Perovskite oxides show wide range of applications in the area of magnetism, ferroelectricity, piezoelectricity, thermoelectricity, gas sensing, catalyst development, solid oxide fuel cell, etc. This is due to flexibility in the structure and compositions that can be tuned by specific element doping. In the perovskite oxide (ABO3), large cation (A) is 12 -coordinated and smaller B-cation is 6 coordinated with oxide ions. Oxide materials are considered as better candidates for thermoelectric applications (interconversion of thermal into electrical energy) due to its non-toxicity and thermal stability at elevated temperature. These are insulating in nature and the conductivity can be increased by doping A and / or B –sites. Perovskite oxides are also used for oxygen monitoring in different applications including control and optimization of combustion of fossil fuels in industries and automobiles, biological and defines places, etc. In the present study, we focused on thermoelectric properties in single perovskite oxides of lanthanum cobaltite and calcium manganite and a double perovskite oxide of dysprosium barium cobaltite. Also, the oxygen sensing behaviour of dysprosium barium cobaltite at elevated temperatures is studied. The thesis contains seven chapters and a summary of respective chapters are given below. The first chapter outlines the basics of thermoelectric and gas sensing applications of both perovskite and double perovskite oxides. In the initial part, thermoelectric phenomena are explained. Thermoelectric effect is the conversion of thermal energy to electrical energy and vice-versa. Higher thermoelectric efficiency (η) can be achieved by maintaining a large temperature difference across the material. The efficiency depends on the thermoelectric figure of merit (zT) of material, which depends on thermopower (S), electrical resistivity (ρ) and thermal conductivity (κ) of the material and hence needs to be optimized. The latter part discusses the oxygen sensing property of distorted double perovskite 112 structure type as it shows advantages over other materials due to oxygen nonstoichiometric. Further, an overview of the relevant literature, objective and scope of the thesis are mentioned. The second chapter elucidates the materials and methods used for the present work. The materials viz. LaCoO3, CaMnO3-δ and DyBaCo2O5+δ, were selected for thermoelectric and oxygen sensing studies. Both the conventional solid state and soft chemistry methods were adopted for the synthesis of these materials. Powders were densified into pellets by hot uniaxial pressing / cold isostatic pressing and various heat treatments were carried out. Samples thus prepared were phase pure as confirmed using powder x-ray diffraction and Rietveld refinement performed for structural analysis. Morphological studies were carried out using scanning electron microscopy and transmission electron microscopy. Further Raman and x-ray photoelectron spectroscopic characterization of these materials were discussed. The transport properties viz. electrical resistivity, thermopower and thermal conductivity of compact pellets were measured at elevated temperatures. Further, the home-built apparatus for room temperature See beck measurements and chemo resistive oxygen sensing were explained in detail as a part of this work. The third chapter describes the effect of monovalent ion doping (Na+ and K+) at A-site of lanthanum cobaltite on thermoelectric properties. Lanthanum cobaltite system exhibit exotic behaviour due to commensuration phenomena of spin, lattice, charge and metal insulator transition. The synthesis, followed by structural refinements by Rietveld method using Fullprof suit program are explained. The results of the transport properties indicate that there is no appreciable change in the See beck Coefficient of K-doped samples throughout the studied temperature range. The Na-doped samples exhibit a decrease in the Seebeck value with increasing Na content at room temperature. At higher temperatures Seebeck value matches with that of the parent sample. This may be due to a change in the ratio of the concentration of Co4+/Co3+ ions which increases the configurational entropy of the system. In conclusion, the highest figure of merit (0.01) found for the Na / K- doped lanthanum cobaltite is for 15 atomic wt. % of doping amongst the studied samples. The fourth chapter explains about Tb/Nb co-doped calcium manganite for thermoelectric applications. The CaMnO3-δ shows enhanced thermoelectric properties, exhibits n-type behavior and the absolute thermopower is found to be 129 µV/K. Here, we investigated the Terbium and Niobium codoped at Ca and Mn-sites respectively. The presence of oxygen non-stoichiometry was confirmed using Raman spectroscopy (Mn3+ peak at 614 cm-1) and δ value was evaluated by iodometric titration. The thermoelectric properties of cold isostatic pressed (CIP) pellets prepared by the solid state and soft chemistry routes are compared. The non-monotonous behavior of absolute thermopower may be due to the increase of Mn3+ in the Mn4+ matrix and also the presence of oxygen defects in compounds. The thermoelectric figure of merit of solid state sample CaMnO3-δ estimated of 0.036 at 825K. The fifth chapter describes the thermoelectric properties of double Perovskite AA’B2O6 (112 type): (RE)BaCo2O5+δ. It is a disordered double perovskite with non-stoichiometry in oxygen and exhibits mixed valences of Cobalt. Resistivity of DyBaCo2O5+δ was found to be 0.09 Ω cm and Seebeck coefficient is found to be 42 µV/K. In order to improve the thermopower value, the Fe is substituted at Co-site. This varies the valences of Cobalt that in turn leads to a higher thermopower. Also, the morphology of thermally etched CIP pellets recorded and correlated with the transport properties. It shows the highest thermoelectric figure of merit of 0.25 at 773 K for 20 at wt % of Fe substituted sample. The sixth chapter explains about oxygen sensing studies of DyBaCo2O5+δ (112 type). The detailed structural and morphological characterization studies were carried out. Thermogravimetric analysis at isothermal temperature 873 K shows fast intake/release of oxygen of this disordered double perovskite structure. The higher chemo resistive oxygen sensitivity at the elevated temperature was measured. Further, the systematic study on the effect of oxygen sensing on the substitution of Fe and Cu at Co-site in DyBaCo2-xM xO5+δ was investigated. The possible bulk diffusion mechanism at higher temperature due to movement of oxygen defects were explained. The highest sensitivity was obtained for x = 0.4 at % of Fe and 0.2 at % of Cu at 973 K and 823 K respectively. The key findings and future aspects are summarized in the chapter-7.

Transition metal compounds, especially the oxides, containing dn (0 ≤ n ≤ 10) electronic configuration, constitute the backbone of solid state/materials chemistry aimed at realization of novel materials properties of technological importance. Some of the significant materials properties of current interest are spin-polarized metallic ferromagnetism, negative thermal expansion, second harmonic nonlinear optical (NLO) susceptibility, fast ionic and mixed electronic/ionic conductivity for application in solid state batteries, and last but not the least, high-temperature superconductivity. Typical examples for each one of these properties could be found among transition metal oxides. Thus, alkaline-earth metal (A) substituted rare-earth (Ln) manganites, Lnı.xAxMnΟ3, are currently important examples for spin-polarized magnetotransport, ZrV2O7 and ZrW2O8 for negative thermal expansion coefficient, KTiOPO4 and LiNbO3 for second harmonic NLO susceptibility, (Li, La) TiO3 and LiMn2O4 for fast-ionic and mixed electronic/ionic conductivity respectively, and the whole host of cuprates typified by YBa2Cu3O7 for high Tc superconductivity. Solid state chemists constantly endeavour to obtain structure-property relations of solids so as to be able to design better materials towards desired properties. Synthesis coupled with characterization of structure and measurement of relevant properties is a common strategy that chemists adopt for this task. The work described in this thesis is based on such a broad-based chemists' approach towards understanding and realization of novel materials properties among the family of metal oxides. A search for metallic ferro/ferrimagnetism among the transition metal perovskite oxides, metallicity and possibility of superconductivity among transition-metal substituted cuprates and second order NLO susceptibility among metal oxides containing d° cations such as Ti(IV), V(V) and Nb(V) - constitute the main focus of the present thesis. New synthetic strategies that combine the conventional ceramic approach with the chemistry-based 'soft1 methods have been employed wherever possible to prepare the materials. The structures and electronic properties of the new materials have been probed by state-of-the art techniques that include powder X-ray diffraction (XRD) together with Rietveld refinement, electron diffraction, thermogravimetry, measurement of magnetic susceptibility (including magnetoresistance), Mossbauer spectroscopy and SHG response (towards 1064 nm laser radiation), besides conventional analytical techniques for determination of chemical compositions. Some of the highlights of the present thesis are: (i) synthesis of new mixed valent [Mn(III)/Mn(IV)] perovskite-type manganites, ALaMn2O6-y (A = K, Rb) and ALaBMn3O9_y (A = Na, K; B = Ca, Sr) that exhibit ferromagnetism and magnetoresistance; (ii) investigation of a variety of ferrimagnetic double-perovskites that include ALaMnRuO6 (A = Ca, Sr, Ba) and ALaFeVO6 (A = Ca, Sr) and A2FeReO6 (A = Ca, Sr, Ba) providing new insights into the occurrence of metallic and nonmetallic ferrimagnetic behaviour among this family of oxides; (iii) synthesis of new K2NiF4-type oxides, La2-2xSr2XCui.xMxO4 (M = Ti, Mn, Fe, Ru) and investigation of Cu-O-M interaction in two dimension and (iv) identification of the structural rnotif(s) that gives rise to efficient second order NLO optical (SHG) response among d° oxides containing Ti(IV), V(V), Nb(V) etc., and synthesis of a new SHG material, Ba2-xVOSi2O7 having the fresnoite structure. The thesis consists of five chapters and an appendix, describing the results of the investigations carried out by the candidate. A brief introduction to transition metaloxides, perovskite oxides in particular, is presented in Chapter 1. Attention is focused on the structure and properties of these materials. Chapter 2 describes the synthesis and investigation of two series of anion-deficient perovskite oxides, ALaMn2O6-y (A = K, Rb, Cs) and ALaBMn3O9_y (A = Na, K; B = Ca, Sr). ALaMn2O6-y (A = K, Rb, Cs) series of oxides adopt 2 ap x 2 ap superstructure for K and Rb phases and √2 av x √2 ap x 2 ap superstructure (ap = perovskite subcell) for the Cs phase. Among ALaBMn3O9-y phases, the A = Na members adopt a new kind of perovskite superstructure, ap x 3 ap, while the A = K phases do not reveal an obvious superstructure of the perovskite. All these oxides are ferromagnetic (Tc ~ 260-325 K) and metallic exhibiting a giant magnetoresistance behaviour similar to alkaline earth metal substituted lanthanum manganites, Lai_xAxMnO3. However, unlike the latter, the resistivity peak temperature Tp for all the anion-deficient manganites is significantly lower than Tc. In Chapter 3, we have investigated structure and electronic properties of double-perovskite oxides, A2FeReO6 (A = Ca, Sr and Ba). The A = Sr, Ba phases are cubic (Fm3m) and metallic, while the A = Ca phase is monoclinic (P2yn) and nonmetallic. All the three oxides are ferrimagnetic with Tcs 315-385 K as reported earlier. A = Sr, Ba phases show a negative magnetoresistance (MR) (10-25 % at 5 T), while the Ca member does not show an MR effect. 57Fe Mossbauer spectroscopy shows that iron is present in the high-spin Fe3+ (S = 5/2) state in Ca compound, while it occurs in an intermediate state between high-spin Fe2+ and Fe3+ in the Ba compound. Monoclinic distortion and high covalency of Ca-O bonds appear to freeze the oxidation states at Fe+3/Re5+ in Ca2FeRe O6, while the symmetric structure and ionic Ba-O bonds render the FeReO6 array highly covalent and Ba2FeReO6 metallic. Mossbauer data for Sr2FeReO6 shows that the valence state of iron in this compound is intermediate between that in Ba and Ca compounds. It is likely that Sr2FeReO6 which lies at the boundary between metallic and insulating states is metastable, phase-seperating into a percolating mixture of different electronic states at the microscopic level. In an effort to understand the occurrence of metallicity and ferrimagnetism among double perovskites, we have synthesized several new members : ALaMnFeO6 (A = Ca, Sr, Ba), ALaMnRuO6 (A = Ca, Sr, Ba) and ALaVFeO6 (A = Ca, Sr) (Chapter 3). Electron diffraction reveals an ordering of Mn and Ru in ALaMnRuO6 showing a doubling of the primitive cubic perovskite cell, while ALaVFeO6 do not show an ordering. ALaMnRuOs are ferrimagnetic (Tcs ~ 200-250 K) semiconductors, but ALaVFeO6 oxides do not show a long range magnetic ordering . The present work together with the previous work on double perovskites shows that only a very few of them exhibit both metallicity and ferrimagnetism, although several of them are ferrimagnetic. For example, among the series Ba2MReO6 (M = Mn, Fe, Co, Ni), only the M = Fe oxide is both metallic and ferrimagnetic, while M = Mn and Ni oxides are ferrimagnetic semiconductors. Similarly, A2CrMoO6 (A = Ca, Sr), A2CrRe06 (A = Ca, Sr), and ALaMnRuO6 (A = Ca, Sr, Ba) are all ferrimagnetic but not metallic. While ferrimagnetism of double perovskites arise from an antiferromagnetic coupling of B and B' spins through the B-O-B' bridges, the occurrence of metallicity seems to require precise matching of the energies of d-states of B and B' cations and a high covalency in the BB'O6 array that allows a facile electron-transfer between B and B', Bn++B’m+↔B(n+1)++B’(m-1)+ without an energy cost, just as occurs in ReO3 and other metallic ABO3 perovskites. In an effort to understand the Cu-O-M (M = Ti, Mn, Fe, Ru) electronic interaction in two dimension, we have investigated K2N1F4 oxides of the general formula La2-2xSr2XCui.xMxO4 (M = Ti, Mn, Fe or Ru). These investigations are described in Chapter 4. For M = Ti, only the x = 0.5 member could be prepared, while for M = Mn and Fe, the composition range is 0 < x < 1.0, and for M = Ru, the composition range is 0 < x ≤ 0.5. There is no evidence for ordering of Cu(II) and M(IV) in the x = 0.5 members. While the members of the M = Ti, Mn and Ru series are semiconducting/insulating, the members of the M = Fe series are metallic, showing a broad metal-semiconductor transition around 100 K for 0 < x ≤ 0.15 that is possibly related to a Cu(II)-O-Fe(IV) < > Cu(III)-O-Fe(III) valence degeneracy. Increasing the strontium content at the expense of lanthanum in La2-2xSr2XCui.xFexO4 for x ≤ 0.20 renders the samples metallic but not superconducting. In a search for inorganic oxide materials showing second order nonlinear optical (NLO) susceptibility, we have investigated several borates, silicates and phosphates containing /ram-connected MO6 octahedral chains or MO5 square-pyramids, where M = d°: Ti(IV), Nb(V) or Ta(V). Our investigations, which are described in Chapter 5, have identified two new NLO structures: batisite, Na2Ba(TiO)2Si4O12, containing trans-connectd TiO6 octahedral chains, and fresnoite, Ba2TiOSi2O7, containing square-pyramidal T1O5. Investigation of two other materials containing square-pyramidal TiO5, viz., Cs2TiOP2O7 and Na4Ti2Si8O22. 4H2O, revealed that isolated TiO5 square-pyramids alone do not cause a second harmonic generation (SHG) response; rather, the orientation of T1O5 units to produce -Ti-O-Ti-O- chains with alternating long and short Ti-0 distances in the fresnoite structure is most likely the origin of a strong SHG response in fresnoite. Indeed, we have been able to prepare a new fresnoite type oxide, Ba2.xVOSi2O7 (x ~ 0.5) that shows a strong SHG response, confirming this hypothesis. In the Appendix, we have described three synthetic strategies that enabled us to prepare magnetic and NLO materials. We have shown that the reaction CrO3 + 2 NH4X > CrO2 + 2 NH3 + H2O + X2 (X = Br, I), which occurs quantitatively at 120-150 °C, provides a convenient method for the synthesis of CrO2. Unlike conventional methods, the method described here does not require the use of high pressure for the synthesis of this technologically important material. For the synthesis of magnetic double perovskites, we have developed a method that involves reaction of basic alkali metal carbonates with the acidic oxides (e.g. Re2O7) first, followed by reaction of this precursor oxide with the required transition metal/transition metal oxide (e.g. Fe/Fe2O3). By this method we have successfully prepared single-phase perovskite oxides, A2FeReO6, ACrMoO6 and ALaFeVO6. We have prepared the new NLO material Ba2_xV0Si207 from Ba2VOSi2O7 by a soft chemical redox reaction involving the oxidation of V(IV) to V(V) using Br2 in CH3CN/CHCI3. Ba2V0Si207 + 1/2 Br2 > Bai.5V0Si207 + 1/2 BaBr2. The work presented in this thesis was carried out by the candidate as part of the Ph.D. training programme. He hopes that the studies reported here will constitute a worthwhile contribution to the solid state chemistry of transition metal oxides and related materials.

The group of materials with ABO3 type perovskite structure are very important due to their attractive electrical and magnetic properties for technological applications and have been studied in the form of single crystals, bulk polycrystalline materials and thin films. Recently, efforts have been made to synthesize and understand the growth of ABO3 type perovskite nanostructures because of their distinctive physical properties and potential applications in the nanodevices. The primary aim of the present thesis is to synthesize the perovskites at nano-scale, with zero-dimension (0D), and one-dimension (1D) configurations. Basic work was carried in terms of synthesis – structure – composition correlation. Due to the small nature of the synthesized materials, few attempts were done to examine the physical properties, but to a limited extant. Efforts were also done to emphasize the structural behavior of nano perovskite in comparison with their bulk counterparts. Chapter 1 provides a brief introduction to perovskite materials and nanostructures, their technological applications and the fundamental physics involved. A brief review of the perovskite nanostructures both from fundamental science and technological point of view is provided. Finally the specific objectives of the current research are outlined. Chapter 2 deals with the experimental studies carried out in this thesis. It describes the methods used for the synthesis, experimental set up and the basic operation principles of various structural and physical characterizations such as X-ray diffraction (XRD), thermal analysis, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM), compositional analysis (EDX), focused ion beam (FIB), electrical and magnetic studies of the materials prepared. Chapter 3 describes the fabrication of porous anodic aluminum oxide (AAO) templates with different pore size, basic steps for synthesis of nanotubes and the possible growth mechanism of nanotubes in the AAO template. In chapter 4, we report the synthesis of ferroelectric Ba1-xSrxTiO3 (x = 0.0, 0.3) nanoparticles (diameter range: 20-40nm) and Ba1-xSrxTiO3 (x = 0.0, 0.4) nanotubes with diameter about 200nm by the sol-gel method. The Ba1-xSrxTiO3 nanostructures so obtained were characterized by number of techniques, including FE-SEM, XRD, DTA/TGA, FTIR spectroscopy, TEM, HRTEM as well as EDX and SAED. Formation of Y-junctions and multi-branches in Ba1-xSrxTiO3 nanotubes were also observed. The wall of the nanotubes were found to be made of randomly oriented nanoparticles which were confirmed from the HRTEM image. The average thickness of the wall of the nanotubes was found around 15(±5) nm and nanoparticles consisting the wall were found to be in the range of 5-10nm. Diffused phase transition (cubic to tetragonal), shifted to lower temperature side and leaky ferroelectric P–E loops were observed in Ba1-xSrxTiO3 (x = 0.0) ceramic prepared from nanoparticles. Curie temperature was observed at 120oC in the BT nanotube array as confirmed by the dielectric study. The P–E loops of as-prepared Ba1-xSrxTiO3 (x = 0.0) nanotube array were also measured and the hysteresis clearly demonstrates the room temperature ferroelectricity in the as prepared nanotubes, indicating these nanotube array is potential media as ferroelectric information storage. In chapter 5, we report the synthesis of single crystalline nanoparticles and polycrystalline nanotubes of Pb0.76Ca0.24TiO3 (PCT24) by sol-gel processing and characterized by various techniques. The crystallinity and phase purity of the PCT24 nanoparticles and nanotubes were confirmed by the XRD and SAED pattern. Compositional homogeneity and their crystalline structure confirms the formation of the tetragonal perovskite phase. The wall of the nanotubes was found to be made of nanoparticles which were confirmed from the HRTEM analysis. The average thickness of the wall of the nanotubes was found around 20nm and nanoparticles consisting the wall were found to be in the range of 5-8nm. Formation of some single crystalline PCT24 nanorods was also observed as confirmed by SAED and HRTEM analysis. Formations of Y-junctions and multi-branches in this complex functional oxide were observed. Dielectric measurements shows the diffuse phase transition and frequency dependence of Tm (temperature at which real part of dielectric constant shows maxima) suggesting the relaxor type behavior in the PCT24 ceramic prepared from nanoparticles. Polarization study was carried out on PCT24 nanotube array, which shows the ferroelectric nature at room temperature. Chapter 6 reports the synthesis and studies of PbZrO3 (PZ) nanoparticles and PbZr1-xTixO3 for x = 0.0, 0.48 and 1.0 nanotubes. PZ nanoparticles were prepared by a novel sol-gel method based on diol-based solution. Initially, PZ was crystallized with some intermediate m-Z and t-Z phases at 400-550oC and start transforming to orthorhombic at around 600oC and then finally transformed into pure orthorhombic PZ phase at about 700oC. XRD and TEM confirmed the nanocrystalline nature of PZ particles. Curie temperature in the PZ ceramic prepared from PZ nanoparticles was observed around at 205oC, which is lower as compared to the bulk (233oC). P–E hysteresis loops of PZ ceramic prepared from nanoparticles were measured at different applied voltages and single ferroelectric loops of leaky nature were observed rather than antiferroelectrics. The lead zirconate nanoparticles produced may have potential applications as materials used in microelectronics and microelectromechanical systems. PbZr1-xTixO3 for x = 0.0 (PZ), 0.48 (PZT48) and 1 (PT) nanotubes were fabricated by sol-gel method within the closely packed porous alumina templates and characterized by various techniques. The crystallinity of the PZ, PZT48 and PT nanotubes were confirmed via XRD and SAED studies. EDX analysis demonstrated that stoichiometry was formed. Formation of Y-junctions in this complex functional oxide was also observed. The wall of the nanotubes was found to be made up of randomly oriented nanoparticles, which were confirmed by the HRTEM studies and also by a typical SEM image. The average thickness of the wall of the nanotubes was found to be around 10-20nm and nanoparticles consisting the wall was found to be in the range of 3 – 8nm. The Curie temperature was observed at 220oC in the PZ nanotube array. For the first time, PLD has been employed for the synthesis of lead zirconate nanotubes using AAO template. Well-registered arrays of these nanotubes could function as three dimensional (3D) device elements in miniaturized ferroelectric random access memory (FRAM). In chapter 7, we report the synthesis of single crystalline 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 (PMN-PT) nanoparticles. PMN-PT nanoparticles were developed by a novel sol-gel method based on diol route. After partial calcination at 450oC/1h, PMN-PT powder morphology started transforming from pyrochlore to perovskite phase. It is interesting to note that this partially crystallized PMN-PT powder was unstable under electron beam and generated freestanding lead nanoparticles after absorbing energy from a focused electron beam. PMN-PT powder annealed at 700°C was fully transformed to perovskite phase and was stable under electron beam. XRD calculations and TEM imaging confirmed the nanocrystalline nature of PMN-PT particles. Magnetic measurements on PMN-PT nanoparticles prepared at 650 and 750oC show room temperature ferromagnetic hysteresis, whereas the bulk or the agglomerated particles show diamagnetic behavior. With an increase of annealing temperature or the particle size the magnetic moment decreases. PMN-PT nanotubes with diameter about 200nm were fabricated successfully by the sol-gel method based on diol route within the closely packed porous nanochannel alumina templates. Phase purity and crystalline perovskite phase formation of PMN-PT nanotubes were confirmed by the XRD and SAED pattern. EDX analysis demonstrated that stoichiometry was formed within accepted limit. The wall of the nanotubes was found to be made of nanoparticles which were confirmed from the HRTEM analysis. The average thickness of the wall of the nanotube was found around 20 nm and nanoparticles consisting the wall were found to be in the range of 10-20 nm. Since electroceramic materials are following a similar trend to miniaturization as conventional semiconductors, the synthesis of nanosized oxidic building blocks is moving into the focus of scientific and technological interest. Ferroelectrics are promising class of materials for the fabrication of electronic devices, as they are already an integral part of modern nanotechnological operations. Chapter 8 deals with the synthesis and properties of BiFeO3 (BFO) nanoparticles and nanotubes. Single crystalline BFO nanoparticles of different size and polycrystalline BFO nanotubes were prepared by sol-gel method. As prepared nanostructures were characterized by various techniques such as XRD, TGA-DTA, FTIR, scanning electron microscope (SEM), transmission electron microscope (TEM), selected-area electron diffraction (SAED), high resolution TEM and energy-dispersive X-ray spectroscopy (EDX). The crystallinity and phase purity of the BFO nanoparticles and nanotubes were confirmed by the XRD, SAED pattern and HRTEM analysis. Compositional homogeneity and their crystalline structure confirms the formation of the rhombohedrally distorted perovskite phase. EDX analysis demonstrated that stoichiometric BiFeO3 was formed within accepted limit. The HRTEM analysis confirmed that wall of the BFO nanotubes was made of nanoparticles, which were randomly oriented in the wall. The average thickness of the wall of the nanotubes was found to be around 15 nm and nanoparticles consisting the wall were found to be in the range of 3-6nm. Formation of Y-junctions in this complex functional oxide was observed. Magnetic measurements show clearly the enhancement of ferromagnetism in BFO nanotubes and ferroelectric loops were also observed in these nanotubes, that indicates the multiferroic nature of these nanotubes. BFO nanostructures at a large scale might be important for many applications such as memory elements in nanoscale devices in future. Chapter 9 reports the synthesis of a series of crystalline La1-xCaxMnO3 (x = 0, 0.3, 0.5, 0.7) nanoparticles with average diameter about 20 nm by an improved sol-gel method. The crystallinity and phase formation of as prepared nanoparticles was confirmed via XRD, SAED and HRTEM studies. EDX analysis demonstrated that desired stoichiometric was formed. Magnetic characterization reveals that the PM-FM transitions (Tc) occurs around at 205, 235, 235 and 230 K for x = 0, 0.3, 0.5, 0.7, respectively. The strong irreversibility between zero field cooling (ZFC) and field cooling (FC) magnetization curves, a cusplike peak in ZFC curve and unusual shape of M versus H loop at T = 5 K gives strong support for surface spin glass behavior. The highly stable charge ordering state in bulk manganites is suppressed, while the ferromagnetism is enhanced in these nanoparticles (x = 0.5 and 0.7). La0.7Ca0.3MnO3 were fabricated by sol-gel method within the closely packed porous alumina templates. The wall of the nanotubes was found to be made up of randomly oriented nanoparticles (8-12nm) as confirmed by HRTEM studies. The strong irreversibility between ZFC and FC magnetization curves as well as a cusplike peak in ZFC curve gives strong support for surface spin glass behavior. Magnetization value as obtained from M-H loop was about 28.5% of expected value, suggesting the existence of a magnetic dead layer, which avoids the propagation of exchange interaction between magnetic grains. The PM-FM transition was observed at 235 K. Chapter 10 gives the summary and conclusions of the present study and also discusses the possible future work that could after more insights into the understanding of the perovskite nanostructures. Highlight of the present work (i) Successful growth of nanostructures in both particles and tube forms, and study of their structure – composition correlations. (ii) Present work could optimize the necessary chemistry to successfully grow nanoparticles and nanotubes of various perovskite compositions. (iii) Successful studies of physical properties of nanoparticles and nanotubes, ofcourse, to a limited extent. However the properties observed in the present nanostructures have a strong indication of nonlinear phenomena similar to their bulk counterparts. (iv) It was reported in the literature, the observation of ferromagnetic behavior in several nonmagnetic compositions at nano-scale. Surprisingly, similar ferroelectric behavior was noticed even in our perovskite complex oxides such as relaxors (PMN-PT). A clear interaction of magnetic spin and an electric dipole was evident in these oxides such as relaxors and also multiferroics at nano-scale (~10-20 nm). (v) In ferromagnetic compositions such as LCMO, a very interesting spin-glass type behavior was observed.

Dans cette thèse, nous présentons des études théoriques de matériaux pérovskites sous con-trainte mécanique uniaxiale en combinant les calculs de premier principe DFT ainsi quela théorie phénoménologique de type Landau. Les pérovskites ABO3 forment une classetrès importante de matériaux fonctionnels, qui peuvent présenter un large éventail de pro-priétés (e.g., supraconductivité, magnétisme, ferroélectricité, multiferroïcité, transitionsmétal-isolant. . . ) grâce aux petites distorsions d’ une même structure prototype cubique.Bien que ces composés aient été largement étudiés expérimentalement et théoriquement, ilreste encore des questions importantes et non résolues concernant les effets de contraintesuniaxiales. Au cours de ces dernières années, l’ ingénierie de contrainte a été décrite commeune approche originale pour ajuster les propriétés ferroélectriques pérovskites ABO3. Alorsque les effets de tension épitaxié-biaxiale et pression la hydrostatique, sont plutôt bien com-pris dans cette classe de matériaux, très peu est connu en ce qui concerne l’ effet des con-traintes mécaniques uniaxiales. Notre étude est motivée par ce manque de compréhensionactuelle de l’ effet de tension et compression uniaxiale, qui a été jusqu’à présent presquetotalement négligé. Deux composés prototypes sont étudiés dans le détail: PbTiO3 etSrTiO3. Après une introduction générale sur les composés ABO3 et les calculs techniques(ab initio et modèle phénoménologique de Landau), nous avons étudié l’ effet de contraintesmécaniques sur ces matériaux dans notre thèse.PbTiO3 est un composé ferroélectrique prototypique et également l’ un des composantsmère de la solution solide Pb(Zr,Ti)O3 (PZT), qui est le piézoélectrique le plus largementutilisé dans des applications. Pour PbTiO3, nous avons montré que indépendammentde la contrainte mécanique uniaxiale appliquée, le système conserve un état fondamentalpurement ferroélectrique avec la polarisation alignée, soit le long de la direction de lacontrainte (en phase FEz) ou bien le long d’ un des axes pseudo-cubique, qui lui estperpendiculaire (phase de FEx). Cela contraste avec les cas de contraintes mécaniquesisotropes ou bi-axial, pour qui de nouvelles phases combinant des modes ferroélectriqueset antiferrodistortives ont déjà été décrites. Sous contrainte uniaxiale, PbTiO3 passe d’unétat fondamental FEx sous compression à un état fondamental FEz en tension au-delà d’une tension critique !czz! +1%. Sous contrainte uniaxiale, PbTiO3 présente soit un étatfondamental FEx sous compression ("zz < 0) ou un état fondamental de FEz sous tension("zz > 0). Cependant, ici, un brusque saut des paramètres structuraux est prévu sousdes contraintes de compression et de traction à des valeurs critiques "zz! +2 GPa et −8GPa. Ce comportement semble similaire à celui pré-prédit sous pression isotrope négativeet pourrait se révéler utile en pratique pour améliorer la réponse piézoélectrique dans lesnano-composants.Le deuxième composé intéressant est SrTiO3. Il a été largement étudié au cours desdernières décennies, en raison de ses propriétés exceptionnelles à basse température. Dansce travail, nous avons élargi nos précédentes études de PbTiO3, en explorant théorique-ment les effets de pression sur la perovskite SrTiO3, combinant les premiers principes decalculs et un modèle phénoménologique de type Landau. Nous avons discuté de l’évolutiondes fréquences des phonons de SrTiO3 des trois cas de contraintes isotrope, uniaxial ettensions biaxiaux en utilisant les calculs de premier principe. Nous confirmons des travauxexpérimentaux précédents sur SrTiO3 que ça soit en contrainte épitaxiée ou sous pressionhydrostatique. Enfin, nous avons calculé de diagramme de phase de SrTiO3 sous contrainteuniaxiale, obtenue à partir de la théorie de Landau que nous avons comparé aux calculsde premier principe. / In the present thesis we present theoretical studies of perovskite compounds under uniax-ial mechanical constraints combining first-principles DFT calculations approach and phe-nomenological Landau theory. ABO3 perovskites form a very important class of functionalmaterials that can exhibit a broad range of properties (e.g., superconductivity, magnetism,ferroelectricity, multiferroism, metal-insulator transitions. . . ) within small distortions ofthe same simple prototype cubic structure. Though these compounds have been exten-sively studied both experimentally and computationally, there are still unresolved issuesregarding the effect of pressure. In recent years, strain engineering has reported to bean original approach to tune the ferroelectric properties of perovskite ABO3 compounds.While the effect of epitaxial biaxial strain and hydrostatic strain is rather well understoodin this class of materials, very little is yet known regarding the effect of uniaxial mechanicalconstraints. Our study is motivated by the little existing understanding of the effect ofuniaxial strain and stress, that has been up to now almost totally neglected. Two proto-type compounds are studied in detail: PbTiO3 and SrTiO3. After a general introductionon ABO3 compounds and calculations techniques (ab initio and phenomenological Landaumodel), we studied the effect of mechanical constraints in these compounds in our thesis.PbTiO3 is a prototypical ferroelectric compound and also one of the parent components ofthe Pb(Zr,Ti)O3 solid solution (PZT), which is the most widely used piezoelectrics. ForPbTiO3, we have shown that irrespectively of the uniaxial mechanical constraint applied,the system keeps a purely ferroelectric ground-state, with the polarization aligned eitheralong the constraint direction (FEz phase) or along one of the pseudocubic axis perpen-dicular to it (FEx phase). This contrasts with the case of isotropic or biaxial mechanicalconstraints for which novel phases combining ferroelectric and antiferrodistortive motionshave been previously reported. Under uniaxial strain, PbTiO3 switches from a FEx groundstate under compressive strain to FEz ground-state under tensile strain, beyond a critical strain !czz! +1%. Under uniaxial stress, PbTiO3 exhibits either a FEx ground state undercompression ("zz < 0) or a FEz ground state under tension ("zz > 0). Here, however, anabrupt jump of the structural parameters is also predicted under both compressive andtensile stresses at critical values "zz! +2 GPa and −8 GPa. This behavior appears similarto that predicted under negative isotropic pressure and might reveal practically useful toenhance the piezoelectric response in nanodevices.The second compound of interest is SrTiO3. It has been widely studied in the past decadesdue to its unusual properties at low temperature. In this work, we have extended ourprevious investigations on PbTiO3 by exploring theoretically the pressure effects on per-ovskite SrTiO3 combining the first-principles calculations and a phenomenological Landaumodel. We have discussed the evolution of phonon frequencies of SrTiO3 with the threeisotropic, uniaxial and biaxial strains using first-principles calculations. We also reproducethe previous work done in SrTiO3 with epitaxial strain and hydrostatic strain. Finally,we have calculated the phase diagram of SrTiO3 under uniaxial strain, as obtained fromLandau theory and discussed how it compares with the first-principles calculations.

Transition metals (TMs) are ‘elements whose atoms have partially filled d-shell, or which can give rise to cations with an incomplete d-shell’. In TMs, the d-shell overlaps with next higher s-shell. Most of the TMs exhibit more than one (multiple) oxidation states. Some TMs, such as silver and gold, occur naturally in their metallic state but, most of the TM minerals are generally oxides. Most of the minerals on the planet earth are metal oxides, because of large free energies of formation for the oxides. The thermodynamic stability of the oxides is determined from the Ellingham diagram. Ellingham diagram shows the temperature dependence of the stability (free energy) for binaries such as metal oxides. Ellingham diagram also shows the ease of reducibility of metal oxides. TM oxides of general formulas MO, M2O3, MO2, M2O5, MO3 are known to exist, many of them being the ultimate products of oxidation in air in their highest oxidation states. In addition, TM oxides also exist in lower oxidation states which are prepared under controlled conditions. The nature of bonding in these oxides varies from mainly ionic (e.g. NiO, CoO) to mainly covalent (e.g. OsO4). Simple binary oxides of the compositions, MO, generally possess the rock salt structure (e.g. NiO), while the dioxides, MO2, possess the rutile structure (e.g. TiO2); many sesquioxides, M2O3, possess the corundum structure (e.g. Cr2O3). TMs form important ternary oxides like perovskites (e.g. CaTiO3), spinels (e.g. MgFe2O4) and so on. In TM oxides, the valence (outer) d-shell could be empty, d0 (e. g. TiO2), partially filled, dn (1≤ n≤ 9) (e.g. TiO, VO, NiO etc.) or completely filled, d10 (e.g. ZnO, CdO, Cu2O etc.). The outer d electrons in TM oxides could be localized or delocalized. Localized outer d electrons give insulators/semiconductors, while delocalized/itinerant d electrons make the TM oxide ‘metallic’ (e.g. ReO3, RuO2). Partially filled dn states are normally expected to give rise to itinerant (metallic) electron behaviour. But most of TM oxides with partially filled d shell are insulators because of special electronic energy (correlation energy) involved in d electron transfer to adjacent sites. Such insulating TM oxides are known as Mott insulators (e. g. NiO, CoO etc.). Certain TM oxides are known to exhibit both localized (insulating) and itinerant (metallic) behaviour as a function of temperature or pressure. For example, VO2 shows a insulator–metal transition at ~340K. Similar transitions are also known for V2O3, metal-rich EuO and so on. The chemical composition and bonding of TM oxides, which determine the crystal and electronic structures, give rise to functional properties. Table 1 gives representative examples. Properties like ionic conductivity and diffusion are governed by both the crystal structure and the defect structure (point defects), whereas properties such as magnetism and electron transport mainly arise from the electronic structures of the materials. Accordingly, TM oxides provide a platform for exploring functional materials properties. Among the various functional materials properties exhibited by transition metal oxides, the present thesis is devoted to investigations of lithium ion battery cathodes, inorganic pigments and magnetic perovskites. Over the years, most of the lithium containing first row transition metal oxides of rock salt derived structure have been investigated for possible application as cathode materials in lithium ion batteries (LIBs). First major breakthrough in LIBs research was achieved by electrochemically deinserting and inserting lithium in LiCoO2. A new series of cathode materials for LIBs were prepared by incorporating excess lithium into the transition metal containing layered lithium oxides through solid solution formation between Li2MnO3–LiMO2 (M = Cr, Mn, Fe, Co, Ni), known as lithium-rich layered oxides (LLOs). LLOs exhibit improved electrochemical performance as compared to the corresponding end members and hence received significant attention as a potential next generation cathode materials for LIBs in recent times. LiCoO2 (R-3m) crystallizes in the layered α-NaFeO2 structure with the oxygens in a ccp arrangement. Li+ and Co3+ ions almost perfectly order in the octahedral sites (3a and 3b) to give alternating (111) planes of LiO6 and CoO6 octahedra. Table 1. Materials properties exhibited by representative TM oxides. Property Example(s) Ferroelectricity BaTiO3, PbTiO3, Bi4Ti3O12 Nonlinear Optical Response LiNbO3 Multiferroic response BiFeO3, TbMnO3 Microwave dielectric properties Ba3ZnTa2O9 Relaxor Dielectric Properties Pb3MgNb2O9, Colossal Magnetoresistance Tl2Mn2O7 Metallic ‘Ferroelectricity’ Cd2Re2O7 Superconductivity AOs2O6(A = K, Rb, Cs) Redox deinsertion/insertion of LiCoO2 lithium Photocatalysis/water splitting TiO2 Pigment Ca(1-x)LaxTaO(2-x)N1+x (yellow-red), YIn1-xMnxO3 (blue) Metallic Ferromagnetism CrO2 Antiferromagnetism NiO, LaFeO3 Zero thermal expansion ZrW2O8 The reversible capacity of LiCoO2 in common LIBs is relatively low at around 140 mA h g-1 (half of theoretical capacity), corresponding to: LiCo3+O2 → Li0.5Co3+0.5Co4+0.5O2 + 0.5Li+ + 0.5e– . Substitution of one or more transition metal ions in LiCOO2 has been explored to improve the electrochemical performance. The structure of LLOs is described as a solid solution or nano composite of Li2MnO3 (C2/m) and LiMO2 (R-3m). The electrochemical deinsertion/insertion behaviour of LLOs is complex and also not yet understood completely. The present thesis consists of four parts. After a brief introduction (Part 1), Part 2 is devoted to materials for Li-ion battery cathode, consisting of three Chapters 2.1, 2.2 and 2.3. In Chapter 2.1, we describe the synthesis, crystal structure, magnetic and electrochemical characterization of new LiCoO2 type rock salt oxides of formula, Li3M2RuO6 (M = Co, Ni). The M =Co oxide adopts the LiCoO2 (R-3m) structure, whereas the M = Ni oxide also adopts a similar layered structure related to Li2TiO3. Magnetic susceptibility measurements reveal that in Li3Co2RuO6, the oxidation states of transition metal ions are Co3+, Co2+ and Ru4+, whereas in Li3Ni2RuO6, the oxidation states are Ni2+ and Ru5+. Li3Co2RuO6 orders antiferromagnetically at ~10K. On the other hand, Li3Ni2RuO6 presents a ferrimagnetic behaviour with a Curie temperature of ~100K. Electrochemical Li-deinsertion/insertion studies show that high first charge capacities (between ca.160 and 180 mA h g−1) corresponding to ca.2/3 of theoretical capacity are reached albeit, in both cases, capacity retention and cyclability are not satisfactory. Chapter 2.2 presents a study of new ruthenium containing LLOs, Li3MRuO5 (M = Co and Ni). Both the oxides crystallize in the layered LLO type LiCoO2 (α-NaFeO2) structure consisting of Li[Li0.2M0.4Ru0.4]O2 layers. Magnetic susceptibility data suggest that the oxidation states of transition metals are Li3Co3+Ru4+O5 for the M = Co compound and Li3Ni2+Ru5+O5 for the M = Ni compound. Electrochemical investigations of lithium deintercalation–intercalation behaviour reveal that both Co and Ni phases exhibit attractive specific capacities of ca. 200 mA h g-1 at an average voltage of 4 V, that has been interpreted as due to the oxidation of Co3+ and Ru4+ in Li3CoRuO5 and Ni2+ to Ni4+ in the case of Li3NiRuO5. Thus, we find that ruthenium plays a favourable role in LLOs than in non-LLOs in stabilizing higher reversible electrochemical capacities. In Chapter 2.3, we describe the synthesis, crystal structure and lithium deinsertion–insertion electrochemistry of two new LLOs, Li3MRuO5 (M=Mn, Fe) which are analogs of the oxides described in Chapter 2.2. The Li3MnRuO5 oxide adopts a structure related to Li2MnO3 (C2/m), while the Li3FeRuO5 oxide adopts a near-perfect LiCoO2 (R-3m) structure. Lithium electrochemistry shows typical behaviour of LLOs for both oxides, where participation of oxide ions in the electrochemical processes is observed. A long first charge process with capacities of 240 mA h g-1 (2.3 Li per f.u.) and 144 mA h g-1 (1.38 Li per f.u.) is observed for Li3MnRuO5 and Li3FeRuO5, respectively. Further discharge–charge cycling points to partial reversibility. X-ray photoelectron spectroscopy (XPS) characterisation of both pristine and electrochemically oxidized Li3MRuO5 reveals that in the Li3MnRuO5 oxide, Mn3+ and Ru4+ are partially oxidized to Mn4+ and Ru5+ in the sloping region at low voltage, while in the long plateau, O2- is also oxidized. In the Li3FeRuO5 oxide, the oxidation process appears to affect only Ru (4+ to 5+ in the sloping region) and O2- (plateau), while Fe seems to retain its 3+ state. Another characteristic feature of TMs is formation of several coloured solid materials where d–d transitions, band gap transitions and charge transfer transitions are involved in the colouration mechanism. Coloured TM oxides absorbing visible light find important applications as visible light photocatalyst (for example, yellow BiVO4 for solar water splitting and red Sr1-xNbO3 for oxidation of methylene blue) and inorganic pigments [for example, Egyptian blue (CaCuSi4O10), Malachite green (Cu2CO3(OH)2), Ochre red (Fe2O3)]. Pigments are applied as colouring materials in inks, dyes, paints, plastics, ceramic glazers, enamels and textiles. In this thesis, we have focused on the coloured TM oxides for possible application as inorganic pigments. Generally, colours arise from electronic transitions that absorb visible light. Colours of the inorganic pigments arise mainly from electronic transitions involving TM ions in various ligand fields and charge transfer transitions governed by different selection rules. The ligand field d–d transitions are parity forbidden but are relaxed due to various reasons, such as distortion (absence of center of inversion) and vibronic coupling. The d-electrons can be excited by light absorption in the visible region of the spectrum imparting colour to the material. Charge transfer transitions in the visible region are not restricted by the parity selection rules and therefore give intense colours. Here we have investigated the colours of manganese in unusual oxidation state (Mn5+) as well as the colours of different 3d-TM ions in distorted octahedral and trigonal prismatic sites in appropriate colourless crystalline host oxides. These results are discussed in Part 3 of the thesis. In Chapter 3.1, we describe a blue/green inorganic material, Ba3(P1−xMnxO4)2 (I) based on tetrahedral Mn5+O4 :3d2 chromophore. The solid solutions (I) which are sky-blue and turquoise-blue for x ≤ 0•25 and dark green for x ≥ 0•50, are readily synthesized in air from commonly available starting materials, stabilizing the Mn5+O4 chromophore in an isostructural phosphate host. We suggest that the covalency/ionicity of P–O/Mn–O bonds in the solid solutions tunes the crystal field strength around Mn(V) such that a blue colour results for materials with small values of x. The material could serve as a nontoxic blue/green inorganic pigment. In Chapter 3.2, an experimental investigation of the stabilization of the turquoise-coloured Mn5+O4 chromophore in various oxide hosts, viz., A3(VO4)2 (A = Ba, Sr, Ca), YVO4, and Ba2MO4 (M = Ti, Si), has been carried out. The results reveal that substitution of Mn5+O4 occurs in Ba3(VO4)2 forming the entire solid solution series Ba3(V1−xMnxO4)2 (0 < x ≤ 1.0), while, with the corresponding strontium derivative, only up to about 10% of Mn5+O4 substitution is possible. Ca3(VO4)2 and YVO4 do not stabilize Mn5+O4 at all. With Ba2MO4 (M = Ti, Si), we could prepare only partially substituted materials, Ba2M1−xMn5+xO4+x/2 for x up to 0.15, that are turquoise-coloured. We rationalize the results that a large stabilization of the O 2p-valence band states occurs in the presence of the electropositive barium that renders the Mn5+ oxidation state accessible in oxoanion compounds containing PO43−, VO43−, etc. By way of proof-of-concept, we synthesized new turquoise-coloured Mn5+O4 materials, Ba5(BO3)(MnO4)2Cl and Ba5(BO3)(PO4)(MnO4)Cl, based on the apatite – Ba5(PO4)3Cl – structure. Chapter 3.3 discusses crystal structures, and optical absorption spectra/colours of 3d-transition metal substituted lyonsite type oxides, Li3Al1-xMIIIx(MoO4)3 (0< x ≤1.0) (MIII = Cr, Fe) and Li3-xAl1-xMII2x(MoO4)3 (0< x ≤1.0) (MII = Co, Ni, Cu). Crystal structures determined from Rietveld refinement of PXRD data reveal that in the smaller trivalent metal substituted lyonsite oxides, MIII ions occupy the octahedral (8d, 4c) sites and the lithium ions exclusively occur at the trigonal prismatic (4c) site in the orthorhombic (Pnma) structure; on the other hand, larger divalent cations (CoII/CuII) substituted derivatives show occupancy of CoII/CuII ions at both the octahedral and trigonal prismatic sites. We have investigated the colours and optical absorption spectra of Li3Al1-xMIIIx(MoO4)3 (MIII = Cr, Fe) and Li3-xAl1-xMII2x(MoO4)3 (MII = Co, Ni, Cu) and interpreted the results in terms of average crystal field strengths experienced by MIII/MII ions at multiple coordination geometries. We have also identified the role of metal-to-metal charge transfer (MMCT) from the partially filled transition metal 3d orbitals to the empty Mo – 4d orbitals in the resulting colours of these oxides. B The ABO3 perovskite structure consists of a three dimensional framework of corner shared BO6 octahedra in which large A cation occupies dodecahedral site, surrounded by twelve oxide ions. The ideal cubic structure occurs when the Goldschmidt’s tolerance factor, t = (rA + rO)/{√2(rB + rO)}, adopts a value of unity and the A–O and B–O bond distances are perfectly matched. The BO6 octahedra tilt and bend the B – O – B bridges co-operatively to adjust for the non-ideal size of A cations, resulting deviation from ideal cubic structure to lower symmetries. Ordering of cations at the A and B sites of perovskite structure is an important phenomenon. Ordering of site cations in double (A2BB'O6) and multiple (A3BB'2O9) perovskites give rise to newer and interesting materials properties. Depending upon the constituent transition metals and ordering, double perovskite oxides exhibit a variety of magnetic behaviour such as ferromagnetism, ferrimagnetism, antiferromagnetism, spin-glass magnetism and so on. We also have coupled magnetic properties such as magnetoresistance (Sr2FeMoO6), magnetodielectric (La2NiMnO6) and magnetooptic (Sr2CrWO6) behaviour. Here we have investigated new magnetically frustrated double perovskite oxides of the formula Ln3B2RuO9(B = Co, Ni and Ln = La, Nd). The Chapter 4.1 describes Ln3B2RuO9 (B = Co, Ni and Ln = La, Nd) oxides (prepared by a solid state metathesis route) which adopt a monoclinic (P21/n) A2BB'O6 double perovskite structure, wherein the two independent octahedral 2c and 2d sites are occupied by B2+ and (B2+1/3Ru5+2/3) atoms, respectively. Temperature dependence of the molar magnetic susceptibility plots obtained under zero field cooled (ZFC) condition exhibit maxima in the temperature range 25–35K, suggesting an antiferromagnetic interaction in all these oxides. Ln3B2RuO9 oxides show spin-glass behavior and no long-range magnetic order is found down to 2 K. The results reveal the importance of competing nearest neighbour (NN), next nearest neighbor (NNN) and third nearest neighbour (third NN) interactions between the magnetic Ni2+/Co2+ and Ru5+ atoms in the partially ordered double perovskite structure that conspire to thwart the expected ferromagnetic order in these materials.

La cinétique lente de la réduction de l’oxygène (ORR) est en grande partie responsable de la perte d’énergie de nombreux systèmes de conversion tels que les piles à combustible. Parmi les possibles catalyseurs de l’ORR, les oxydes de type pérovskite sont des candidats prometteurs en milieu alcalin. La présente thèse est consacrée à l’étude de l’activité, du mécanisme et de la stabilité de pérovskites à base de Co et Mn pour l’ORR. Grâce aux techniques d’électrode tournante à disque et disque-anneau (R(R)DE), les études de l’ORR et des transformations d’HO2- sur les couches minces de pérovskite/carbone dans une solution de NaOH ont montré qu’O2 est réduit en OH- via un mécanisme « en série » avec formation d’HO2- intermédiaire. Pour des quantités d’oxyde suffisantes, HO2- est ensuite réduit, ce qui résulte en un mécanisme apparent de 4 électrons. Dans ces électrodes, le carbone joue un double rôle. Il augmente l’activité électrocatalytique en améliorant le contact électrique et il est impliqué dans le mécanisme de l’ORR en catalysant la réduction d’O2 en HO2-, surtout pour les pérovskites à base de cobalt qui sont considérablement moins actives que celles à base de Mn. Néanmoins, l’électrocatalyse de l’ORR semble dégrader les sites actifs des pérovskites. / The sluggish kinetics of the oxygen reduction reaction (ORR) is largely responsible for the energy losses in energy conversion systems such as fuel cells. Among possible inexpensive catalysts for the ORR, perovskite oxides are promising electrocatalysts in alkaline media. The present thesis is devoted to the investigation of the ORR activity, mechanism and stability of some Co and Mn-based perovskites. The rotating (ring) disk electrode (R(R)DE) studies of the ORR and the HO2- transformations on perovskite/carbon thin layers in NaOH electrolyte prove that O2 is reduced to OH- via a “series” pathway with the HO2- intermediate. For high oxide loadings, the formed HO2- species are further reduced to give a global 4 electron pathway. In these electrodes, carbon plays a dual role. It increases the electrocatalytic activity by improving the electrical contact and it is involved in the ORR mechanism by catalyzing the reduction of O2 into HO2-, especially for Co-based perovskites which display lower reaction rates than Mn-based perovskites.