CuNi nanoparticles were synthesized using a new polyol synthesis method. Three different CuxNi1-x catalysts were synthesized where x = 20, 50 and 80. The nanoparticles were deposited on carbon, C, gamma-alumina, γ-Al2O3, yttria-stabilized zirconia, YSZ, and samariumdoped ceria, SDC. Each set of catalysts was tested using the Reverse Water Gas Shift, RWGS, reaction under atmospheric pressure and at temperatures ranging from 400°C-700°C. The experiments were repeated 3 times to ensure stability and reproducibility. Platinum nanoparticles were also deposited on the same supports and tested for the RWGS reaction at the same conditions. The CuNi nanoparticles were characterized using a variety of different techniques. Xray diffraction, XRD, measurements demonstrate the resence of two CuNi solid solutions: one Cu rich solid solution, and the other a Ni rich solid solution. X-ray photo electron spectroscopy, XPS, measurements show Cu enrichment on all catalytic surfaces. Scanning electron microscopy, SEM, measurements show CuNi nanoparticles ranging in size from 4 nm to 100 nm. Some agglomeration was observed. SDC showed the best yield with all catalysts. Furthermore, high oxygen vacancy content was shown to increase yield of CO for the RWGS reaction. Cu50Ni50/SDC shows the combination of highest yield of CO and the best stability among CuNi catalysts. It also has similar yields (39.8%) as Pt/SDC at 700°C, which achieved the equilibrium yield at that temperature (43.9%). The catalyst was stable for 48 hours when exposed to high temperatures (600-700°C). There was no CH4 observed during any of the experiments when the partial pressure of the reactant gases was fed stoichiometrically. Partial pressure variation experiments demonstrated the presence of CH4 when the partial pressure of hydrogen was increased to twice the value of the partial pressure of CO2.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第22159号 / 工博第4663号 / 新制||工||1727(附属図書館) / 京都大学大学院工学研究科材料工学専攻 / (主査)教授 田中 功, 教授 中村 裕之, 教授 邑瀬 邦明 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

京都大学 / 0048 / 新制・論文博士 / 博士(工学) / 乙第13240号 / 論工博第4178号 / 新制||工||1720(附属図書館) / (主査)教授 木本 恒暢, 教授 藤田 静雄, 教授 山田 啓文 / 学位規則第4条第2項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第18285号 / 工博第3877号 / 新制||工||1595(附属図書館) / 31143 / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 木本 恒暢, 教授 藤田 静雄, 准教授 掛谷 一弘 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

In this research we investigated the generation of methanol and the utilization of CO2 using heterogeneous catalysts. Heterogeneous catalysts are frequently used in industry due to their multiple benefits, which include long-term thermal and mechanical stability, as well as reusability. Our research has demonstrated a variety of heterogeneous catalysts for sustainable methanol production and CO2 utilization, including the novel dendritic mesoporous metal oxides support. We have also designed and screened multiple active metals on the dendritic mesoporous metal oxide catalysts, modified active metal dispersion, and further reduced metal oxides to utilize silica-based catalysts, among other things. Comprehensive characterization of the final products was performed using N2 adsorption and desorption, XRD, HR-TEM, SEM, ICP-OES, XPS, H2-TPD, CO2-TPD, Raman spectroscopy, pulse-chemosorption and DRIFT, in order to determine the chemical and physical properties of the catalysts. The catalysts were found to have the following characteristics. We obtained a CO2 conversion of 25.5 % and a MeOH yield of 6.4 % after at least three cycles of usage in an avantium fixed bed reactor system with a PdCu/CZ-3 catalyst. Additionally, continuous methanol production with a higher yield (6.9 %) has been achieved using our PdZn/CZ-3 catalysts, and the best ultra-dispersed Pd nanoparticles over CZZ catalyst produces more than 12 % methanol yield with constant selectivity to methanol even after a lengthy catalytic test (more than 100 h), demonstrating their industrial viability. Additionally, our PdZn/CeTi-DMSN exhibits a high methanol production of up to 10% and better long-term stability with lower metal oxides content. The adsorption and activation of CO2 to react with the spilled over hydrogen to generate methanol has been researched for the CO2 hydrogenation and utilization reaction. Catalysts' redox, acidic, and basic characteristics all play a crucial part in this reaction and in the formation of the various products. With 2.0 percent Pd, the supported dendritic CeZrZn catalyst exhibits the highest catalytic performance (29.1% conversion and 40.6% MeOH selectivity). Comprehensive analysis revealed in this research not only identified effective catalysts with high activity for a variety of applications, but also established a link between catalytic performance and the material's nature. These discoveries may also aid the researcher in the near future in resolving global environmental problems.

Resistive random access memory (RRAM), based on a two-terminal resistive switching device with a switching element sandwiched between two electrodes, has been an attractive candidate to replace flash memory owing to its simple structure, excellent scaling potential, low power consumption, high switching speed, and good retention and endurance properties. However, due to the current limited understanding of the device mechanism, RRAMs research are still facing several issues and challenges including instability of operation parameters, the relatively high reset current, the limited retention and the unsatisfactory endurance. In this study, we investigated the switching mechanisms, conditions and applications of oxygen vacancy (Vo) filament formation in resistive memories. By studying the behavior of conductive Vo nanofilaments in several metal/oxide/metal resistive devices of various thicknesses of oxides, a resulting model supported by the data postulates that there are two distinct modes of creating oxygen vacancies: i) a conventional bulk mode creation, and ii) surface mode of creating oxygen vacancies at the active metal-dielectric interface. A further investigation of conduction mechanism for the Vo CF only based memories is conducted through insertion of a thin layer of titanium into a Pt/ Ta2O5/Pt structure to form a Pt/Ti/ Ta2O5/Pt device. A space charge limited (SCL) conduction model is used to explain the experimental data regarding SET process at low voltage ranges. The evidence for existence of composite copper/oxygen vacancy nanofilaments is presented. The innovative use of hybrid Vo/Cu nanofilament will potentially overcome high forming voltage and gas accumulation issues. A resistive floating electrode device (RFED) is designed to allow the generation of current/voltage pulses that can be controlled by three independent technology parameters. Our recent research has demonstrated that in a Cu/TaOx/Pt resistive device multiple Cu conductive nanofilaments can be formed and ruptured successively. Near the end of the study, quantized and partial quantized conductance is observed at room temperature in metal-insulator-metal structures with graphene submicron-sized nanoplatelets embedded in a 3-hexylthiophene (P3HT) polymer layer. As an organic memory, the device exhibits reliable memory operation with an ON/OFF ratio of more than 10. / Ph. D.

付記する学位プログラム名: 京都大学卓越大学院プログラム「先端光・電子デバイス創成学」 / 京都大学 / 新制・課程博士 / 博士(工学) / 甲第24622号 / 工博第5128号 / 新制||工||1980(附属図書館) / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 木本 恒暢, 教授 白石 誠司, 准教授 小林 圭 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Excessive CO2 emissions can negatively impact society and our planet. Reduction of CO2 is one potential avenue for its abatement. One of the most significant challenges to reducing CO2 is its extremely stable linear form. Experimentally, Cu/TiO2 has shown promise for CO2 photocatalytic reduction. Dispersed atomic catalysts can achieve high catalytic efficiency on a per atom basis. Active sites also typically having lower coordination number, and therefore may be more reactive. Using density functional theory and experimental techniques, we have investigated the role of surface oxygen vacancies (Ov) and photoexcited electrons on supported single atom catalysts and CO2 reduction. Cu atoms with Ov have shown to aid in the process of bent, anionic CO2 formation. In the first step involving CO2 dissociation (CO2* --> CO* + O*), a single Cu atom in Ov lowered the activation barrier to 0.10 - 0.19 eV, which could enable fast reduction of CO2 even at room temperature, in agreement with experimental findings. A photoexcited electron model was shown to readily promote Cu binding to the surface vacancy, and CO2 adsorption and direct dissociation. Finally, we briefly compare our results to calculations of supported single Pt atoms to determine how metals besides Cu may behave as photocatalysts for CO2 reduction, and we found a single Pt with Ov can promote CO2 dissociation. Our results show that tailoring TiO2 surfaces with defects in conjunction with atomic catalysts may lead to useful catalysts in the photoreduction of CO2.

Oxidkeramische Materialien sind zunehmend von praktischem Interesse für neue Technologien, die in Brennstoffzellen, Sensoren und Ionentransport-Membranen Anwendung finden. Einige dieser Oxide mit Perowskitstruktur ABO3 zeigen hohe Ionen- und Elektronenleitung, ausreichende chemische Stabilität sowie thermisch-mechanische Eigenschaften, wie sie für die Anwendung als Sauerstofftransportmembran benötigt werden. Oxidionentransport erfolgt über einen Oxidionen-Leerstellenmechanismus. Die charakteristische Schwierigkeit für die Anwendung solcher Materialien besteht aber darin, dass die gestellten Forderungen wie hoher Ionentransport und hohe Stabilität sich diametral gegenüberstehen. In dieser Arbeit wurde eine systematische Untersuchung der Beziehungen zwischen Zusammensetzung, Struktur und Stöchiometrie der ferritischer und cobaltitischer Mischoxide und den Transporteigenschaften sowie der thermischen Ausdehnung durchgeführt. Erstmalig wurden thermodynamische und kinetische Parameter von Reihen von Oxiden in einem weiten Bereich von Temperatur und Sauerstoffpartialdruck systematisch bestimmt. Aus den Ergebnissen konnten Empfehlungen gegeben werden für die Zusammensetzung von Perowskitoxiden, die zum Aufbau von Sauerstofftransportmembranen unter bestimmten pO2/T-Bedingungen geeignet sind.

Oxidkeramische Materialien sind zunehmend von praktischem Interesse für neue Technologien, die in Brennstoffzellen, Sensoren und Ionentransport-Membranen Anwendung finden. Einige dieser Oxide mit Perowskitstruktur ABO3 zeigen hohe Ionen- und Elektronenleitung, ausreichende chemische Stabilität sowie thermisch-mechanische Eigenschaften, wie sie für die Anwendung als Sauerstofftransportmembran benötigt werden. Oxidionentransport erfolgt über einen Oxidionen-Leerstellenmechanismus. Die charakteristische Schwierigkeit für die Anwendung solcher Materialien besteht aber darin, dass die gestellten Forderungen wie hoher Ionentransport und hohe Stabilität sich diametral gegenüberstehen. In dieser Arbeit wurde eine systematische Untersuchung der Beziehungen zwischen Zusammensetzung, Struktur und Stöchiometrie der ferritischer und cobaltitischer Mischoxide und den Transporteigenschaften sowie der thermischen Ausdehnung durchgeführt. Erstmalig wurden thermodynamische und kinetische Parameter von Reihen von Oxiden in einem weiten Bereich von Temperatur und Sauerstoffpartialdruck systematisch bestimmt. Aus den Ergebnissen konnten Empfehlungen gegeben werden für die Zusammensetzung von Perowskitoxiden, die zum Aufbau von Sauerstofftransportmembranen unter bestimmten pO2/T-Bedingungen geeignet sind.