No description available.

The proton exchange membrane fuel cells should have three major advantages: 1. micro-phase separation, 2. mechanical properties and 3. thermal stability. According to the recent literature and the material of core benzene ring poly (arylene ether)s studied by our group, this paper synthesize a series of the locally and densely sulfonated polymer. We use core benzene ring as the diol monomer and the containing CF3 groups as the fluorine monomer to synthesis poly (arylene ether)s via nucleophilic displacement reactions, and then use the different concentrations synthesized sulfonated polymer by sulfonic acid reaction. According to NMR¡¦s result we confirmed that the structure of synthetic materials is correct. By using GPC we get that the KP1, KP2, and KP3¡¦s molecular weight about 20000 (g/mol) ; The thermal stability up to 530OC for 5% loss in TGA under nithtrogen, to prove thisseries of polymer excellent thermal stability. After sulfonation, SKP1, SKP2 and SKP3¡¦s decomposition temperature decreased about 200OC ~ 250OC ranging with increasing degree of sulfonation. By DSC analysis, K1, K2 and K3 monomer's Tg followed up with the increase of the benzene ring number, however, the polymer does not have any apparent peak. About the Proton conductive, SKP2C IEC 2.23mequiv / g, water uptake 94%, the highest proton conductivity can be as high as 68.2 mS / cm, has been similar to Nafion 117 of 70 mS / cm.

Proton Exchange Membrane Fuel Cell has the potential to become an important energy conversion technigne. Lots of efforts oriented toward the electrochemical conversion of energy using proton exchange membrane (PEM) fuel cells have been enormously accelerated with the hope to promote as an alternative power source for transport and portable purposes. However, they still suffer from such disadvantages as limited operation temperature, high cost, insufficient durability and high methanol permeability.Good membranes should meet several strict requirements as follows; reasonable proton conductivity, high stability and durny the performance of a fuel cell environment,outstanding mechanical toughness, high heat endurance, and impermeability to fuel gas or liquid. Presently,a lot of references have mentioned some sulfonatied polymer sulfonated of poly(ether ether ketone) (SPEEK), sulfonatedpolysulfone (SPSF), sulfonated polysulfide sulfone(SPSS), and polybenzimidazole(PBI) and so on.To achieve high proton conductivity usually match with a high degree of sulfonation that means owning a large Ion Exchange Capacity, IEC.But which in turn leads to a decrease in the electrochemical¡Bdimensional stability¡Bwater uptake¡Boxidative stability. Therefore they suffer from such disadvantages as limited operation range of temperature.Three aromatic poly(arylene ether)s P4b¡BP4c¡BP4d were synthesized from the polymer consists nine of polyaromatic groups with bisfluoride monomer at studying long time in our laboratory with S1¡BS2¡BS3 diol monomer.The molecular weight of the polymer (Mw:1.49¡Ñ105~5.3¡Ñ105 g/mol ,PDI: 1.82~2)This polymer has high strength,thermal stability and all of polymers own very high Td ,which are over than 500oC.We sulfonatied the polymer in order to apply as the proton exchange membrane of a fuel cell.The results showed after sulfonation of P4b¡BP4c¡BP4d.All IEC reaches 3.9~1(meq/g).According to above result, we propose the aromatic poly(arylene ether)s is good matenal can be used on all application as a proton exchange membrane.

This research mainly investigated how the hydrophilic and hydrophobic properties of gas diffusion layer, and the different open ratio of the flowfield may affect the performance of the micro proton exchange membrane fuel cell (£gPEMFC). The flow plate used in this experiment was made through deep UV lithography manufacturing processes and micro-electroforming manufacturing processes. Four different open ratios, 52.8 %, 50.8 %, 75.2 % and 75.75 %, of the flowfield were designed for the flow plate composed of serpentine-parallel and serpentine geometrical micro configurations. Acrylic (PMMA: Polymethylmethacrylate) was used to make the terminal plate placed on both sides of the micro proton exchange membrane fuel cell. By varying values of the hydrophilic and hydrophobic properties of the anode gas diffusion layer, the effects of these two parameters on the polarization curve and power density of the cell were explored. All results obtained in the experiment are presented by P-I curve and V-I curve. The experiment results show that, with 1: 5 flow ratio of anode to cathode, a design with the gas diffusion layer made of the material with hydrophobic factor 20 wt.% and with open ratio of 50.8 % for anode flow channel as well as open ratio of 75.75 % for cathode flow channel may have the best performance.

The characteristics of the proton exchange membrane fuel cell (called PEMFC) stacks made with the graphite unipolar/bipolar plates are studied in this thesis. Using pure hydrogen as fuel, certain experimental work is conducted to help us to understand the factors which influence on the performance of a HFC stack. The experimental work under various operating conditions starts from single cell stacks to multi-cell stacks. The maximum power is about 200 W, which is made with two 10-cell stacks in series. For simplification, all of the flow channels in the cathode are open type in which air is directly supplied from ambient by fan. The comparison of the performance of two single cells, which are made with both a graphite unipolar plate and a new-type carbon fiber unipolar plate, is conducted. The total resistances of the two types of bipolar plates with gas diffusion layers are tested to help us to understand their strong or weak points. The experimental results display that the double inlets has better performance than the single inlet due to larger entrance space. Increasing the applied torque will reduce the contact resistance between bipolar plate and diffusion layer and also the gaps between the fibers of carbon cloth. Reducing the contact resistance is helpful in increasing the performance of the cell, but reducing the gaps between fibers will inhibit the entering of reactive gas and is unfavorable for performance; therefore, the proper torque is necessary to obtain the best voltage output. When air is used as an oxidizer and the flow channel is an open type channel, the fan in high rotating speed is helpful at high current density. The high air volume flow rate can supply sufficient oxidizer and avoid the decay of the voltage output at high current density. At the current density 1 A/cm2, the power density of the single-cell stack is about 400 mW/cm2 and the power density of the 10-cell stack is down to about 310 mW/cm2 in our experiment. The rib of the carbon fiber unipolar/bipolar plate is soft, so there is no deformation in the gas diffusion layer in stack assembly. Only slight compression is needed to assemble a stack; therefore, the reactive gas can easily flow into the most of active area. This type unipolar/bipolar plate is made with low density plastic except that the rib is made with carbon fiber bunches. Thus the new plate is weight light, cost low and volume small. So it is quite possible that the new-type of carbon fiber plate is used as substitution for the graphite bipolar plate in the future. In that case the light, low cost and high performance choice can be achieved.

It is desirable to increase the operation temperature of proton exchange membrane fuel cells above 100oC due to fast electrode kinetics, high tolerance to fuel impurities and simple thermal and water management. In this study / the objective is to develop a high temperature proton exchange membrane fuel cell. Phosphoric acid doped polybenzimidazole membrane was chosen as the electrolyte material. Polybenzimidazole was synthesized with different molecular weights (18700-118500) by changing the synthesis conditions such as reaction time (18-24h) and temperature (185-200oC). The formation of polybenzimidazole was confirmed by FTIR, H-NMR and elemental analysis. The synthesized polymers were used to prepare homogeneous membranes which have good mechanical strength and high thermal stability. Phosphoric acid doped membranes were used to prepare membrane electrode assemblies. Dry hydrogen and oxygen gases were fed to the anode and cathode sides of the cell respectively, at a flow rate of 0.1 slpm for fuel cell tests. It was achieved to operate the single cell up to 160oC. The observed maximum power output was increased considerably from 0.015 W/cm2 to 0.061 W/cm2 at 150oC when the binder of the catalyst was changed from polybenzimidazole to polybenzimidazole and polyvinylidene fluoride mixture. The power outputs of 0.032 W/cm2 and 0.063 W/cm2 were obtained when the fuel cell operating temperatures changed as 125oC and 160oC respectively. The single cell test presents 0.035 W/cm2 and 0.070 W/cm2 with membrane thicknesses of 100 &micro / m and 70 &micro / m respectively. So it can be concluded that thinner membranes give better performances at higher temperatures.

A mathematical model for a proton exchange membrane fuel cell is the focus of this thesis. Modeling and simulations are carried out with an aim to understand the influence of operational and geometrical parameters on the inner reaction and performance of a proton exchange membrane fuel cell, and discuss the distributions of physical phenomena in membrane and catalyst layer. Than, the results of modeling are compared and analyzed with the experiments, and discuss the reasons of influences of the performance of PEMFC. The results show that activation overpotential is the major reason of influence of the performance at low current density (less than ), and diffusion and ohmic overpotential are substantially increased at high current density (great than ). The membrane of higher membrane conductivity and more thin, increasing pressure of cathode gas and use oxygen can enhance the performance of a PEMFC. The performance almost no influence for the catalyst layer over 0.3£gm. The catalyst layer thin and uniform can decrease coating of this layer. The results of modeling and experiments show that experiments have contact resistance between materials, and the performance slightly lower than performance of modeling, and the differences that at high current density great than low current density.

Due to escalating energy costs and limited fossil fuel resources, much attention has been given to polymer electrolyte membrane (PEM) fuel cells. Gas diffusion layers (GDLs) play a vital role in a fuel cell such as (1) water removal, (2) cooling, (3) structural backing, (4) electrical conduction and (5) transporting gases towards the active catalyst sites where the reactions take place. The power density of a PEM fuel cell in part is dependent upon how uniform the gases are distributed to the active sites. To this end, research is being conducted to understand the mechanisms that influence gas distribution across the fuel cell. Emerging PEM fuel cell designs have shown that higher power density can be achieved; however this requires significant changes to existing components, particularly the GDL. For instance, some emerging concepts require higher through-plane gas permeability than in-plane gas permeability (i.e., anisotropic resistance) which is contrary to conventional GDLs (e.g., carbon paper and carbon cloth), to obtain a uniform gas distribution across the active sites. This is the foundation on which this thesis is centered. A numerical study is conducted in order to investigate the effect of the gas permeability profile on the expected current density in the catalyst layer. An experimental study is done to characterize the effects of the weave structure on gas permeability in woven GDLs. Numerical simulations are developed using Fluent version 6.3.26 and COMSOL Multiphysics version 3.5 to create an anisotropic resistance profile in the unconventional GDL, while maintaining similar performance to conventional GDL designs. The effects of (1) changing the permeability profile in the in-plane and through-plane direction, (2) changing the thickness of the unconventional GDL and (3) changing the gas stoichiometry on the current density and pressure drop through the unconventional GDL are investigated. It is found that the permeability profile and thickness of the unconventional GDL have a minimal effect on the average current density and current density distribution. As a tradeoff, an unconventional GDL with a lower permeability will exhibit a higher pressure drop. Once the fuel cell has a sufficient amount of oxygen to sustain reactions, the gas stoichiometry has a minimal effect on increases in performance. Woven GDL samples with varying tightness and weave patterns are made on a hand loom, and their in-plane and through-plane permeability are measured using in-house test equipment. The porosity of the samples is measured using mercury intrusion porosimetry. It is found that the in-plane permeability is higher than the through-plane permeability for all weave patterns tested, except for the twill weave with 8 tows/cm in the warp direction and 4 tows/cm in the weft direction, which exhibited a through-plane permeability which was 20% higher than the in-plane permeability. It is also concluded that the permeability of twill woven fabrics is higher than the permeability of plain woven fabrics, and that the percentage of macropores, ranging in size from 50-400 µm, is a driving force in determining the through-plane permeability of a woven GDL. From these studies, it was found that the graduated permeability profile in the unconventional GDL had a minimal effect on gas flow. However, a graduated permeability may have an impact on liquid water transport. In addition, it was found that graduating the catalyst loading, thereby employing a non-uniform catalyst loading has a greater effect on creating a uniform current density than graduating the permeability profile.

Proton exchange membrane fuel cells (PEMFCs) and direct methanol fuel cells (DMFCs) are two types of low-temperature fuel cells (LTFCs) that operate at temperatures less than 100 °C and are appealing for portable, transportation, and stationary applications. However, commercialization has been hampered by several problems such as cost, efficiency, and durability. New electrocatalysts must be developed that have higher oxygen reduction reaction (ORR) activity, lower precious metal loadings, and improved durability to become commercially viable. This dissertation investigates the development and use of new electrocatalysts for the ORR. Core-shell (shell@core) Pt@Pd[subscript x]Cu[subscript y]/C electrocatalysts, with a range of initial compositions, were synthesized to result in a Pt-rich shell atop a Pd[subscript x]C[subscript y]-rich core. The interaction between core and shell resulted in a delay in the onset of Pt-OH formation, accounting in a 3.5-fold increase in Pt-mass activity compared to Pt/C. The methanol tolerance of the core-shell Pt@PdCu₅/C was found to decrease with increasing Pt-shell coverage due to the negative potential shift in the CO oxidation peak. It was discovered that Cu leached out from the cathode has a detrimental effect on membrane-electrode assembly performance. A spray-assisted impregnation method was developed to reduce particle size and increase dispersion on the support in a consistent manner for a Pd₈₈W₁₂/C electrocatalyst. The spray-assisted method resulted in decreased particle size, improved dispersion and more uniform drying compared to a conventional method. These differences resulted in greater performance during operation of a single DMFC and PEMFC. Additionally, Pd₈₈W₁₂/C prepared by spray-assisted impregnation showed DMFC performance similar to Pt/C with similar particle size in the kinetic region while offering improved methanol tolerance. Pd₈₈W₁₂/C also showed comparable maximum power densities and activities normalized by cost in a PEMFC. Lastly, the activation of aluminum as an effective reducing agent for the wet- chemical synthesis of metallic particles by pitting corrosion was explored along with the control of particle morphology. It was found that atomic hydrogen, an intermediate, was the actual reducing agent, and a wide array of metals could be produced. The particle size and dispersion of Pd/C produced using Al was controlled using PVP and FeCl₂ as stabilizers. The intermetallic Cu₂Sb was similarly prepared with a 20 nm crystallite size for potential use in lithium-ion battery anodes. Lastly, it was found that the shape of Pd produced with Al as a reducing agent could be controlled to prepare 10 nm cubes enclosed by (100) facets with potentially high activity for the ORR. / text

Proton exchange membrane fuel cells (PEMFC) and direct methanol fuel cells (DMFC) are drawing much attention as alternative power sources for transportation, stationary, and portable applications. Nafion membranes are presently used in both PEMFC and DMFC as electrolytes, but are confronted with a few difficulties: (i) high cost, (ii) limited operating temperature of < 100 °C, and (iii) high methanol permeability. With an aim to overcome some of the problems encountered with the Nafion membranes, this dissertation focuses on the design and development of a few materials systems for use in PEMFC and/or DMFC. The incorporation of hydrous Ta₂O₅·nH₂O into Nafion membrane as well as the electrodes is shown to help the cell to retain water to higher temperatures. Membrane-electrode assembly (MEA) consisting of the composite membrane shows better cell performance at 100 and 110 °C than that with plain Nafion membrane, and a high power density of ~ 650 mW/cm² at 100 °C is obtained with H₂ - CO mixture as the fuel due to a significant alleviation of the CO poisoning of the catalysts. Sulfonated poly(etheretherketone) (SPEEK) membranes with various sulfonation levels are prepared and investigated in DMFC. With a sulfonation level of ~ 50 %, the SPEEK membranes exhibit low methanol permeability and electrochemical performance comparable to that of Nafion at around 60 °C, making it an attractive low-cost alternative to Nafion. From a comparative study of the structural evolutions with temperature in 2 M methanol solution, it is found that the lower methanol permeability of SPEEK membranes is related to the less connected and narrower pathways for water/methanol permeation. The dry proton conductor CsHSO₄ shows a high proton conductivity of ~ 10⁻³ S/cm at temperatures > 140 °C and water is not needed for proton conduction. However, it is found that CsHSO₄ decomposes to Cs₂SO₄ and H₂S at 150 °C in H₂ atmosphere in contact with the Pt/C catalyst. Thus, new catalyst materials need to be explored for CsHSO₄ to be used in practical high temperature PEMFC. Thin self-humidifying Nafion membranes with dispersed Pt/C catalyst powder are prepared and tested in PEMFC with dry H₂ and O₂. The Pt/C particles provide sites for catalytic recombination of H₂ and O₂ permeating from the anode and cathode, and the water produced at these sites directly humidifies the membrane. The performance of the cell with the self-humidifying membrane operated with dry reactants is ~ 90 % of that obtained with well humidified H₂ and O₂. / text