In this thesis, we investigate a wireless communications system with distributed transmit antennas. Under such system scenario, the received signal has multiple carrier frequency offsets (CFOs) since each transmitter has its own oscillator, leading to serious inter-carrier interference (ICI) at the receiver end. Therefore, an ICI self-cancellation scheme is proposed in this thesis, where two different relay nodes use different sub-carriers. When the signals from different relay nodes are combined at the destination node, the ICI self-cancellation can be achieved. In addition, the quality of the received signal can be further improved if the residual CFO can be properly compensated. Traditionally, the medium value of the various CFOs is taken for compensation because of its simplicity. However, a medium value does not result in the optimal performance. In this thesis, a close form expression of optimal CFO is derived to maximize the average signal to interference power ratio. It is shown that the optimal CFO compensation is a function of channel state and individual CFOs. Simulation experiments are conducted to investigate the performance of the proposed scheme. It is shown that the system bit error rate can be substantially improved when the CFO is less than 0.3 subcarrier spacing.

High peak to average power ratio (PAPR) is one of the major drawbacks in orthogonal frequency division multiplexing (OFDM) systems. In recently years, various methods have been proposed to reduce the PAPR performance. The selected mapping (SLM) scheme is perhaps the most popular one because it provides outstanding PAPR reduction performance. In addition, the subcarrier magnitude remains the same in the SLM scheme. However, there are two major shortcomings in the SLM scheme. First of all, it requires a number of inverse fast Fourier transforms (IFFTs) to produce candidate signals, dramatically increasing the computational complexity. In addition, side information has to be transmitted to the receiver to indicate the candidate signal that results in the best PAPR, leading to the decrease in bandwidth utilization. To overcome these two drawbacks, this thesis proposes a novel SLM scheme that does not need side information. The proposed scheme is based on a low complexity SLM scheme [C.-P. Li, S.-H. Wang, and C.-L. Wang, ¡§Novel low-complexity SLM schemes for PAPR reduction in OFDM systems,¡¨ IEEE Trans. Signal Process., vol. 58, no. 5, pp. 2916¡V2921, May 2010] in pilot-aided OFDM system. Simulation experiments are conducted to verify the performance of the proposed scheme. It is shown that the bit error rate (BER) performance of the proposed scheme is very similar to that of the traditional SLM scheme with perfect knowledge of the side information. Therefore, the proposed scheme not only has the advantages of low complexity and high bandwidth utilization, but also has a superior BER performance.

The Orthogonal frequency division multiplexing (OFDM) technique has been intensively used in many wireless communication systems to achieve higher data rate transmissions. Due to the fact that the OFDM technique entails redundant block transmissions; the transmitted blocks suffer from the inter-symbol interference (ISI) and inter-block interference (IBI). To compensate this serious effect, in many literatures redundant symbols (or guard interval) with adequate length are inserted in the transmitted symbols to prevent the IBI. Also, in the receiver the equalizer can be employed to deal with ISI. In this thesis, we present a new pseudo random cyclic-postfix (PRCP-) OFDM associated with the multiple-input multiple-output (MIMO) antenna system configuration to further improve the system performance. In fact, the MIMO system can enhance channel capacity and achieve high data-rate. The above-mentioned PRCP-OFDM technique combines with the MIMO antennas system, through the appropriate model design can be used to combat the multi-path effect or the inter-block interference. As evident from the simulation results, the proposed ST-BC MIMO PRCP-OFDM system can avoid the interference of transmitted signals during the estimation of channel impulse response (CIR) with proposed cyclic-postfix sequences. In addition, to further improve and eliminate the residual IBI and ICI, the equalizer with the framework of the generalized sidelobe canceller (GSC) is considered. Specifically, when SNR grows, the proposed ST-BC MIMO PRCP-OFDM system can perform successfully in terms of symbol-error rate and semi-blind channel estimation. This is verified via the computer simulations.

The allocation of frequency spectrum by the FCC for Ultra Wideband (UWB) communications in the 3.1-10.6 GHz has paved the path for very high data rate Gb/s wireless communications. Frequency synthesis in these communication systems involves great challenges such as high frequency and wideband operation in addition to stringent requirements on frequency hopping time and coexistence with other wireless standards. This research proposes frequency generation schemes for such radio systems and their integrated implementations in silicon based technologies. Special emphasis is placed on efficient frequency planning and other system level considerations for building compact and practical systems for carrier frequency generation in an integrated UWB radio. This work proposes a frequency band plan for multiband OFDM based UWB radios in the 3.1-10.6 GHz range. Based on this frequency plan, two 11-band frequency synthesizers are designed, implemented and tested making them one of the first frequency synthesizers for UWB covering 78% of the licensed spectrum. The circuits are implemented in 0.25µm SiGe BiCMOS and the architectures are based on a single VCO at a fixed frequency followed by an array of dividers, multiplexers and single sideband (SSB) mixers to generate the 11 required bands in quadrature with fast hopping in much less than 9.5 ns. One of the synthesizers is integrated and tested as part of a 3-10 GHz packaged receiver. It draws 80 mA current from a 2.5 V supply and occupies an area of 2.25 mm2. Finally, an architecture for a UWB synthesizer is proposed that is based on a single multiband quadrature VCO, a programmable integer divider with 50% duty cycle and a single sideband mixer. A frequency band plan is proposed that greatly relaxes the tuning range requirement of the multiband VCO and leads to a very digitally intensive architecture for wideband frequency synthesis suitable for implementation in deep submicron CMOS processes. A design in 130nm CMOS occupies less than 1 mm2 while consuming 90 mW. This architecture provides an efficient solution in terms of area and power consumption with very low complexity.

Orthogonal frequency division multiplexing (OFDM) technique has been extensively used in digital wireless communications, such as Digital Broadcasting and wireless local area network (WLAN). It is considered to be one of the most promising techniques for transmission on the downlinks of broadband wireless access systems to combat multipath and multiple access interference (MAI). Spatial processing that exploits the diversity provided by smart antenna (SA) or intelligent antenna (IA) arrays, in which the adaptive beamformer is employed, is another alternatives to increase the efficiency of wireless system capacity and performance without allocating additional frequency spectrum. It allows the system to make full use of spatial diversity due to multiple antennas [5][6]. To further improve the performance for suppressing various interference sources; including narrowband and wideband interference, flat and frequency selective fading, for different channel environmentin. In this thesis, a smart antenna with wideband beamspace approach array beamformer associated with the slideing window (SW) linearly constrained RLS (SW-LC-RLS) algorithm, and the OFDM systems with smart antenna array are emhasized. Computer simulation results confirmed that our proposed scheme could achieve desired performance compared with the conventional approach, in terms of MAI and other interference suppression.

To satisfy the growing demands of the mobile and personal broadband communications, recently, many innovative technologies have been devised and extensively used for wireless transmission and reception. In the wireless communication systems, even though the performance would be degraded due to channel characteristics, such as multipath fading and background noise, those impacts can be eliminated dramatically through the utilization of diversity and combining. However, some different kinds of interfering sources, including the significant structure interference due to their operation as multiple access in the cellular communication systems, referred to as the multiple access interference (MAI), and inevitable jammers appeared in the overlapped frequency band for common utility, are still existing and now become the main difficulties to collapse the reception performance and system capacity. To suppress the interferences, some advanced signal processing methods, e.g., smart antenna (SA), multiuser detection, interference cancellation, adaptive optimization, and frequency/ frame synchronization, have been suggested to not only alleviate the effects fundamentally but also enhance the signal quality. Orthogonal frequency division multiplexing (OFDM) is a significant multicarrier (MC) technology, and has been widely employed in some commercial communications, such as digital broadcasting and wireless local area network (WLAN). It is considered to be the one of the most promising techniques to combat multipath fading and MAI for the downlinks transmission of the broadband systems. Moreover, spatial processing exploits the diversity provided by SA or intelligent antenna arrays, in which the adaptive beamformer is utilized, and it is an alternative approach to increase the efficiency of wireless system capacity and performance without allocating additional frequency spectrum. It allows the system to make full use of spatial diversity due to multiple antennas. In this dissertation, the wireless communications based on the OFDM technique and the applications of SA are considered. Also, an adaptive linearly constrained (LC) approach via inverse QR-decomposition (IQRD) recursive least-squares (RLS) algorithm is emphasized. The proposed LC-IQRD-RLS algorithm has the merits, such as numerical stability, fast convergence rate, and implementation efficiency, over the conventional adaptive algorithms. Furthermore, by incorporating with derivative constraint, the narrowband array could improve the robustness against to the wideband and coherent jammers. Here, the iterative quadratic maximum likelihood (IQML) algorithm with norm constraint set is utilized to estimate the jammer subspace. Computer simulations verify that the use of narrowband beamformer with an appropriate algorithm, e.g., LC-IQRD-RLS or IQML, could achieve the desired performance for jammer suppression. Next, their applications to the MC-CDMA system with frequency combining process will be fully addressed. In fact, the frequency diversity is achieved through the optimization approach, based on constrained minimum output energy (CMOE) criterion. Unfortunately, it is very sensitive to the signal mismatch due to channel estimation error. To deal with the mismatch problem, the invariant-property provided by constant modulus (CM) criterion along with the LC-IQRD-RLS algorithm is developed. Simulation results show that the frequency combiner with the robust LCCM IQRD-RLS algorithm could be used to recover the transmitted signal without channel mismatch or distortion, and mitigate the MAI efficiently even in the significant near-far effect environment. To further enhance the detection performance and increase system capacity, the space-time MC-CDMA receiver is proposed by combining the advantages of SA and multicarrier transmission technique. This direct fully space-time MC-CDMA receiver can be implemented via a mathematical operator, i.e., kronecker product. For further investigation, a theoretical analysis could be evaluated under certain assumptions to obtain a closed-form expression of bit error rate (BER). This will help us look more inside the impacts due to the numbers of subcarriers and array sensors. In the last chapter, the familiar problem of carrier frequency offset (CFO) is investigated following the standard of IEEE 802.11 a/g OFDM-based WLAN. The overall frequency synchronization scheme consists of three parts, viz., the coarse and fine automatic frequency control (AFC) circuits, and phase locked loop (PLL). With the proposed frequency synchronization scheme, it reserves 2dB power consumption compared with the current specification even some timing issues presented.

In recent years, the development of OFDM system has received a lot of attention. Some examples of existing systems where OFDM system is used are digital audio broadcasting, high-definition television terrestrial broadcasting, asymmetric digital subcarrier lines and so on. There are several reasons for using OFDM systems. First, OFDM system is an efficient way to deal with multipath effect. Under a fixed amount of delay spread, the implementation complexity of OFDM system is much less than that of single-carrier system. The reason is that OFDM system can simply use guard time to process delay spread without a complex equalizer. Second, OFDM system can achieve high data rate to transmit by using large number of subcarriers. Third, OFDM system can also efficiently combat with narrow band interference. On the other hand, OFDM system also has two main drawbacks. One is more sensitive to frequency offset, the other is higher PAPR. This thesis focuses on the PAPR problem. Pulse shaping method is an effective way to solve this problem. It can be used for any number of subcarriers of OFDM systems, so it is very flexible. It doesn¡¦t have any additional IFFTs in comparison to the selected mapping or partial transmit sequence method. Its implementation is simpler. And because it also doesn¡¦t distort the OFDM symbols, its bit error performance should be better than the clipping method. According to the pulse shaping method, we get a better waveform that can make the PAPR of OFDM symbols do not exceed about 2.

This research concerns analysis of system capacity, development of adaptive transmission schemes with known channel state information at the transmitter (CSIT) and design of new signal detection and channel estimation schemes with low complexity in some multiple antenna systems. We first analyze the sum-rate capacity of the downlink of a cellular system with multiple transmit antennas and multiple receive antennas assuming perfect CSIT. We evaluate the ergodic sum-rate capacity and show how the sum-rate capacity increases as the number of users and the number of receive antennas increases. We develop upper and lower bounds on the sum-rate capacity and study various adaptive MIMO schemes to achieve, or approach, the sum-rate capacity. Next, we study the minimum outage probability transmission schemes in a multiple-input-single-output (MISO) flat fading channel assuming partial CSIT. Considering two special cases: the mean feedback and the covariance feedback, we derive the optimum spatial transmission directions and show that the associated optimum power allocation scheme, which minimizes the outage probability, is closely related to the target rate and the accuracy of the CSIT. Since CSIT is obtained at the cost of feedback bandwidth, we also consider optimal allocation of bandwidth between the data channel and the feedback channel in order to maximize the average throughput of the data channel in MISO, flat fading, frequency division duplex (FDD) systems. We show that beamforming based on feedback CSI can achieve an average rate larger than the capacity without CSIT under a wide range of mobility conditions. We next study a SAGE-aided List-BLAST detection scheme for MIMO systems which can achieve performance close to that of the maximum-likelihood detector with low complexity. Finally, we apply the EM and SAGE algorithms in channel estimation for OFDM systems with multiple transmit antennas and compare them with a recently proposed least-squares based estimation algorithm. The EM and SAGE algorithms partition the problem of estimating a multi-input channel into independent channel estimation for each transmit-receive antenna pair, therefore avoiding the matrix inversion encountered in the joint least-squares estimation.

Design and analysis of random-like codes for various multiple-input and multiple-output communication systems are addressed in this work. Random-like codes have drawn significant interest because they offer capacity-achieving performance. We first consider the analysis and design of low-density parity-check (LDPC) codes for turbo multiuser detection in multipath CDMA channels. We develop techniques for computing the probability density function (pdf) of the extrinsic messages at the output of the soft-input soft-output (SISO) multiuser detectors as a function of the pdf of input extrinsic messages, user spreading codes, channel impulse responses, and signal-to-noise ratios. Using these techniques, we are able to accurately compute the thresholds for LDPC codes and design good irregular LDPC codes. We then apply the tools of density evolution with mixture Gaussian approximations to optimize irregular LDPC codes and to compute minimum operational signal-to-noise ratios for ergodic MIMO OFDM channels. In particular, the optimization is done for various MIMO OFDM system configurations which include different number of antennas, different channel models and different demodulation schemes. We also study the coding-spreading tradeoff in LDPC coded CDMA systems employing multiuser joint decoding. We solve the coding-spreading optimization based on the extrinsic information SNR evolution curves for the SISO multiuser detectors and the SISO LDPC decoders. Both single-cell and multi-cell scenarios will be considered. For each of these cases, we will characterize the extrinsic information for both finite-size systems and the so-called large systems where asymptotic performance results must be evoked. Finally, we consider the design optimization of irregular repeat accumulate (IRA) codes for MIMO communication systems employing iterative receivers. We present the density evolution-based procedure with Gaussian approximation for optimizing the IRA code ensemble. We adopt an approximation method based on linear programming to design an IRA code with the extrinsic information transfer (EXIT) chart matched to that of the soft MIMO demodulator.

Orthogonal frequency division multiplexing (OFDM) due to the robustness to the effect of multipath fading and having high spectral efficiency, it has become a good candidate of wireless communications systems. The block transmission of signal-blocks through the channel will suffer from the inter-block interference (IBI) and inter-symbol interference (ISI). Usually in the transmitter of the OFDM systems, redundancy (or guard interval), such cyclic prefix (CP) or zero padding (ZP), with sufficient length, is inserted in the transmitted block to avoid the IBI. In this thesis, we propose a novel pseudo random cyclic postfix (PRCP-) OFDM system configuration, which adopts the PRCP as redundancy and combines with multiple antennas. In fact, the multiple transmit antenna and multiple receive antenna, which exploits the spatial diversity, can be used to further enhance the channel capacity and achieve high data-rate. The main property of PRCP-OFDM modulation is that it exploits the cyclic-postfix sequences to estimate channel information with a low complexity method. Compared with CP-OFDM, it overcomes the channel null problem. For ZP-OFDM, it uses the additional information to estimate channel which is replaced by zero samples in ZP-OFDM. Moreover, PRCP-OFDM avoids the interference of signals to the desired postfix when we estimate channel impulse response (CIR) and which is different from pseudo random postfix (PRP-) OFDM [8]. Thus, as SNR grows, PRCP-OFDM can have better performance than PRP-OFDM. With the help of [9], [12] and [13], we extend the PRCP-OFDM to the MIMO case with space-time block coding. Via computer simulation, we verify that the performance is improved, in terms of the accuracy of channel estimation and symbol error rate (SER).