DC system and DC microgrids are gaining popularity in recent times. This thesis suggests a method to state the workability of a DC based PV system using the softwares Simulink, PVsyst and HOMER. The aims of this project include suggesting a DC based architecture, finding out the performance ratio and a cost analysis. The advantages of the DC based system, the cost benefits associated with it and its performance will determine its feasibility.   Not many softwares have the functionality to simulate DC based PV systems. PVsyst is considered as one of the most sought-out softwares for the simulation of PV systems. It can simulate a DC based PV system but has a lot of limitations when it comes to the architecture and voltage levels. Due to these factors, the results from softwares Simulink, Homer and PVsyst are used to calculate the performance ratio of the suggested DC system.    The simulation of the DC system involves modelling of a DC-DC converter. DC-DC converters are used in HVDC transmission and are being considered for small scale and medium scale microgrids. The DC-DC boost converter is coupled with a MPPT model in Simulink. P and O algorithm is chosen as the MPPT algorithm as it is simple and widely used. The Simulink model of PV array and MPPT based boost converter provides the power output at the needed voltage level of 350V. The input for the Simulink model is obtained from the results of HOMER. The inputs include solar irradiation data and cell temperature. The same input data is used for the simulations in HOMER and PVsyst. The performance ratio is obtained by combining the power output from Simulink with the other aspects of the system from PVsyst. The performance ratio is done only for the month of January due to the limitations in Simulink. The performance ratio is found out to be 65.5 %.   The cost estimation is done for the distribution and power electronics aspects of the system. It is found out that the cost associated with the conductors will have an impact on the total cost only if the conductors used for distribution is more in length. The cost associated with the power converters will make a difference in total cost only if the system is within the range of 100kW. The study shows the workability of the PV based DC system based on the above mentioned aspects

Renewable power systems are becoming more affordable and provide better options than fossil-fuel generation, for not only the environment, but a benefit of a reduced cost of operation. Methods to optimize charging batteries from renewable technologies is an important subject for off-grid and micro-grids, and is becoming more relevant for larger installations. Overcharging or undercharging the battery can result in failure and reduction of battery life. The Arduino hybrid MPPT controller takes the advantage of solar and wind energy sources by controlling two systems simultaneously. The ability to manage two systems with one controller is better for an overall production of energy, cost, and manageability, at a minor expense of efficiency. The hybrid MPPT uses two synchronous buck DC-DC converters to control both wind and solar. The hybrid MPPT performed at a maximum of 93.6% efficiency, while the individual controller operated at a maximum 97.1% efficiency when working on the bench test. When designing the controller to manage power production from a larger generator, the inductor size was too large due to the frequency provided by the Arduino. A larger inductor means less allowable current to flow before the inductor becomes over saturated, reducing the efficiency of the controller. Utilizing a different microcontroller like the PIC16C63A produces a much faster frequency, which will reduce the inductor size needed and allow more current before over saturation.

This master’s thesis is an introduction to switching mode power supplies, especially focused on digital control. It summarizes the basic topologies of switching mode power supplies, and discusses the fundamental issues of digital power supply control. It also summarizes basic informations about Piccolo microcontrolers, about experimental kit and about main parts of sample source code. Also is described here own implementation of the control law and the theory and implementation of maximum power point tracking. The conclusion of this thesis deals with implemantation a testing of the designed digitally controled switching power supply.

The aim of this work is construction of mobile phone which can be build using com- ponents that are widely available. The concept allows control of mobile communication in GSM network on AT commands level. Energy saving is emphasised and alternative power source using solar cell is examined. Manufacturing data and docummentation is available for user.

This diploma thesis deals with a design layout of the fan power supply that ensures the increase of the efficiency of the heating unit. For usage in the areas without electric power, the power supply is secured by thermoelectric generator. The system has to function on the basis of autonomous system which turns itself on only when necessary. In the introductory part of the paper there is a recherché of thermoelectric generators for general usage. Next it mentions the basic findings in from the field of DC/DC converters for low power applications. In this part attention is given to MPPT algorithm. Furthermore basic knowledge from the field of heat transmission together with its most used elements is described. Subsequently existing applications that increase the effectiveness of heating are mentioned. Their disadvantage however is that they depend on the external source of power supply. The practical part to a large extent covers the analysis of the suitability of the chosen thermoelectric module. For securing of the heat gradient of the generator there was a model created meeting the figures in the manual and there are several simulations in the MATLAB program. Furthermore several measurements of the thermoelectric module took place in order to secure realistic figures. Subsequently a DC/DC converter was chosen. Finally the testing was made on the real composition. In conclusion there is an overall evaluation including the real usage and the economical aspect of the project. The outcomes of the work enable to avoid common mistakes that are part of many specialized articles. The created system is to be used after the adjustment of the cooling to the required aim. At the same time it becomes very effective.

Tato diplomová práce se zabývá vývojem autonomního zdroje elektrické energie založeného na MEMS termoelektrickém generátoru. Uvažovaný generátor bude následně použit pro napájení autonomní senzorické jednotky pro letecké aplikace. Systémový pohled na autonomní senzorickou jednotku zahrnuje senzor se zpracováním a přenosem dat, energy harvester (termoelektrický generátor), power management, akumulační prvek a autodiagnostiku. Všechny výše uvedené komponenty jsou v práci podrobně popsány. V úvodu práce je provedena široká rešerše existujících termoelektrických generátorů pro letecké aplikace. Následně jsou popsány základní teoretické poznatky z oblasti DC/DC měničů pro energy harvesting. Zvláštní pozornost je věnována metodám MPPT (Maximum Power Point Tracking). Jako základ pro vývoj napájení autonomní senzorické jednotky bylo provedeno množství simulací za pomoci nástroje MATLAB/Simulink Simscape. Pro identifikaci prametrů modelu posloužilo měření na speciálním přípravku. Praktická implementace teoreticky popsaných problémů je provedena na k tomuto účelu navrženém technologickém demonstrátoru. Závěrem je zhodnocena reálná využitelnost navržené technologie pro finální aplikaci v leteckém průmyslu.

No description available.

The necessity for clean and sustainable energy has shifted the energy sector’s interest in renewable energy sources. Photovoltaics (PV) is the most popular renewable energy source because the sun is ubiquitous. However, several discrepancies exist in a PV system when implemented for real-world applications. Among several other existing problems related to Photovoltaics, in this work, we deal with maximum power point tracking (MPPT) under Partial Shading (PS) conditions. MPPT is a mechanism formulated as an optimization problem adjusting the PV to deliver the maximum power to the load. Under full insolation conditions, varying solar panel temperatures, and different loads MPPT problem is a convex optimization problem. However, when the PV’s surface is partially shaded, multiple power peaks are created in the power versus voltage (P-V) curve making MPPT non-convex.

This thesis presents an optimal method of designing and controlling an oscillating energy harvesting system. Many new and emerging energy harvesting systems, such as the energy harvesting backpack and ocean wave energy harvesting, capture energy normally expelled through mechanical interactions. Often the nature of the system indicates slow system time constants and unsteady AC voltages. This paper reveals a method for achieving maximum energy harvesting from such sources with fast determination of the optimal operating condition. An energy harvesting backpack, which captures energy from the interaction between the user and the spring decoupled load, is presented in this paper. The new control strategy, maximum energy harvesting control (MEHC), is developed and applied to the energy harvesting backpack system to evaluate the improvement of the MEHC over the basic maximum power point tracking algorithm.

In recent years, wind energy technology has become one of the top areas of interest for energy harvesting in the power electronics world. This interest has especially peaked recently due to the increasing demand for a reliable source of renewable energy. In a recent study, the American Wind Energy Association (AWEA) ranked the U.S as the leading competitor in wind energy harvesting followed by Germany and Spain. Although the United States is the leading competitor in this area, no one has been able successfully develop an efficient, low-cost AC/DC convertor for low power turbines to be used by the average American consumer. There has been very little research in low power AC/DC converters for low to medium power wind energy turbines for battery charging applications. Due to the low power coefficient of wind turbines, power converters are required to transfer the maximum available power at the highest efficiency. Power factor correction (PFC) and maximum power point tracking (MPPT) algorithms have been proposed for high power wind turbines. These turbines are out of the price range of what a common household can afford. They also occupy a large amount of space, which is not practical for use in one's home. A low cost AC/DC converter with efficient power transfer is needed in order to promote the use of cheaper low power wind turbines. Only MPPT is implemented in most of these low power wind turbine power converters. The concept of power factor correction with MPPT has not been completely adapted just yet. The research conducted involved analyzing the effect of power factor correction and maximum power point tracking algorithm in AC/DC converters for wind turbine applications. Although maximum power to the load is always desired, most converters only take electrical efficiency into consideration. However, not only the electrical efficiency must be considered, but the mechanical energy as well. If the converter is designed to look like a purely resistive load and not a switched load, a wind turbine is able to supply the maximum power with lower conduction loss at the input side due to high current spikes. Two power converters, VIENNA with buck converter and a Buck-boost converter, were designed and experimentally analyzed. A unique approach of controlling the MPPT algorithm through a conductance G for PFC is proposed and applied in the VIENNA topology. On the other hand, the Buck-boost only operates MPPT. With the same wind profile applied for both converters, an increase in power drawn from the input increased when PFC was used even when the power level was low. Both topologies present their own unique advantages. The main advantage for the VIENNA converter is that PFC allowed more power extraction from the turbine, increasing both electrical and mechanical efficiency. The buck-boost converter, on the other hand, presents a very low component count which decreases the overall cost and volume. Therefore, a small, cost-effective converter that maximizes the power transfer from a small power wind turbine to a DC load, can motivate consumers to utilize the power available from the wind.