Monolayers of the cationic surfactant hexadecyltrimethylammonium halide (CTAX, where X = F¯, Cl¯, Br¯, and I¯) have been studied at the air-water and oilwater interfaces. At the air-water interface, the effects of the halide counterion and the addition of counterion were investigated. Sum-frequency spectroscopy (SFS), ellipsometry, and surface tensiometry indicated that the counterion changed the efficiency and effectiveness of the surfactant, both decreasing in the order of Br¯> Cl¯>F¯. The addition of salt in the form of 0.1 M KX was found to reduce the cmc but had little effect on the limiting area per molecule attained at the cmc, which increased from 44 Ų for CTAB to 65 Ų for CTAC and ca. 94 Ų for CTAF. Neither SFS nor ellipsometry provided any firm evidence for specific effects of the halide ions on the structure of the surfactant monolayers. For CTAB monolayers in the absence of excess electrolyte, the effect of area per molecule on the sum-frequency (SF) spectra was studied. Mixed monolayers of CTAB and tetradecane at the air-water interface exhibit a first-order phase transition from a conformationally disordered to a conformationally ordered state as the temperature is lowered. The phase transition occurs ca. 11 °C above the bulk melting point of tetradecane. A new experimental arrangement is described for acquiring SF spectra from surfactants at the oil-water interface. The key features of this approach are the stabilisation of a thin oil film between a sapphire prism and an aqueous phase, and the use of total internal reflection to enhance the total signal and discriminate against signals from other interfaces in the system. With this new methodology, the first SF vibrational spectra of surfactant monolayers at an alkane-water interface were obtained. Surface tensiometry was used to characterise the monolayers further. The structure of CTAB monolayers at the hexadecane-water interface was determined by SFS and compared with monolayers of CTAB at the air-water interface. At low concentrations, CTAB/hexadecane showed the expected features in the C-H stretching region, characteristic of a conformationally disordered monolayer. As the bulk concentration approached the critical micelle concentration, the spectra changed to one characteristic of a more ordered, upright conformation. Ellipsometric measurements supported this conclusion. This qualitative structural change is not observed in analogous monolayers at the air-water interface or CCl₄-water interface, or in surfactant solutions in contact with a hydrophobic solid surface.

Ce mémoire de thèse présente le développement d'un dispositif expérimental spécialement conçu pour l'étude de la diffraction d'atomes rapides et son utilisation pour suivre la croissance de couches minces sur un bâti d'épitaxie. Des études de surfaces de KBr(100) et de NaCl(100) avec ce nouveau dispositif sont présentées. Nous nous sommes intéressés notamment à la forme du potentiel que les atomes perçoivent lorsqu'ils diffusent sur une surface de KBr(100). Nous avons également mis en évidence lors de ces études un nouveau régime de diffraction qui semble correspondre à des mouvements longitudinaux et normaux cohérents. Grâce à des images mieux résolues, nous avons montré comment la diffraction d'atomes rapides permet d'observer et quantifier des défauts topologiques comme la mosaïcité. Une étude d'une surface d'Argent (110) est aussi présentée. Elle a permis d'observer la diffraction d'atomes rapides sur les métaux, montrant ainsi que GIFAD est applicable aux trois types de matériaux (isolants, semi-conducteurs et métaux) et que les processus d’excitations électroniques sur ces surfaces ne détruisent pas complètement la cohérence. Enfin des premiers résultats de GIFAD en tant que technique de suivi de croissance par épitaxie sont présentés dans ce travail. / This Ph.D memoir presents the development work of an experimental setup especially designed for the study of the fast atom diffraction and its use as a method to control the thin films growth in an epitaxy chamber. Studies of the surfaces of KBr(100) and NaCl(001) with this new setup are presented. A new diffraction regime which may correspond to coherent longitudinal and normal motions is identified. The enhanced resolution allows observation of topological defects such as the surface mosaicity. A study of the Ag(100) surface is also presented showing that fast atom diffraction can be observed on metal surface as that the inelastic excitations processes do not completely destroy the coherence. Finally, we present the first results obtained with GIFAD as a method to control thin film growth.

Ce travail a permis de déterminer les structures atomique et électronique de deux surfaces d'alliages métalliques complexes à l'aide d'une approche multi-techniques supportée par des calculs ab intio de structure électronique. Les surfaces de ces cristaux ont pu être corrélées à certains plans présents dans les modèles structuraux disponibles. La terminaison dominante de la surface (100) d'Al13Co4 est identifiée comme un plan corrugué incomplet du volume. La surface (010) de Al3(Mn, Pd) présente un nombre conséquent d'imperfections structurales. À l'exception de certains sites lacunaires, elle est identique au plan corrugué complet du massif. Dans une seconde étape, ces échantillons ont été utilisés comme substrat pour la croissance de films minces métalliques. Les atomes de Pb déposés sur ces deux surfaces suivent un mode de croissance pseudomorphique jusqu'à la formation de la monocouche. Dans le cas de l'Al13Co4, le coefficient de collage du Pb s'annule une fois cette monocouche formée. Sur la surface Al3(Mn, Pd), le croissance de couches additionnelles de Pb est observée. L'adsorption du Cu sur Al13Co4 mène de nouveau à un mode de croissance pseudomorphique jusqu'à la monocouche. Au-delà de ce dépôt, la phase ß-Al(Cu, Co) apparaît en surface. Pour des dépôts à des températures plus élevées, la phase- ß est suivie par la formation de la phase ?-Al4Cu9. Les phases ß et ? croissent suivant deux domaines (110) orientés l'un par rapport à l'autre avec un angle de 72° / We report the investigation of pseudo-ten-fold surfaces on two complex metallic alloys considered as approximants to the decagonal quasicristal. The atomic and electronic structure of the both samples is investigated by means of a multi-technique approach supported by ab initio electronic structure calculations. The main termination of the (100) surface of Al13Co4 is attributed to an incomplete puckered layer. The (010) surface of Al3(Mn, Pd) exhibits an important amount of structural imperfections. With the exception of several vacancies, this surface is identical to the complete puckered layer. In a second stage, both surfaces have been used as templates for the growth of metallic thin films. On both surfaces, Pb adatoms adopt a pseudomorphic growth mode up to one monolayer. For the Al13Co4 surface, the sticking coefficient of Pb vanishes upon the completion of the monolayer. However, it remains sufficient for the growth of additional layers on the Al3(Mn, Pd) (010) surface. The adsorption of Cu on the Al13Co4 surface follows also a pseudomorphic growth mode up to one monolayer. The ß-Al(Cu, Co) phase appears for coverages greater than one monolayer. For higher temperature deposition, the ß-phase is followed by the formation of the ?-Al4Cu9 phase. Both ß and ? phases grow as two (110) domains rotated by 72° from each other

The work considers pulse wire-guided electromagnetic (EM) waves. The main contribution of the work is the original design of the isolation bushing for maximizing of the received wave (echo) thanks to the results of the numerical simulations, the acquirement of the new acknowledges of the reflections of the guided EM wave from the various boundaries, the construction of PML layers for FDTD simulations in rotational coordinates, the advances made in temporary excitation sources for FDTD and the formulation of the program code for FDTD in rotational coordinates in Matlab environment. The rightness of the numerical simulations was verified in practical experiments. The practical exploitation of the results is supposed in instrumentation and control technology - the level measurement in reservoirs.

This thesis describes the design, manufacture and characterisation of thick vacuum plasma sprayed tungsten (W) coatings on steel substrates. Fusion is a potentially clean, sustainable, energy source in which nuclear energy is generated via the release of internal energy from nuclei. In order to fuse nuclei the Coulomb barrier must be breached - requiring extreme temperatures or pressures – akin to creating a ‘star in a box’. Tungsten is a promising candidate material for future fusion reactors due to a high sputtering threshold and melting temperature. However, the large coefficient of thermal expansion mismatch with reactor structural steels such as the low activation steel Eurofer’97 is a major manufacturing and in-service problem. A vacuum plasma spraying approach for the manufacture of tungsten and tungsten/steel graded coatings has been developed successfully. The use of graded coatings and highly textured 3D interface surfi-sculpt substrates has been investigated to allow the deposition of thick plasma sprayed tungsten coatings on steel substrates. Finite element models have been developed to understand the residual stresses that develop in W/steel systems and made use of experimental measurements of coating thermal history during manufacture and elastic moduli measured by nano-indentation. For both the graded and surfi-sculpt coating, the models have been used to understand the mechanism of residual stress redistribution and relief in comparison with simple W on steel coatings, particularly by consideration of stored strain energy. In the case of surfi-sculpt W coatings, the patterned substrate gave rise to regular stress concentrating features, and allowed 2mm thick W coatings to be produced reproducibly without delamination. Preliminary through thickness residual stress measurements were compared to model predictions and provided tentative evidence of significant W coating stress relief by regulated coating segmentation.