N,N′-methylenebisacrylamide-crosslinked poly(N-isopropylacrylamide), also known as P(NIPAM), was developed as a fluid delivery system for use with microfluidic paper-based analytical devices (microPADs). MicroPADs are postage-stamp-sized devices made out of paper that can be used as platforms for low-cost, simple-to-use point-of-care diagnostic assays. P(NIPAM) is a thermally responsive polymer that absorbs aqueous solutions at room temperature and will expel the solutions to microPADs when heated. The fluid delivery characteristics of P(NIPAM) were assessed, and P(NIPAM) was able to deliver multiple solutions to microPADs in specific sequences or simultaneously in a laminar-flow configuration. P(NIPAM) was then shown to be suitable for delivering four classes of reagents to microPADs: small molecules, enzymes, antibodies and DNA. P(NIPAM) successfully delivered a series of standard concentrations of glucose (0 – 5 mM) to microPADs equipped to perform a colorimetric glucose assay. The results of these tests were used to produce an external calibration curve, which in turn was used to determine accurately the concentrations of glucose in sample solutions. P(NIPAM) successfully delivered fluorescein-labeled IgG and fluorescein-labeled oligonucleotides (20 base pairs) to microPADs in a variety of concentrations. P(NIPAM) also successfully delivered horseradish peroxidase (HRP) to microPADs, and it was determined that HRP could be stored in P(NIPAM) for 35 days with minimal loss in activity. The combination of P(NIPAM) with microPADs will allow for more complex assays to be performed with minimal user input, will facilitate the preparation of external calibration curves in the field, and may be useful in extending the shelf life of microPADs by stabilizing reagents.

Development of silicon based electronics have revolutionized our every day life during the last three decades. Nowadays Si based devices operate close to their theoretical limits that is becoming a bottleneck for further progress. In particular, for the growing field of high frequency and high power electronics, Si cannot offer the required properties. Development of materials capable of providing high current densities, carrier mobilities and high breakdown fields is crucial for a progress in state of the art electronics. Epitaxial graphene grown on semi-insulating silicon carbide substrates has a high potential to be integrated in the current planar device technologies. High electron mobilities and sheet carrier densities make graphene extremely attractive for high frequency analog applications. One of the remaining challenges is the interaction of epitaxial graphene with the substrate. Typically, much lower free charge carrier mobilities, compared to free standing graphene, and doping, due to charge transfer from the substrate, is reported. Thus, a good understanding of the intrinsic free charge carriers properties and the factors affecting them is very important for further development of epitaxial graphene. III-group nitrides have been extensively studied and already have proven their high efficiency as light sources for short wavelengths. High carrier mobilities and breakdown electric fields were demonstrated for III-group nitrides, making them attractive for high frequency and high power applications. Currently, In-rich InGaN alloys and AlGaN/GaN high electron mobility structures are of high interest for the research community due to open fundamental questions. Electrical characterization techniques, commonly used for the determination of free charge carrier properties, require good ohmic and Schottky contacts, which in certain cases can be difficult to achieve. Access to electrical properties of buried conductive channels in multilayered structures requires modification of samples and good knowledge of the electrical properties of all electrical contact within the structure. Moreover, the use of electrical contacts to electrically characterize two-dimensional electronic materials, such as graphene, can alter their intrinsic properties. Furthermore, the determination of effective mass parameters commonly employs cyclotron resonance and Shubnikov-de Haas oscillations measurements, which require long scattering times of free charge carriers, high magnetic fields and low temperatures. The optical Hall effect is an external magnetic field induced optical anisotropy in  conductive layers due to the motion of the free charge carriers under the influence of the Lorentz force, and is equivalent to the electrical Hall effect at optical frequencies. The optical Hall effect can be measured by generalized ellipsometry and provides a powerful method for the determination of free charge carrier properties in a non-destructive and contactless manner. In principle, a single optical Hall effect measurement can provide quantitative information about free charge carrier types, concentrations, mobilities and effective mass parameters at temperatures ranging from few kelvins to room temperature and above. Further, it was demonstrated that for transparent samples, a backside cavity can be employed to enhance the optical Hall effect. Measurement of the optical Hall effect by generalized ellipsometry is an indirect technique requiring subsequent data analysis. Parameterized optical models are fitted to match experimentally measured ellipsometric data by varying physically significant parameters. Analysis of the optical response of samples, containing free charge carriers, employing optical models based on the classical Drude model, which is augmented with an external magnetic field contribution, provide access to the free charge carrier properties. The main research results of the graduate studies presented in this licentiate thesis are summarized in the five scientific papers. Paper I. Description of the custom-built terahertz frequency-domain spectroscopic ellipsometer at Linköping University. The terahertz ellipsometer capabilities are demonstrated by an accurate determination of the isotropic and anisotropic refractive indices of silicon and m-plane sapphire, respectively. Further, terahertz optical Hall effect measurements of an AlGaN/GaN high electron mobility structures were employed to extract the two-dimensional electron gas sheet density, mobility and effective mass parameters. Last, in-situ optical Hall effect measurement on epitaxial graphene in a gas cell with controllable environment, were used to study the effects of environmental doping on the mobility and carrier concentration. Paper II. Presents terahertz cavity-enhanced optical Hall measurements of the monolayer and multilayer epitaxial graphene on semi-insulating 4H-SiC (0001) substrates. The data analysis revealed p-type doping for monolayer graphene with a carrier density in the low 1012 cm−2 range and a carrier mobility of 1550 cm2/V·s. For the multilayer epitaxial graphene, n-type doping with a carrier density in the low 1013 cm−2 range, a mobility of 470 cm2/V·s and an effective mass of (0.14 ± 0.03) m0 were extracted. The measurements demonstrate that cavity-enhanced optical Hall effect measurements can be applied to study electronic properties of two-dimensional materials. Paper III. Terahertz cavity-enhanced optical Hall effect measurements are employed to study anisotropic transport in as-grown monolayer, quasi free-standing monolayer and quasi free-standing bilayer epitaxial graphene on semi-insulating 4H-SiC (0001) substrates. The data analysis revealed a strong anisotropy in the carrier mobilities of the quasi freestanding bilayer graphene. The anisotropy is demonstrated to be induced by carriers scattering at the step edges of the SiC, by showing that the mobility is higher along the step than across them. The scattering mechanism is discussed based on the results of the optical Hall effect, low-energy electron microscopy, low-energy electron diffraction and Raman measurements. Paper IV. Mid-infrared spectroscopic ellipsometry and mid-infrared optical Hall effect measurements are employed to determine the electron effective mass in an In0.33Ga0.67N epitaxial layer. The data analysis reveals slightly anisotropic effective mass and carrier mobility parameters together with the optical phonon frequencies and broadenings. Paper V. Terahertz cavity-enhanced optical Hall measurements are employed to study the free charge carrier properties in a set of AlGaN/GaN high electron mobility structures with modified interfaces. The results show that the interface structure has a significant effect on the free charge carrier mobility and that the sample with a sharp interface between an AlGaN barrier and a GaN buffer layers exhibits a record mobility of 2332±73 cm2/V·s. The determined effective mass parameters showed an increase compared to the GaN value, that is attributed the the penetration of the electron wavefunction into the AlGaN barrier layer.

Carbon fiber (CF) is predominantly produced from fossil-based sources and is therefore an area of interest for further development towards a more sustainable society. The purpose of this thesis work was to investigate the possibility of producing precursor fibers (PFs) for CF production from a blend of renewable cellulose andlignin. Cellulose, which is used to some extent for CF production, was chosen, while the possibility of adding lignin was investigated in hope of increasing the gravimetric yield of the CF production. Blends of softwood kraft cellulose pulp (SKP) and softwood kraft lignin (SKL) were dissolved in an alkaline (NaOH) solvent system at different cellulose/lignin ratios. A total of eight dopes were prepared (SKP/SKL ratios of 100/0–60/40 wt./wt.) with total dope concentrations ranging from 4.5 wt.% to 9.2 wt.%. The addition of SKL resulted in dark colored dopes with viscosities of which mainly appeared to depend on the SKP concentration. The dopes were wet spun, resulting in continuously spun PFs. The PFs showed on an increasing pyrolysis yield with increased SKL content but decreasing mechanical properties. However, process optimization was not included in the work, subsequently leading to the assumption that greater values on mechanical properties can be achieved. A pure SKP PF and a SKP-SKL (70/30 wt./wt.) PF were successfully thermally converted into CFs by carbonization at 1000 °C. The PF containing SKL had a total gravimetric yield more than twice as high as the pure SKP PF, 28 wt.% and 12 wt.%, respectively. Thereby, the addition of SKL seems to have a positive impact on the CF yield when utilizing a NaOH(aq) solvent system. This thesis work has become a base for the future work towards the development of CFs from wet spun cellulose-lignin PFs in the NaOH(aq) solvent system.

Electrosorption-based capacitive deionization (CDI) has become a viable process for brackish water desalination and defluoridation. In this study, activated Douglas fir biochar is used as a low-cost electrode material with adsorption capacity comparable to activated carbon obtained from biomass precursors. Adding functional groups to the activated biochar enhanced salt removal capacity, providing cation and anion selectivity. The functionalized electrodes were prepared by Nafion, titanium isopropoxide, and p-phenylenediamine treatment, respectively, which introduced sulfonate, titanium dioxide and amine functional groups to the electrode surface. These modification methods are versatile and can be easily performed without sophisticated laboratory environment. Modified biochar electrodes were characterized by TEM, SEM-EDX, XRD, and XPS. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were performed to analyze the electrochemical properties of the electrodes. The salt adsorption capacity (SAC) was evaluated in a 3D-printed capacitive deionization flow cell using a chloride and fluoride ion sensor. It was found that functionalized biochar electrodes had increased SAC and charge efficiency in asymmetrical setup due to reduced co-ion effect. For example, the asymmetrical CDI cell with Nafion cathode and amine biochar anode improved NaCl removal capacity by 54% over the activated biochar symmetrical cell (identical anode and cathode), with SAC 6.01 mg NaCl/g biochar at the symmetrical cell and 9.25 mg/g for the asymmetrical cell. The charge efficiency also increased by ≈ 67% from symmetric AcB cell to asymmetric TB-05 cathode and AmB anode. This work shows that biochar can be engineered and explored broadly as an inexpensive sustainable electrode material for asymmetrical capacitive deionization.

Transparenta papper tillverkade av cellulosa nanofibriller (CNF), visar stor potential att kunna ersätta petroleumbaserade plaster inom många användningsområden, till exempel för mat- och varuförpackningar. CNF, även känt som nanocellulosa, kombinerar viktiga cellulosaegenskaper, med unika egenskaper hos nanomaterial. Denna kombination av egenskaper möjliggör tillverkning av ett pappers-liknande material som uppvisar både utmärkta mekaniska egenskaper och hög transparens. Användningen av nanocellulosa är dock förknippad med diverse utmaningar, för att materialet ska kunna bli kommersiellt slagkraftigt. En av de främsta utmaningarna är nanocellulosas höga affinitet för vatten och dess höga specifika yta som försvårar hanteringen av materialet. Avvattningen av nanocellulosadispersioner, för att tillverka transparenta papper, kan ta upp till flera timmar. För att övervinna detta hinder, har avdelningen för Fiberteknologi vid KTH tillsammans med BillerudKorsnäs AB, nyligen utvecklat en metodik för att skapa så kallade själv-fibrillerande fibrer (SFFer). Dessa fibrer möjliggör en snabbavvattnad papperstillverkningsprocess med makroskopiska vedbaserade fibrer, som efter tillverkning av pappret omvandlas till ett nanocellulosapapper, det vill säga ett nanopapper. För att erhålla SFFer krävs det att höga koncentrationer av karboxyl- och aldehydgrupper introduceras i cellulosafibrerna. Införandet av dessa funktionella grupper, möjliggör självfibrilleringen då SFFerna utsätts för moderata alkali-koncentrationer. I den ursprungliga studien som utfördes av Gorur m.fl., introducerades de funktionella grupperna med hjälp av sekventiell TEMPO- och periodatoxidation. I detta examensarbete, har alternativa kemiska metoder för att introducera samma kemiska funktionalitet som TEMPO-periodatsystemet undersökts. Huvudsyftet med arbetet är att besvara frågan: Hur påverkar olika kemiska behandlingar vid SFF tillverkningen, de kemiska och fysikaliska egenskaperna hos de modifierade fibrerna, samt de slutgiltiga pappersegenskaperna? För att besvara frågan, preparerades fibrer med liknande karboxyl- och aldehydinnehåll med hjälp av följande tre kemiska metoder: 1) TEMPO- följd av periodatoxidation (detta kommer att användas som referenssystem); 2) periodat- följd av kloritoxidation; 3) karboxymetylering följd av periodatoxidation. Egenskaperna hos fibrerna undersöktes med avseende på aldehyd- och karboxylinnehåll, avvattningspotential och förmåga att självfibrillera. Papper tillverkades med hjälp av en vakuumfiltreringsuppställning och följande egenskaper undersöktes hos pappret: mekaniska egenskaper (dragstyrka, brottsyrka och Young’s modul); optiska (transparens och ytreflektion); samt syrgaspermeabilitet. De erhållna fibrerna från samtliga tre kemiska modifieringar visade på självfibrillerande egenskaper i alkaliska lösningar. Detta beteende styrker hypotesen att ett strategiskt införande av ett högt karboxyl- och aldehydinnehåll leder till självfibrillerande fibrer. Transparenta papper tillverkade av fibrer som utsatts för TEMPO-periodatoxidation samt klorit-periodatoxidation, visade på utmärkta mekaniska egenskaper, hög transparens och bra barriäregenskaper - jämförbara med vad som vanligen kan noteras hos papper tillverkat av nanocellulosa. Samtliga egenskaper förbättrades ytterligare efter fibrillering av fibrerna i papperen. De karboxymetylerade-periodatoxiderade materialet, å andra sidan, uppvisade andra egenskaper jämfört med de två, tidigare nämnda, metoderna. TEMPO-periodat- och periodat-klorit-pappersmassan var halvgenomskinlig och geléliknande, medan den karboxymetylerade-periodatoxiderade massan var mer lik det omodifierade materialet. Detsamma gällde det tillverkade pappret som liknade ett konventionellt papper. Det var inte heller möjligt att åstadkomma en fibrillering av det karboxymetylerade-periodatoxiderade-pappret som utsattes för behandling med alkaliska lösningar. Avvattningstiden vid papperstillverkningen varierad mellan 4 och 60 sekunder, och karboxymetylering-periodat oxidation visade på snabbast avvattningstid. Den förlängda avvattningstiden i jämförelse med studien utförd av Gorur m.fl., tros främst bero på att ett filtreringsmembran med mindre porer användes på vakuumfiltreringsuppställningen, istället för en avvattningsvira som tidigare använts. Sammanfattningsvis så har det visat sig möjligt att tillverka självfibrillerande fibrer med hjälp av samtliga tre undersökta kemiska modifieringar. SFFer möjliggör tillverkning av snabbavvattnade transparenta nanocellulosapapper och visar på så vis på hög potential att kunna ersätta olje-baserade plaster till många förpackningsapplikationer. / Transparent papers made from cellulose nanofibrils (CNF), derived from e.g. wood, show great potential to replace petroleum-based plastics in many application areas, such as packaging for foods and goods. CNF, also known as nanocellulose, combine important cellulose properties with the unique features of nanoscale materials, gaining paper-like materials with outstanding mechanical properties and high transparency. However, nanocellulose faces various challenges in order to make the products commercially competitive. One of the main challenges is accompanied with nanocelluloses’ high affinity for water, which makes processing difficult. Dewatering of a nanocellulose dispersion in order to produce transparent paper may take up to several hours. To overcome this obstacle, the Fibre technology division at KTH Royal Institute of technology and BillerudKorsnäs AB have recently developed a new concept of self-fibrillating fibres (SFFs). This material enables fast-dewatering papermaking using fibres of native dimensions and conversion into nanocellulose after the paper has been prepared. In order to obtain SFFs, proper amounts of charged groups and aldehyde groups need to be introduced into the cellulose backbone. When SFFs are exposed to high alkali concentration, i.e. > pH=10, the fibres self-fibrillates into CNFs. In the original study, the functional groups were introduced through sequential TEMPO oxidation and periodate oxidation. In this work, alternative chemical routes have been examined to prepare SFFs with the same functional groups as introduced with the TEMPO-periodate system. The aim of the thesis has been to answer: how does different chemical routes to prepare transparent nanopaper made from SFFs affect the chemical and physical properties of the modified fibres, as well as the final physical properties of the transparent papers? To answer the question, fibres with similar carboxyl and aldehyde contents were prepared using three chemical routes: 1) TEMPO oxidation followed by periodate oxidation (which was used as reference system); 2) periodate oxidation followed by chlorite oxidation; 3) carboxymethylation followed by periodate oxidation. The properties of the fibres were examined regarding aldehyde and carboxyl content, dewatering potential and self-fibrillating ability. Papers were produced using a vacuum filtration set-up and the properties investigated were the mechanical; tensile strength, strain at failure and Young’s modulus, the optical properties; transparency and haze, as well as the oxygen permeability. In order to investigate the impact of the fibrillation of the papers, the properties were measured for both unfibrillated and fibrillated samples. Furthermore, the gravimetric yield after each chemical modification procedure was examined, as well as the dewatering time during sheet making. Fibres obtained from all three chemistries demonstrated self-fibrillating properties in alkaline solutions. This strengthens the hypothesis that the strategical introduction of aldehydes and carboxyl groups is the main feature responsible for the self-fibrillating ability of the fibres. Transparent papers made from fibres treated through TEMPO-periodate oxidation and periodate-chlorite oxidation showed excellent mechanical, optical and barrier properties, comparable to those seen in nanocellulose papers. The properties were further increased after fibrillation. The carboxymethylated-periodate oxidized fibres, on the other hand, behaved differently from the others. While the TEMPO-periodate and periodate-chlorite pulp was semi-translucent and gel-like, the carboxymethylated-periodate oxidized fibres resembled more the unmodified material. Likewise, the properties of those papers resembled conventional paper and no fibrillationwas experienced after immersing the papers in alkaline solution, according to the same protocol developed for the other two chemistries. The dewatering time during sheet making ranged from 4–60 seconds (carboxymethylation-periodate oxidation showing the fastest dewatering rates). The increased dewatering time compared to earlier studies is believed to mainly be due to the use of a filtration membrane on the vacuum filtration set-up, instead of a metallic wire with larger pores. Overall, SFFs was successfully produced using three different chemical routes. SFFs enables production of fast-dewatering transparent nanocellulose papers that shows the potential to replace oil-based plastics in many packaging applications.

Perovskit solceller (PSCs) är kända som 'ljusomvandling' enheter med ökad omvandlingseffektivitiet (PCE). PSCs är kända för detta flexibilitet och hög tolerans mot defekter och består av fem lager med olika material och egenskaper. De fem lagren är följande; transparant elektrod, elektron ledande lager (ETL), perovskit lager, hål ledande lager (HTL) och metallelektroden.  Detta forskningsarbete fokuserar på metallelektroden (Cu-tunn film), HTL (CuI-tunn film) och det aktiva lagret (CuI-komplex).  Syftet med denna studie är att undersöka effekten av olika tjocklekar på ytans morfologi och grovhet för att se mängden jod som tränger sig genom filmen genom att beräkna volymen.  Resultatet av denna studie visar att ökad tjocklek leder till ökad grovhet. Man ser även att en ökad tjocklek leder till ett mer homogent och jämn yta, och dessutom ökar kornstorleken, vilket tyder på att kvaliten av kristallisationen förbättras.  Slutligen, genom att känna till tjockleken och storleken (arean) på ytan av proverna kunde man beräkna volymen för att indikera mängden jod som trängt sig genom filmen. Resultatet av denna del indikerade att ju tjockare provet är, desto mer kommer jod att tränga sig genom filmen. / Perovskite solar cells (PSCs) are known as light-harvesting devices with increased power conversion efficiencies (PCE). PSCs are known for their flexibility and high tolerance towards defects. It consists of five different layers with different materials and functions. Transparent electrode, electron transport layer (ETL) , perovskite or active layer , hole transport layer (HTL) and metallic electrode. In this research project, the focus is directed towards the metallic electrode (Cu-thin film), hole transport layer (CuI-thin film) and the active layer (CuI-complex). The purpose of this study is to investigate the effect of different thicknesses on the surface morphology and roughness and to see how much iodine is diffusing through the film by calculating the volume.  The results of this project present that the increase in thickness leads to an increase in roughness. It also shows that an increase in thickness leads to a more homogeneous and uniform surface and in addition the grain size increases which indicates that the quality of crystallization improves. Finally, by knowing the thickness and surface area of the samples the volume was calculated to indicate how much iodine is diffusing through the film and the results for this part indicated that the thicker the sample, more iodine will diffuse through the film.

<p>This thesis presents studies of the X-ray linear dichroism (XLD) in individual single-walled (SW) and multi-walled (MW) carbon nanotubes (CNT) measured by a scanning transmission X-ray microscope (STXM). The C 1s spectra of CNT showed a large XLD at the C 1s→π* transition. The magnitude of the XLD was found to be related to the quality of CNT such that in high quality CNT, it was fairly large and as the quality lowered it decreased. This dichroic effect was used to map defects along individual CNT. In addition, STXM was employed to map chemical components in pristine, purified, and dodecyl functionalized SWCNT bundles to investigate the changes occurring in them due to chemical functionalization.<br />STXM has limited spatial resolution. Thus, electron energy loss spectroscopy (EELS) in a transmission electron microscope (TEM) was used to obtain similar information about CNT, but at much higher spatial resolution. The measurements performed in the scanning transmission electron microscopy (STEM) mode produced signals analogous to the XLD when the orientation of the momentum transfer (q) was resolved. This was achieved by displacing the pattern of electron scattering from CNT relative to the EELS entrance aperture. TEM-EELS was also utilized to map defects in pristine and focused ion beam (FIB) modified CNT.</p> / Doctor of Philosophy (PhD)

<p>This thesis is the result of several experiments designed to probe the low temperature physics underlying the 1D-Ising-like behaviour of chains of spins in the structure of Cobalt Niobate, CoNb2O6. A collection of prior work has been done by several groups prior to this, focusing on mapping the phase diagram above 0.5K. Interest in this material was renewed recently based upon theoretical work and experimental confirmation of the unique structure of the spins in the system. The bulk of this work was done at temperatures below the previously investigated range to probe the unique properties of this system.</p> <p>The material was grown at McMaster University using the optical floating zone technique from oxide powders. The crystal was examined and oriented using single crystal and Laue diffraction and was cut for use in further experiments. Squid magnetometry was used to confirm the material properties and phase transition temperatures, and was compared to literature values.</p> <p>Heat capacity measurements were performed locally down to 2K, and by collaborators at Waterloo in the range from 330mK to 1K. The heat capacity measurement confirmed the 2.9K transition and explored the relaxation time of the material. Cobalt niobate was found to have an exceptionally long relaxation time at low temperatures indicating strong spin-spin interactions. A sharp transition with zero applied field was found to become a broad, smooth feature at 2.9K when a small field was applied.</p> <p>We performed muSR measurements in zero, longitudinal and transverse field. The muSR results confirmed the long relaxation time found by the heat capacity measurements, which may reflect the coupling of the spin system to the lattice. Additionally, the material was never seen to statically order in zero or longitudinal field down to 700mK and up to 1T. The material was found to behave dynamically throughout all the field ranges.</p> / Master of Science (MSc)

<p>Thermoelectric (TE) materials are able to convert heat directly into electricity and vice versa. This special property makes them valuable for a variety of applications involving power generation and refrigeration. In the search for potential high-performance TE materials, a number of rare-earth (<em>RE</em>) antimonide suboxide phases have been investigated.This presentation will focus on two classes of rare-earth antimonide suboxides: the <em>RE</em>₃Sb₃O₃ and <em>RE</em>₈Sb_3-<em>_d</em>O₈ phases (<em>C</em>2/<em>m</em> space group) based on the <em>RE</em>–O frameworks and the <em>anti</em>-ThCr₂Si₂ type <em>RE</em>₂SbO₂ compounds (<em>I</em>4/<em>mmm</em> space group). The physical property measurements on the high-purity bulk samples revealed unexpected semiconducting properties in the non-charge-balanced systems, i.e.<em> RE</em>₈Sb_3-<em>_d</em>O₈ and <em>RE</em>₂SbO₂. Since the electronic structure calculations suggest that the anionic Sb states dominate the valence band at the vicinity of the Fermi level, the local structure of the Sb atomic site is believed to dictate the observed physical properties. The charge transport properties are explained within the framework of Anderson/Mott-type localizations. Ultimately, systematic investigation of the <em>RE</em>₂SbO₂ and Ho₂Sb_1-<em>x</em>Bi<em>_x</em>O₂ series reveal the large variability of the electrical properties caused by the local structural perturbations.</p> / Doctor of Philosophy (PhD)

<p>The goal of this research project is to synthesize, characterize, and examine the properties of a material that undergoes a decrease in refractive index upon exposure to light. It is anticipated that such photoresponses could elicit previously unknown nonlinear phenomena including self-trapped black beams. An appropriate material for these investigations would be a polymer cross-linked by photocleavable groups causing a Δ<em>n</em> < 0. Organo-ditellurides, molecules that contain a Te-Te bond, would be appropriate for the crosslinks as their σ*_Te-Te ← n_Te transition usually absorbs light between 400 and 500 nm, and can lead to photodissociation of the chalcogen-chalcogen bond.</p> <p>Initial attempts to directly functionalize a polymer (polystyrene) resulted in intractable solids. A more promising approach relies on the preparation of cross-linking agents followed by co-polymerization. Despite literature claims, to date, there is no structurally authenticated photoresponsive molecule that simultaneously contains vinyl (CH=CH) and telluride (-Te-) functional groups. The work in this thesis has yielded what would be the first example, in addition to a crystal structure obtained by X-ray diffraction, the compound has been characterized by multinuclear NMR (¹H, ¹³C, ¹²⁵Te) and vibrational spectroscopy with the support of DFT calculations.</p> / Master of Science (MSc)