京都大学 / 0048 / 新制・課程博士 / 博士(エネルギー科学) / 甲第18383号 / エネ博第295号 / 新制||エネ||61(附属図書館) / 31241 / 京都大学大学院エネルギー科学研究科エネルギー基礎科学専攻 / (主査)教授 中村 祐司, 教授 岸本 泰明, 教授 前川 孝 / 学位規則第4条第1項該当 / Doctor of Energy Science / Kyoto University / DFAM

This thesis presents advanced torque control methods for torque ripple reduction and performance improvement in switched reluctance motor (SRM) drives. A new offline torque sharing function (TSF) method is proposed for torque ripple reduction in SRMs. The proposed TSF achieves lower current tracking error by establishing a new current reference generation strategy. The phase current reference is first derived from the torque command using offline calculations and also from the phase current response that is obtained from the dynamic model of the SRM. Then, an optimization problem is formulated to shape the current reference for the objective of minimizing the torque ripple and copper losses, while maintaining the required average output torque at the given operating speed. The dynamic simulation of the SRM model is also utilized in the optimization problem. A new online TSF method is proposed for torque ripple reduction in SRMs. The proposed TSF takes the current dynamics and induced electromotive force into account by establishing a new online current profile generation technique. First, a primary phase current reference derived from the torque reference is applied to the SRM. Then, the decaying phase current after the turn-off angle is sampled, and it is used to update the current reference. A new online optimization strategy is performed to shape the current reference during the operation of the machine. Owing to the proposed current profile generation technique, the optimization process is decoupled to independently minimize the torque ripple by optimizing the turn-on angle and minimizing copper losses by optimizing the turn-off angle. Compared to the conventional TSFs and existing optimization-based TSFs, the proposed two TSFs achieve accurate torque control, improved torque-speed capability, reduced torque ripple, and better current tracking performance. All the proposed TSF methods are validated by both simulations and experiments on a 3-phase, 12/8 SRM. / Dissertation / Doctor of Philosophy (PhD)

Battery-powered trends in consumer electronics, transportation, and renewable energy sectors increase demands on DC/DC converter technology. Higher switching frequency and efficiency reduces solution size and cost, while increasing power capabilities. Still, switching noise remains the primary drawback associated with any DC/DC converter. Reducing a converter’s input ripple helps prevent switching noise from spreading to other systems on a shared DC power bus. This thesis covers the analysis, simulation, and implementation of a recently-proposed boost converter topology, alongside an equivalent standard boost converter, operating in steady-state, continuous conduction mode. A Matlab-based simulation predicts each converter’s input ripple performance using a state-space model. The converters’ hardware implementation minimizes component and layout differences to create an equivalent comparison. The simulation and hardware measurements demonstrate a 40% input current ripple reduction using the modified topology. Replacing standard boost converters with the modified topology minimizes the switching noise conducted through a system’s DC power network.

<p> 49 beds of ripple-drift cross-lamination were measured in the Ordovician Cloridorme Formation of Gaspe, Quebec. Most of the beds are Bouma C (cross-laminated), some are BC (parallel lamination pas sing up into cross-lamination) and a few are AC and ABC types (graded bedding passing up into parallel and cross-lamination). </p> <p> Six climbing patterns have been recognised in the ripple-drift beds, namely: concave -upward, straight, sigmoidal, convex-upward, sinuous, and disconnected-irregular. Angles of climb range from 1 to 44 degrees. Commonly the angle of climb steepens up through the coset to about 1/2 or 3/4 of the coset thickness and then gradually flattens out until the bed is plane. </p> <p> Measurements of wave length, amplitude, stoss -angle, lee-angle, angle of climb and ratio of lee- to stoss-lamina thicknesses show that the wave length continues to increase upward, and the lee/stoss thickness ratio decreases upward through the coset. The amplitude, and stoss- and lee-angles increase upward through that portion of the coset in which the angle of climb increases upward. Simultaneously with the increase in amplitude and angle of climb, the shape of the foreset laminae becomes progressively more and more sigmoidal. </p> <p> Down-current changes in lamination types were recorded in several beds. The most interesting change is from parallel lamination down-current into ripple-drift, continuing downcurrent back into parallel lamination. </p> / Thesis / Master of Science (MSc)

Die Aktivität des Hippocampus im Tiefschlaf ist geprägt durch sharp wave-ripple Komplexe (SPW-R): kurze (50–100 ms) Phasen mit erhöhter neuronaler Aktivität, moduliert durch eine schnelle “Ripple”-Oszillation (140–220 Hz). SPW-R werden mit Gedächtniskonsolidierung in Verbindung gebracht, aber ihr Ursprung ist unklar. Sowohl exzitatorische als auch inhibitorische Neuronpopulationen könnten die Oszillation generieren. Diese Arbeit analysiert Ripple-Oszillationen in inhibitorischen Netzwerkmodellen auf mikro-, meso- und makroskopischer Ebene und zeigt auf, wie die Ripple-Dynamik von exzitatorischem Input, inhibitorischer Kopplungsstärke und dem Rauschmodell abhängt. Zuerst wird ein stark getriebenes Interneuron-Netzwerk mit starker, verzögerter Kopplung analysiert. Es wird eine Theorie entwickelt, die die Drift-bedingte Feuerdynamik im Mean-field Grenzfall beschreibt. Die Ripple-Frequenz und die Dynamik der Membranpotentiale werden analytisch als Funktion des Inputs und der Netzwerkparameter angenähert. Die Theorie erklärt, warum die Ripple-Frequenz im Verlauf eines SPW-R-Ereignisses sinkt (intra-ripple frequency accommodation, IFA). Weiterhin zeigt eine numerische Analyse, dass ein alternatives Modell, basierend auf einem transienten Störungseffekt in einer schwach gekoppelten Interneuron-Population, unter biologisch plausiblen Annahmen keine IFA erzeugen kann. IFA kann somit zur Modellauswahl beitragen und deutet auf starke, verzögerte inhibitorische Kopplung als plausiblen Mechanismus hin. Schließlich wird die Anwendbarkeit eines kürzlich entwickelten mesoskopischen Ansatzes für die effiziente Simulation von Ripples in endlich großen Netzwerken geprüft. Dabei wird das Rauschen nicht im Input der Neurone beschrieben, sondern als stochastisches Feuern entsprechend einer Hazard-Rate. Es wird untersucht, wie die Wahl des Hazards die dynamische Suszeptibilität einzelner Neurone, und damit die Ripple-Dynamik in rekurrenten Interneuron-Netzwerken beeinflusst. / Hippocampal activity during sleep or rest is characterized by sharp wave-ripples (SPW-Rs): transient (50–100 ms) periods of elevated neuronal activity modulated by a fast oscillation — the ripple (140–220 Hz). SPW-Rs have been linked to memory consolidation, but their generation mechanism remains unclear. Multiple potential mechanisms have been proposed, relying on excitation and/or inhibition as the main pacemaker. This thesis analyzes ripple oscillations in inhibitory network models at micro-, meso-, and macroscopic scales and elucidates how the ripple dynamics depends on the excitatory drive, inhibitory coupling strength, and the noise model. First, an interneuron network under strong drive and strong coupling with delay is analyzed. A theory is developed that captures the drift-mediated spiking dynamics in the mean-field limit. The ripple frequency as well as the underlying dynamics of the membrane potential distribution are approximated analytically as a function of the external drive and network parameters. The theory explains why the ripple frequency decreases over the course of an event (intra-ripple frequency accommodation, IFA). Furthermore, numerical analysis shows that an alternative inhibitory ripple model, based on a transient ringing effect in a weakly coupled interneuron population, cannot account for IFA under biologically realistic assumptions. IFA can thus guide model selection and provides new support for strong, delayed inhibitory coupling as a mechanism for ripple generation. Finally, a recently proposed mesoscopic integration scheme is tested as a potential tool for the efficient numerical simulation of ripple dynamics in networks of finite size. This approach requires a switch of the noise model, from noisy input to stochastic output spiking mediated by a hazard function. It is demonstrated how the choice of a hazard function affects the linear response of single neurons and therefore the ripple dynamics in a recurrent interneuron network.

No description available.

Power Factor Correction rectifiers are widely adopted as the first stage in most grid-tied power conversion systems. Among all PFC converts for single phase system, Boost PFC is the most popular one due to simplicity of structure and high performance. Although the efficiency of Boost PFC keeps increasing with the evolution of semiconductor technology, the intrinsic feature of high output voltage may result cumbersome system structure with multiple power conversion stages and even diminished system efficiency. This disadvantage is aggravated especially in systems where resonant converters are selected as second stage. Especially for domestic induction cooker application, step-down PFC with wide range output regulation capability would be a reasonable solution, Conventional induction cooker is composed by input filter, diode-bridge rectifier, and full bridge or half bridge series resonant circuit (SRC). High frequency magnetic field is induced through the switching action to heat the pan. The power level is usually controlled through pulse frequency modulation (PFM). In such configuration, first, a bulky input differential filter is required to filter out the high frequency operating current in SRC. Second, as the output power decreases, the operating point of SRC is moved away from the optimum point, which would result large amount circulating energy. Third, when the pan is made of well conducting and non-ferromagnetic material such as aluminum, due to the heating resistance become much smaller and peak output voltage of the switching bridge equals to the peak voltage of the grid, operating the SRC at the series resonant frequency can result excessive current flowing through the switch and the heating coil. Thus for pan with smaller heating resistance, even at maximum power, the operating frequency is pushed further away from the series resonant point, which also results efficiency loss. To address these potential issues, a PFC circuit features continuous conducting input current, high power factor, step-down capability and wide range output regulation would be preferred. The Analysis and design work is present in this article for a non-isolated hard switching DCM SEPIC PFC. Due to DCM operation of SPEIC converter, wide adjustable step-down output voltage, continuous conduction of input current and elimination of reverse recovery loss can be achieved at same time. The thesis begins with circuit operation analysis for both DC-DC and PFC operation. Based on averaged switching model, small signal model and corresponding transfer functions are derived. Especially, the impact from small intermediate capacitor on steady state value are discussed. With the concept of ripple steering, theoretic analysis is applied to SEPIC converter with two coupled inductors. The results indicate if the coupling coefficient is well designed, the equivalent input inductance can be multiple times larger than the self-inductance. Because of this, while maintaining input current ripple same, the two inductors of SEPIC can be implemented with two smaller coupled inductors. Thus both the total volume of inductors and the total number of windings can be reduced, and the power density and efficiency can be improved. Based on magnetic reluctance model, a corresponding winding scheme to control the coupling coefficient between two coupled inductors is analyzed. Also the impact of coupled inductors on the small signal transfer function is discussed. For the voltage follower control scheme of DCM PFC, single loop controller and notch filter design are discussed. With properly designed notch filter or the PR controller in another word, the closed loop bandwidth can be increased; simple PI controller is sufficient to achieve high power factor; THD of the input current can be greatly reduced. Finally, to validate the analysis and design procedure, a 1 kW prototype is built. With 120 Vrms AC input, 60V to 100V output, experimental results demonstrate unity power factor, wide output voltage regulation can be achieved within a single stage, and the 1 kW efficiency is around 93%. / Master of Science

For the future of sustainable energy, renewable energy will need to significantly penetrate existing utility grids. While various renewable energy sources are networked with high-voltage DC grids, integration between these high-voltage DC grids and the existing AC grids is a significant technical challenge. Among the limited choices available, the modular multi-level converter (MMC) is the most prominent interface converter used between the DC and AC grids. This subject has been widely pursued in recent years. One of the important design challenges when using an MMC is to reduce the capacitor size associated with each module. Currently, a rather large capacitor bank is required to store a certain amount of line-frequency related circulating energy. Several control strategies have been introduced to reduce the capacitor voltage ripples by injecting certain harmonic current. Most of these strategies were developed using trial and error and there is a lack of a systematic means to address this issue. Most recently, Yadong Lyu has proposed to control the modulation index in order to reduce capacitor ripples. The total elimination of the unwanted circulating power associated with both the fundamental line frequency and the second-order harmonic was demonstrated, and this resulted in a dramatic reduction in capacitor size. To gain a better understanding of the intricate operation of the MMC, this thesis proposes a state-space analysis technique in the present paper. Combining the power flow analysis with the state trajectory portrayed on a set of two-dimensional state plans, it clearly delineates the desired power transfer from the unwanted circulating energy, thus leading to an ultimate reduction in the circulation energy and therefore the required capacitor volume. / Master of Science

Im Hippokampus gibt es verschiedene Netzwerkoszillationen mit unterschiedlichen Frequenzen. Ein Typ dieser Oszillationen sind die ”Ripple” mit einer Frequenz von etwa 200 Hz, welche in Komplexen mit einer Aktivitätswelle, der ”Sharp wave” auftreten. Sharp wave-ripple Komplexe (SWR) werden mit der Konsolidierung von Gedächtnis in Zusammenhang gebracht. Das Netzwerk, das den SWR unterliegt, hat bestimmte Mechanismen, von denen einige in der vorliegenden Arbeit näher untersucht werden. Im ersten Teil wird untersucht, wie ein hemmendes Interneuron in der hippokampalen Region CA1, das ”oriens-lacunosum moleculare” (O-LM) Interneuron, während der SWR in das Netzwerk eingebunden ist. Wir konnten zeigen, dass O-LM Zellen während der SWR starke synaptische Exzitation erhalten. Die Exzitation tritt spät während des Ripples im lokalen Feldpotential (LFP) auf und zeigt eine Phasenankopplung an die Ripple. In etwa der Hälfte der O-LM Zellen konnten wir Aktionspotentiale während der SWR zeigen, die an die Ripple-Phase im LFP gebunden sind und nach dem Ripple-Maximum auftreten. Der zweite Teil der Arbeit bezieht sich auf die hippokampale Region CA1 und vergleicht während SWR den synaptischen Eingang in zwei Untertypen von Pyramidenzellen, die tiefen und die oberflächlichen Pyramidenzellen. Beide Untertypen bekommen synaptische Eingänge während der SWR. Diese Eingänge sind eine Mischung aus exzitatorischen und inhibitorischen Eingängen, die in den Untertypen in ihrer Stärke vergleichbar sind. Im dritten Teil untersuchen wir die SWR in der Region CA2 des Hippokampus und zeigen, dass Pyramidenzellen in CA2 in das Netzwerk während SWR eingebunden sind. Wir können sowohl exzitatorische als auch inhibitorische synaptische Eingänge in den Pyramidenzellen darstellen und konnten eine Phasenkopplung der synaptischen Eingänge an die SWR im LFP zeigen. Aufgrund der Phasenverschiebung bei verschiedenen Haltepotentialen vermuten wir einen Oszillator für die Exzitation und einen für die Hemmung. / In the hippocampus there are different patterns of activity also known as network oscillations. These oscillations express different frequencies, and one oscillation is the ripple oscillation at around 200 Hz. It is associated with an activity wave called sharp wave and form a so-called sharp wave-ripple complex (SWR). SWRs are implicated in memory consolidation. In this thesis we investigate mechanisms underlying sharp wave-ripple complexes. In the first part of this thesis I examine one type of inhibitory neurons in the region CA1 of the hippocampus during SWR. Oriens-lacunosum moleculare (O-LM) interneurons receive strong excitatory synaptic input during ripples. This input arrives after the ripple maximum and is phase locked with the ripple cycles. Around half of the probed O-LM cells fire during the SWR and thereby show an active participation during SWR. The magnitude of excitation in O-LM cells and the ratio between excitation and inhibition determine if an O-LM cell is active during the SWR. Action potentials in these cells occur late during the SWR and are phase locked. In the second part the synaptic input onto excitatory pyramidal cells were investigated during ripple oscillations. Previous work has identified two different types of pyramidal cells in area CA1. We recorded from deep and superficial pyramidal cells. For both types of pyramidal cells the inhibitory and excitatory synaptic inputs temporally associated with ripples express comparable strength. In the last and third part, I recorded SWR in the CA2 region of the hippocampus and showed incidence, frequency and amplitude of ripples and SWR. Pyramidal cells in the CA2 region are integrated into the network during SWR. They receive SWR associated synaptic input during SWR. The excitatory and inhibitory synaptic inputs in CA2 pyramidal cells were investigated in detail. Phase analysis show phase locking of local field potential ripples and synaptic inputs to the ascending phase of the ripple cycle.

Thesis (PhD) -- Macquarie University, Division of Information and Communication Sciences, Department of Computing, 2007. / "Submitted January 27 2007, revised July 27 2007". / Bibliography: p. 281-304. / Mode of access: World Wide Web. / xiv, 487 p., bound ill. (some col.)