Skin wound healing is an urgent problem in clinical treatment, in particular, with a military context. Although significant advances have been made in treating skin wounds, traditional methods face several challenges, e.g., limited donor skin tissue for transplants and inflammation over the period of long term healing. To address these challenges, in this study we present a method to fabricate Poly (ethylene-co-vinyl alcohol) (EVOH) nanofibres encapsulated with the Ag nanoparticle, using the electro-spinning technique. The manufacturing process of nanofibres by electro-spinning is the subject of the present research. Electro-spinning is a process which produces nanofibres through the electrically charged jet of a polymer solution. While the principle has long been understood, the process of forming them still remains difficult to control. In its simplest form, the technique consists of a pipette to hold the polymer solution, two electrodes and a DC voltage supply over a 10 KV range. The polymer dropping from the tip of the pipette is drawn into a jet which is electrically charged and spun into fine fibres by the electronic field. An appropriate combination of the control parameters, such as the charge voltage, density and viscosity of the polymer solution and the travel distance of the jet, etc. will lead to the production of fibres with diameters in the range of 10-7~8 meters. The fibres can then be collected on the surface of a grounded target. regulating three main parameters, namely, a concentrated EVOH solution, the electric voltage and the distance between the injection needle tip (high voltage point) and the fibre collector. Ag was added to the nanofibres to offer long term anti-inflammation properties by the slow release of Ag nanoparticles through the gradual degradation of the EVOH nanofibre. The method developed here could lead to new dressing materials for the treatment of skin wounds. The thin EVOH nanofibre sheets obtained from electro-spinning were tested in uniaxial tension for their mechanical properties, with a view to the possibilities of using them as wound dressings. It was found that the sheets show a mild hardening behaviour with extensive elongation and necking before failure in multiple fractures at random locations. The failure is not simply fibre breakage. Due to the random orientation of the continuing fibres in the sheet, detachment, shear, straightening and twinning. etc., among the fibres all occur at the same time to different extents. The Young’s modulus and the yield stress (at 0.4~0.5% proof strains) are predominately affected by the diameters of the fibres. The latter are largely insensitive to strain rate over the range tested.

Shear spinning of Haynes 282, Alloy 718, Alloy 600 and AISI 316L was done using several tool feeds and mandrel clearances. Multi passing of the materials was limited due to strain hardening and circumferential cracking except for AISI 316L. The effect of the tool feed and the mandrel clearance on the successful forming of the materials was established. The successfully spun samples were solution heat treated at varying temperatures and holding times to establish a range of grain sizes and hardness levels. An aging heat treatment process was performed for Haynes 282 and Alloy 718 to achieve precipitation strengthening. The micro hardness measurements were conducted for the materials prior to spinning and after spinning. The same was also done after the various heat treatment processes. Grain size mapping was conducted by the use of lineal intercept methods. Comparison of the results in terms of grain sizes and hardness values was done. The temperature ranges suitable for full recrystallization of the materials after the shear spinning were identified and the effect of the holding times on the grain growth established. Comparison with unspun samples showed that the heat treatment times required to achieve comparative hardness and grain sizes were distinctively different.

The development of cottons with improved fiber quality has been a major objective in breeding programs around the world. Breeders have focused their attention on improving fiber strength and length, and have generally not used fiber elongation in the selection process. Although literature has reported a negative correlation between fiber elongation and tenacity, this correlation is weak and should not prevent breeders from simultaneously improving fiber tenacity and fiber elongation. Furthermore, the work of rupture property, important in the spinning process, could be best enhanced by improving both fiber tenacity and fiber elongation. Fifteen populations were developed in 2007 by crossing good quality breeding lines with high elongation measurements to ‘FM 958’; a High Plains standard cultivar with good fiber quality but reduced elongation. Samples in every generation were ginned on a laboratory saw gin, and the lint was tested on HVI (High Volume Instrument). The F2 and F3 generations showed a wide range of variation for elongation (6.9% - 12.8% for the F2 and 4% - 9.20% for the F3) allowing divergent selection for low and high fiber elongation. A correlation (r) of -0.32 between strength and elongation was observed in the F2 individual plant selections. In the F3, the correlation (r) between strength and elongation was -0.36, and in the F4 the correlation (r) was -0.08. Nine lines were selected from the original 15 populations for spinning tests. The correlation between fiber elongation and strength for these lines was positive (r=0.424), indicating that with targeted selection, fiber elongation and strength can be simultaneously improved. Fiber elongation was positively correlated with yarn tensile properties tenacity (r=0.11), work-to-break (r=0.68) and breaking elongation (r=0.87); and was negatively correlated with yarn evenness properties, number of thin places (r=-0.16), number of thick places (r=-0.9), nep count (r=-0.24), hairiness (r=-0.38) and total number of imperfections (r=-0.38). All selections for high elongation were superior for all tensile properties compared to the low selections and the check in the analysis over locations and in each location. Furthermore, selections for high elongation were significantly different from the selections for low elongation and the check. In addition to developing lines for fiber spinning tests with improved, or differentiated, fiber elongation, this project was amended to evaluate and determine the heritability of fiber elongation. Three different methodologies were used to obtain estimates of heritability; variance components, parent off-spring regression, and realized heritability using F3, F4, and F5 generation. No inbreeding was assumed because there was no family structure in the generations within this study. Estimates of heritability by the variance component methods in the F3, F4 and F5 were 69.5%, 56.75% and 47.9% respectively; indicating that 40-50% of the variation was due to non-genetic effects. Parent off-spring regression estimates of heritability were 66.1% for the F3-4 and 62.8% for the F4-5; indicating a high resemblance from parents to off-spring. Estimates of realized heritability were obtained to determine the progress realized from selection for the low and high selection for fiber elongation. Estimates were intermediate (0.44–0.55), indicating moderately good progress from selection. The results from this project demonstrate that it is possible to improve fiber elongation and to break the negative correlation between elongation and strength. Furthermore, it has been demonstrated that improving fiber elongation results in the increase of length uniformity index and decreased short fiber content. Additionally, directed divergent selection was a successful methodology for the improvement of fiber elongation, and was useful to demonstrate that higher fiber elongation has a positive effect on yarn tensile properties, yarn evenness and processing. The development of new cultivars with improved fiber elongation will improve the quality and reputation of U. S.-grown cotton. The ultimate result will be better yarn quality and improved weaving efficiency, and particularly address current weaknesses in U. S. –grown cotton cultivars, especially from the High Plains of Texas, of more short fiber content, lower uniformity ratios, and weaker yarn strength.

Carbon allotropes have taken central stage of nanotechnology in the last two decades. Today, fullerenes, carbon nanotubes (CNTs), and graphene are essential building blocks for nanotechnology. Their superlative electrical, thermal and mechanical properties make them desirable for a number of technological applications ranging from lightweight strong materials to electrical wires and support for catalysts. However, transferring the exceptional single molecule properties into macroscopic objects has presented major challenges. This thesis demonstrates that carbon nanotubes and graphite dissolve in superacids and these solution can processed into macroscopic objects. Chapter 2 reviews neat CNT fiber literature. Specifically, the two main processing methods —solid– state and solution spinning — are discussed. CNT aspect ratio and fibers structure are identified as the main variables affecting fiber properties. Chapter 3 shows that graphite can be exfoliated into single-layer graphene by spontaneous dissolution in chlorosulfonic acid. The dissolution is general and can be applied to various forms of graphite, including graphene nanoribbons. Dilute solutions of graphene can be used to form transparent conductive films. At high concentration, graphene and graphene nanoribbons in chlorosulfonic acid forms a liquid crystal and can be spun directly into continuous fibers. Chapter 4 describes a solution–based method to form a thin CNT network. This network is an ideal specimen support for electron microscopy. Imaging nanoparticles with atomic resolution and sample preparation from reactive fluids demonstrate the unique feature of solution–based CNT support compared to state–of–the–art TEM supports . Chapter 5 describes CNT liquid crystalline phase. Specifically, CNT nematic droplets shape and merging dynamics are analyzed. Despite nanotube liquid crystals having been reported in various CNT systems, a number of anomalies such as low order parameter and spaghetti–like, nematic droplets are reported. However, CNTs in chlorosulfonic acid show elongated, bipolar droplets typical of other rod–like molecules. Moreover, their large aspect ratio allows capturing the transition from homogeneous to bipolar transition expected from scaling arguments.The equilibrium shape and merging dynamics demonstrate the liquid nature of CNT liquid crystals. Chapter 6 describes the CNT/chlorosulfonic acid fiber spinning. The influence of starting material, spinning dope concentration, spin draw ratio and coagulation on fiber properties is discussed. The linear scaling of fiber strength with CNT aspect ratio is demonstrated experimentally, once the best properties from different batches are compared. Moreover, Successful multi–hole spinning demonstrates the intrinsic scalability of wet spinning to meet the typical production output of industrial–scale spinning. Chapter 7 compares acid–spun CNT fibers to other CNTs fibers as well as existing engineered materials. Acid–spun CNT fibers combine the typical specific strength of high–strength carbon fibers to the thermal and electrical conductivity of metals. These properties are obtained because of a highly aligned, dense structure. The combined strength and electrical conductivity allow acid-spun fibers to be used as structural as well as conducting wire while the combined electrical and thermal properties allow for exceptional field emission properties. In conclusion, we demonstrate that multifunctional properties of carbon nanotubes that have fuelled much of the research in the past 20 years, can be attained on a macroscopic level via rational design of fluid–phase processing.

Att fördelarna med fysisk aktivitet är många är välkänt, ändå är uppemot 40% av befolkningen i Sverige fysiskt inaktiva. Vissa träningsformer är bättre och mer lockande än andra. Att träna i grupp antas skilja sig känslomässigt från att träna ensam. Syftet med studien var att undersöka nivåer och skillnader i ansträngnings och emotionsskattningar vid gruppträning jämfört med ensamträning. Sexton personer deltog med spinning som gruppträningsform och cykling på ett laboratorium som ensamträning i en inomindividsdesign där de samtidigt skattat ansträngning och sex känslotillstånd på Borg CR100 skalan. Resultatet visade att bara ett av sex känslotillstånd var signifikant högre efter spinning än laboratoriecykling. Skattningarna på skalan var mycket höga i absoluta tal, könsskillnaderna var små och spinningvana som bakgrundsfaktor tycks vara betydande. Resultaten var oväntade, även då fler känslotillstånd var nära att uppvisa signifikanta skillnader och att inte fler skillnader blev signifikanta förklaras genom metodbrister och för få deltagare i studien.

Polyethylene terephthalate is one of the most important engineering thermal plastics used for fibers, films and bottles. Despite its wide applications and vast global market, PET has shortcomings, which limits it usage in many areas. PET has a glass transition temperature (Tg) of 80 DEGREE Celsius, this temperature is too low for certain applications. Increase in glass transition temperature, high temperature mechanical properties, and dimensional stability is of great importance to further expand the applications of PET. Significant research efforts have been made toward this goal, using a variety of approaches. In this work, we attempt to improve the properties of PET melt spun filament. Three strategies has been investigated (i) copolymerization of more rigid comonomer, 4, 4' bibenzoate unit into the PET structure, (ii) UV crosslinking of functionalized PET fiber, and (iii) Reinforcing PET matrix with carbon nanofibers.

Spinning targets are usually observed in videos. The targets may sometimes appear as mobile targets at the same time. The targets become mobile spinning targets. Tracking a single point on a target is easier than tracking the whole target. We use a characteristic point on the target to estimate the interested parameters, such as angular velocity, virtual rotation center and moving velocity. Among these parameters, virtual rotation center does not spin, therefore it can be used to represent the position of the target. Traditionally, extended Kalman filter (EKF), unscented Kalman filter (UKF) and particle filter (PF) are choices for solving the nonlinear problems, but some problems exist. Linearization errors cause that EKF cannot accurately estimate the angular velocity. UKF and PF have high computational complexity. In the thesis, we give angular velocity an initial value. So we can establish a linear dynamic system model to displace the nonlinear model. Then, a new structure is proposed to avoid errors caused by initial value of angular velocity. In the structure, angular velocity is estimated individually and used to correct the initial value by feedback. We try to use fast Fourier transform to estimate angular velocity. But the convergence time of this method is affected by the value of angular velocity, and the direction of angular velocity can not be estimated directly. Therefore, Kalman filter (KF) with pseudo measurement is proposed to estimate the value of angular velocity. The estimator is accurate and has low computational complexity. Once angular velocity is estimated, we can easily predict the virtual rotation center from geometric relationship. In video system, measurements may be quantized and targets may sometimes be obstacled. We fix the measurement equation and use KF to mitigate quantization error. When measurements for the target is missing, the previous state is used to predict the current state. Finally, computer simulations are conducted to verify the effectiveless of the proposed method. The method can work in environments where measurement noise or quantization error exists. The methods can also be applied to different kinds of mobile spinning targets.

With the deregulation of power industry and the market competition, low cost, reliable power supply, and secured system operations are major concerns of the advanced deregulation markets. It is a natural extension to revise the objectives of the traditional optimal power flow (OPF) to help dispatch the power. Maximizing social welfare to create more values of the market is becoming an interesting topic. In the deregulation environment, a user-friendly mechanism is desirable to form an auction market information framework (AMIF) for power auction and market operation. This thesis proposed a prototype system to combine internet based technology, database system, and the auction market to construct an information framework of power auction market. The Internet technology used Dynamic HTML (DHTML) in WWW website to develop a convenient bidding environment for users. The database based on MS Access used open database connection (ODBC) technology to connect database and internet. The auction market integrates auction functions and re-designed OPF to support the auction mechanism and congestion management. This research could also provide a solid foundation for Taiwan¡¦s power system deregulation in the future. The proposed mechanism and its expansion could guarantee a smooth migration process and successful market/system operation.

Cell adhesion to extracellular matrices (ECM) is essential to numerous physiological and pathological processes. Cell adhesion is initiated by binding of the transmembrane integrin family of receptors to an ECM ligand such as fibronectin (FN). Once bound, integrins cluster together and form focal adhesions (FA). FAs serve as structural links and signal transduction elements between the cell and its extracellular environment. While a great deal of progress has been made in identifying the biochemical components that comprise focal adhesions and the roles they play in migration, cell spreading, and signaling, the contributions of these proteins to mechanical interactions between the cell and its environment remain poorly understood. A FA adhesion protein of particular importance is vinculin. When localized to focal adhesions, vinculin forms a ternary complex with talin and 1-integrin. This 1-integrin-talin-vinculin complex plays a central role in the regulation of FA assembly and cell spreading and migration. Nevertheless, the specific contribution to adhesive force generation of the 1-integrin-talin-vinculin complex remains poorly understood. The objective of this project was to analyze the role of vinculin in the cell adhesion strengthening process. Our central hypothesis is that vinculin modulates adhesion strength via regulating the size and/or composition of the integrin-talin-vinculin complex. We used a novel combination of biochemical reagents and engineering techniques along with quantitative and sensitive adhesion strength measurements to provide new insights into how the structure of vinculin contributes to cell adhesion strength.

Thesis (Ph. D.)--University of Texas at Austin, 2000. / Vita. Includes bibliographical references (leaves 286-299). Available also in a digital version from Dissertation Abstracts.