered with the aim to capture aspects of flows over straight and swept wings such as wall curvature, pressure variations, leading-edge effects, streamline curvature and crossflow. The first model problem presented, the flow over a swept flat plate, features a crossflow inside the boundary layer. The layer is unstable to steady and traveling crossflow vortices which are nearly aligned with the free stream. Wall roughness and free-stream vortical modes efficiently excite these crossflow modes, and the associated receptivity mechanisms are linear in an environment of low-amplitude perturbations. Receptivity coefficients for roughness elements with various length scales and for free-stream vortical modes with different wavenumbers and frequencies are reported. Key to the receptivity to free-stream vorticity is the upstream excitation of streamwise streaks evolving into crossflow modes. This mechanism is also active in the presence of free-stream turbulence. The second flow model is that of a Görtler boundary layer. This flow type forms on surfaces with concave curvature, e.g. the lower side of a turbine blade. The dominant instability, driven by a vertically varying centrifugal force, appears as pairs of steady, streamwise counter-rotating vortical rolls and streamwise streaks. The Görtler boundary layer is in particular receptive to free-stream vortical modes with zero and low frequencies. The associated mechanism builds on the excitation of upstream disturbance streaks from which the Görtler modes emerge, similar to the mechanism in swept-plate flows. The receptivity to free-stream vorticity can both be linear and nonlinear. In the presence of free-stream turbulence, nonlinear receptivity is more likely to trigger steady Görtler vortices than linear receptivity unless the frequencies of the free-stream fluctuations are very low. The third set of simulations considers the boundary layer on a flat plate with an elliptic leading edge. This study aims to identify the effect of the leading edge on the boundary-layer receptivity to impinging free-stream vortical modes. Three types of modes with streamwise, vertical and spanwise vorticity are considered. The two former types trigger streamwise disturbance streaks while the latter type excites Tollmien-Schlichting wave packets in the shear layer. Simulations with two leading edges of different bluntness demonstrate that the leading-edge shape hardly influences the receptivity to streamwise vortices, whereas it significantly enhances the receptivity to vertical and spanwise vortices. It is shown that the receptivity mechanism to vertical free-stream vorticity involves vortex stretching and tilting - physical processes which are clearly enhanced by blunt leading edges. The last flow configuration studied models an infinite wing at 45 degrees sweep. This model is the least idealized with respect to applications in aerospace engineering. The set-up mimics the wind-tunnel experiments carried out by Saric and coworkers at the Arizona State University in the 1990s. The numerical method is verified by simulating the excitation of steady crossflow vortices through micron-sized roughness as realized in the experiments. Moreover, the receptivity to free-stream vortical disturbances is investigated and it is shown that the boundary layer is most receptive, if the free-stream modes are closely aligned with the most unstable crossflow mode / QC 20101025