Germanium (Ge) is the most compatible semiconductor material with silicon-based complementary metal-oxide semiconductor technology, which has higher electron and hole mobility than Si, leading to enhanced device performance. In addition, semiconductor nanowires (NWs) have attracted significant attention as promising candidates for next-generation nanoscale devices. Due to their unique geometry and physical properties, NWs show excellent optical and electrical properties such as quantum size effects, enhanced light absorption, and high biological and chemical sensitivity. Furthermore, high response to light irradiation is one of the most significant properties of semiconductor NWs, which makes them excellent candidates for photodetectors. Hence, Ge NWs are promising high-mobility nanostructures for optoelectronic devices. Despite constant improvement in the performance of single NW-based devices, determining their electrical properties remains challenging. Here, a symmetric six-contact Hall bar configuration is developed for top-down fabricated highly doped Ge NWs with different widths down to 30 nm, which simultaneously facilitates Hall effect and four-probe resistance measurements. Furthermore, accurate control of doping and fabrication of metal contacts on n-type doped Ge NWs with low resistance and linear characteristics remain significant challenges in Ge-based devices. Therefore, a combined approach is reported to fabricate Ohmic contacts on n-type doped Ge NWs using ion implantation and rear-side flash lamp annealing. This approach allows the fabrication of axial p–n junctions along the single NWs with different widths. The fabricated devices demonstrated rectifying characteristics in dark conditions. The photoresponse of the axial p–n junction photodetectors was investigated under three different illumination wavelengths of 637 nm, 785 nm, and 1550 nm. Moreover, the fabricated axial p–n junction photodetector demonstrated a high-frequency response up to 1 MHz at zero bias.

The electrical properties of ZnO and contacts to ZnO have been investigated using different techniques. Temperature dependent Hall (TDH) effect measurements have been used to characterize the as-received melt grown ZnO samples in the 20 – 330 K temperature range. The effect of argon annealing on hydrogen peroxide treated ZnO samples has been investigated in the 200 – 800oC temperature range by the TDH effect measurement technique. The experimental data has been analysed by fitting a theoretical model written in Matlab to the data. Donor concentrations and acceptor concentrations together with the associated energy levels have been extracted by fitting the models to the experimentally obtained carrier concentration data by assuming a multi-donor and single charged acceptor in solving the charge balance equation. TDH measurements have revealed the dominance of surface conduction in melt grown ZnO in the 20 – 40 K temperature range. Surface conduction effects have proved to increase with the increase in annealing temperature. Surface donor volume concentrations have been determined in the 200 – 800oC by use of theory developed by D. C. Look. Good rectifying Schottky contacts have been fabricated on ZnO after treating the samples with boiling hydrogen peroxide. Electrical properties of these Schottky contacts have been investigated using current-voltage (IV) and capacitance-voltage (CV) measurements in the 60 – 300 K temperature range. The Schottky contacts have revealed the dominance of predominantly thermionic emission at room temperature and the existence of other current transport mechanisms at temperatures below room temperature. Polarity effects on the Schottky contacts deposited on the O-polar and Zn-polar faces of ZnO have been demonstrated by the IV technique on the Pd and Au Schottky contacts at room temperature. Results obtained indicate a strong dependence of the Schottky contact quality on the polarity of the samples at room temperature. The quality of the Schottky contacts have also indicated their dependence on the type of metal used with the Pd producing contacts with the better quality as compared to the Au. Schottky barrier heights determined using temperature dependent IV measurements have been observed to increase with increasing temperature and this has been explained as an effect of barrier inhomogeneities, while the ones obtained from CV measurements have proved to follow the negative temperature coefficient of the II – VI semiconductor material, i.e. a decrease in barrier height with increasing temperature. However, the values have proved to be larger than the energy gap of ZnO, an effect that has been explained as caused by an inversion layer. Copyright / Dissertation (MSc)--University of Pretoria, 2010. / Physics / unrestricted

Designs for deep ultraviolet (DUV) edge emitting laser diodes (LDs) based on the wurtzite III-nitride (III-N) material system are presented. A combination of proprietary and commercial advanced semiconductor LD simulation software is used to study the operation of III-N based DUV LDs theoretically. Critical factors limiting device performance are identified based on an extensive literature survey. A comprehensive design parameter space is investigated thoroughly with the help of advanced scripting capabilities. Several design strategies are proposed to eliminate the critical problems completely or partially. A DUV LD design is proposed based exclusively on AlInN active layers grown epitaxially on bulk AlN substrates because AlInN offers a promising alternative to AlGaN for the realization of LDs and LEDs operating in the DUV regime. The proposed AlInN-based design also features a tapered electron blocking layer (EBL) instead of a homogeneous one. Tapered EBLs redistribute the interfacial polarization charge volumetrically throughout the entire EBL thickness via compositional grading, and eliminate the parasitic inversion layer charge. AlGaN based DUV LD designs are explored also because at present, it may be difficult to grow AlInN epitaxially with superior crystalline quality. Polarization charge matching is proposed to improve electron and hole wavefunction overlap within the active region. Although the strategy of polarization charge matching has already been proposed in the literature to enhance performance of visible wavelength LEDs and LDs, the proposed design presents the first demonstration that polarization charge matching is also feasible for DUV LDs operating at sub-300 nm wavelengths. A lateral current injection (LCI) LD design is proposed featuring polarization-charge-matched barriers and regrown Ohmic contacts to avoid a group of issues related to the highly inefficient p-type doping of wide bandgap III-N materials in vertical injection designs. The proposed design partially decouples the problem of electrical injection from that of optical confinement. Although the idea of an LCI LD design has been proposed in the literature in the 90s to be used as longer wavelength active sources in optoelectronic integrated circuits using GaInAsP/InP and related material systems, the proposed design is the first theoretical demonstration that this concept can be applied to DUV LDs based on III-N material system. To solve the problem of hole transport in vertical injection designs, a DUV LD design based exclusively on AlGaN material system is presented, featuring an inverse-tapered p-waveguide layer instead of an EBL. Several EBL designs are investigated, and compared with conventionally-tapered EBL design. Through judicious volumetric redistribution of fixed negative polarization charge, inverse tapering may be exploited to achieve nearly flat valence band profiles free from barriers to hole injection into the active region, in contrast to conventional designs. Numerical simulations demonstrate that the inverse tapered strategy is a viable solution for efficient hole injection in vertical injection DUV LDs operating at shorter wavelengths (< 290 nm).

Ohmic contacts are crucial components in semiconductor devices such as transistors and diodes, and lowering their contact resistance is an important factor in device performance enhancement. This is especially important for low-noise amplifiers (LNAs) where device noise temperature decreases both directly and indirectly with decreasing contact resistance. This becomes relevant in quantum computers operated at cryogenic temperatures as LNAs constitutes the 4 K quantum bit (qubit) readout signal amplification chain. The goal of this project is to investigated the superconducting element niobium (Nb) as contact material for indium phosphide (InP) high-electron-mobility transistors (HEMTs), being the active component in cryogenic high-frequency LNAs. For contact and barrier resistance determination, test structures were fabricated and utilized according to the transfer length method(TLM) and the recess TLM respectively. Measurements were performed in room temperature as well as in cryogenic temperatures below and above Nb’s bulk transition temperature of 9.25 K. The results show low-resistance Nb-based ohmic contacts for n-In0.65Ga0.35As, with the non-alloyed Nb(50 nm)/Au(100 nm) stack yielding a room temperature contact resistivity of (9.4 ± 0.5) × 10−8 Ωcm2. For all contacts the contact resistivity increased moving to cryogenic temperatures, as expected when electron occupation of high-energy states decreases. At cryogenic temperatures nosuperconducting transition was observed, attributed to the Nb layer thickness being roughly equal to its coherence length. Considering the effective barrier resistance, the Ni/Ge/Au/Nb/Au alloyed contact had the lowest room temperature resistance, reporting 143 Ω µm. In cryogenic temperatures the effective barrier resistance unexpectedly decreased in all contacts. The Nb/Au contact showed the best cryogenic performance, with a barrier resistance of 28 − 37 Ω µm. This indicates great potential for non-alloyed Nb/Au contacts in cryogenic InP HEMTs. / Alla halvledarkomponenter, som dioder och transistorer, har ohmska kontakter. Att sänka kontaktresistansen hos de ohmska kontakterna är ett sätt att höja prestandan hos en komponent. Särskilt gäller detta för lågbrusförstärkare, som har en brustemperatur som minskar både direkt och indirekt med avtagande kontaktresistans. För kvantdatorer som måste kylas till kryogena temperaturer för att fungera är detta relevant eftersom förstärkningen av utläsningssignalen från kvantbitar sker via lågbrusförstärkare vid 4 K. Målet för detta examensprojekt är att undersöka ohmska kontakter baserade på det supraledande materialet niobium (Nb) i indiumfosfidbaserade högelektronmobilitetstransistorer, som är den aktivakomponenten i kryogena högfrekvens-lågbrusförstärkare. För bestämning av kontaktoch barriärresistans producerades teststrukturer enligt Transfer Length-metoden (TLM) respektive etsad TLM. Mätningar genomfördes i rumstemperatur samt vid kryogena temperaturer både över och under niobiumets kritiska temperatur på 9.25 K. Resultatet visar låg kontaktresistans för Nb-baserade ohmska kontakter på n-In0.65Ga0.35As. Den icke-legerade Nb(50 nm)/Au(100 nm)-kontakten hade en kontaktresistivitet på (9.4 ± 0.5) × 10−8 Ωcm2 . Vid kryogena temperaturer ökade kontaktresistansen för samtliga Nb-baserade kontakter, vilket är förväntat då färre elektroner fyller högenergitillstånd. Inget supraledande tillstånd observerades vid kryogena temperaturer, vilket kan förklaras av att tjockleken på niobiumlagret var ungefär lika med dess koherenslängd. Lägst barriärresistans vid rumstemperatur hade den legerade Ni/Ge/Au/Nb/Au-kontakten, med ett värde på 143 Ω µm. Vid kryogena temperaturer skedde en oväntad minskning hos barriärsresistansen hos samtliga kontakter, där den lägst barriärsresistans uppmättes på den icke-legerade Nb/Au-kontakten, 28 − 37 Ω µm. Slutsatsen som dras är att det finns stor potential för användning av icke-legerade Nb/Au-kontakter för kryogena lågbrusförstärkare baserade på indiumfosfid.