Iron platinum (FePt) has attracted growing interest because of its high Curie temperature, magneto-crystalline anisotropy and chemical stability. Nanoparticles (NPs) made of this alloy are promising candidates for a wide range of biomedical applications including magnetic separation, magnetic targeted drug delivery, hyperthermia for cancer therapy and also as magnetic resonance imaging (MRI) contrast agents. This thesis presents the synthesis, functionalization and characterization of FePt NPs along with a toxicity study and an investigation into their application as MRI contrast agents. Regarding their synthesis, different approaches have been explored including the co-reduction of Fe and Pt precursors in an aqueous media, the thermal decomposition in a conventional high-boiling solvent such as benzyl ether, and in low-melting organic salts (ionic liquids). The data revealed an inhomogeneous composition distribution of Fe and Pt between particles obtained in aqueous media, due to the iron salts hydrolysis, and a mismatch in the co-reduction kinetic of the two metal precursors. While the iron content in the NPs could be increased by using more hydrolytically stable iron precursors or stronger reducing agents, there are remaining limiting parameters which prevent further Fe content increase in NPs. In contrast, by excluding the water from the reaction system and using a Fe²⁻ iron precursor, homogenous 1:1 Fe to Pt ratio NPs can be obtained through a modified thermal decomposition pathway in benzyl ether. Based on the study of synthesis in this conventional chemical, the potential of ionic liquids (ILs) to be used as novel solvents for FePt NPs synthesis was further explored. It was then demonstrated that ionic liquids (ILs) can not only be used as a solvent for synthesis of FePt NPs, but also can provide an exciting alternative pathway to direct synthesis fct-FePt NPs. In the context of the bioapplication of FePt NPs, a family of FePt NPs was specifically designed to enhance their MRI contrast agents properties. In contrast with previous reports, this thesis demonstrates that FePt NPs can be made non-toxic and provides the first data on their cellular uptake mechanisms. A six times increase in the FePt based T₂ contrast properties compared to clinical iron oxide NPs is reported. The relationship between the MRI contrast properties and the NPs architecture is explored and rationalised as the basis for the design of NPs as enhanced MRI contrast agents. Finally, the first observations of cellular and in vivo MR imaging with FePt NPs is also reported. This study opens the way for several applications of FePt NPs such as regenerative medicine and stem cell therapy, thus providing a bio-platform to develop novel diagnostic and therapeutic agents.

Dans les cellules photovoltaïques organiques, le matériau utilisé pour le transport de trous entre la couche active et l'électrode, est généralement un polymère dopé, dont la stabilité peut être problématique. L'objectif de cette thèse a été de développer des matériaux inorganiques, a priori plus stables, pour remplacer les couches de polymères de transport de trous, tout en restant compatible avec les méthodes de dépôts par voie liquide. L'utilisation de nanoparticules dispersées en solution a été choisie car cela permet le dépôt à basse température, sans nécessité de conversion vers une couche fonctionnelle, contrairement aux voies sol-gel. Le premier objectif de ce travail a donc été l'obtention de nanoparticules d'oxyde de tungstène, hydraté ou non, et de thiocyanate de cuivre. Une synthèse de chauffage assisté par micro-ondes a été utilisée pour l'oxyde de tungstène, permettant d'obtenir des nanoparticules de 30 nm et monodisperses. Pour le thiocyanate de cuivre, il a été choisi de travailler par broyage. Les paramètres du broyage ont été optimisés pour obtenir des particules avec la plus faible distribution en taille possible. Le dépôt de ces dispersions de nanoparticules a permis l'obtention de couches minces et la caractérisation de leurs propriétés optoélectroniques, et notamment du travail de sortie, qui s'est révélé adapté pour une utilisation en dispositif. Des cellules solaires organiques de structures standard et inverse incorporant ces matériaux ont ensuite été réalisées. De bonnes performances ont été obtenues avec une couche active à base de P3HT, notamment en structure inverse où la possibilité d'utiliser le thiocyanate de cuivre a été démontrée pour la première fois. Le suivi des performances sous éclairement et atmosphère contrôlée a également été effectué et a montré un vieillissement rapide pour ces cellules comparées aux cellules de référence à couche de transport de trous polymère. / In organic solar cells, a doped polymer is the most used material for hole transport between the active layer and the electrode, but his stability can be an important issue. The goal of this PhD thesis was to develop inorganic materials, expected to be more stable, in order to replace polymer based hole transporting layers. Another requirement was to keep the compatibility with solution-based deposition methods. The target was to develop nanoparticle dispersions, deposited at low temperature and giving directly a functional layer, without the need of further treatments which are usually required via sol-gel processes. A first objective of the present work was thus the elaboration of nanoparticles of tungsten oxide, hydrated or non-hydrated, and copper thiocyanate. A microwave-assisted heating synthesis has been used for tungsten oxide, leading to mono-dispersed particles around 30 nm. Concerning copper thiocyanate, a ball milling technique has been chosen. The process parameters have been optimized to obtain nanoparticles to narrow the size distribution as much as possible. The deposition of the nanoparticles has allowed the formation of thin layers and the characterization of their optoelectronic properties, such as work function, which was shown to be a relevant parameter for a use in devices. Organic solar cells with standard or inverted structures have been fabricated using these materials as a hole transporting layer. Good photovoltaic performances have been obtained, especially in the inverted structure, in which the possibility to use copper thiocyanate has been demonstrated for the first time. Ageing experiments under light in a controlled atmosphere have also been carried out and have shown a rapid drop in performances for these cells compared to cells incorporating polymer based hole transport layers.

The group of materials with ABO3 type perovskite structure are very important due to their attractive electrical and magnetic properties for technological applications and have been studied in the form of single crystals, bulk polycrystalline materials and thin films. Recently, efforts have been made to synthesize and understand the growth of ABO3 type perovskite nanostructures because of their distinctive physical properties and potential applications in the nanodevices. The primary aim of the present thesis is to synthesize the perovskites at nano-scale, with zero-dimension (0D), and one-dimension (1D) configurations. Basic work was carried in terms of synthesis – structure – composition correlation. Due to the small nature of the synthesized materials, few attempts were done to examine the physical properties, but to a limited extant. Efforts were also done to emphasize the structural behavior of nano perovskite in comparison with their bulk counterparts. Chapter 1 provides a brief introduction to perovskite materials and nanostructures, their technological applications and the fundamental physics involved. A brief review of the perovskite nanostructures both from fundamental science and technological point of view is provided. Finally the specific objectives of the current research are outlined. Chapter 2 deals with the experimental studies carried out in this thesis. It describes the methods used for the synthesis, experimental set up and the basic operation principles of various structural and physical characterizations such as X-ray diffraction (XRD), thermal analysis, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM), compositional analysis (EDX), focused ion beam (FIB), electrical and magnetic studies of the materials prepared. Chapter 3 describes the fabrication of porous anodic aluminum oxide (AAO) templates with different pore size, basic steps for synthesis of nanotubes and the possible growth mechanism of nanotubes in the AAO template. In chapter 4, we report the synthesis of ferroelectric Ba1-xSrxTiO3 (x = 0.0, 0.3) nanoparticles (diameter range: 20-40nm) and Ba1-xSrxTiO3 (x = 0.0, 0.4) nanotubes with diameter about 200nm by the sol-gel method. The Ba1-xSrxTiO3 nanostructures so obtained were characterized by number of techniques, including FE-SEM, XRD, DTA/TGA, FTIR spectroscopy, TEM, HRTEM as well as EDX and SAED. Formation of Y-junctions and multi-branches in Ba1-xSrxTiO3 nanotubes were also observed. The wall of the nanotubes were found to be made of randomly oriented nanoparticles which were confirmed from the HRTEM image. The average thickness of the wall of the nanotubes was found around 15(±5) nm and nanoparticles consisting the wall were found to be in the range of 5-10nm. Diffused phase transition (cubic to tetragonal), shifted to lower temperature side and leaky ferroelectric P–E loops were observed in Ba1-xSrxTiO3 (x = 0.0) ceramic prepared from nanoparticles. Curie temperature was observed at 120oC in the BT nanotube array as confirmed by the dielectric study. The P–E loops of as-prepared Ba1-xSrxTiO3 (x = 0.0) nanotube array were also measured and the hysteresis clearly demonstrates the room temperature ferroelectricity in the as prepared nanotubes, indicating these nanotube array is potential media as ferroelectric information storage. In chapter 5, we report the synthesis of single crystalline nanoparticles and polycrystalline nanotubes of Pb0.76Ca0.24TiO3 (PCT24) by sol-gel processing and characterized by various techniques. The crystallinity and phase purity of the PCT24 nanoparticles and nanotubes were confirmed by the XRD and SAED pattern. Compositional homogeneity and their crystalline structure confirms the formation of the tetragonal perovskite phase. The wall of the nanotubes was found to be made of nanoparticles which were confirmed from the HRTEM analysis. The average thickness of the wall of the nanotubes was found around 20nm and nanoparticles consisting the wall were found to be in the range of 5-8nm. Formation of some single crystalline PCT24 nanorods was also observed as confirmed by SAED and HRTEM analysis. Formations of Y-junctions and multi-branches in this complex functional oxide were observed. Dielectric measurements shows the diffuse phase transition and frequency dependence of Tm (temperature at which real part of dielectric constant shows maxima) suggesting the relaxor type behavior in the PCT24 ceramic prepared from nanoparticles. Polarization study was carried out on PCT24 nanotube array, which shows the ferroelectric nature at room temperature. Chapter 6 reports the synthesis and studies of PbZrO3 (PZ) nanoparticles and PbZr1-xTixO3 for x = 0.0, 0.48 and 1.0 nanotubes. PZ nanoparticles were prepared by a novel sol-gel method based on diol-based solution. Initially, PZ was crystallized with some intermediate m-Z and t-Z phases at 400-550oC and start transforming to orthorhombic at around 600oC and then finally transformed into pure orthorhombic PZ phase at about 700oC. XRD and TEM confirmed the nanocrystalline nature of PZ particles. Curie temperature in the PZ ceramic prepared from PZ nanoparticles was observed around at 205oC, which is lower as compared to the bulk (233oC). P–E hysteresis loops of PZ ceramic prepared from nanoparticles were measured at different applied voltages and single ferroelectric loops of leaky nature were observed rather than antiferroelectrics. The lead zirconate nanoparticles produced may have potential applications as materials used in microelectronics and microelectromechanical systems. PbZr1-xTixO3 for x = 0.0 (PZ), 0.48 (PZT48) and 1 (PT) nanotubes were fabricated by sol-gel method within the closely packed porous alumina templates and characterized by various techniques. The crystallinity of the PZ, PZT48 and PT nanotubes were confirmed via XRD and SAED studies. EDX analysis demonstrated that stoichiometry was formed. Formation of Y-junctions in this complex functional oxide was also observed. The wall of the nanotubes was found to be made up of randomly oriented nanoparticles, which were confirmed by the HRTEM studies and also by a typical SEM image. The average thickness of the wall of the nanotubes was found to be around 10-20nm and nanoparticles consisting the wall was found to be in the range of 3 – 8nm. The Curie temperature was observed at 220oC in the PZ nanotube array. For the first time, PLD has been employed for the synthesis of lead zirconate nanotubes using AAO template. Well-registered arrays of these nanotubes could function as three dimensional (3D) device elements in miniaturized ferroelectric random access memory (FRAM). In chapter 7, we report the synthesis of single crystalline 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 (PMN-PT) nanoparticles. PMN-PT nanoparticles were developed by a novel sol-gel method based on diol route. After partial calcination at 450oC/1h, PMN-PT powder morphology started transforming from pyrochlore to perovskite phase. It is interesting to note that this partially crystallized PMN-PT powder was unstable under electron beam and generated freestanding lead nanoparticles after absorbing energy from a focused electron beam. PMN-PT powder annealed at 700°C was fully transformed to perovskite phase and was stable under electron beam. XRD calculations and TEM imaging confirmed the nanocrystalline nature of PMN-PT particles. Magnetic measurements on PMN-PT nanoparticles prepared at 650 and 750oC show room temperature ferromagnetic hysteresis, whereas the bulk or the agglomerated particles show diamagnetic behavior. With an increase of annealing temperature or the particle size the magnetic moment decreases. PMN-PT nanotubes with diameter about 200nm were fabricated successfully by the sol-gel method based on diol route within the closely packed porous nanochannel alumina templates. Phase purity and crystalline perovskite phase formation of PMN-PT nanotubes were confirmed by the XRD and SAED pattern. EDX analysis demonstrated that stoichiometry was formed within accepted limit. The wall of the nanotubes was found to be made of nanoparticles which were confirmed from the HRTEM analysis. The average thickness of the wall of the nanotube was found around 20 nm and nanoparticles consisting the wall were found to be in the range of 10-20 nm. Since electroceramic materials are following a similar trend to miniaturization as conventional semiconductors, the synthesis of nanosized oxidic building blocks is moving into the focus of scientific and technological interest. Ferroelectrics are promising class of materials for the fabrication of electronic devices, as they are already an integral part of modern nanotechnological operations. Chapter 8 deals with the synthesis and properties of BiFeO3 (BFO) nanoparticles and nanotubes. Single crystalline BFO nanoparticles of different size and polycrystalline BFO nanotubes were prepared by sol-gel method. As prepared nanostructures were characterized by various techniques such as XRD, TGA-DTA, FTIR, scanning electron microscope (SEM), transmission electron microscope (TEM), selected-area electron diffraction (SAED), high resolution TEM and energy-dispersive X-ray spectroscopy (EDX). The crystallinity and phase purity of the BFO nanoparticles and nanotubes were confirmed by the XRD, SAED pattern and HRTEM analysis. Compositional homogeneity and their crystalline structure confirms the formation of the rhombohedrally distorted perovskite phase. EDX analysis demonstrated that stoichiometric BiFeO3 was formed within accepted limit. The HRTEM analysis confirmed that wall of the BFO nanotubes was made of nanoparticles, which were randomly oriented in the wall. The average thickness of the wall of the nanotubes was found to be around 15 nm and nanoparticles consisting the wall were found to be in the range of 3-6nm. Formation of Y-junctions in this complex functional oxide was observed. Magnetic measurements show clearly the enhancement of ferromagnetism in BFO nanotubes and ferroelectric loops were also observed in these nanotubes, that indicates the multiferroic nature of these nanotubes. BFO nanostructures at a large scale might be important for many applications such as memory elements in nanoscale devices in future. Chapter 9 reports the synthesis of a series of crystalline La1-xCaxMnO3 (x = 0, 0.3, 0.5, 0.7) nanoparticles with average diameter about 20 nm by an improved sol-gel method. The crystallinity and phase formation of as prepared nanoparticles was confirmed via XRD, SAED and HRTEM studies. EDX analysis demonstrated that desired stoichiometric was formed. Magnetic characterization reveals that the PM-FM transitions (Tc) occurs around at 205, 235, 235 and 230 K for x = 0, 0.3, 0.5, 0.7, respectively. The strong irreversibility between zero field cooling (ZFC) and field cooling (FC) magnetization curves, a cusplike peak in ZFC curve and unusual shape of M versus H loop at T = 5 K gives strong support for surface spin glass behavior. The highly stable charge ordering state in bulk manganites is suppressed, while the ferromagnetism is enhanced in these nanoparticles (x = 0.5 and 0.7). La0.7Ca0.3MnO3 were fabricated by sol-gel method within the closely packed porous alumina templates. The wall of the nanotubes was found to be made up of randomly oriented nanoparticles (8-12nm) as confirmed by HRTEM studies. The strong irreversibility between ZFC and FC magnetization curves as well as a cusplike peak in ZFC curve gives strong support for surface spin glass behavior. Magnetization value as obtained from M-H loop was about 28.5% of expected value, suggesting the existence of a magnetic dead layer, which avoids the propagation of exchange interaction between magnetic grains. The PM-FM transition was observed at 235 K. Chapter 10 gives the summary and conclusions of the present study and also discusses the possible future work that could after more insights into the understanding of the perovskite nanostructures. Highlight of the present work (i) Successful growth of nanostructures in both particles and tube forms, and study of their structure – composition correlations. (ii) Present work could optimize the necessary chemistry to successfully grow nanoparticles and nanotubes of various perovskite compositions. (iii) Successful studies of physical properties of nanoparticles and nanotubes, ofcourse, to a limited extent. However the properties observed in the present nanostructures have a strong indication of nonlinear phenomena similar to their bulk counterparts. (iv) It was reported in the literature, the observation of ferromagnetic behavior in several nonmagnetic compositions at nano-scale. Surprisingly, similar ferroelectric behavior was noticed even in our perovskite complex oxides such as relaxors (PMN-PT). A clear interaction of magnetic spin and an electric dipole was evident in these oxides such as relaxors and also multiferroics at nano-scale (~10-20 nm). (v) In ferromagnetic compositions such as LCMO, a very interesting spin-glass type behavior was observed.

The extensive growth of nanotechnology has necessitated the development of economical and robust methods for large scale production of nanomaterials. It requires detailed quantitative understanding of lab-scale processes to enable effective scale-up and development of new contacting strategies for their controlled synthesis. In this thesis, attempts are made in both the directions using experimental and modelling approaches for synthesis of different nanoparticles. The two-phase Brust--Schiffrin protocol for the synthesis of gold nanoparticles was investigated first. The mechanism of transfer of reactants from aqueous to organic phase using phase transfer catalyst (PTC) was investigated using the measurement of interfacial tension, viscosity, SLS, SAXS, 1H NMR, DOSY-NMR, and Karl-Fischer titration. The study shows that the reactants are transferred to organic phase through the formation of hydrated complexes between reactants and PTC rather than through the solubilization of reactants in water core of inverse micelles of PTC, proposed recently in the literature. The particle synthesis reactions thus occur in the bulk organic phase. The extensive body of seemingly disparate experimental findings on Brust--Schiffrin protocol were put together next. The emerging picture ruled out both thermodynamic considerations and kinetics based arguments as exemplified by the classical LaMer's mechanism with sequential nucleation growth capping for size control in Brust--Schiffrin protocol. A new model for particle synthesis was developed. The model brought out continued nucleation--growth--capping based size control, an hitherto unknown mechanistic route for the synthesis of monodisperse particles, as the main mechanism. The model not only captured the reported features of the synthesis but also helped to improve the uniformity of the synthesized particles, validated experimentally. The two-step mechanism of Finke--Watzky---first order nucleation from precursor and autocatalytic growth of particles---proposed as an alternative to LaMer model to explain an induction period followed by a sigmoidal decrease in precursor concentration for the synthesis of iridium nanoparticles was investigated next. The mechanism is tested using an equivalent population balance model for its ability to explain the experimentally observed near constant breadth of the evolving size distribution as well. The predictions show that while it captures precursor conversion well, it fails to explain particle synthesis on account of its inability to suppress nucleation. A minimal four-step mechanism with additional steps for nucleation from reduced iridium atoms and their scavenging using particle surface is proposed. The new mechanism when combined with the first or second order nucleation, or classical nucleation with no scavenging of reduced atoms also fails to suppress nucleation. A burst like onset of nuclei formation with homogeneous nucleation and the scavenging of reduced atoms by particles are simultaneously required to explain all the reported features of the synthesis of iridium nanoparticles. A new reactor is proposed for continuous production of CaCO3 nanoparticles in gas-liquid reaction route. The key feature of the new reactor is the control of flow pattern to ensure efficient mixing of reactants. A liquidliquid reaction route for production of CaCO3 nanoparticles is also optimized to produce nanoparticles at high loading. Optimum supersaturation combined with efficient breakup of initial gel-like structure by mechanical agitation and charge control played a crucial role in producing nano sized CaCO3 particles.

Carbon nanoparticles (CNPs) have drawn great attention in the last few years owing to their unique properties such as excellent water solubility, chemical stability, inertness, low toxicity, good bio-compatibility, and tunable photo physical properties. Recently, researchers have focused on hetero atom (N, S and B) doped CNPs due to their excellent properties. These properties make the CNPs and doped CNPs as potential candidates for a wide range of applications. For example, metal ion detection in aqueous solution, bio-imaging, bio-sensing, photovoltaic devices, cleavage of deoxyribonucleic acid (DNA), and catalysis. Therefore, CNPs are alternative to inorganic semiconductor nanoparticles. However, CNPs with diameter less than 10 nm have been prepared using various approaches including top down and bottom methods. Cutting the bulk carbon from high dimensional to zero dimensional by using either physical or chemical process are classified as top down method. Bottom up method refers the conversion of organic precursor to nano-carbon by using thermal pyrolysis, microwave based hydrothermal method, cage opening of C60 molecules. In the present work, I have dealt with the facile synthesis of CNPs and different hetero atom doped carbon nanoparticles (N-CNPs, B-CNPs, and BN-CNPs) using the hydrothermal method. Based on their intriguing physical and chemical properties, these CNPs/doped-CNPs have been explored for various applications such as (i) metal-free catalysts, (ii) color tunability from red to blue and bio-imaging, (iii) ammonia sensing, (iv) white light generation, and (v) detection of picric acid (PA) in aqueous solution. Finally, I have presented 3D nanodendrites of N-CNPs and Pd NPs and their excellent catalytic mass activity for methanol electro-oxidation and ultra-fast reduction of 4-nitrophenol.

In this thesis, the results pertaining to various investigations carried out on Triglycine sulphate (TGS) single crystals, polyvinylidene fluoride (PVDF) films, lithium tantalate (LT)/PVDF nanocomposites and LT thin films are presented with emphasis on the characteristics that are crucial for their use in pyroelectric sensors. TGS single crystals (size 68 x 45 x 42 mm3), which have high pyroelectric coefficients, were grown by slow cooling method using newly designed platform technique based crystal growth work stations. The problem of slow growth rate along c-direction was overcome by placing (010) oriented seeds on the platform. The grown TGS crystals were used for the fabrication of the laser energy meter and temperature sensor. One drawback of TGS is its low Curie temperature (490C). As a consequence when the operating temperature approaches the Curie temperature, the crystals start depolarizing owing to the movement of domains. As a result the linearity of the devices gets affected and restricts the use of TGS. Therefore pyroelectric materials possessing higher Curie temperatures and larger pyroelectric coefficients than that of TGS are desirable. LT in single crystalline form having Curie temperature of ≈6000C has already been in use for pyroelectric device applications. However, growing stoichiometric LT single crystal is very difficult. On the other hand PVDF polymer films (Tc≈1800C) have low pyrolectric coefficients and difficult to pole electrically. Therefore efforts were made to prepare LT/PVDF nanocrystal composites to increase the pyroelectric coefficient of PVDF and to reduce the poling field. Nanoparticles of LT were prepared using sol-gel route. Spherical nanoparticles of size 20-40nm were prepared from sol by adding oleic acid to it. These nanoparticles were characterized using XRD, TEM, DSC and Raman spectroscopy. PVDF films with large percentage of β-phase (ferroelectric phase) were fabricated from solutions prepared using dimethylsulphoxide (DMSO) solvent. PVDF films (30µm thick), embedded with 20-40nm sized nanocrystallites of LT were fabricated to utilize them for pyroelectric sensor applications. The ferroelectric and pyrolectric properties of nano composite films were studied for sensor applications point of view. As a replacement for the single crystals of LT in pyroelectric sensors, investigations were carried out on oriented LT thin films. The studies on LT thin films yielded promising results which could be exploited for pyroelectric sensor applications.

Surfactant bound stable colloids of Au, Ag, and Pd were prepared by the solvated Metal Atom Dispersion (SMAD) method, a method involving co-condensation of metal and solvent vapors on the walls of a reactor at 77 k. The as=prepared dodecanethiol-capped Au and Ag colloids consisting of polydisperse nanoparticles were transformed into colloids consisting of highly monodisperse nanoparticles by the digestive ripening process. In the case of Pd colloids, digestive ripening led to the formation of thiolate complexes. The [Pd(SC12H25)2]6 complex formed from the dodecanethiol-capped Pd nanoparticles was found to be a versatile precursor for the synthesis of a variety of Pd nanophases such as Pd(0), PdS, and Pd@PdO by soventless thermolysis. Co-digestive ripening of as-prepared dodecanethiol-capped Au or Ag colloids with Pd colloid resulted in Au@Pd and Ag@Pd core-shell nanoparticles, respectively; attempts to transform the core-shell structures into alloy phases even at high temperatures were unsuccessful. Phosphine-capped Au nanoparticles were also prepared by the SMAD method and refluxing of this colloid resulted in an Ostwald ripening process rather than the expected digestive ripening due to the labile nature of bound PPh3. The labile nature of the bound phosphine was studied using 31P NMR spectroscopy and utilized in the adsorption of CO. Palladium nanoparticles obtained from the SMAD Pd-butanone colloids and Pd@PdO nanoparticles prepared by the solventless thermolysis of Pd-dodecanethiolate complex were found to be good catalysts for the generation of H2 from AB via either hydrolysis and methanolysis. The active hydrogen atoms produced during the hydrolysis and methanolysis diffuse into the Pd lattice. It was also noticed that hydrogen atoms that were buried deep inside the Pd lattice cannot be removed completely by heating the sample even at 600°C. Wet chemical reduction method was employed for the synthesis of PVP capped, nearly monodisperse, spherical Ir nanoparticles which undergo a polymer driven self-assembly at 80°C to afford rectangular structures and interlinked particles.

Porous, conductive metallic nanostructures are required in several fields, such as energy conversion, low-cost sensors etc. This thesis reports on the development of an electrocatalytically active and conductive membrane for use in Polymer Electrolyte Membrane Fuel Cells (PEMFCs) and fabrication of low-cost substrates for Surface Enhanced Raman Spectroscopy (SERS). One of the main challenges facing large-scale deployment of PEMFCs currently is to fabricate a catalyst layer that minimizes platinum loading, maximizes eletrocatalytically active area, and maximizes tolerance to CO in the feed stream. Modeling the kinetics of platinum catalyzed half cell reactions occurring in a PEMFC using the kinetic theory of gases and incorporating appropriate sticking coefficients provides a revealing insight that there is scope for an order of magnitude increase in maximum current density achievable from PEMFCs. To accomplish this, losses due to concentration polarization in gas diffusion layers, which occur at high current densities, need to be eliminated. A novel catalyst design, based on a porous metallic nanostructure, which aims to overcome the limitations of concentration polarization as well as minimize the amount of platinum loading in PEMFCs is proposed. Fabrication steps involving controlled in-plane fusion of self-assembled arrays of core-shell gold-platinum nanoparticles (Au@Pt) is envisioned. The key steps involved being the development of a facile synthesis route to form Au@Pt nanoparticles with tunable platinum shell thicknesses in the 5 nm size range, the formation of large-scale 2D arrays of Au@Pt nanoparticles using guided self-assembly, and optimization of an RF plasma process to promote in-plane fusion of the nanoparticles to form porous, electrocatalytically active and electrically conductive membranes. This thesis consists of seven chapters. The first chapter provides an introduction into the topic of PEMFCs, some perspective on the current status of research and development of PEMFCs, and an outline of the thesis. The second chapter provides an overview on the methods used, characterization techniques employed and protocols followed for sample preparation. The third chapter describes the modelling of a PEMFC using the Kinetic theory of gases to arrive at an estimate of the maximum feasible current density, based on the kinetics of the electrocatalytic reactions. The fourth chapter presents the development of a simple protocol for synthesizing Au@Pt nanoparticles with control over platinum shell thicknesses from the sub monolayer coverage onwards. The results of spectroscopic and microscopic characterization establish the uniformity of coating and the absence of secondary nucleation. Chapter five describes the formation of a nanoporous, electrocatalytically active membrane by self-assembly to form bilayers of 2D arrays of Au@Pt nanoparticles and subsequent fusion using an RF plasma based process. The evolution of the electrocatalytic activity and electrical conductivity as a function of the duration of RF plasma treatment is monitored for Au@Pt nanoparticles with various extent of platinum coating. Spectroscopic, microscopic, electrical and cyclic voltammetry characterization of the samples at various stages were used to understand the structural evolution with RF plasma treatment duration and discussed. Next durability studies were carried out on the nanoporous, Au@Pt bilayer nanoparticle array with an optimum composition of Pt/Au atomic ratio of 0.88 treated to 16 minutes of argon plasma exposure. After this the novel catalyst membrane design of PEM fuel cell is revisited. Two different techniques are proposed so that the thin, nanoporous, metallic catalyst membrane achieves horizontal electronic resistance equivalent to that of the conventional gas diffusion layer with catalyst layer. The first technique proposes the introduction of gold coated polymeric mesh in between the thin, nanoporous, metallic catalyst membrane and bipolar plate and discusses the advantages. Later the gold coated polymeric mesh is introduced in a conventional membrane electrode assembly and efficiency of the polarization curves probed with and without the introduction of gold coated polymeric mesh. The second technique describes the results of fabrication of a nanoporous metallic membrane using multiple layers of 2D Au@Pt nanoparticle arrays at an optimum composition of Pt/Au atomic ratio of 0.88 to reduce the horizontal electronic resistance. Preliminary studies on the permeability of water through such membranes supported on a porous polycarbonate filter membrane are also presented. In chapter six, a simple reactive inkjet printing process for fabricating SERS active silver nanostructures on paper is presented. The process adapts a simple room temperature protocol, using tannic acid as the reducing agent, developed earlier in our group to fabricate porous silver nanostructures on paper using a commercial office inkjet printer. The results of SERS characterization, spectroscopic and microscopic characterizations of the samples and the comparison of the substrate’s long-term performance with respect to a substrate fabricated using sodium borohydride as the reducing agent is discussed. Preliminary findings on attempts to fabricate a conductive silver network using RF plasma induced fusion area also presented. Chapter seven provides a summary of the results, draws conclusions and a perspective on work required to accomplish the goals of incorporating the porous metallic nanostructures into PEMFCs.

Investigations on size dependent phase stability and transformations in isolated nanoparticles have gained momentum in recent times. Size dependent phase stability generates size specific particle microstructure which consequently yields size specific functionality. One important prerequisite for conducting studies on nanoparticles is their synthesis. A substantial amount of research effort has therefore been focused on devising methodologies for synthesizing nanoparticles with controlled shapes and sizes. The present thesis deals with both these two aspects: (a) synthesis of nanoparticles and (b) phase transformations in nanoparticles. The system chosen in this study is AuCu intermetallic nanoparticles. The choice of AuCu nanoparticle was due to the fact that the literature contains abundance of structural and thermodynamic data on Au–Cu system which makes it a model system for investigating size dependence of phase transformations. With respect to synthesis, the present thesis provides methodologies for synthesizing alloyed Au–Cu nanoparticles of different sizes, Au–Cu nano-chain network structures and uniform Au–Cu2S hybrid nanoparticles. For every type, results are obtained from a detailed investigation of their formation mechanisms which are also presented in the thesis. With respect to phase transformation, the thesis presents results on the size dependence of fcc to L10 transformation onset in Au–Cu nanoparticles under isothermal annealing conditions. The present thesis is divided into eight chapters. A summary of results and key conclusions of work presented in each chapter are as follows. The ‘introduction’ chapter (chapter I) describes the organization of the thesis. Chapter II (literature study) presents a review of the research work reported in the literature on the various methodologies used for synthesizing Au–Cu based nanoparticles of different shapes and sizes and on ordering transformation in AuCu nanoparticles. The chapter also presents a brief discussion on the reaction variables that control the process of nucleation and growth of the nanoparticles in solution. Chapter III titled ‘experimental details and instrumentation’ describes the synthesis procedures that were used for producing various nanoparticles in the present work. The chapter also briefly describes the various characterization techniques that were used to investigate the nanoparticles. The fourth chapter titled ‘synthesis and mechanistic study of different sizes of AuCu nanoparticles’ provides two different methodologies for synthesis, referred as ‘two-stage process’ and ‘two-step process’ that have been used for producing alloyed AuCu nanoparticles of different sizes (5, 7, 10, 14, 17, 25 nm). The ‘two-stage’ process involved sequential reduction of Au and Cu precursors in a one pot synthesis process. Whereas, the ‘two-step’ process involved a two-pot synthesis in which separately synthesized Au nanoparticles were coated with Cu to generate alloyed AuCu nanoparticles. In the two-stage synthesis process it was observed that by changing the total surfactant-to-metal precursor molar ratio, sizes of the alloyed AuCu nanoparticles can be varied. ‘Total surfactants’ here include equal molar amounts of oleic acid and oleylamine surfactants. Interestingly, it was observed that there exists a limitation with respect to the minimum nanoparticle size that can be achieved by using the two-stage process. The minimum AuCu nanoparticle size achieved using the two-stage synthesis process was 14 nm. Mechanism of formation of AuCu nanoparticles in the two-stage synthesis process was investigated to find out the reason for this size limitation and also to determine how the synthesis process can be engineered to synthesize alloyed AuCu nanoparticles with smaller (<14nm) sizes. Studies to evaluate mechanism of synthesis were conducted by investigating phase and size of nanoparticles present in the reaction mixture extracted at various stages of the synthesis process. Their studies revealed that (a) the nanoparticle formation mechanism in the two-stage synthesis process involves initial formation of Au nanoparticles followed by a heterogeneous nucleation and diffusion of Cu atoms into these Au rich seeds to form Au–Cu intermetallic nanoparticles and (b) by increasing the relative molar amount of the oleylamine surfactant, size of the initial Au seed nanoparticles can be further reduced from the minimum size that can be achieved in the case when equal molar amounts of oleylamine and oleic acid surfactants are used. The information obtained from the mechanistic study was then utilized to design the two-step synthesis process. In the two-step process, Au nanoparticles were synthesized in a reaction mixture containing only the oleylamine surfactant. Use of only oleylamine resulted in production of pure Au nanoparticles with sizes that were well below 10 nm. These Au nanoparticles were washed and dispersed in a solution containing Cu precursor. Introduction of a reducing agent into this reaction mixture led to the heterogeneous nucleation of Cu onto the Au seed particles and their subsequent diffusion into them to form alloyed AuCu nanoparticles with sizes of ~5, 7 and 10 nm. The study present in this chapter essentially signified that the surfactants used in the reaction mixture not only prevent nanoparticles from agglomerating in the final dispersion but also control their nucleation and growth and therefore can be used as a tool to tune nanoparticle sizes. The fifth chapter titled ‘size dependent onset of FCC-to-L10 transformations in AuCu alloy nanoparticles’ illustrates the effect of AuCu nanoparticle size on the onset of ordering under isothermal annealing conditions. Nanoparticles in this study were annealed in-situ in a transmission electron microscope. Samples were prepared by drop drying a highly dilute dispersion of as-synthesized nanoparticles onto an electron transparent TEM grid. Nanoparticles sitting on the TEM grid were well separated from each other to minimize particle sintering during the annealing operation. It was however observed that during the isothermal annealing, particle coarsening due to atomic diffusion was appreciable for 5 nm particles but negligible for 7 and 10 nm particles. Therefore for this study only 7 nm and 10 nm sized particles were considered. Onset of ordering was determined from the time when first sign of the diffraction spot, corresponding to the ordered phase, appears in the selected area electron diffraction pattern from a region containing large number of AuCu nanoparticles. Through a series of isothermal experiments it was observed that the time for onset of ordering increased with decrease in size of the nanoparticles. It is speculated that the delay in onset of ordering may be due to the fact that with a decrease in nanoparticle size the probability of a nanoparticle containing a fluctuation that shall generate a thermodynamically stable nuclei of the ordered phase decreases. A sharp interface between the ordered and the disordered phase inside the particle was also observed which suggested that the ordering transformation in as-synthesized fcc AuCu nanoparticles is a first order transformation. The sixth chapter titled ‘synthesis and characterization of Au1-xCux–Cu2S hybrid nanostructures: morphology control by reaction engineering’ provides a modified polyol method based synthesis strategy for producing uniform Au–Cu2S hybrid nanoparticles. Detailed compositional and structural characterization revealed that the hybrid nanoparticles are composed of cube shaped Au-rich, Au–Cu solid solution phase and hemispherical shaped Cu2S phase. Interestingly, the hemispherical Cu2S phase was attached to only one facet of the cube shaped phase. A study on the formation mechanism of hybrid nanoparticles was also conducted by characterizing specimens extracted from the reaction mixture at different stages of the synthesis process. The study revealed that the mechanism of formation of hybrid nanoparticles involved initial formation of isolated cube shaped pure Au nanoparticles and Cu–thiolate complex with a sheet morphology. With increase in time at 180°C, the Cu–thiolate complex decomposed and one part of the Cu atoms that were produced from the decomposition were utilized in forming the spherical Cu2S and other part diffused into the Au nanoparticles to form Au–Cu solid solution phase. The chapter also presents a study on the effect of dodecanethiol (DDT) on achieving the hemisphere-on-cube hybrid morphology. In this study it is illustrated that an optimum concentration of dodecanethiol is required both for achieving size and morphological uniformity of the participating phases and for their attachment to form a hybrid nanoparticle. The seventh chapter titled ‘synthesis of Au–Cu nano-chains network and effect of temperature on morphological evolution’ provides methodology for synthesizing fcc Au– Cu nano-chain network structures using polyvinylprrolidone (PVP) surfactant. It was observed that with increase in the molar amount of PVP in the reaction mixture, morphology of the as-synthesized product gradually changed from isolated nanoparticles to branched nano-chain like. The nano-chains contained twins which indicated an absence of continuous growth and possibility of growth by oriented attachment of initially formed Au–Cu nanoparticles. Both in-situ and ex-situ annealing of the nano-chains led to their decomposition into isolated nanoparticles of varying sizes. Annealing also caused fcc-to¬L10 phase transformation. Investigation of the wave length of perturbation leading to breaking of a nano-chain into particles indicated that the surface energy anisotropy affects the splitting of nano-chain network structure into nano-sized particles. The thesis ends with a last chapter where we have presented possible future extension of current work.