In this project, a numerical model describing the reaction mechanism and the mass and energy transport in wood pyrolysis is studied. The applicability of the model in predicting actual biomass pyrolysis assessed by comparing the model to TGA experimental measurements. The comparison to experiments is done in relation to the mass loss characteristics of chips of varying sizes. The mass loss is of interest as it is a variable necessary in the coupling of reactor and particle models. Three reaction models were simulated and results compared to experimental data, namely, the reaction model developed by Park et al. [Combustion and Flame 157 (2010) 481-494], a simple multicomponent parallel reaction model, and a competitive reaction model. The model of Park et al. did not fit with the experimental data as it underestimates the char yield. The parallel reaction model, which is based on hemicellulose and cellulose decomposition to char and volatiles, also did not agree with the experiments even when fitting the parameters to the data. The downward trend of char yield with increasing temperature suggests there exists competition between the volatiles and char in wood pyrolysis. The proposed competitive reaction model which consists of a hemicellulose reaction to volatiles and a cellulose reaction to volatiles and char is in good agreement with the experimental data. The mass loss characteristics in the experimental temperature range is fairly predicted within reasonable accuracy.

<p dir="ltr">Partial methane oxidation (PMO) to methanol is a desirable route for upgrading natural and shale gas resources to liquid chemical intermediates and has been extensively studied on Cu-zeolites. Prior work has studied the stoichiometric PMO reaction on O₂-activated Cu-zeolites, leading to several proposals for candidate O_x-bridged Cu active site structures. More recent studies have investigated the catalytic PMO reaction and have reported that Cu-chabazite (CHA) zeolites tend to exhibit the highest methane oxidation rate (per Cu) among other Cu-zeolite topologies. Multiple studies have reported that decreasing the Cu site density and increasing the framework Al density increase the selectivity towards methanol, but have proposed different mechanistic explanations. Here, we study the influence of Cu active site distribution, which was altered by varying the extraframework Cu site density and the arrangement of framework Al atoms, on the kinetic parameters governing continuous PMO. The number of redox active Cu species was quantified through linear combination fitting of XANES spectra collected under <i>in situ</i> and transient conditions after reactant (O₂) cut-off, and the Cu speciation was investigated with XAS. Total methane oxidation rates and individual product formation rates (CH₃OH, CO, CO₂), normalized per total Cu, increased with Cu density because this influenced the speciation of Cu formed during the reaction. All Cu-CHA samples showed PMO rates that were nearly first-order in CH₄ pressure, consistent with prior reports that C-H activation in CH₄ is the rate limiting step. Samples with differing framework Al arrangement, but fixed extraframework Cu density, showed formation rates of over-oxidation products (e.g., CO₂) that had different apparent reaction orders in O₂, implying differences in the Cu active sites formed during reaction. Changes to Cu oxidation states were monitored with <i>in situ</i> XAS. Samples were first subjected to an oxidative pretreatment (723 K, 5 kPa O₂) and then to catalytic PMO conditions to reach steady-state. Steady-state XANES spectra collected after O₂ was removed from the reactant stream showed the expected reduction from Cu(II) to Cu(I), and the fraction of CH₄-reducible Cu(II) sites decreased with increasing Cu content; increasing the CH₄ pressure ten-fold increased the number of CH₄-reducible sites by a factor of ~1.5. These spectroscopic and kinetic observations suggest there are a mixture of Cu site types that are present during catalysis, each with different intrinsic reactivity toward CH₄ and selectivity to CH₃OH. To rationalize these observations, a reaction mechanism is proposed for a two-site model and used to derive rate expressions that describe apparent reaction orders for the total CH₄ oxidation rate and product formation rates on Cu-CHA zeolites of varying Cu content.</p><p dir="ltr">Additional routes for CH₄ activation include partial CH₄ oxidation over Fe zeolites that convert CH₄ at ambient temperature following an activation in nitrous oxide (N₂O), or through CH₄ dehydroaromatization (DHA) to benzene over Mo zeolites under non-oxidative conditions. Prior work on PMO over Fe-zeolites has identified candidate active site structures, but the influence of zeolite structural properties on ion-exchanged Fe speciation remains unclear. This work sought to understand the interaction of Fe with the zeolite framework during solvent-assisted deposition procedures and subsequent thermal treatments. In pursuit of this objective, Fe uptake isotherms were measured, and Fe speciation was characterized with UV-Vis spectroscopy and H₂ temperature programmed reduction (H₂ TPR). Increased framework Al site pairing increased the uptake of Fe in CHA zeolites, and high temperature treatments (723 K) resulted in the formation of oligomeric Fe structures as indicated by UV-vis. In CH₄ DHA over Mo-MFI, a principal challenge is the irreversible loss of catalytic reactivity with repeated reaction-regeneration cycles, attributed to dealumination of the zeolite structure during high-temperature oxidative regeneration treatments that produce steam. CHA zeolites are known to be more resistant to dealumination than MFI, but its smaller pore structure prevents diffusion of benzene and other aromatic products leading to rapid coking. This work attempted to address the diffusion limitations for benzene in Mo-CHA by synthesizing crystals with nanoscale dimensions by incorporating a surfactant into the crystallization procedure, generating solids with a flake-like morphology.</p><p dir="ltr">The overarching strategy in this work was to influence the speciation of metal sites and complexes in zeolites by controlling the density and arrangement of anionic Al anchoring sites within the framework and the density of extraframework metal species. In the case of Cu-zeolites, the amount of Cu present on the material influences the structures that form during catalysis that influences both the rate and selectivity of catalytic PMO.</p>

A bench-scale tubular reactor with recirculation was built in order to study the efficiency of the photocatalytic oxidation of phenol on fluidized titanium oxide-coated silica gel beads. A UV-C lamp placed along the central vertical axes of the reactor was used as source of photons. A bed of silica gel beads was fluidized by means of fluid recirculation and forced to follow upward helical flow around the lamp. Anatase was successfully synthetized on silica gel particles of average diameters 224, 357 and 461 µm, as confirmed by scanning electron micrographs, through a sol-gel technique using a titanium (iv)isopropoxide / hydrochloric acid / ethanol precursor. Data was obtained from multiple 8-hours photocatalytic experiments using a determined mass of beads fluidized in an aqueous solution of known initial phenol concentration. Contaminant degradation with irradiation time was measured as COD. Beads that had been subjected to three consecutive coating procedures produced an 8-h removal efficiency 10% higher than beads with a single coat. 20 g L-1 of silica beads was found to be the optimum load for the experimental reactor configuration regardless of beads size, although efficiency increased with decreasing size of the latter. Experimental results confirmed that the efficiency of phenol photocatalytic degradation decreases with increasing pollutant concentration. Also, the highest removal was achieved with initial pH 3, and it decreased with increasing pH. When NaCl was added to the solution, COD removal increased with increasing salinity. Additionally, it was found that dissolved oxygen is indispensable for photocatalysis to proceed, and that saturation of the treated mixture with oxygen was effectively achieved by keeping the liquid surface in contact with pure oxygen at 1 atm. Finally, statistical analysis of the data showed that photocatalytic mineralization of phenol-derived COD under the experimental conditions follows exponential decay. Based on this finding, a correlation model was proposed for the accurate prediction (minimum R2 = 0.9840) of the COD removal efficiency of the reactor for any given initial COD.

In this work, we design a linear, two step implicit finite difference method to approximate the solutions of a biological system that describes the interaction between a microbial colony and a surrounding substrate. Three separate models are analyzed, all of which can be described as systems of partial differential equations (PDE)s with nonlinear diffusion and reaction, where the biological colony grows and decays based on the substrate bioavailability. The systems under investigation are all complex models describing the dynamics of biological films. In view of the difficulties to calculate analytical solutions of the models, we design here a numerical technique to consistently approximate the system evolution dynamics, guaranteeing that nonnegative initial conditions will evolve uniquely into new, nonnegative approximations. This property of our technique is established using the theory of M-matrices, which are nonsingular matrices where all the entries of their inverses are positive numbers. We provide numerical simulations to evince the preservation of the nonnegative character of solutions under homogeneous Dirichlet and Neumann boundary conditions. The computational results suggest that the method proposed in this work is stable, and that it also preserves the bounded character of the discrete solutions.

<p>      </p> <p>Full exploitation of shale resources requires new catalytic techniques to efficiently convert the methane, ethane, and propane found in shale gas to value-added fuels and chemicals. A promising process of converting ethane and propane involves catalytic light alkane dehydrogenation and the subsequent oligomerization of light alkenes. The first part of this work focuses on the examination of the mechanistic details of propane dehydrogenation on Pt-based alloy catalysts, where first principles-based free energy, microkinetic, and degrees of rate control analyses are performed to understand and rationalize the selective propane dehydrogenation using a Pt3Mn alloy. We show that only the under-coordinated, Mn-decorated Pt sites, represented by a Pt3Mn(211) surface, are selective to propylene formation, which can be attributed to several key mechanistic details: (1) facile propylene desorption and (2) hindered pathways that are inherently non-selective to propylene and lead to the formation of isomers. These kinetic details can, in turn, be interpreted using the free energy landscapes of propane dehydrogenation on the Pt3Mn(211) surface, which features a reasonably stronger binding of propylene than those of its isomers. From this study, we extract two selectivity descriptors for propane dehydrogenation: The energetics of propylene desorption versus deep-dehydrogenation, as well as the energetics of the formation of propylene versus its isomers. The properties can be used for designing further improved light alkane dehydrogenation catalysts.</p>

<p dir="ltr">Metal speciation and structure can be influenced by the deposition method used during synthesis, interactions with the support, and by post-deposition treatments and reaction conditions experienced during its lifetime of carrying out a catalytic reaction. Supported metal particles of different size contain different surface structures and coordination environments, which may not only influence reaction rates but also the interconversion between agglomerated metallic domains and dispersed metal atom or ion sites. Here, we address the influence of post-deposition treatments and support properties on the structural interconversion of Pd and Cu on aluminosilicate chabazite (CHA) zeolites, Pt on gamma-alumina (γ-Al2O3), and Pd on amorphous oxides (γ-Al2O3, La-doped Al2O3, ΘΔ-Al2O3). The fundamental insights from these studies can be used to design catalysts used widely in automotive exhaust aftertreatment systems, including Pd-exchanged zeolites for passive NOx (x = 1,2) adsorbers (PNA), Cu-exchanged zeolites for NOx (x = 1,2) selective catalytic reduction (SCR), Pt/Al2O3 for NH3 oxidation, and Pd/oxides for three-way catalysts (TWC). Incipient wetness impregnation (IWI) and colloidal methods were used to prepare Pd nanoparticles deposited on CHA zeolites with distinct Pd nanoparticle sizes and distributions. These Pd-CHA samples were used to investigate the effects of Pd particle size distribution on structural interconversion between ion-exchanged Pd and agglomerated Pd domains under realistic operating conditions. Smaller Pd nanoparticles had larger fractions of agglomerated Pd that converted to ion-exchanged Pd2+ sites at fixed air treatment temperatures (598–973 K) and H2O pressures (2–6 kPa H2O), consistent with thermodynamic predictions from DFT calculations. Furthermore, the addition of H2O during air treatment of different Pd nanoparticles (2–14 nm) inhibited the formation of ion-exchanged Pd2+ (thermodynamics), but not the rate of redispersion (kinetics). This demonstrates that, regardless of Pd nanoparticle size, water vapor in automotive exhaust streams facilitate metal sintering in PNA applications. Aqueous-phase exchange of Cu on CHA zeolites with varying support properties (i.e., number of paired Al sites in the 6 membered ring) were used to prepare materials with distinct types and numbers of extraframework Cu species (Cu2+, CuOH+). These Cu-CHA materials were used to analyze Cu structural changes before and after exposure to hydrothermal aging conditions. In the absence of H2O, some Cu2+ sites condense to form binuclear Ox-bridged Cu species that can be reduced with H2 to form Cu-hydride sites and reject H2O, leading to a sub-stoichiometric H2 consumption (H2/Cu < 0.5). In the presence of H2O, all nominally isolated Cu2+ species convert to [CuOH]+ structures, which can subsequently be reduced by H2 to form a Cu-hydride and reject H2O, leading to stoichiometric H2 consumption (H2/Cu ~ 0.5). Furthermore, the presence of H2O led to reduction features in H2 temperature programmed reduction (TPR) profiles that were similar among Cu-CHA materials, regardless of the initial Cu2+ speciation, further supporting the proposal that all nominally isolated Cu2+ sites convert to a similar [CuOH]+ motif. This demonstrates how water influences Cu speciation on CHA materials of varying origin or treatment history, aiding in quantifying SCR-active isolated Cu ions and SCR-inactive Cu species (e.g., CuO, CuAl2O4). Pt supported on γ-Al2O3 were prepared with different average Pt particle sizes (2–13 nm) by increasing the temperature of post-deposition air treatment (523–873 K). This suite of materials was interrogated to isolate the effects of Pt particle size on NH3 oxidation rates and selectivities during conditions relevant to NH3 slip applications in diesel exhaust aftertreatment. For all Pt particle sizes, NH3 oxidation rates displayed a hysteresis with temperature, with high rates measured during temperature decreases than during temperature increases. Smaller Pt particles (2 nm) had lower rates (per surface Pt, quantified by CO chemisorption) than larger Pt particles (13 nm), signifying that NH3 oxidation is a structure-sensitive reaction. Furthermore, surfaces of Pt particles restructure under NH3 oxidation reaction conditions, influencing effective Pt oxidation states, surface structures (numbers and types of exposed Pt sites), and surface coverages of intermediates leading to the observed hysteresis in rate. These findings demonstrate that Pt particles undergo dynamic structural changes during reaction, influencing their ability to convert NH3 to environmentally benign products in NH3 slip applications. The influence of treatment conditions, support properties, and initial Pd particle size and distribution on the kinetics of nanoparticle sintering were investigated to identify which material properties allow maintaining high dispersion to maximize metal utilization for three way catalysts (TWC) during the conversion of regulated pollutants (CO, hydrocarbons, NOx). Pd was deposited by IWI methods to generate polydiserse particle size distributions, and using colloidal Pd nanoparticle solutions to generate monodisperse size distributions, onto various supports (γ-Al2O3, La-doped Al2O3, ΘΔ-Al2O3) and subjected to aging under oxidative and reductive conditions relevant for TWC operation. The average Pd particle size for all materials increased with treatment time under both reductive and oxidative environments. For samples prepared with IWI (i.e., log normal distribution of Pd particle sizes), reductive aging treatments led to higher sintering rates than oxidative treatments. In contrast, for samples prepared using colloidal Pd solutions (i.e., normal distribution of Pd particle sizes), oxidative aging treatments led to higher sintering rates than reduction treatments. Furthermore, after the same treatment condition and time, samples prepared with IWI resulted in higher average Pd particle sizes. These results indicate that more monodisperse initial Pd particle size distributions lead to lower sintering rates, providing guidance to design of supported metal TWCs with improved metal utilization during their lifetimes. Here, the combination of synthesis approaches to prepare a suite of model (e.g., powder) supported metal catalysts of varying structure and composition, interrogated using site and structural characterizations and steady-state and transient kinetic measurements, along with predictions from theoretical calculations, enabled unraveling the influence of material properties and gas environments that affect metal speciation, structure, and oxidation state in real-world aftertreatment systems that use more complex catalytic architectures (e.g., layered washcoats) and reactor designs (e.g., monoliths). This approach provides insights into the fundamental thermodynamic and kinetic factors influencing metal restructuring and interconversion under realistic conditions encountered in automotive exhaust aftertreatment applications, and the kinetic and mechanistic factors that underlie complex phenomena (e.g., reaction rate hysteresis) from data measured in the absence of hydrodynamic artifacts. The overall approach used in this work enabled development of synthesis-structure-function relationships on various metal supported catalysts for automotive exhaust aftertreatment applications, which can provide guidance for material design and treatment strategies to form and retain desired metal structures throughout the material lifetime, including synthesis, reaction, and regeneration treatments.</p>

<p dir="ltr">Zeolites are microporous crystalline aluminosilicates that are widely used as catalysts for upgrading hydrocarbons and oxygenates to higher value chemicals and fuels. The substitution of tetrahedral Si⁴⁺ with Al³⁺ in a charge-neutral silica framework ([SiO_4/2]) generates anionic centers ([AlO_4/2]^-), which charge-compensate Brønsted acid protons (H⁺) that serve as active sites for catalysis. Brønsted acid sites in aluminosilicates of diverse topologies have similar acid strength, but can be located within varying intracrystalline (or internal) microporous environments (0.4‒2 nm diameter) or at extracrystalline (or external) surfaces and mesoporous environments (>2 nm diameter); yet, catalytic diversity exists, <i>even</i> for a fixed zeolite framework topology, because micropores impose constraints on molecular access to and from intracrystalline active sites and provide van der Waals contacts that influence the stabilities of reactive intermediates and transition states. Tailoring the material properties of a given zeolite framework for targeted catalytic applications requires strategies to design both the bulk crystallite properties (e.g., morphology, active site density) that influence intracrystalline diffusion and the secondary environments that surround active sites and influence intrinsic kinetics, and further necessitates molecular-level insights to elucidate the influences of bulk and active site properties on catalysis. In this work, we provide synthetic and post-synthetic strategies to respectively tune active site environments within varying micropore voids and at external surfaces of zeolites, and develop gas-phase toluene methylation and liquid-phase mesitylene benzylation as probe reactions to quantify the catalytic consequences of active site environments on aromatic alkylation catalysis.</p><p dir="ltr">The MFI framework (orthorhombic phase) consists of 12 crystallographic distinct tetrahedral-sites and 26 unique framework oxygen atoms located around channels (~0.55 nm diameter) or channel intersections (~0.70 nm diameter). The synthesis of MFI zeolites using the conventional tetra-<i>n</i>-propylammonium (TPA⁺) organic structure directing agent (OSDA) is known to place framework Al and their attendant H⁺ sites within the larger intersection environments, because electrostatic interactions are favorable between such locations of [AlO_4/2]^- and the quaternary N⁺ center in TPA⁺ that becomes positioned rigidly within channel intersections during crystallization. The methylation of toluene by dimethyl ether (DME; 403 K) on MFI-TPA zeolites of fixed active site densities (~2 Al per unit cell) result in <i>ortho</i>-xylene (<i>o</i>-X; ~65%) as the major product over <i>para</i>-xylene (<i>p</i>-X; ~27%) and <i>meta</i>-xylene (<i>m</i>-X; ~8%). In contrast, toluene methylation on MFI zeolites (~2 Al per unit cell) synthesized using non-conventional OSDAs, such as ethylenediamine (EDA) or 1,4-diazabicyclo[2.2.2]octane (DABCO), predominantly forms <i>p</i>-X (~75%) over <i>o</i>-X (~23%) and <i>m</i>-X (~2%). Within the subsets of MFI-TPA and MFI-EDA/DABCO zeolites, measured xylene formation rates and isomer selectivities are independent of crystallite sizes (0.1‒13 µm), toluene conversions (0.02‒2.0%) and external H⁺ content (up to 9% external H⁺ per total Al), indicating negligible effects of diffusion-enhanced secondary xylene isomerization reactions at intracrystalline or extracrystalline domains. The invariance of xylene isomer selectivity with reactant pressures (0.2‒9 kPa toluene, 25‒66 kPa DME) or methylating agent (1‒4 kPa methanol) indicate that differences in reactivity of toluene to form each xylene isomer reflects differences in the stabilities of their respective kinetically relevant transition states that share the same reactive intermediate. Measured xylene isomer formation rate constants and rate constant ratios, obtained from mechanism-derived rate expressions and interpreted using transition state theory formalisms, are used alongside density functional theory (DFT) calculations to reveal that intersection void environments (~0.70 nm diameter) similarly stabilize all three xylene transition states over unconfined surfaces (>2 nm diameter) without altering the established aromatic substitution patterns, while channel void environments (~0.55 nm diameter) preferentially destabilize bulkier <i>o</i>-X and <i>m</i>-X transition states thereby resulting in high intrinsic <i>p</i>-X selectivity. DFT calculations reveal that the ability of protonated DABCO complexes to reorient within MFI intersections and participate in additional hydrogen-bonding interactions with anionic Al centers during synthesis, facilitates the placement of Al in smaller channel environments that are less favored by TPA⁺. These molecular-level details, enabled by combining synthesis, characterization, kinetics and DFT, establish a mechanistic link between OSDA structure, active site placement and transition state stability, and provide active site design strategies orthogonal to crystallite design approaches that rely on complex reaction-diffusion phenomena.</p><p dir="ltr">For various reactions including toluene methylation at higher reaction temperatures (573‒773 K) and toluene conversions (>10%), extracrystalline H⁺ sites in MFI zeolites are reported to influence reactivity, selectivity, and deactivation behavior during catalysis in undesired ways. Post-synthetic chemical treatments to passivate external H⁺ sites on MFI zeolites result in unintended (but not always undesirable) changes to bulk structural properties and Al and H⁺ contents. The number of extracrystalline H⁺ sites is difficult to quantify using conventional spectroscopic or titrimetric methods, especially when present in dilute amounts on samples whose surfaces have been passivated. The systematic treatment of MFI zeolites (2.4, 5.7 and 7.1 Al per unit cell) using ammonium hexafluorosilicate (AHFS) at varying treatment duration times, AHFS concentrations and number of successive treatments resulted in MFI zeolites that retain their bulk structural properties and total Al and H⁺ contents, except for one parent MFI sample containing a significant amount of non-framework Al species. The benzylation of mesitylene by dibenzyl ether (363 K) occurs exclusively at external H⁺ sites because the bulky 1,3,5-trimethyl-2-benzylbenzene product is sterically prevented from forming at intracrystalline H⁺ sites. The intrinsic zero-order rate constant (per external H⁺) for mesitylene benzylation is extracted from rate measurements (per total Al) on a suite of untreated MFI samples with known amounts of external H⁺ sites (1‒15% external H⁺ per total Al) quantified using bulky 2,6-di-<i>tert</i>-butylpyridine base titrants. Measured zero-order rate constants on AHFS-treated MFI zeolites are used to quantify the extent to which AHFS treatments passivate external H⁺ sites, revealing efficacies that depend on the specific treatment conditions and the parent sample used. The developed kinetic methods demonstrate the utility of catalytic probes, when compared to stoichiometric probes based on spectroscopic or titration methods, in amplifying and quantifying dilute concentrations of external H⁺ sites on zeolites. The methods enable comparisons of the efficacy of various post-synthetic passivation strategies and permit rigorous assessments of the influence of external H⁺ during acid catalysis.</p><p dir="ltr">Overall, this work provides (post-)synthetic strategies to tune active site environments within intracrystalline micropores or at extracrystalline surfaces and develops quantitative kinetic probes that enable a molecular-level understanding of catalytic consequences of active site environments on aromatic alkylation reactions. Taken together, the methodology and findings of this study have broader implications in zeolite catalyst design for selectively upgrading traditional fossil feedstocks (crude oil and shale gas) and emerging feedstocks (biomass and waste plastics).</p>

Chemical modification of proteins is critical for many areas of biochemistry and medicine. Several methods for site-selective protein modification are reported in this Thesis that are useful in accessing both natural and artificial protein architectures. Multiple, complementary methods for the conversion of cysteine to dehydroalanine are described. Dehydroalanine is used as a general precursor to several post-translational modifications and glycosylation, polyprenylation, phosphorylation, and lysine methylation and acetylation are all accessible. These modifications and their mimics were explored on multiple proteins, including histone proteins. Unnatural modifications were also explored. The first examples of olefin metathesis and Suzuki-Miyaura cross-coupling on protein substrates are reported. Allyl sulfides were discovered to be remarkably reactive substrates in olefin metathesis, allowing use of this reaction in water and on proteins. For Suzuki-Miyaura cross-coupling, a new catalyst is described that is fully compatible with proteins. Both olefin metathesis and cross-coupling allow the formation of carbon-carbon bonds on proteins. The prospects of these transformations in chemical biology are discussed. Finally, a novel strategy is reported for the installation of natural, unnatural, and post-translationally modified amino acid residues on proteins. This technology relies on addition of carbon radicals to dehydroalanine. This method of "chemical mutagenesis" is anticipated to complement standard genetic manipulation of protein structure.

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NOx emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH2)2CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation. Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, aqueous urea also works as a reducing agent by breaking down into ammonia (NH3) and Cyanuric Acid ((HOCN)3). These compounds serve as the primary reducing agents in the NOx reduction mechanism explored here. The main reducing agent, aqueous urea, was admixed with glycerol (C3H8O3) in an 80-20 ratio, by weight, to function as a lubricant for the secondary injector. The aqueous urea injection timing and duration is critical to the reduction of NOx emissions due to the dependence of SNCR NOx reduction on critical factors such as temperature, pressure, reducing agent to NOx ratio, Oxygen and radical content, residence time and NH3 slip. From scoping engine tests at loads of 40 percent and 80 percent at 1500 rpm, an aqueous urea injection strategy was developed. The final injection strategy chosen was four molar ratios, 4.0, 2.0, 1.0 and 0.5 with five varying injection timings of 60, 20, 10, 0, and -30 degrees after top dead center (ATDC). In addition to the base line and aqueous urea tests, water injection and an 80-20 water-glycerol solution reduction agent tests were also conducted to compare the effects of said additives as well. The comparison of baseline and SNCR operation was expected to show that the urea acted as a reducing agent, lowering NOx emissions up to 100% (based on exhaust stream studies) in the diesel exhaust gas without the aid of a catalyst. The data collected from the engine tests showed that the aqueous urea-glycerol solution secondary had no effect on the reduction of NOx and even resulted in an increase of up to 5% in some tests. This was due to the low average in-cylinder temperature as well as a short residence time, prohibiting the reduction reaction from taking place. The neat water and water-glycerol solution secondary injection was found to have a reduction effect of up to 59% on NOx production in the emissions due to the evaporative cooling effect and increased heat capacity of the water.

<p> Wire-wrapped rod bundles are often used in nuclear reactors operating in a fast neutron spectrum, as designers seek to minimize neutron scattering by packing the fuel pins into a hexagonal lattice. Bundles with many rods have extensively been studied as representative of large fuel assemblies, however far fewer experiments have investigated bundles with 7 rods (7-pin bundles). The large difference in subchannel number between these bundles leads to 7-pin bundles having different pressure drop characteristics. The Versatile Test Reactor (VTR) sodium cartridge loop proposes to use a 7-pin bundle as its experimental core region, highlighting the need for additional data and models. The current work seeks to establish a better understanding of the pressure drop in 7-pin wire-wrapped rod bundles through scaled experiments and a novel pressure drop model. A scaling analysis is first performed to demonstrate the applicability of water experiments to the VTR sodium cartridge loop, before an experimental test facility is designed and constructed. Experiments are then performed at a range of Reynolds numbers to determine the pressure drop. Current models are able to predict the data well, but are complex and can be difficult to use. A comparatively simpler model is developed, based on exact laminar solutions of a simplified rod bundle, which also offers a theoretical lower bound for the pressure drop in wire-wrapped bundles. The proposed model compares well with the existing experimental database, able to predict bundle friction factor with an average absolute percent difference of 10.8%. This accuracy is also similar to existing correlations, while relying on fewer empirical coefficients. The theoretical lower bound is also used to identify several datasets in literature that may feature data that is systemically lower than the true pressure drop, which agrees with previous observations in literature. </p>