This research work focuses on the reactive power compensation of the permanent magnet synchronous generator (PSG) in wind power plants. PSG feeds a fixed voltage dc grid through a rectifier bridge. In variable speed operation, the PSG will be able to build torque only in small speed range. This is due to the fixed magnet of the PSG. External reactive power compensation provides an attractive solution to overcome this problem. Different reactive power compensation configurations were examined. Statics synchronous series compensation and a shunt passive filter were chosen as a compensation method. Simulation and implementation of small wind power plant were performed. The wind power plant consists of the synchronous generator, inverter, rectifier, coupling transformers and shunt passive filter. The experimental results agree to the proposed theory and simulation results. / Der Schwerpunkt meiner Promotion ist die Blindleistungskompensation bei einem permanenterregten Synchrongenerator. Der Synchrongenerator speist das Gleichsspannungsnetz über ein Gleichrichter. In der Drehzahlvariablen Betriebsverhalten können Nachteile auftreten. Die Folge ist, dass bei konstanter Gleichspannung und fester Erregung durch die Permanenterregung nur ein sehr kleiner Drehzahlbereich mit vernünftiger Drehmomentausbeute bedienbar ist. Ein möglicher Ausweg wäre eine variable Kompensationsspannung. Verschiedene Kompensationsverfahren wurden untersucht. Ein Series Active Filter und ein Shunt Passive-Filter wurden als Blindleistungskompensation gewählt. Im Rahmen meiner Dissertation beschäftige ich mich mit dem Aufbau und der Simulation einer Windkraftanlage. Diese besteht aus einem permanenterregten Synchrongenerator, einem Wechselrichrter, einem Gleichrichter, drei Transformatoren und einem passiven Filter. Das Versuchsergebnis zeigt, dass die Theorie mit der Simulation übereinstimmt.

Permanent magnets synchronous reluctance (PMSynRel) motors are attractive due to their high torque density and because a lower quantity of permanent magnets is necessary in comparison with other permanent magnet machines. This thesis deals with the analysis of PMSynRel machines using a finite element method (FEM) and reluctance networks. First, a PMSynRel machine model is built in order to carry out simulations using a finite element method package. The effect of different design parameters such as the combination of the number of poles and slots, the number of flux barriers or the number of magnets can be studied since the implementation provides the possibility to change those variables. Next, a reluctance networks model, aimed to enable lower computation times than corresponding finite element models, is implemented for analysing the flux density distributions along the air gap of the machine disregarding the magnetic influence of the rotor. Finally, the results are compared with FEM simulations. It is concluded that the agreement reached is satisfactory in most of the cases analysed.

This thesis deals with the design of a permanent-magnet synchronous inner rotor motor for an in-wheel application for the Shell Eco Marathon Urban concept vehicle. First of all, concepts related to permanent magnet motors are studied. Likewise, different features of permanent magnet motors are qualitatively evaluated in order to choose the most suitable. A radial flux motor is selected based on its solid, economic and acceptable characteristics. Next, a detailed study of concentrated windings is carried out. Through this investigation, undesirable configurations of pole and slot numbers due to unbalanced magnetic pull or a low fundamental winding factor will be avoided and how to determine the different winding layouts for different pole and slots configuration will be explained. As well, based on this study, and the magnetic and electric behavior of the machine, an analytical model is created. This model calculates the optimum size and characteristics of a machine in order to obtain lightweight design. After that, the design of a program based on a finite element method that simulates different situations for the machine is accomplished, dealing with the difficulties that entails the concentrated windings. Finally, through the use of this program, the machine calculated by the analytical model is analyzed, specially regarding that it does not surpass some important margin in order not to be demagnetized or not to surpass the maximum phase voltage supplied by the batteries.

The thesis presents deals with the design, analysis, test and control of permanent magnetsynchronous motor(PMSM). An analytical model was carried out based on the d-q frame and the equivalent circuit of PMSM, theanalytical model gives an approximation value of the machine parameters and is carried out byequations from the listed references. this phase includes many iteration steps, once the results wereobtained they were compared with the motor specifications and if they don’t match the requiredspecifications the process must be done again until the desired design is obtained. Once the analytical model is obtained a Finite Element Simulation was carried out using FEMMsoftware to validate the design, in this phase the designed machine in the analytical model isanalyzed and validated, once the simulation is done the results from both models are compared anddiscussed in the results chapter. It’s important to mark that during the design phase some design parameters were affected andlimited by some factors, for example, the air gap length has been magnified due to manufacturinglimits. The manufacturing process and the prototype building have been started once the optimal designwas selected, the manufacturing process was explained and a comparison study was made to selectthe best manufacturing process suitable and available for this thesis.

This thesis is a study on an unconventional slow speed direct drive permanent magnet (PM) generator. Unlike a standard permanent magnet synchronous generator (PMSG) which has the copper coils wound around iron teeth, the work in this thesis will present a generator where the copper coils are directly mounted on the stator which eliminates the slots and teeth in the generator. By having a slotless design it is possible to eliminate cogging torque, iron losses in teeth and achieve a lightweight design. These characteristics can prove useful when developing generators for an application such as wind turbines, or more specifically vertical axis wind turbines (VAWTs) in remote areas where weight and serviceability is of concern. This thesis consists of two main parts where the main focus was on the design and simulation of slotless generators. The second part of the thesis was to investigate an available slotless axial flux machine. For the simulations, three different models were created in 2D using CAD software. Two of the models were double-rotor slotless generators and one was a single rotor variant. The electromagnetic properties of these models were analysed using FEMM and COMSOL. The results showed that the double rotor variant with the smaller magnets were more favourable considering the price of magnets and no iron core losses. The experimental results of the axial flux machine gave insight into the construction of commercially available axial slotless generators which could be used to further analyse these types of machines.

Bei eigengekühlten Elektromaschinen in Außenläuferbauweise resultiert aus der schwierigeren Abführung der Statorverluste üblicherweise eine Reduktion der elektromagnetischen Ausnutzung. Im Beitrag wird am Beispiel eines permanentmagnetisch erregten Synchrongenerators für eine Kleinwindenergieanlage das Verfahren der intensivierten Statorrohrinnenkühlung unter Nutzung der Windströmung durch einen im Statorrohr angeordneten Kühlkörper diskutiert. Neben der elektromagnetischen und strömungsmechanischen bzw. thermischen Modellierung wird die experimentelle Trennung der Einzelverluste vorgestellt. Es wird gezeigt, dass die Ausnutzung der Maschine durch die intensivierten Statorrohrinnenkühlung um ca. 40 % gesteigert werden kann. / For self-ventilated electrical machines in outer rotor design, the difficult dissipation of stator losses usually results in a reduction of the electromagnetic utilization. Based on an example of a permanent magnet synchronous generator for a small wind turbine, the method of intensified inner stator tube cooling using the wind flow through a heat sink arranged in the stator tube is discussed in the article. In addition to the electromagnetic and fluid mechanical as well as thermal modeling, the experimental separation of the losses is presented. It is shown that the utilization of the machine can be increased by approx. 40 % by means of the intensified internal cooling of the stator tube.

When developing three phase motor drives, the best way to validate the desiredfunctionality is to connect the inverter to an actual electrical motor. However, when developingfunctions which are not directly involved in controlling the motor, it could bemore efficient to use a real-time software model of the motor. In this master thesis, the developmentand implementation of a software model of a permanent magnet synchronousmotor (PMSM) is presented. This model was based on general dynamic equations forPMSM in a rotating reference frame (dq-frame). The model was simulated and convertedto C code using model based software development in Mathworks Simulink. To providemore realistic performance of the model, a finite element analysis (FEA) was done of anactual PMSM using the software tool FEMM. This analysis resulted in data describingthe relation between flux linkage and current which, when added into to software model,limits the produced torque due to magnetic saturation. Both the FEMM model and thefinal software model was compared to a corresponding actual motor for validation andperformance testing. All this resulted in a fully functional software model which was executableon the inverter. In the comparison of FEMM model to the real motor, a deviationin produced torque was discovered. This led to the conclusion that the model needed to beimproved to perform more alike the real motor. However, for this application the modelwas considered good enough to be used in future software development projects. / N¨ar kontrollsystem till trefasmotorer utvecklas s°a ¨ar det mest vanliga och troligendet b¨asta s¨attet f¨or funktionsvalidering att k¨ora drivenheten kopplad mot en riktig elektriskmotor. D¨aremot, om funktioner som ej ¨ar direkt kopplade till sj¨alva drivningen av motornutvecklas, s°a kan det vara mer effektivt att ist¨allet anv¨anda en mjukvarumodell. I det h¨arexamensarbetet s°a presenteras en mjukvarumodell av en permanentmagnetiserad synkronmotor(PMSM). Modellen baserades p°a de generella ekvationerna f¨or PMSM och simuleradessamt kodgenererades i Mathworks verktyg Simulink. F¨or att g¨ora modellen mer realistisks°a kompletterades den med data som beskriver relationen mellan det l¨ankade fl¨odetoch str¨om f¨or att ¨aven ta h¨ansyn till magnetisk m¨attnad. Den informationen simuleradesfram i verktyget FEMMgenom fl¨odesber¨akningar p°a en specifik motor typ. Samma motortyp har ocks°a j¨amf¨orts med den slutgiltiga mjukvarumodellen med avseende p°a utvecklatvridmoment vilket resulterade i n°agot st¨orre skillnader ¨an f¨orv¨antat. Slutsatsen blevs°aledes att modellen beh¨over f¨orb¨attras f¨or att p°a ett b¨attre s¨att st¨amma ¨overens med verklighetenmen att den fungerar tillr¨ackligt bra f¨or den ¨amnade applikationen.

In this thesis, the basics of electromagnetic theory for wave-energy conversion are reviewed, some of the characteristics of the ocean wave are investigated, some of the power take-off (PTO) systems are introduced, and details about linear permanent magnetic machines, in particular, are discussed.  The thesis aims to model the novel linear transverse flux machine designed by Anders Hagnestål and to build hysteresis current controller for power factor correc- tion. Although this machine is expected to have high performance in terms of efficiency, it also exhibits a strong mutual interaction between the three phases of the machine. Thus, simplification of the actual model of the machine is im- posed to mitigate the complexity of the machine and facilitate the Simulink model. Four cases of the double band hysteresis control are studied. The cur- rents seem to be responding properly to the control scheme; however, software and hardware programming of a microprocessor would be preferable to ensurethe applicability of the control strategy in a real environment. / I detta examensarbete undersöks elektromagnetisk teori och havsvågors egenskaper. Några energiomvandlingssystem introduceras och permanentmagnetiserade maskiner diskuteras i detalj. Syftet med avhandlingen är att modelleraen ny linjär transversalflödesmaskin som är designad av Anders Hagnestål och att bygga en hysteresbaserad strömkontroll för denna. Även om maskinen förväntas prestera bra, uppvisar den också en stark ömsesidig magnetisk interaktion mellan de tre faserna. För att kunna hantera detta problem och därmed kunna genomföra simuleringar införs en förenklad elektromagnetisk modell av maskinen. En strömkontroller har implementerats i Simulink, där fyra fall av dubbelbandshystereskontroll studerats. Resultaten från simuleringarna visar att strömkontrollern fungerar. Nästa steg i projektet är att utföra mjukvaru och hårdvaruprogrammering av en mikrokontroller för att testa systemet i enverklig miljö.

This thesis focuses on modelling of the permanent magnet synchronous reluctancemotor (PMSynRM), which has drawn considerable attention by researchers thanks toits high efficiency and wide range of speed operation. Comparisons with measurementsfrom a four-pole PMSynRM with four barriers and 24 stator slots have been carriedout. In this thesis work, Matlab and Comsol Multiphysics are used to implement theparameterized PMSynRM model.Models of the PMSynRM in two-dimensions (2D) and three-dimensions (3D) havebeen implemented. The electromotive force (back emf) at no load condition for a fullpitchand short-pitch winding as well as the air-gap flux density distribution have beencalculated. A parametric study has been performed where the air-gap length, insulationratio of both d and q-axes, as well as flux barrier number have been varied and theeffect on the machine performance has been observed. The losses including eddycurrentlosses in permanent magnet, stator lamination loss, and rotor lamination losshave been calculated. The back emf and rated torque as well as developed torque witha pure q-axis current have been compared with corresponding experimental data.A 3D model of an axially shortened rotor has also been implemented in where apulsating current has been applied to estimate eddy-current losses in the permanentmagnets. The predicted losses from the 2D model and 3D model have been comparedfor pulsating currents with varying frequency and magnitude. / Denna avhandling fokuserar på modellering av permanentmagneten synkronreluktansmotor (PMSynRM), som har fäst stor uppmärksamhet av forskare tack varedess höga effektivitet och brett spektrum av hastigheter. Jämförelser med mätningarfrån en fyrpolig PMSynRM med fyra hinder och 24 statorspåren har utförts. I dettaexamensarbete, Matlab och Comsol Multi används för att implementera parameterPMSynRM modell. Modeller av PMSynRM i två dimensioner (2D) och tre dimensioner(3D) har genomförts. Den elektromotoriska kraften (mot-emk) utanbelastningstillstånd för en full-pitch och kort stigning lind samt luftgapetfördelningsflödestäthet har beräknats. En parametrisk studie har gjorts där luftspaltlängden,isolering förhållande av både d- och q-axlar, såväl somflödesbarriärnummer har varierats och effekten på maskinens prestanda harobserverats. Förlusterna inklusive virvelströmsförluster i permanentmagnet,statorskiktet förlust, och rotorlamine förlust har beräknats. Mot-emk och nominelltvridmoment samt utvecklat vridmoment med en ren q-axelström har jämförts medmotsvarande experimentella data. En 3D-modell av en axiellt förkortad rötor har ocksågenomförts i där en pulserande ström har tillämpats för att uppskattavirvelströmsförluster i permanentmagneterna. De förutsagda förluster från 2Dmodellenoch 3D-modell har jämförts för pulserande strömmar med varierandefrekvens och storlek.

No description available.