This diploma thesis deals with the design of a partially integrated charge pump in 0.25 micron technology ACMOS. The work is divided into two main parts, theoretical and practical. The theoretical section describes in detail various topologies of higher voltage generation of a charge pump and selected methods of regulating the output voltage of charge pumps. The practical part deals with the the actual design of a charge pump together with the arguments for the choice of the TPVD topology and the type of the regulation. Three regulation methods of a charge pump were implemented, tested and are dealt with: Pulse Skip, Constant frequency and PWM. There are 3 sub chapters, each describing a different regulation method, defining all the key elements of the design of such a charge pump and the results of the simulations are discussed. Conclusion of the thesis summarizes the results of the design of charge pumps, comparing them on the basis of the chosen type of output voltage regulation.

This thesis is focused on a creating supporting drivers and algorithms for electrical motor control using CPU TriCore TC275 CA. The first part is devoted to processor description and selected peripherals, which are A/D converter, a timer for creating the PWM signals and the second timer for processing singnals from encoder. All drivers are tested on an aplication kit, which is equipped with TC275 CA processor. The second part analyzes the measurement quality of GMR sensor TLE5009. Special testbench was prepared for sin cos data capturing and for their comparison with precise encoder position measurement. It was composed from DC motor having both sensor types on commons shaft. Data are acquired using LabView. Subsequently, it analyzes the sensor data, their compensation and subsequent comparison with measured data from the encoder.

This work deals with three-phase active rectifier control. In first, theoretical part it describes several control strategies with focus on voltage oriented control. For this type of control a design is worked out, and created model and its simulation is described. Second, practical part deals with realisation on microcontroller TMS320F28335, which is main processing unit of device lent by company Elcom. Therefore in this part abilities and settings of the controller along with developped control algorithm are described. Reached results of measurement are then presented and in the conclusion they are evaluated.

The thesis describes design and construction of vibration generator driver. The device is controlled via standard Ethernet interface and allows user to change parameters of generated function in PC application which reads and evaluates frequency and amplitude from real-time measured data while the test is running. In the introduction, vibration tests and choice of generators and power amplifiers are described. Next part is focused on every aspect of the hardware design. Last two chapters implement firmware for all three microcontrollers and software for PC application.

No description available.

No description available.

No description available.

This thesis deals with design and implementation of a versatile control unit, which is primarily designed for control of solar collectors. It describes the various stages of design. First, the system of solar collectors is introduced. Its input-output parts are analyzed and the requirements are determined for the control unit. The characteristics of temperature sensors are examined, the work deals with continuous variable speed circulators. The following part is dedicated to hardware and software implementation of the objectives of the work. The boards were designed in Eagle design environment, the firmware was written in C programming language. In conclusion, the evaluation of the results of the proposed system and possible ways of its further development are discussed. The versatile control unit can be deployed in practice realistically.

Voltage source inverters (VSI) are popular in variable speed induction motor drive applications. Pulse width modulation (PWM) is employed to achieve variable voltage variable frequency output from a fixed DC bus voltage. The modulation method greatly influences the harmonic distortion in line current and the inverter switching loss. This thesis evaluates a few space vectorbased PWM techniques which reduce the harmonic distortion and/or the inverter switching loss, compared to conventional space vector PWM (CSVPWM), at a given average switching frequency. In space vector-based PWM, the average voltage vector applied over a sub-cycle equals the commanded reference vector, thereby maintaining voltsecond balance. The given average vector can be realized by applying the voltage vectors of the inverter in different sequences. CSVPWM employs a switching sequence in which all the phases switch once in a sub-cycle. Sequences, in which a phase is clamped, while the other two phases switch once in a sub-cycle have been reported in literature. Further, certain special switching sequences have also been reported recently. These special sequences involve switching a phase twice, while switching the second phase once and clamping the third phase in a sub-cycle. This work investigates the use of such special switching sequences to reduce line current distortion and inverter switching loss in an induction motor drive. The influence of various switching sequences on line current ripple and inverter switching loss is discussed in the thesis. Comparison of the sequences in terms of switching loss leads to a hybrid PWM technique, which deploys the best sequence to reduce switching loss under a given operating condition. This technique is referred to as minimum switching loss PWM (MSLPWM). Further, a procedure for design of hybrid PWM techniques to achieve reduced line current distortion as well as inverter switching loss is elaborated. Four such specially designed hybrid PWM techniques are discussed. Analytical methods are presented for the evaluation of total RMS harmonic distortion factor of line current and inverter switching loss corresponding to different PWM techniques. The MSLPWM and the hybrid PWM techniques are evaluated analytically in terms of harmonic distortion and switching loss. It is observed that the switching loss corresponding to MSLPWM is considerably less than that with CSVPWM over the entire range of power factor. The reduction in switching loss with MSLPWM is as high as 36% at high power factors close to unity, while it is not less than 22% at power factors close to zero. MSLPWM also reduces the harmonic distortion for power factors close to unity at high modulation indices. Compared to CSVPWM, the hybrid PWM techniques result in a maximum reduction of about 40% in the harmonic distortion at fundamental frequencies close to 50Hz, and about 30% reduction in switching loss at power factors close to unity. The various PWM techniques are tested on a constant V /f induction motor drive with a digital control platform based on ALTERA Cyclone II field programmable gate array (FPGA) device. With a 10kVA IGBT based inverter feeding a 2.2kW, 415V, 50Hz, three-phase induction motor, the total RMS harmonic distortion factor of line current (IT HD) is measured at different fundamental frequencies for the various PWM techniques. The average switching frequency is 2.44kHz. The measured values of IT HD show a reduction in distortion with the hybrid PWM techniques over CSVPWM at high speeds of the drive. The relative values of IT HD corresponding to different PWM techniques agree with the theoretical predictions. With the 10kVA IGBT based inverter feeding a 6kW, 400V, 50Hz, 4pole, three-phase induction motor, the switching losses corresponding to CSVPWM and MSLPWM are evaluated and compared. This is done by measuring the steady state temperature rise of the heat sink over the ambient for the two techniques under different conditions. The thermal measurements are carried out at different loads with power factor ranging from 0.14 to 0.77. The measurements are also carried out at different fundamental frequencies (or modulation indices). Further, to separate conduction (constant) losses and switching (variable) losses, the heat sink temperatures are measured at two different switching frequencies, namely 2.44kHz and 4.88kHz. It is observed that the temperature rise due to MSLPWM is less than that due to CSVPWM consistently under various operating conditions. The thermal measurements confirm the theoretical prediction of reduction in switching loss with MSLPWM. Measurements of heat sink temperature rise corresponding to CSVPWM, MSLPWM and the hybrid PWM techniques are carried out at a higher power factor of 0.98 (lag) with the inverter feeding an RL load (instead of an induction motor). The hybrid PWM and MSLPWM result in lower switching losses as indicated by the reduction in temperature rise.

Multilevel converters are finding increased attention in industry and academia as the preferred choice of electronic power conversion for high power applications. They have a wide application area in a variety of industries involving transportation and energy management, a significant portion of which comprises of multilevel inverter fed induction motor drives. Multilevel inverters are ideally suitable for high power drives, since the switching frequency of the devices is limited for high power applications. In low power drives, the switching frequency is often in the range of tens of kHz, so that switching frequency harmonics are pushed higher in the frequency spectrum thereby the size and cost of the filter are reduced. But higher switching frequency has its own drawbacks, in particular for high voltage, high power applications. They cause large dv/dt stress on the motor and the devices, increased EMI problems and higher switching losses. An engineering trade-o is thus needed to select the minimum switching frequency without compromising on the output voltage quality. The present work is an alternate approach in this direction. Here, new inverter topologies and PWM strategies are developed that can eliminate a set of harmonics in the phase voltage using 12-sided polygonal space vector diagrams, also called dodecagonal space vector diagrams. A dodecagonal space vector diagram has many advantages over a hexagonal one. Switching space vectors on a dodecagon will not produce any harmonics of the order 6n 1, (n=odd) in the phase voltage. The next set of harmonics thus reside at 12n 1, (n=integer). By increasing the number of samples in a sector, it is also possible to suppress the lower order harmonics and a nearly sinusoidal voltage can be obtained. This is possible to achieve at a low switching frequency of the inverters. At the same time, a dodecagon is closer to a circle than a hexagon; so the linear modulation range is extended by about 6.6% compared to the hexagonal case. For a 50 Hz rated frequency operation, under constant V/f ratio, the linear modulation can be achieved upto a frequency of 48.3 Hz. Also, the harmonics of the order 6n 1, (n=odd) are absent in the over-modulation region. Maximum fundamental voltage is obtained from this inverter at the end of over-modulation region, where the phase voltage becomes a 12-step waveform. The present work is developed on dodecagonal space vector diagrams. The entire work can be summarized and explained through Fig. 1. This figure shows the development of hexagonal and dodecagonal space vector diagrams. It is known that, 3-level and 5-level space vector diagrams have been developed as an improvement over 2-level ones. They Figure 1: Development of hexagonal and dodecagonal space vector diagrams have better harmonic performance, reduced dv/dt stress on the motor and devices, better electromagnetic compatibility and improvement of efficiency over 2-level space vector diagrams. This happens because the instantaneous error between the reference vector and the switching vectors reduces, as the space vector density increases in the diagram. This is shown at the top of the figure. In the bottom part, the development of the dodecagonal space vector diagram is shown, which is the contribution of this thesis work. This is explained in brief in the following lines. Initially, a space vector diagram is proposed which switches on hexagonal space vectors in lower-modulation region and dodecagonal space vectors in the higher modulation region. As the reference vector length increases, voltage vectors at the vertices of the outer dodecagon and the vertices from the outer most hexagon is used for PWM control. This results in highly suppressed 5th and 7th order harmonics thereby improving the harmonic profile of the motor current. This leads to the 12-step operation at rated voltage where all the 5th and 7th order harmonics are completely eliminated. At the same time, the linear range of modulation extends upto 96.6% of base speed. Because of this, and the high degree of suppression of lower order harmonics, smooth acceleration of the motor upto rated speed is possible. The presence of multilevel space vector structure also limits the switching frequency of the inverters. In the next work, the single dodecagonal space vector diagram is improved upon to form two concentric dodecagons spanning the space vector plane (Fig. 1). The radius of the outer dodecagon is double the inner one. It reduces the device rating and the dv/dt stress on the devices to half compared to existing 12-sided schemes. The entire space vector diagram is divided into smaller sized isosceles triangles. PWM switching on these smaller triangles reduces the inverter switching frequency without compromising on the output voltage quality. The space vector diagram is further refined to accommodate six concentric dodecagons in the space vector plane (Fig. 1). Here the space vector diagram is characterized by alternately placed dodecagons which become closer to each other at higher radii. As such the harmonics in the phase voltage are reduced, in particular at higher modulation indices. At the same time, because of the dodecagonal space vector structure, all the 6n ± 1, (n=odd) harmonics are eliminated from the phase voltage. A nearly sinusoidal phase voltage can be generated without resorting to high frequency switching of the inverters. The above space vector diagrams are developed using different inverter circuits. The first work is developed from cascaded combination of three 2-level inverters, while the second and third works use 3-level NPC inverters feeding an open end induction motor drive. The circuit topologies are explained in detail in the respective chapters. Apart from this, PWM switching schemes and detailed analysis on duty cycle calculations using the concept of volt-second balance are also presented. They show that with proper switching schemes, the proposed configurations can substantially reduce the overall loss of the inverter. Other operational issues like capacitor voltage balancing of 3-level NPC inverters and improvement of input current drawn from the grid are also covered. All the above propositions are first simulated by MATLAB and subsequently verified by an experimental laboratory prototype. Motor current waveforms both at steady state and transient conditions during motor acceleration show that the induction motor can be fed from nearly sinusoidal voltage at all operating conditions. Simplified comparative studies are also made with the proposed converters and higher level inverters in terms of output voltage quality and losses. These are some of the constituents for chapters 2, 3 and 4 in this thesis. Additionally, the first chapter also covers a brief survey on some of the recent progresses made in the field of multilevel inverter. The thesis concludes with some interesting ideas for further thought and exploration.