The addition of lead to the copper alloys increases its machinability and reducesthe overall production cost, despite copper being expensive, which makes achallenging task to replace lead. But the alarming effects of lead on human healthand the recycling problems has led to the increase in concern forreducing/eliminating the use of lead in brass and other copper alloys. Manymaterials are considered to replace lead in brass; silicon is one such alternative.The turned brass sample are investigated using the state of the artequipments at Halmstad University. The results obtained are controlled readingsof surface parameters and is categorized using surface imaging and mappingsoftware, Mountains Map.This thesis characterizes the lead and the lead free brass's surfaceintegrity for a certain cutting data. The study deals with the evaluation ofselection of appropriate surface integrity parameters and summarizes theappropriate combination of cutting data to maintain the surface of the ecobrass/unleaded brass on par with the leaded brass surface. The 2D and 3Dsurface parameters illustrates the surface functionality and its effect on thematerial in contact.The research results suggest a detailed methodology for the analysis ofsurface topography and a comparison exemplifying differences between the twomaterials under study. The research provides a perplexed results and forms thebasis for further investigations of the samples machined at different cutting data.Second set of test includes comparing the Leaded brass with the unleaded brasssamples machined at 0.06, 0.1, 0.15 and 0.2mm/rev respectively. The studyfocuses on the correlation of cutting feed and the surface parameters. Comparingthe results of two tests, the unleaded brass machined @ feed rate 0.2mm/rev,200m/min, 1.5mm depth of cut posses similar surface functionality as leadedbrass.

The ease of manufacturing complex geometries using fused deposition modeling (FDM) 3D-Printing reduces the overall production cost compared with the traditional manufacturing techniques. Because of the benefits of 3D printing technologies, it is proposed to be used in the manufacturing of different products. But there is still no definite characterization of the surface quality of objects manufactured by 3D printing. Hence in order to define the texture of the surfaces produced, measurements from different samples are taken and quantified.In this study, a 3D test model consisting of various slopes is printed at different layer thicknesses and different print speeds using different 3D printers.Thus, the effect of the surface orientation on the surface roughness was studied in relation to the different layer thicknesses and different print speeds. The study samples are measured using the state of the art equipment at Halmstad University.This thesis studies the surface roughness at different slopes of FDM models.A related study on the dimensional variation between the CAD model and the actual3D printed model, and causes/reasons for the variations are analyzed.It is observed that FDM produced part surface topography is directly affected by the orientation of the surface. Also, the surface roughness increases with increase in layer thickness. The observed correlations between surface roughness and layer thickness and surface orientation could be used to better understand the behavior of FDM surfaces, thus to better quantify the surface roughness. To improve quality, it must first be quantified. It is well observed that dimensional inaccuracy exists between the CAD model and the printed part. These results suggest that there is a lot of work and improvements to be done in order to close the gap of dimensional inaccuracy and achieve a high precision commercial FDM 3Dprinting.

Increasing environmental awareness has driven a lot of research to look into various environmentally friendly lubricants which can replace more conventional mineral oil based lubricants. This is true in particular for marine and hydropower applications where the risk of lubricant leakage can be damaging to the local environment. Glycerol is an organic compound produced as a byproduct when producing Biodiesel. It is environmentally friendly and has been used by the pharmaceutical and food industries for a long time. Recent research has shown that glycerol has very good tribological properties and can be used as a lubricant in some applications. However, its high viscosity and high static friction are disadvantageous and needs improvement. The purpose of this study is to investigate possible surface active environmentally adapted additives in glycerol and water solutions. 14 additives have been selected for testing and were tested in a pin-on-disc start-stop friction test to see their effect on the static and dynamic friction coefficients. From these 14 additives two were selected due to their superior performance and were further studied. The effect of concentration of water and additive in glycerol was also investigated using the same test conditions. A phosphor based additive has been found to be the best performing.

Improving vehicle efficiency and complying to stricter exhaust emission legislations are some of the driving factors to advancement in technology of engine components. The main bearings in an internal combustion engine contribute significant amount of friction. These bearings support engine loads and allow free rotation of the crankshaft. The bearings consist of a steel backing, a lining material and an optional overlay. The overlays help to minimize friction and enhance seizure resistance during adverse operating conditions. The aim of the thesis is to study the friction and wear performance of five multi-layered bearings with various overlays. A bi-metal bearing is used as the reference for comparison. Additionally, influence of two shaft surface textures are also studied comparing to the standard shaft surface finish. A modified twin-disc test rig is used to evaluate tribological performance of the bearing system. Forced misalignment tests were also performed to simulate edge contact conditions, which occur in an engine due to shaft deflection, asymmetrical loading and other factors. The bearing surface profiles were measured using an optical interferometer. The test setup showed good repeatability and consistent results. Relative friction and wear performance are compared and the bearings are ranked accordingly. One bearing type with a polymer and MoS2 overlay showed the best overall performance. This bearing combined with a plateau textured shaft further lowered the friction coefficient by 3 % in boundary and mixed lubrication regime.

På Volvo Group Trucks Operations (GTO) i Skövde tillverkas cylinderblock, cylinderhuvud och svänghjul genom gjutning med sandformar. Då formverktygen som formar sandformarna fylls uppkommer slitage där sandpartiklarna träffar, vilket leder till att formverktygen behöver underhållas regelbundet.Målet med denna studie är att hitta alternativa material som formverktygen kan tillverkas i alternativt förstärkas eller beläggas med för att minska slitaget i formverktygen och på så sätt minska kostnader genom att förlänga underhållsintervallen. Problemet analyseras och en litteraturstudie kring erosiv och abrasiv nötning genomförs.Ett antal material tas fram genom en materialvalsprocess som lämpliga kandidater baserat på litteraturstudien, materialkartor och diskussion. Materialprover testas med en standardmetod för erosion med gasburna partiklar. Resultat från tidigare empiriska studier tyder på att erosion påverkas starkt av materialegenskaper så som hårdhet och seghet men även de eroderande partiklarnas infallsvinkel och hastighet.Erosionstestet utförs för 30 och 90 graders infallsvinkel. Testet visar att de mjukare stålen, Holdax och Sverker 21, har högre beständighet mot erosion vid låga infallsvinklar och det hårdare stålet Nimax har högre beständighet vid höga infallsvinklar. Nimax anses vara ett lämpligt material till formverktyget då Nimax har den totalt lägsta erosionstakten vid hopslagning av den totala erosionstakten över båda infallsvinklarna. Nimax har den lägsta erosionstakten vid 30 graders infallsvinkel och anses även ha god beständighet mot erosion vid 90 graders infallsvinkel.Rekommendation ges kring upprepade erosionstester för att säkerställa resultatet. Rekommendationer finns också kring materialprovning i formverktyget för att se om ett materialbyte skulle leda till besparingar. Undersökning av möjligheter att konstruera bort nötning i formverktyget genom ändring av infallsvinklar mellan den inblåsta sanden och formverktyget, samt ändring av lufttryck rekommenderas. / At Volvo Group Trucks Operations (GTO) in Skövde, cylinder blocks, cylinder heads and flywheels are manufactured through sandcasting. As the forming tools that forms the sand forms are filled with sand, wear occurs where the sand particles hit the tool surface. The forming tool thus needs to be regularly maintained. The aim of this study is to evaluate alternative materials that the forming tools can be manufactured in to reduce wear, and thereby reducing costs by extending maintenance intervals. The problem is analyzed and a literature study on erosive and abrasive wear is carried out. A number of materials are presented as suitable candidates based on the literature study, material charts and discussion. Material samples are tested using a standard method for solid particle erosion using gas jets. Results from previous empirical studies indicate that erosion is strongly influenced by material properties such as hardness and toughness but also the angle of impingement and velocity of the erosive particles.The erosion test is performed at 30 and 90 degree angle of impingement. The test shows that the softer steel, Holdax and Sverker 21 have higher resistance to erosion at low angles of impingement and the harder steel Nimax has higher resistance at high angles of impingement. Nimax is considered a suitable material for the forming tool, as Nimax has the overall lowest erosion rate when adding the total erosion over both angles of impingement. Nimax has the lowest erosion rate at 30 degrees angle and is also considered to have good resistance to erosion at 90 degrees angle. Recommendation is given on repeated erosion tests to validate the results. There are also recommendations regarding material testing in the forming tool to see if a material change would lead to savings. Examination of possibilities to make changes in the sand filling process, altering angle of impingement between the sand blown and the forming tool as well as air pressure is recommended.

Thermal fatigue is a serious problem in todays power plants. A large amount of damages around the world circles around that subject. The damage can come from the mechanism of two flows mixing with different temperatures in a T-junction. It is a fundamental prerequisite that these T-junctions are frequently tested for damages. An amount of criterias steers the rate of testings. This guide/document will provide the process of rating the T-junctions resistance with valid information and ease the course. If a T-junction is stated as very sensetive for thermal fatigue, it will be graded with a low damage index. This value is reliant of the temperature difference between the two flows and can be changed with different actions, for example by adding a mixer to the T-junction. The mixer will blend the two flows so the thermal fatigue reduces or doesn’t occour at all. The T-junction can be tested with several methods, ultra sonic testing or eddy-current testing. The ultra sonic testing method is the most used method and can test the inside of the T-junction pipe without access of the inside.

Syftet med detta projektarbete var att minska energiförlusterna i Getrag All Wheel Drives hypoidväxlar (se kapitel 7.2.3). Uppdraget bestod främst av att minska förlusterna när systemet endast driver på två hjul och de övriga hjulparen endast överför låga kraftmoment, detta förhållande benämns draggmoment. För att kunna utvärdera och peka på förbättringsområden var första steget i arbetet att lokalisera och värdera enskilda komponenter som tillförde förluster. De ingående komponenter som studerades grundligt var lager, Kuggkontakt, olja och tätningar. Värderingen av komponenternas respektive förlustbidrag erhölls genom provning och beräkningar. Provningen bestod dels av tidigare utförd provning och dels av provning utförd under arbetets gång. För beräkning av lager och tätningar användes beräkningen från lagertillverkaren SKFs egna beräkningsmodeller. Beräkning av hypoidväxelns smörjningsförluster skedde enligt ISO/TR 14179-2. Övriga beräkningar härleddes genom tribologiska formler med givna friktionskoefficienter. När ingående komponenter var värderade genom beräkningar och provning valdes de komponenter som tillförde de största förlusterna att utvecklas vidare. Vald komponent att förbättra blev lager, där förspänningen av lageranordningen mellan kronhjulsaxeln och aluminiumhus studerades. Utöver lagerförspänningen undersöktes även inverkan av oljans viskositet på lager och växel som helhet. Resultatet från konceptgenereringen resulterade i en lösning där en aluminiumring ska monteras mellan två koniska rullager på röraxeln för att bibehålla den initiala förspänningen mellan dessa lager under förhöjda temperaturer. Detta bidrar till att kunna sänka den initiala förspänningen. Genom användning av en förspänningsring av aluminium kan initial förspänning enligt analys och beräkningar sänkas från 13 kN till cirka 6 kN. Enligt beräkningar minskar momentförlusterna i lager på röraxeln då med 0,36 Nm. Det Andra konceptet var att välja en olja med lägre viskositet än dagens produktionsolja och på så vis erhålla en minskning av momentförluster. Från en kinematisk viskositet på cirka 45 mm2/s till en kinematisk viskositet på 33 mm2/s vid 80 °C minskades RDU-växelns(bakre hypoidväxel) totala förluster i lager med 0,53 Nm. Rekommendationen för fortsatt arbete blev att börja utföra grundliga tester för en olja med lägre viskositet och sedan om godkända resultat erhålls byta ut dagens växelolja. Samt att i ett senare skede genomföra provning med en förspänningsring om ytterligare förbättrad verkningsgrad önskas.

Lubrication is critical in order to achieve high efficiency and reliability of machine elements such as gears, bearings, and other moving mechanical assemblies (MMA). In space applications, tribological properties of lubricants are quickly growing more important. Traditional space systems such as satellites imply MMA such as gyroscopes, antenna pointing mechanisms, and solar array drives. These MMA operate in high vacuum (<10-5 Pa) under lightly loaded conditions. Modern space missions on the other hand, such as remotely operated vehicles used for in-situ Mars exploration relies on different types of MMA. In these robotic systems, electromechanical actuators are being used extensively to provide controlled motion. Gears and bearings in these actuators operate in an atmosphere mainly consisting of CO2 at ~10+3 Pa under heavily loaded contact conditions. In these conditions, the tribosystem is likely to operate in the boundary lubricated regime, with consequent risk of high friction and wear. High molecular weight fluids have significant heritage in space because of their low vapor pressure. They are currently employed as lubricants in a wide range of space applications, as they meet high demands on resistance to vacuum outgassing. Unfortunately, the large molecules are susceptible to degradation under heavy load. Ionic liquids (ILs) on the other hand, are synthetic fluids that consist entirely of ion pairs with opposing charge. The resulting ion bonds enable inherently low vapor pressure of the fluid without the need for a high molecular weight. For this reason ILs have been advocated as potential lubricants for space applications, but so far compatibility issues have hampered their use as lubricants. Countless IL variations are possible, and solutions are thus likely to exist. Constituent ions can be designed individually and combined in various configurations. However, the fundamental understanding of the lubricating mechanism of ionic liquids is still incomplete, and consequently the optimum molecular structure for IL lubricants remain unknown. In this thesis, a stepwise approach to molecular design of IL lubricants is described, and the resulting hydrocarbon-mimicking ionic liquids are evaluated in tribological experiments. In this thesis, the experiments focus on tribological performance, using steel-steel tribopairs in air environment under boundary lubrication (Paper I). Boundary film formation under a range of contact pressures and temperatures, is analyzed after tribotesting by optical profilometry, scanning electron microscopy (SEM), and energy dispersive X- iii ray spectroscopy (EDS) in Paper II. The analysis reveal formation of a highly effective boundary film based on silicate, that can be further enhanced by amine additives. This thesis demonstrates the feasibility of improving tribological performance of ionic liquids by molecular design. / Projekt: Rymdforskarskolan 2015

The constant pursuit in the automotive industry to increase the engines performance, new solutions are always developed and tested to reduce the friction and increase the efficiency in the engine. One component that contributes to friction losses is the piston ring pack where the top compression stands for up to 40 %. This master thesis collaborated with Scania’s material science department Basic engine and covers the friction and wear of four different materials on the cylinder liner surface against the top compression ring.The four tested materials were grey cast iron with different honing quality and three atmospheric plasma sprayed coatings with titanium oxide, chromium oxide and Metco’s mixture F2071 which is a stainless steel mixed with a ceramic. A martensitic steel piston ring with a chromium coated sliding surface was used for all the testing in the Cameron-Plint TE77 test-rig. This is a pin-on-disc test method and the parameters used for testing is set to replicate the environment the ring is exposed to at the top dead centre.The test-rig has been in Scania’s possession for a long time and has not always given a satisfying result. An uneven contact between the ring and liner has been a problem resulting in only worn edges of the liner specimen. The piston ring holder was therefore redesigned to be able to adjust the radius of the ring. This allowed a good conformability between the ring and liner to be obtained.The tested materials were evaluated according to friction and wear. Friction was measured with the test-rig and the wear was calculated with surface profiles that were measured before and after testing. Worn surfaces were studied in a SEM to verify which wear mechanism that was active. The changes of the surfaces was studied with the use of following surface parameters Ra, Rk, Rpk, Rvk and if there was a connection between these parameters and friction and wear coefficient.Independent of honing quality showed the grey cast iron lowest friction coefficient just under 0.13, the F2071 liner showed a friction coefficient just above 0.13. Both oxide layers showed similar friction where the chromium oxide had a friction just below 0.15 and the titanium oxide lay just above 0.15. Lowest wear coefficient had the chromium oxide followed by F2071, titanium oxide and the bad honed grey cast iron. These three liners showed almost the exact same wear coefficient. Worst wear coefficient had the grey cast iron with a good honing quality. A mild abrasive wear mechanism was active during the wear test and vague wear marks was found on the surface. There is no connection between wear coefficient and friction and the change in surface roughness during the test does not affect the friction.

The present work deals with developing a tribological test machine that had been built earlier but did not function properly. It was giving out abnormal noises and vibrations and was not corresponding to its desired functions. In this study, the root of these problems is analyzed and some solutions are suggested by developing a new construction concept for the machine.