No description available.

This study has been done in order to examine which type of pile, pile driving- and waterproofing methodsare most suited for an existing building. A building that will undergo an extensive reinforcement of itsfoundation.The study has been made in regard to the following conditions:● Different types of clay soil (Cohesion soil)● Underlying rock structure with heavy incline (8° slope)● Sensitive environment for vibrations and ground displacements● Limited accessibility (Room and maximum weight)● Compressive and tensile forces● Pool (Water environment)To answer the questions of statement a scientific literature study, interview with a foundation expert,calculations in sizing, but also time and cost analysis has been conducted. A site visit to an object ofreference, Nya Krav Himmerfjärdsverket, occurred where a reconstruction of an existing building withextensive work of reinforcement to its’ foundation was in progress.The steel pipe pile with anchor and steel core pile are the best pile types in such conditions as compressiveand tensile forces, clay soil with underlying inclined rock bed, limited accessibility and sensitivesurrounding environment. Which pile type, pile driving- and waterproofing methods that are most suited forsuch conditions is different for each project. The steel core pile is more suitable for higher loads, rockstructures in incline and when verification of load capacity is not needed. At the same time the steel pipepile is more suited when the underlying rock bed is far below ground level, where you would need manypile elements and joints. In addition, the steel pipe pile is suitable for buildings with a complex loaddistribution, where a greater number of piles with lower load capacities is needed in order to satisfy this.The best pile driving method for drilling in sensitive environment is the water equipped down-the-hole(DTH) drill. This drilling method is gentle to surrounding piles in existing building.In order to minimise the risk of water penetration and then expand the life span of the construction, use ofa combination of different waterproofing systems is to prefer when waterproofing pile heads or pilefoundations.

Yes / In this study, a new three-dimensional (3-D) model was developed to provide better understanding of the mechanism for wave-induced seabed response around mono-pile. Based on poro-elastic theory, the fully dynamic (FD) formulations were adopted in the present model to simulate pore water pressure, soil stresses, displacements of both soil and mono-pile. Good agreement between numerical simulation and experimental results was obtained. Based on parametric study, numerical results indicated: (1) wave diffraction and reflection have significant effects on pore water pressure and soil displacements around mono-pile; (2) the most sensitive position for seabed parameter to pore water pressure around mono-pile locates in front of mono-pile while the least sensitive position is at the position of angle 3π/4 with respect to the incident wave direction; and (3) the increase of mono-pile horizontal displacement corresponds to the increase of wave height and the decrease of seabed Young's modulus. / National Science Fund for Distinguished Young Scholars (51425901), the National Natural Science Foundation of China (51209082, 51379071, 41176073), the Specialized Research Fund for the Doctoral Program of Higher Education of China (20120094120006, 20130094110014), the 111 project (B12032), the 333 project of Jiangsu Province (2013Ⅲ-1882)

There is ussualy used the Masopust's method to assessment the piles in Czech Republic. This method is based on statistical processing of large data set of load piles tests. Due to the using of regression coefficients this method is relatively complicated and not very transparent. Instead, foreign standards ussualy use direct the values of limit stress on the base of piles and unit friction capacity. Procedure for determining the bearing capacity of the piles is thus considerably simplified. In this thesis the Masopust's method is compared with the methods used in Germany and Austria. This comparison provides insight to the safety level that include various approaches.

In an effort to obtain 100-year level hurricane protection for southeastern Louisiana, the U.S. Army Corps of Engineers (USACE) has implemented design guidelines that both levees and structures shall be designed to. Historically, USACE has used concrete piles or steel H-piles as the foundations for these structures. Because of the magnitude of obtaining 100-year level hurricane protection, limited resources, and a condensed timeline, spiral welded pipe piles can be manufactured as an alternative to either the concrete piles or steel H-piles. This research will provide the necessary background for understanding pile foundations, will compare the behaviors of spiral welded pipe piles to that of other piles with respect to geotechnical concerns through a series of pile load tests, and will offer a current cost analysis. This background, testing, and cost analysis will show that spiral welded pipe piles are a viable alternative for USACE structures from a geotechnical and economic perspective.

Esta dissertação apresenta uma avaliação do comportamento de estacas hélice contínua quanto à capacidade de carga, ao recalque e à segurança e confiabilidade, a partir de um cenário de análise em que foi considerado um banco de dados de 58 provas de carga estáticas, realizadas em estacas hélice contínua de 13 obras distintas. Esta pesquisa está focada principalmente no comportamento carga-recalque e confiabilidade de fundações em estacas hélice contínua. Nesta análise foi também verificada a aplicabilidade do método proposto por Aoki (1989) para determinação da curva carga-recalque destas provas de carga. Os valores de capacidade de carga medidos foram comparados com os previstos pelos método Aoki & Velloso (1975), o método Decourt & Quaresma (1978), o método de Cabral (1996), e o método Alonso (1996). Estes métodos também foram utilizados para previsão de transferência de carga nas estacas, necessária para a previsão da curva carga-recalque pelos método de Aoki (1989). Adicionalmente, com os resultados das provas de carga foram estimadas para cada obra a probabilidade de ruína da fundação, e de ocorrência de recalques superiores a um valor limite. / This dissertation presents an evaluation of the behavior of continuous flight auger piles on ultimate capacity, settlments, safety and reliability, from a scenario analysis in which we considered a database of 58 static load tests, performed on piles of 13 distinct sites. However, this research is focused on the loaddisplacement behavior and reliability of this type of foundation. This analysis also verified the applicability of the method proposed by Aoki (1989) to determine the load-displacement curve of these pile load tests. The values of measured pile capacity were compared with those provided by the method Aoki & Velloso (1975), the method Decourt & Quaresma (1978), the method Cabral (1996), and the method Alonso (1996). These methods were also used to predict the load transfer along the piles, necessary to predict the load-displacement curve by the method of Aoki (1989). Additionally, the results of these load tests were used to estimate the probability of failure of the foundations tested, and the occurrence of settlements exceeding a threshold value.

A utilização de estacas helicoidais como fundação de linhas de transmissão de energia elétrica tem aumentando significativamente no Brasil. No entanto, em alguns casos de obra, a camada de solo adequada para se instalarem as hélices da estaca encontra-se em profundidade economicamente inviável para o uso deste tipo de fundação. Esta foi a razão que motivou a presente pesquisa, que tem como objetivo avaliar soluções para a instalação de estacas helicoidais mais curtas, ancoradas em solo de capacidade inferior à necessária para atender às cargas de projeto. Nesta dissertação, foram avaliadas duas soluções alternativas para o aumento de capacidade de carga de fundações por estacas helicoidais, para os casos de carregamento de tração e compressão. A primeira alternativa verificada foi a injeção de calda de cimento em torno das hélices da ponta da estaca. A segunda solução testada foi o preenchimento com argamassa em torno da haste da estaca acima das hélices. Foram realizadas na presente pesquisa nove provas de carga (cinco de tração e quatro de compressão): três em estacas helicoidais convencionais, quatro em estacas helicoidais com injeção de calda de cimento e duas em estacas helicoidais com fuste de argamassa. Após a realização de provas de carga nas estacas, estas foram exumadas para se verificar a forma da coluna de argamassa e as formas de bulbos resultantes das injeções realizadas com calda de cimento. A partir dos resultados dos ensaios, foi verificado que a capacidade de carga da estaca á tração pode ser aumentada usando-se as alternativas testadas. Porém, são necessários mais ensaios para avaliar a eficiência destes procedimentos em diferentes condições de solo e configuração de estacas. / The use of helical piles as foundation for transmission lines has increased significantly in Brazil. However, in some sites, the soil layer suitable for installing the pile helices are considerably deep and it is economically unviable to use this type of foundation. This reason motivated the current study, which aims to evaluate solutions for the installation of helical piles anchored in soil with low capacity. In this research, it was evaluated two alternative solutions to improve the helical pile capacity. The first alternative is injecting a water/ cement mixture which is delivered to the ground throught holes, placed between the upper and bottom helices. The second alternative solution is helical piles with a mortar shaft. Nine pile load tests were performed for the present investigation (five in tension and four in compression): three on conventional helical piles, four on helical piles with injection, and two on helical piles with mortar shaft. After that, the helical piles were exhumed for the verification of the shaft shape and the forms of the bulbs resulting from injections performed with cement mixture. The results of these tests indicated that the uplift capacity of helical piles can be increased by using the alternatives tested. However, more tests are needed to evaluate the effectiveness of these procedures, in different soil conditions and pile configurations.

The lateral resistance of pile foundations is typically based on the performance of round piles even though other pile types are used. Due to lack of data there is a certain level of uncertainty when designing pile foundations other than round piles for lateral loading. Theoretical analyses have suggested that square sections will have more lateral resistance due to the increased side shear resistance, no test results have been available to substantiate the contention. Full-scale lateral load tests involving pile shapes such as circular, circular wrapped with high density polyethylene sheeting, square, H, and circular with a corrugated metal sleeve have been performed considering the influence of soil-pile interaction on lateral load resistance. The load test results, which can be summarized as a p-y curve, show higher soil resistance from the H and square sections after accounting for differences in the moment of inertia for the different pile sections. The increased soil resistance can generally be accounted for using a p-multiplier approach with a value of approximately 1.25 for square or 1.2 for H piles relative to circular piles. It has been determined that high density polyethylene sheeting provides little if any reduction in the lateral resistance when wrapped around a circular pile. Circular piles with a corrugated metal sleeve respond to lateral loading with higher values of lateral resistance than independent circular piles in the same soil.

A utilização de estacas helicoidais como fundação de linhas de transmissão de energia elétrica tem aumentando significativamente no Brasil. No entanto, em alguns casos de obra, a camada de solo adequada para se instalarem as hélices da estaca encontra-se em profundidade economicamente inviável para o uso deste tipo de fundação. Esta foi a razão que motivou a presente pesquisa, que tem como objetivo avaliar soluções para a instalação de estacas helicoidais mais curtas, ancoradas em solo de capacidade inferior à necessária para atender às cargas de projeto. Nesta dissertação, foram avaliadas duas soluções alternativas para o aumento de capacidade de carga de fundações por estacas helicoidais, para os casos de carregamento de tração e compressão. A primeira alternativa verificada foi a injeção de calda de cimento em torno das hélices da ponta da estaca. A segunda solução testada foi o preenchimento com argamassa em torno da haste da estaca acima das hélices. Foram realizadas na presente pesquisa nove provas de carga (cinco de tração e quatro de compressão): três em estacas helicoidais convencionais, quatro em estacas helicoidais com injeção de calda de cimento e duas em estacas helicoidais com fuste de argamassa. Após a realização de provas de carga nas estacas, estas foram exumadas para se verificar a forma da coluna de argamassa e as formas de bulbos resultantes das injeções realizadas com calda de cimento. A partir dos resultados dos ensaios, foi verificado que a capacidade de carga da estaca á tração pode ser aumentada usando-se as alternativas testadas. Porém, são necessários mais ensaios para avaliar a eficiência destes procedimentos em diferentes condições de solo e configuração de estacas. / The use of helical piles as foundation for transmission lines has increased significantly in Brazil. However, in some sites, the soil layer suitable for installing the pile helices are considerably deep and it is economically unviable to use this type of foundation. This reason motivated the current study, which aims to evaluate solutions for the installation of helical piles anchored in soil with low capacity. In this research, it was evaluated two alternative solutions to improve the helical pile capacity. The first alternative is injecting a water/ cement mixture which is delivered to the ground throught holes, placed between the upper and bottom helices. The second alternative solution is helical piles with a mortar shaft. Nine pile load tests were performed for the present investigation (five in tension and four in compression): three on conventional helical piles, four on helical piles with injection, and two on helical piles with mortar shaft. After that, the helical piles were exhumed for the verification of the shaft shape and the forms of the bulbs resulting from injections performed with cement mixture. The results of these tests indicated that the uplift capacity of helical piles can be increased by using the alternatives tested. However, more tests are needed to evaluate the effectiveness of these procedures, in different soil conditions and pile configurations.

Esta dissertação apresenta uma avaliação do comportamento de estacas hélice contínua quanto à capacidade de carga, ao recalque e à segurança e confiabilidade, a partir de um cenário de análise em que foi considerado um banco de dados de 58 provas de carga estáticas, realizadas em estacas hélice contínua de 13 obras distintas. Esta pesquisa está focada principalmente no comportamento carga-recalque e confiabilidade de fundações em estacas hélice contínua. Nesta análise foi também verificada a aplicabilidade do método proposto por Aoki (1989) para determinação da curva carga-recalque destas provas de carga. Os valores de capacidade de carga medidos foram comparados com os previstos pelos método Aoki & Velloso (1975), o método Decourt & Quaresma (1978), o método de Cabral (1996), e o método Alonso (1996). Estes métodos também foram utilizados para previsão de transferência de carga nas estacas, necessária para a previsão da curva carga-recalque pelos método de Aoki (1989). Adicionalmente, com os resultados das provas de carga foram estimadas para cada obra a probabilidade de ruína da fundação, e de ocorrência de recalques superiores a um valor limite. / This dissertation presents an evaluation of the behavior of continuous flight auger piles on ultimate capacity, settlments, safety and reliability, from a scenario analysis in which we considered a database of 58 static load tests, performed on piles of 13 distinct sites. However, this research is focused on the loaddisplacement behavior and reliability of this type of foundation. This analysis also verified the applicability of the method proposed by Aoki (1989) to determine the load-displacement curve of these pile load tests. The values of measured pile capacity were compared with those provided by the method Aoki & Velloso (1975), the method Decourt & Quaresma (1978), the method Cabral (1996), and the method Alonso (1996). These methods were also used to predict the load transfer along the piles, necessary to predict the load-displacement curve by the method of Aoki (1989). Additionally, the results of these load tests were used to estimate the probability of failure of the foundations tested, and the occurrence of settlements exceeding a threshold value.