<p>  </p> <p>With rising concerns over commercial aviation’s contribution to global carbon emissions, there exists a tremendous pressure on the aviation industry to find advanced technological solutions to reduce its share of CO2 emissions. Single-aisle (or narrowbody) aircraft are the biggest contributors to CO2 emissions by number of operations, insisting a need to reduce / eliminate their aircraft-level fuel consumption as soon as possible. A potential solution for this is to operate fully-electric single-aisle aircraft; however, the limitations of the current (and predicted future) battery technology is forcing the industry to explore hybrid-electric aircraft as a possible mid-term solution.</p> <p>Modeling hybrid-electric aircraft comes with its own challenges due to the presence of two different propulsion sources – gas turbine engines (powered by Jet-A fuel) and electric motors (powered by batteries). Since traditional sizing approaches and legacy sizing tools do not seem to work well for hybrid-electric aircraft, this work presents a “flight-mechanics-based” conceptual sizing tool for hybrid-electric aircraft, set up as a Multidisciplinary Design Optimization (MDO) toolbox. Some of the key features of the sizing tool include concurrently sizing the electric motors and downsizing the gas turbine engines while meeting the one-engine-inoperative (OEI) and top-of-climb constraints, and re-sizing the fuselage to account for the volumetric constraints associated with required batteries.</p> <p>Current work considers a parallel hybrid-electric single-aisle aircraft with a 900 nmi design range, with electric power augmentation (with electric motors operating at full throttle) available only for the takeoff and climb segments when sizing the aircraft. Four hybrid-electric propulsion technology cases are considered, and the resulting hybrid-electric aircraft show 15.0% to 22.5% reduction in fuel burn compared to a Boeing 737-800 aircraft.</p> <p>Another challenge with modeling hybrid-electric aircraft is determining their off-design performance characteristics (considering a different payload or mission range, or both). This work presents an energy management tool – set up as a nonlinear programming optimization problem – to minimize the fuel burn for a payload-range combination by identifying the optimal combination of throttle settings for the gas turbine engines and the electric motors during takeoff, climb, and cruise, along with identifying an optimal flight path. The energy management tool enables fuel savings of at least of 2%, with actual savings ranging from 142.1 lbs to 276.1 lbs per trip for a sample route (LGA–ORD) at a 80% load factor.</p> <p>Although the hybrid-electric aircraft sizing and performance analysis studies show encouraging results about the potential reduction in carbon emissions at an aircraft level, the future fleet-level carbon emissions are not expected to reduce proportionally to these aircraft level emission reductions. This work predicts the fleet-level environmental impacts of future single-aisle parallel hybrid-electric aircraft by modeling the behavior of a profit-seeking airline (with a mixture of conventional all Jet-A fuel burning and hybrid electric aircraft in its fleet) using the Fleet-Level Environmental Evaluation Tool (FLEET). FLEET’s model-based predictions rely upon historically-based information about US-touching airline routes and passenger demand served by US flag-carrier airlines from the Bureau of Transportation Statistics to initiate model-based predictions of future demand, aircraft fleet mix, and aircraft operations. Using the aircraft performance coefficients from the energy management tool to represent the behavior of a single-aisle parallel hybrid-electric aircraft, the FLEET simulation predicts the changes in the fleet-wide carbon emissions due to the introduction of this new aircraft in an airline fleet in the year 2035. By 2055, FLEET results predict that the fleet-wide CO2 emissions with hybrid-electric aircraft in the fleet mix are at least 1.2% lower than the fleet-wide CO2 emissions of a conventional (all Jet-A fuel burning) aircraft-only airline. The rather limited reduction in emissions is an attribute of the reduced range capability and higher operating cost of the hybrid-electric aircraft (relative to a conventional aircraft of similar size). This causes the airline to change the usage, acquisition and retirement of its conventional aircraft when hybrid-electric aircraft are available; this is most notable to serve passenger demand on certain predominantly single-aisle service routes that cannot be flown by the future single-aisle hybrid-electric aircraft. </p>

<p dir="ltr">This thesis details the development of a multidisciplinary design analysis (MDA) framework intended to evaluate a rocket-powered, reusable hypersonic vehicle. In particular, the analysis framework computes the design closure of a coupled system resembling Stratolaunch Systems’ Talon-A reusable hypersonic test vehicle. The resulting analysis framework differs from available literature due to its focus upon payload-related design considerations. The presented framework, too, avoids the use of proprietary technical information and/or export-controlled analysis tools. The framework’s geometric analysis, for example, employs a reverse-engineered geometry resembling Talon-A. An open-source aerothermal package, too, was selected to evaluate the vehicle’s aerothermodynamic characteristics. Quick-to-implement methods were prioritized to expedite the development of the MDA framework. Notably, a regression-based structural analysis model was used, as well as an interpolative thermal protection system (TPS) sizing procedure. A quasi-steady trajectory model, too, was implemented within the MDA framework, to determine the vehicle’s mission performance. The resulting analysis takes the form of a six-discipline MDA framework that can calculate, among other parameters, the vehicle’s cruise duration. Initial design closure results for a vehicle resembling Talon-A, using an assumed TPS size, are currently available. These results report an estimated total vehicle mass within thirty percent of Talon-A’s true gross mass, as well as a cruise duration of approximately 445 seconds. These design closure results were also evaluated under a perturbed specific impulse of ±10%, with a resulting change in cruise duration of ±12.3%. Results for a cruise-condition design exploration procedure were also obtained within a simplified, sequential analysis chain. These design exploration results report a maximum cruise lift-to-drag ratio of approximately four. Future work has been identified, too, including the integration of more rigorous analysis tools for use within future iterations of the MDA framework. Notably, these tools include an open-source optimal control library, as well as a physics-based TPS sizing tool</p>

Multidisciplinary design optimization (MDO) requires many designs to be evaluated while searching for an optimum. As a result, the calculations done to evaluate the designs must be quick and simple to have a reasonable turn-around time. This makes aerodynamic calculations in the transonic regime difficult. Running computational fluid dynamics (CFD) calculations within the MDO code would be too computationally expensive. Instead, CFD is used outside the MDO to find two-dimensional aerodynamic properties of a chosen airfoil shape, BACJ, at a number of points over a range of thickness-to-chord ratios, free-stream Mach numbers, and lift coefficients. These points are used to generate surrogate models which can be used for the two-dimensional aerodynamic calculations required by the MDO computational design environment. Strip theory is used to relate these two-dimensional results to the three-dimensional wing. Models are developed for the center of pressure location, the lift curve slope, the wave drag, and the maximum allowable lift coefficient before buffet. These models have good agreement with the original CFD results for the airfoil. The models are integrated into the aerodynamic and aeroelastic sections of the MDO code. / Master of Science

In this work, the data analysis of oscillating flapping fins is conducted for mathematical model. Data points of heave and surge force obtained by the CFD (Computational Fluid Dynamics) for different geometrical kinds of flapping fins. The fin undergoes a combination of vertical and angular oscillatory motion, while travelling at constant forward speed. The surge thrust and heave lift are generated by the combined motion of the flapping fins, especially due to the carrier vehicle’s heave and pitch motion will be investigated to acquire system identification with CFD data available while the fin pitching motion is selected as a function of fin vertical motion and it is imposed by an external mechanism. The data series applied to model unsteady lifting flow around the system will be employed to develop an optimization algorithm to establish an approximation transfer function model for heave force and obtain a predicting black box system with nonlinear theory for surge force with fin motion control synthesis.

A Otimização Multidisciplinar em Projeto (em inglês, Multidisciplinary Design Optimization - MDO) é uma ferramenta de projeto importante e versátil e seu uso está se expandindo em diversos campos da engenharia. O foco desta metodologia é unir disciplinas envolvidas no projeto para que trabalhem suas variáveis concomitantemente em um ambiente de otimização, para obter soluções melhores. É possível utilizar MDO em qualquer fase do projeto, seja a fase conceitual, preliminar ou detalhada, desde que os modelos numéricos sejam ajustados às necessidades de cada uma delas. Este trabalho descreve o desenvolvimento de um código de MDO para o projeto conceitual de asas flexíveis de aeronaves, com restrição quanto ao fenômeno denominado flutter. Como uma ferramenta para o projetista na fase conceitual, os modelos numéricos devem ser razoavelmente precisos e rápidos. O intuito deste estudo é analisar o uso de metamodelos para a previsão do flutter de asas de aeronaves no código de MDO, ao invés de um modelo convencional, o que pode alterar significativamente o custo computacional da otimização. Para este fim são avaliados três técnicas diferentes de metamodelagem, que foram escolhidas por representarem duas classes básicas de metamodelos, a classe de métodos de interpolação e a de métodos de aproximação. Para representá-las foram escolhidos o método de interpolação por funções de base radial e o método de redes neurais artificiais, respectivamente. O terceiro método, que é considerado um método híbrido dos dois anteriores, é chamado de redes neurais por funções de bases radiais e é uma tentativa de acoplar as características de ambos em um único metamodelo. Os metamodelos são preparados utilizando um código para solução aeroelástica baseado no método dos elementos finitos acoplado com um modelo aerodinâmico linear de faixas. São apresentados resultados de desempenho dos três metamodelos, de onde se pode notar que a rede neural artificial é a mais adequada para previsão de flutter. O processo de MDO é realizado com o uso de um algoritmo genético multi-objetivo baseado em não-dominância, cujos objetivos são a maximização da velocidade crítica de flutter e a minimização da massa estrutural. Dois estudos de caso são apresentados para avaliar o desempenho do código de MDO, revelando que o processo global de otimização realiza de fato a busca pela fronteira de Pareto. / The Multidisciplinary Design Optimization, MDO, is an important and versatile design tool and its use is spreading out in several fields of engineering. The focus of this methodology is to put together disciplines involved with the design to work all their variables concomitantly, at an optimization environment to obtain better solutions. It is possible to use MDO in any stage of the design process, that is in the conceptual, preliminary or detailed design, as long as the numerical models are fitted to the needs of each of these stages. This work describes the development of a MDO code for the conceptual design of flexible aircraft wings, with restrictions regarding the phenomenon called flutter. As a tool for the designer at the conceptual stage, the numerical models must be fairly accurate and fast. The aim of this study is to analyze the use of metamodels for the flutter prediction of aircraft wings in the MDO code, instead of a conventional model itself, what may affect significantly the computational cost of the optimization. For this purpose, three different metamodeling techniques have been evaluated, representing two basic metamodel classes, that are, the interpolation and the approximation class. These classes are represented by the radial basis function interpolation method and the artificial neural networks method, respectively. The third method, which is considered as a hybrid of the other two, is called radial basis function neural networks and is an attempt of coupling the features of both in single code. Metamodels are prepared using an aeroelastic code based on finite element model coupled with linear aerodynamics. Results of the three metamodels performance are presented, from where one can note that the artificial neural network is best suited for flutter prediction. The MDO process is achieved using a non-dominance based multi-objective genetic algorithm, whose objectives are the maximization of critical flutter speed and minimization of structural mass. Two case studies are presented to evaluate the performance of the MDO code, revealing that overall optimization process actually performs the search for the Pareto frontier.

Este trabalho consiste no desenvolvimento de uma metodologia de otimização multidisciplinar de projeto conceitual de aeronaves. O conceito de aeronave otimizada tem como base o estudo evolutivo de características das categorias imediatas àquela que se propõe. Como estudo de caso, foi otimizada uma aeronave de treinamento militar que faça a correta transição entre as fases de treinamento básico e avançado. Para o estabelecimento dos parâmetros conceituais esse trabalho integra técnicas de entropia estatística, desdobramento da função de qualidade (QFD), aritmética fuzzy e algoritmo genético (GA) à aplicação de otimização multidisciplinar ponderada de projeto (OMPP) como metodologia de projeto conceitual de aeronaves. Essa metodologia reduz o tempo e o custo de projeto quando comparada com as técnicas tradicionais existentes. / This work is concerned with the development of a methodology for multidisciplinary optimization of the aircraft conceptual design. The aircraft conceptual design optimization was based on the evolutionary simulation of the aircraft characteristics outlined by a QFD/Fuzzy arithmetic approach where the candidates in the Pareto front are selected within categories close to the target proposed. As a test case a military trainer aircraft was designed target to perform the proper transition from basic to advanced training. The methodology for conceptual aircraft design optimization implemented in this work consisted on the integration of techniques such statistical entropy, quality function deployment (QFD), arithmetic fuzzy and genetic algorithm (GA) to the weighted multidisciplinary design optimization (WMDO). This methodology proved to be objective and well balanced when compared with traditional design techniques.

The research objective of this dissertation is to create and demonstrate methods for parameterizing the Pareto frontiers of continuous multi-attribute design problems using barycentric coordinates, and in doing so, to enable intuitive exploration of optimal trade spaces. This work is enabled by two observations about Pareto frontiers that have not been previously addressed in the engineering design literature. First, the observation that the mapping between non-dominated designs and Pareto efficient response vectors is a bijection almost everywhere suggests that points on the Pareto frontier can be inverted to find their corresponding design variable vectors. Second, the observation that certain common classes of Pareto frontiers are topologically equivalent to simplices suggests that a barycentric coordinate system will be more useful for parameterizing the frontier than the Cartesian coordinate systems typically used to parameterize the design and objective spaces. By defining such a coordinate system, the design problem may be reformulated from y = f(x) to (y,x) = g(p) where x is a vector of design variables, y is a vector of attributes and p is a vector of barycentric coordinates. Exploration of the design problem using p as the independent variables has the following desirable properties: 1) Every vector p corresponds to a particular Pareto efficient design, and every Pareto efficient design corresponds to a particular vector p. 2) The number of p-coordinates is equal to the number of attributes regardless of the number of design variables. 3) Each attribute y_i has a corresponding coordinate p_i such that increasing the value of p_i corresponds to a motion along the Pareto frontier that improves y_i monotonically. The primary contribution of this work is the development of three methods for forming a barycentric coordinate system on the Pareto frontier, two of which are entirely original. The first method, named "non-domination level coordinates," constructs a coordinate system based on the (k-1)-attribute non-domination levels of a discretely sampled Pareto frontier. The second method is based on a modification to an existing "normal boundary intersection" multi-objective optimizer that adaptively redistributes its search basepoints in order to sample from the entire frontier uniformly. The weights associated with each basepoint can then serve as a coordinate system on the frontier. The third method, named "Pareto simplex self-organizing maps" uses a modified a self-organizing map training algorithm with a barycentric-grid node topology to iteratively conform a coordinate grid to the sampled Pareto frontier.

A framework is proposed that combines separately developed multidisciplinary optimization, multi-objective optimization, and joint probability assessment methods together but in a decoupled way, to solve joint probabilistic constraint, multi-objective, multidisciplinary optimization problems that are representative of realistic conceptual design problems of design alternative generation and selection. The intent here is to find the Weak Pareto Frontier (WPF) solutions that include additional compromised solutions besides the ones identified by a conventional Pareto frontier. This framework starts with constructing fast and accurate surrogate models of different disciplinary analyses. A new hybrid method is formed that consists of the second order Response Surface Methodology (RSM) and the Support Vector Regression (SVR) method. The three parameters needed by SVR to be pre-specified are automatically selected using a modified information criterion based on model fitting error, predicting error, and model complexity information. The model predicting error is estimated inexpensively with a new method called Random Cross Validation. This modified information criterion is also used to select the best surrogate model for a given problem out of the RSM, SVR, and the hybrid methods. A new neighborhood search method based on Monte Carlo simulation is proposed to find valid designs that satisfy the deterministic constraints and are consistent for the coupling variables featured in a multidisciplinary design problem, and at the same time decouple the three loops required by the multidisciplinary, multi-objective, and probabilistic features. Two schemes have been developed. One scheme finds the WPF by finding a large enough number of valid design solutions such that some WPF solutions are included in those valid solutions. Another scheme finds the WPF by directly finding the WPF of each consistent design zone. Then the probabilities of the PCs are estimated, and the WPF and corresponding design solutions are found. Various examples demonstrate the feasibility of this framework.

Research into advanced wind turbine design has shown that load alleviation strategies like bend-twist coupled blades and coned rotors could reduce costs. However these strategies are based on nonlinear aero-structural dynamics providing additional benefits to components beyond the blades. These innovations will require Multi-disciplinary Design Optimization (MDO) to realize the full benefits. This research expands the MDO capabilities of Horizontal Axis Wind Turbines. The early research explored the numerical stability properties of Blade Element Momentum (BEM) models. Then developed a provincial scale wind farm siting models to help engineers determine the optimal design parameters. The main focus of this research was to incorporate advanced analysis tools into an aero-elastic optimization framework. To adequately explore advanced designs with optimization, a new set of medium fidelity analysis tools is required. These tools need to resolve more of the physics than conventional tools like (BEM) models and linear beams, while being faster than high fidelity techniques like grid based computational fluid dynamics and shell and brick based finite element models. Nonlinear beam models based on Geometrically Exact Beam Theory (GEBT) and Variational Asymptotic Beam Section Analysis (VABS) can resolve the effects of flexible structures with anisotropic material properties. Lagrangian Vortex Dynamics (LVD) can resolve the aerodynamic effects of novel blade curvature. Initially this research focused on the structural optimization capabilities. First, it developed adjoint-based gradients for the coupled GEBT and VABS analysis. Second, it developed a composite lay-up parameterization scheme based on manufacturing processes. The most significant challenge was obtaining aero-elastic optimization solutions in the presence of erroneous gradients. The errors are due to poor convergence properties of conventional LVD. This thesis presents a new LVD formulation based on the Finite Element Method (FEM) that defines an objective convergence metric and analytic gradients. By adopting the same formulation used in structural models, this aerodynamic model can be solved simultaneously in aero-structural simulations. The FEM-based LVD model is affected by singularities, but there are strategies to overcome these problems. This research successfully demonstrates the FEM-based LVD model in aero-elastic design optimization. / Graduate / 0548 / pilot.mm@gmail.com

La conception d'un système électrique est une tâche très complexe qui relève d’expertises dans différents domaines de compétence. Dans un contexte compétitif où l’avance technologique est un facteur déterminant, l’industrie cherche à réduire les temps d'étude et à fiabiliser les solutions trouvées par une approche méthodologique rigoureuse fournissant une solution optimale systémique.Il est alors nécessaire de construire des modèles et de mettre au point des méthodes d'optimisation compatibles avec ces préoccupations. En effet, l’optimisation unitaire de sous-systèmes sans prendre en compte les interactions ne permet pas d'obtenir un système optimal. Plus le système est complexe plus le travail est difficile et le temps de développement est important car il est difficile pour le concepteur d'appréhender le système dans toute sa globalité. Il est donc nécessaire d'intégrer la conception des composants dans une démarche systémique et globale qui prenne en compte à la fois les spécificités d’un composant et ses relations avec le système qui l’emploie.Analytical Target Cascading est une méthode d'optimisation multi niveaux de systèmes complexes. Cette approche hiérarchique consiste à décomposer un système complexe en sous-systèmes, jusqu’au niveau composant dont la conception relève d’algorithmes d'optimisation classiques. La solution optimale est alors trouvée par une technique de coordination qui assure la cohérence de tous les sous-systèmes. Une première partie est consacrée à l'optimisation de composants électriques. L'optimisation multi niveaux de systèmes complexes est étudiée dans la deuxième partie où une chaîne de traction électrique est choisie comme exemple / The design of an electrical system is a very complex task which needs experts from various fields of competence. In a competitive environment, where technological advance is a key factor, industry seeks to reduce study time and to make solutions reliable by way of a rigorous methodology providing a systemic solution.Then, it is necessary to build models and to develop optimization methods which are suitable with these concerns. Indeed, the optimization of sub-systems without taking into account the interaction does not allow to achieve an optimal system. More complex the system is more the work is difficult and the development time is important because it is difficult for the designer to understand and deal with the system in its complexity. Therefore, it is necessary to integrate the design components in a systemic and holistic approach to take into account, in the same time, the characteristics of a component and its relationship with the system it belongs to.Analytical Target Cascading is a multi-level optimization method for handling complex systems. This hierarchical approach consists on the breaking-down of a complex system into sub-systems, and component where their optimal design is ensured by way of classical optimization algorithms. The optimal solution of the system must be composed of the component's solutions. Then a coordination strategy is needed to ensure consistency of all sub-systems. First, the studied and proposed optimization algorithms are tested and compared on the optimization of electrical components. The second part focuses on the multi-level optimization of complex systems. The optimization of railway traction system is taken as a test case