Thesis deals with the issue of lighting technology control using wireless technology. Thesis includes a description of current possibilities of control light technology, methods of digital signal transmission using radio waves and protocols dealing with this issue are described. This thesis also contains a park aimed at the selection of suitable electronic components including the design of individual electronic blocks and printed circuit board. The conclusion of the thesis is the realization of electronic modules, including the creation of module software and measurement of achieved parameters under real conditions.

This master’s thesis deals with design and construction of a system for repote measurement of air quality in buildings. The first section provides a selection and analysis of used hardware and software components: minicomputer Raspberry Pi, STM32F401 microcontroller, communication module XBee-Pro, CO2 sensor and also communication interfaces IC and USART. The next section includes a design of electrical wiring, circuit board, configuration of the wireless modules and a software implementation for microcontroller and the concentrator.

This thesis describes designing of a wireless system which allows to transmit measured data of sensors made of smart concrete. Measured data are transmitted from measuring points to the collecting unit, which stores them, and pass them to the server which is connected in the Internet network. The design of the system is focused to achieve low power consumption of all used components to provide the longest possible operation time, when using primary lithium cell. The design should be also able to provide possibility of easy modification of the measuring points.

This thesis is focused on the design of the antenna to a specific application XY. Emphasis is placed on a narrow antenna beam width, which will ensure full-fledged profit for the tag directly below the antenna. This thesis presents a total of five proposals that could be used by XY application. This thesis also presents the results of field measurements, which confirm the improved characteristics of the antenna with parasitic patch.

A need for a quantitative method to determine body water level has been identified by a team of Clinical Innovation Fellows at the Centre for Technology in Medicine and Health (CTMH). A reliable way to determine body water level would bring great benefits to the healthcare sector, where no optimal method is available at the time of writing. A possible solution is a sensor that would measure alterations in skin properties due to changes in total body water. CTMH has had an idea of such a sensor, which is evaluated in this work. At an early stage of this evaluation process, it became clear that the research regarding correlations between skin properties and body hydration level was not sufficient to warrant the initiation of a sensor development process. Therefore, the main objective of this thesis became to investigate such correlations. An extensive literature review is presented, from which an experiment was developed. The experiment was performed on four human test subjects and involved measurements of skin thickness and elasticity parameters, before and after a weight loss of 3.2-3.7 % due to dehydration. The results showed clear decreases in skin thickness and indications of alterations in skin distensibility as well as in the skin’s immediate elastic response to applied negative pressure. It could also be seen that skin at different body sites does not respond in the same way - calves showed more distinct results than thighs and volar forearm. The material provided in this thesis encourages further studies of the correlation between the mentioned properties and total body water. If a predictable correlation can be found, a sensor development process could start. A reliable way to determine body water level would bring great benefits to the healthcare sector, where no optimal method is available at the time of writing. / Ett behov av att kvantitativt kunna mäta kroppens vattennivå har identifierats av Clinical Innovation Fellowship vid Centrum för Teknik i Medicin och Hälsa (CTMH). Ett tillförlitligt sätt att mäta kroppens vattennivå skulle gynna hälso- och sjukvården på många sätt då ingen optimal metod är tillgänglig i dagsläget. En möjlig lösning skulle kunna vara en sensor som mäter variationer i hudegenskaper till följd av förändringar i kroppens vattennivå. CTMH har haft en idé om en sådan sensor, vilken utvärderas i detta arbete. I ett tidigt skede av utvärderingsprocessen framkom det tydligt att tillräcklig forskning saknades gällande korrelationer mellan hudens egenskaper och kroppens vattennivå. Det huvudsakliga syftet med detta masterexamensarbete blev därför att undersöka sådana korrelationer. En omfattande litteraturgransking gjordes, och utifrån denna utformades ett experiment. Experimentet utfördes på fyra testpersoner och innefattade mätningar av hudens tjocklek samt elasticitetsparameterar. Dessa utfördes före och efter viktnedgång av 3,2-3,7 % till följd av vattenförlust. Resultaten visade på en tydlig minskning av hudtjockleken samt indikationer på förändringar av hudens tänjbarhet samt dess omedelbara elastiska respons vid pålagt negativt tryck. Det visade sig också att huden inte reagerar på samma sätt på olika kroppsdelar - vader visade tydligare förändringar jämfört med lår och armar. Det material som presenteras i detta examensarbete uppmuntrar till fortsatt utredning av korrelationer mellan de nämnda hudegenskaperna och kroppens vattennivå. Om det går att förutse korrelationer finns det förutsättningar för att påbörja utveckling av en sensor.

No description available.

Electromagnetic compatibility (EMC) is an essential part in today’s society and there are more products around us that emit electromagnetic waves than ever before. To make sure that all these products function properly under all circumstances EMC testing is needed. One test that is conducted is radiated immunity testing. A susceptibility antenna is needed to perform immunity testing. This thesis aims to show that a tuneable antenna could be used for immunity testing in the frequency band 26-150 MHz and in the future replace the current antenna, which is not tuneable, used at SAAB Support and Services EMC in Östersund. A simulation program called EZNEC+ was used to simulate different antennas that were tested in the semi-anechoic chamber at SAAB. Two antenna types showed better efficiency and reached lower in frequency than SAAB’s current antenna. These antennas were a bowtie antenna and an x-shaped antenna, both extending in only two spacial directions instead of the normal three. Their drawback was a less uniform E-field at the lowest frequencies, where the E-field was much stronger to the sides compared to straight in front of the antenna. This results in a narrow lobe width, but if this drawback could be accepted or mitigated both antennas are possible replacements for the current antenna at SAAB and should be further investigated.

<p>This thesis describes the implementation of a real-time, full search, 16x16 bidirectional motion estimation at 24 frames per second with the record performance of 155 Gop/s (1538 ops/pixel) at a high clock rate of 125 MHz. The core of bidirectional motion estimation uses close to 100% FPGA resources with 7 Gbit/s bandwidth to external memory. The architecture allows extremely controlled, macro level floor-planning with parameterized block size, image size, placement coordinates and data words length. The FPGA chip is part of the board that was developed at the Institute of Computer & Communication Networking Engineering, Technical University Braunschweig Germany, in collaboration with Grass Valley Germany in the FlexFilm research project. The goal of the project was to develop hardware and programming methodologies for real-time digital film image processing. Motion estimation core uses FlexWAFE reconfigurable architecture where FPGAs are configured using macro components that consist of weakly programmable address generation units and data stream processing units. Bidirectional motion estimation uses two cores of motion estimation engine (MeEngine) forming main data processing unit for backward and forward motion vectors. The building block of the core of motion estimation is an RPM-macro which represents one processing element and performs 10-bit difference, a comparison, and 19-bit accumulation on the input pixel streams. In order to maximize the throughput between elements, the processing element is replicated and precisely placed side-by-side by using four hierarchal levels, where each level is a very compact entity with its own local control and placement methodology. The achieved speed was further improved by regularly inserting pipeline stages in the processing chain.</p>

This thesis describes the implementation of a real-time, full search, 16x16 bidirectional motion estimation at 24 frames per second with the record performance of 155 Gop/s (1538 ops/pixel) at a high clock rate of 125 MHz. The core of bidirectional motion estimation uses close to 100% FPGA resources with 7 Gbit/s bandwidth to external memory. The architecture allows extremely controlled, macro level floor-planning with parameterized block size, image size, placement coordinates and data words length. The FPGA chip is part of the board that was developed at the Institute of Computer &amp; Communication Networking Engineering, Technical University Braunschweig Germany, in collaboration with Grass Valley Germany in the FlexFilm research project. The goal of the project was to develop hardware and programming methodologies for real-time digital film image processing. Motion estimation core uses FlexWAFE reconfigurable architecture where FPGAs are configured using macro components that consist of weakly programmable address generation units and data stream processing units. Bidirectional motion estimation uses two cores of motion estimation engine (MeEngine) forming main data processing unit for backward and forward motion vectors. The building block of the core of motion estimation is an RPM-macro which represents one processing element and performs 10-bit difference, a comparison, and 19-bit accumulation on the input pixel streams. In order to maximize the throughput between elements, the processing element is replicated and precisely placed side-by-side by using four hierarchal levels, where each level is a very compact entity with its own local control and placement methodology. The achieved speed was further improved by regularly inserting pipeline stages in the processing chain.

This diploma thesis deals with optimization of transmitter amplifier parameters for LoRaWAN network. The issue of optimization is first based on the conditions of ETSI EN 300 220, which takes into account the eventuality of interference the adjacent channels in the band. The optimizations are designed specifically for the Qorvo RF5110g integrated circuit, so that the amplifier meets the requirements of the above standard at the limit of the maximum allowed output power and also with respect to radio ecology.