Electromagnetic effects of lightning currents during a direct hit to tall communication towers, other instrumented towers and chimneys can be hazardous to associated cables, as well as, electrical and electronics systems. The standard practice in telecommunication and other related fields is to bond the cable sheath to the tower and ground connection is made before it enters the base station. However, in some specific cases when power, signal and data logging cables are to be supported on the same tower, isolation of power cables is demanded. In a totally different situation, attempts are also made to have a dedicated isolated down conductor. A critical review of the situation demanded a more quantitative answer to the following questions: (i) whether it is possible to electrically isolate a dedicated down conductor, (ii) is it possible to electrically isolate the cables and their terminal equipment both mounted on towers serving as down conductor and if so, what will be the nature of current induced in the cables and (iii) as per the standard practice, if the cable sheaths are connected to the tower/structure, what will be the nature of the current shared by them. Addressing these important issues formed the scope of the present work. For the tall structures considered in this work, for the critical time periods, wave nature of the current dominates. This called for electromagnetic modeling covering Transverse Magnetic (TM) mode of the wave propagation. Owing to the complex geometrical features involved with the problem, both experiments on electromagnetically scaled laboratory models, as well as, theoretical simulation is attempted. An electromagnetically scaled laboratory model is employed for the time domain experimental investigation. This approach, which has been validated earlier, is further scrutinized to ensure its adequacy. In order to achieve generality and noting the fact that the associated parameters are rather difficult to be varied in the experimentation, theoretical investigation is also employed. For this, both NEC-2, as well as, an in-house thin wire time domain code developed for this work is employed. NEC-2 could handle multi-wire multi-radius junctions, while in-house time domain code could handle proximity and non-cylindrical shapes encountered with tower lattice elements. The investigation of induction to isolated cables on simple down conductors and towers is considered first. The induced current is shown to be bipolar oscillatory with the period of oscillation governed by the length of the cable. It is shown that the level of induction for good earth termination is below 5 – 10 % while that with moderate inductance in the earth termination can enhance the induction to higher levels. The level of induction is shown to be not critically dependent on the length of the cable, gap between cable and down conductor/tower. When multiple cables are mounted, they seem to influence each other and individually carry currents of lower amplitude. Also, the effect of shape and proximity of the tower lattice elements on induction is investigated. If the cable is housed inside a metallic tray, the amplitude of induced current is shown to be quite small. Subsequently, the evaluation of electrical stress between the isolated down conductor on tower and simplified representation of the structure is considered. A suitable definition of the electric stress for the wave regime is evolved and then it is shown that, at present, the voltage difference defined by the path integral of electric field across shortest path between the two entities is the best indicator for the stress. The electrical stress in the case of isolated down conductor on tower, as well as, down conductor with isolated cable is shown to reach very dangerous levels. On the other hand, the stress on the isolated cables on towers also serving as down conductors is shown to be relatively moderate. Interestingly, it is shown that the electrical stress and the voltage difference is dependent on the gap and for the critical time period, can be much lower than that calculated as a product of equivalent tower surge impedance and the stroke current, even before the arrival of ground end reflections. Finally, the current shared by cables connected to the down conductor is investigated. For the case of simple cylindrical down conductor with cable connected to it at the top, it is shown that the amount of current shared by the cable is not dependent on its length and the relative radii (cross section) have only a weak influence. For the case with down conductor formed by L and + angles, it is shown that the placement of cable at their interior corner can reduce the initial current shared by the cable. In order to model best possible situation with towers, experiments are conducted with cable inside an aluminum pipe. Even in this case, cable current builds up with successive reflections to become comparable with the current through the pipe itself. Subsequent investigation with 1:40 and 1:20 tower models lead to several interesting observations. Cables running along leg/face of the tower whether placed inside or outside the tower, always shares good amount of current. Further, frequent bonding of the sheath to the tower increases the current shared by the cable. Cable when housed in a metallic tray shares less than 50% of the current shared without the tray. Even though a complete quantification is not to be achieved in this work, it has made a good beginning with some significant contribution towards lightning protection issues pertaining to tall towers and structures.

In concentrated solar power (CSP) stations, large arrays of mirrors which are capable of changing its orientation are used to reflect the incident solar energy to a stationary receiver kept at a distance. Such mirrors are often called as heliostats. The receiver contains a heat absorbing medium like molten salt. By absorbing the thermal energy reflected from thousands of heliostats, the temperature would reach around 6000C and the heat can be used in thermal power plants to generate steam and thus run a turbine to produce electricity. One of the biggest advantages of CSP over conventional energy harvesting from Sun is that it can generate electricity during night for long hours of time from the thermal energy stored during daytime. This eliminates the usage of batteries or any other energy storing methods. The conversion efficiency is also high in CSP due to the high temperature achieved. With prior knowledge of the station coordinates, viz., the latitude and longitude, the day of the year and time, the direction or the path of sun can be fully determined. Typically, the sun's motion is tracked by the azimuth-elevation (Az-El) or the target-aligned configuration heliostats. In both these approaches, the mirror needs to be moved about two axes independently using two actuators in series with the mirror effectively mounted at a single point at the centre. This arrangement causes the mirror to deform in presence of gusty winds in a solar field which results in loss of pointing accuracy. Typically a beam error of less than 2-3 mrad is desirable in a large solar field and this value also includes other sources of loss of pointing accuracy like gravity and wind loading. In order to prevent this, a rigid support frame is required for each of the heliostats. In this work, two three degree-of-freedom parallel manipulators, viz., the 3-UPU wrist and 3-RPS, have been proposed to track the sun in central receiver systems. The main reasons for choosing a parallel manipulator as heliostat are its desirable characteristics like large load carrying capacity, high accuracy in positioning the mirror and easy to obtain the inverse kinematics and convenient for real time control. The proposed parallel manipulators support the load of the mirror, structure and wind loading at three points resulting in less deflection and thus a much larger mirror can be moved with the required tracking accuracy and without increasing the weight of the support structure. The algorithm for sun tracking is developed, extensive simulation study with respect to actuations required, variation of joint angles, spillage loss and leg intersection has been carried out. Using FEA, it is shown that for same sized mirror, wind loading of 22 m/s and maximum deflection requirement (2 mrad), the weight of the support structure is between 15% and 60% less with the parallel manipulators when compared to azimuth-elevation or the target-aligned configurations. A comprehensive study on stroke minimization of prismatic joints is carried out. It is found that a stroke of 700 mm is required for a 2 m x 2 m heliostat at Bangalore when the farthest heliostat is at a distance of 300 m from the tower. Although, there is an extra motor required to track the sun, the 3-RPS manipulator is better than the conventional methods if the mirror area per actuator criteria is taken into consideration. Prototypes of the Az-El and 3-RPS heliostats were made with a mirror size of 1 m x 1 m. A PID controller implemented using MATLAB-Simulink and a low cost, custom made motor driver circuit is used to control the motion of the 3-RPS heliostat. The algorithm developed is tested on the prototype by tracking a point marked on the wall of the lab space and is found to have a tracking error of only 7.1 mrad. Finally, the actual sun tracking is carried out on the roof of a building reflecting the sun-light to a wall situated 6.72 m above and a distance of 15.87 m from the heliostats. The images are captured at various instances of time from 11:30 a.m. to 3:30 p.m. on October 15th and November 10th, 2016, tracking errors are quantified and it is demonstrated that the proposed 3-RPS parallel manipulator can indeed work as a heliostat in concentrated solar power plants.

Anonymous Call Detail Records (CDR’s) from mobile phone towers provide a unique opportunity to aggregate individual location data to overall human mobility patterns. Flowminder uses this data to improve the welfare of low- and middle-income countries. The movement patterns are studied through key measurements of mobility. This thesis seeks to evaluate the estimates of key measurements obtained with mobile phone towers through simulation of continuous human movement on a linear network. Simulation is made with an agent based approach. Spatial point processes are used to distribute continuous start points of the agents on the linear network. The start point is then equipped with a mark, a path with an end point dependent on the start point. A path from the start point to the end point of an agent is modeled with a Markov Decision Process. The simulated human movement can then be captured with different types of mobile phone tower distributions realized from spatial point processes. The thesis will initially consider homogeneous Poisson and Simple Sequential Inhibition (SSI) processes on a plane and then introduce local clusters (heterogeneity) with Matérn Cluster and SSI processes. The goal of the thesis is to investigate the effects of change in mobile phone tower distribution and call frequency on the estimates of key measurements of mobility. The effects of call frequency are unclear and invite more detailed study. The results suggest that a decrease in the total number of towers generally worsens the estimates and that introducing local clusters also has a negative effect on the estimates. The presented methodology provides a flexible and new way to model continuous human movement along a linear network.

This thesis discusses the rise of the Republican party in Texas and specifically Harris County. The time period is the decade between the Presidential election of Dwight D. Eisenhower and the campaign of Jack Cox for Governor. Changes in the structure and leadership of the Republican party at the state level and specific precincts are examined in detail in chapter one. Leaders in Houston during this time period, such as Jesse Jones, Roy Cullen, and Oveta Culp Hobby are discussed in chapter two. The elections of Eisenhower, Cox, and Republican John Tower are analyzed in chapter three. The conclusion finds six major factors for the political changes occurring in Harris County, including economic and demographic changes. Main sources for this work included the Harris County Democratic party records and the Jack Cox Papers at the Center for American History, the Eisenhower Library, and the John Tower Papers.

[pt] Provamos que campos de vetores C1- genéricos em uma variedade compacta não possuem probabilidades invariantes absolutamente contínuas em relação a uma medida de volume. Este trabalho estende ao caso de tempo contínuo um resultado de Avila e Bochi. / [en] We prove that C1-generic vector fields in a compact manifold do not have absolutely continuous invariant probabilities. This extends a result of Avila and Bochi to the continuous time case.

The content of this work is the elaboration of a technology-oriented project for the construction of an apartment building with four above-ground floors in Blansko. This project includes a technical report, road mapping solutions, technological regulations, a drawing and technical report of the building site equipment, a timetable, a design of the machine assembly, control and test plans, a material resource assurance plan, and a technical report on health and safety at the building site.

The subject of this diploma thesis is design a cable-supported pedestrian bridge. Three different variants of the solution were created for the design. For detailed processing, variant no.2 was chosen - a suspended bridge with a pylon in the middle of the span. The main task is the static design of the supporting structure. The model for the lengthways is created in ANSYS. The SCIA engineer was used to solve crosswise. The assessment and dimensioning was done according to the limit state principles and valid standards.

The focus of this thesis is an architectural study of the Kraví Hora area in Brno in a 1:200 scale. The area is significant in both size and location, but has been underutilized up to this point. The objective of the thesis is to discover a solution acceptable for the city of Brno as well as BUT, whose intentions with the area differ significantly. The area has been designed to have recreational spaces of greenery. Traffic has been either largely reduced, or eliminated entirely. A wide variety of sports, eductational programs and recreational activities has been made available for visitors of all ages. The objective of the planned area is to inspire and positively motivate the study of technology and interest in science via its functional design. Exhibition areas, lecture halls, rentable workspaces for graduates, a recruitment center and general storage spaces has been designed in the area. The design of the buildings is based around the incline of the plot – they have a maximum of one extra floor over the level of the surrounding terrain. The green roof and the vertical outer layer of laminated timber is designed to provide a natural character to the structures. The predominantly horizontal area is granted an element of verticality in the form of a lookout tower.

The aim of master thesis was to create a program for the quantitative analysis of data backup schemes and with its help to identify and analyze the properties of commonly used schemes for different loads. Based on the obtained results, compile a set of principles for choosing the optimal data backup scheme. The program was created by Matlab. It can be used to find out parameters for individual backup schemes: Parameters C (total backup volume) and E (medium volume of recovery backups), backups size of individual days, workload of individual storages, cost of storages and cost of overall backup scheme, size the total amount of data written per storage per time slot. At the end of the thesis is defined a scheme for choosing the optimal backup scheme.

The object of this thesis is to implement the contruction of the apartment block in Prague's area Suchdol. This report contains the technical report for construction technological project, technical report of site facilities, technological regulation, budget, time management, project of machinery assembly, inspection and test plan, environmental plan, occupational safety, study of main technological stages and comparative study.