Thesis (Ph. D.)--University of Washington, 2006. / Vita. Includes bibliographical references (leaves 204-217).

Das Ziel dieser Arbeit ist die Untersuchung der aktiven Komponenten und ihrer Wechselwirkungen in teilorganischen Hybrid-Solarzellen. Diese bestehen aus einer dünnen Titandioxidschicht, kombiniert mit einer dünnen Polymerschicht. Die Effizienz der Hybrid-Solarzellen wird durch die Lichtabsorption im Polymer, die Dissoziation der gebildeten Exzitonen an der aktiven Grenzfläche zwischen TiO2 und Polymer, sowie durch Generation und Extraktion freier Ladungsträger bestimmt. Zur Optimierung der Solarzellen wurden grundlegende physikalische Wechselwirkungen zwischen den verwendeten Materialen sowie der Einfluss verschiedener Herstellungsparameter untersucht. Unter anderem wurden Fragen zum optimalen Materialeinsatz und Präparationsbedingungen beantwortet sowie grundlegende Einflüsse wie Schichtmorphologie und Polymerinfiltration näher betrachtet. Zunächst wurde aus unterschiedlich hergestelltem Titandioxid (Akzeptor-Schicht) eine Auswahl für den Einsatz in Hybrid-Solarzellen getroffen. Kriterium war hierbei die unterschiedliche Morphologie aufgrund der Oberflächenbeschaffenheit, der Film-Struktur, der Kristallinität und die daraus resultierenden Solarzelleneigenschaften. Für die anschließenden Untersuchungen wurden mesoporöse TiO2–Filme aus einer neuen Nanopartikel-Synthese, welche es erlaubt, kristalline Partikel schon während der Synthese herzustellen, als Elektronenakzeptor und konjugierte Polymere auf Poly(p-Phenylen-Vinylen) (PPV)- bzw. Thiophenbasis als Donatormaterial verwendet. Bei der thermischen Behandlung der TiO2-Schichten erfolgt eine temperaturabhängige Änderung der Morphologie, jedoch nicht der Kristallstruktur. Die Auswirkungen auf die Solarzelleneigenschaften wurden dokumentiert und diskutiert. Um die Vorteile der Nanopartikel-Synthese, die Bildung kristalliner TiO2-Partikel bei tiefen Temperaturen, nutzen zu können, wurden erste Versuche zur UV-Vernetzung durchgeführt. Neben der Beschaffenheit der Oxidschicht wurde auch der Einfluss der Polymermorphologie, bedingt durch Lösungsmittelvariation und Tempertemperatur, untersucht. Hierbei konnte gezeigt werden, dass u.a. die Viskosität der Polymerlösung die Infiltration in die TiO2-Schicht und dadurch die Effizienz der Solarzelle beeinflusst. Ein weiterer Ansatz zur Erhöhung der Effizienz ist die Entwicklung neuer lochleitender Polymere, welche möglichst über einen weiten spektralen Bereich Licht absorbieren und an die Bandlücke des TiO2 angepasst sind. Hierzu wurden einige neuartige Konzepte, z.B. die Kombination von Thiophen- und Phenyl-Einheiten näher untersucht. Auch wurde die Sensibilisierung der Titandioxidschicht in Anlehnung an die höheren Effizienzen der Farbstoffzellen in Betracht gezogen. Zusammenfassend konnten im Rahmen dieser Arbeit wichtige Einflussparameter auf die Funktion hybrider Solarzellen identifiziert und z.T. näher diskutiert werden. Für einige limitierende Faktoren wurden Konzepte zur Verbesserung bzw. Vermeidung vorgestellt. / The main objective of this thesis is to study the active components and their interactions in so called organic hybrid solar cells. These consist of a thin inorganic titanium dioxide layer, combined with a polymer layer. In general, the efficiency of these hybrid solar cells is determined by the light absorption in the donor polymer, the dissociation of excitons at the heterojunction between TiO2 and polymer, as well as the generation and extraction of free charge carriers. To optimize the solar cells, the physical interactions between the materials are modified and the influences of various preparation parameters are systematically investigated. Among others, important findings regarding the optimal use of materials and preparation conditions as well as detailed investigations of fundamental factors such as film morphology and polymer infiltration are presented in more detail. First, a variety of titanium dioxide layer were produced, from which a selection for use in hybrid solar cells was made. The obtained films show differences in surface structure, film morphology and crystallinity, depending on the way how the TiO2 layer has been prepared. All these properties of the TiO2 films may strongly affect the performance of the hybrid solar cells, by influencing e.g. the exciton diffusion length, the efficiency of exciton dissociation at the hybrid interface, and the carrier transport properties. Detailed investigations were made for mesoporous TiO2 layer following a new nanoparticle synthesis route, which allows to produce crystalline particles during the synthesis. As donor component, conjugated polymers, either derivatives of cyclohexylamino-poly(p-phenylene vinylene) (PPV) or a thiophene are used. The preparation routine also includes a thermal treatment of the TiO2 layers, revealing a temperature-dependent change in morphology, but not of the crystal structure. The effects on the solar cell properties have been documented and discussed. To take advantage of the nanoparticle synthesis, the formation of crystalline TiO2 particles by UV crosslinking and first solar cell measurements are presented. In addition to the nature of the TiO2 layer, the influence of polymer morphology is investigated. Different morphologies are realized by solvent variation and thermal annealing. It is shown that, among other factors, the viscosity of the polymer solution and the infiltration into the TiO2 layer mainly affects the efficiency of the solar cell. Another approach to increase the efficiency is the development of new hole-conducting polymers that absorb over a wide spectral range and which are adjusted to the energy levels of TiO2. Also new concepts, for example, the combination of thiophene- and phenyl-units into a copolymer are investigated in more detail. In summary, important parameters influencing the properties of hybrid solar cells are identified and discussed in more detail. For some limiting factors concepts to overcome these limitations are presented.

<p>An electrolytic cell was designed and constructed for the preparation of TiO2 nanotubes. Conditions of anodic oxidation were established to reproducibly prepare TiO2 nanotubes of average length 35-50 &mu / m vertically orientated relative to the plain of a pure titanium metal sheet. A non-aqueous solution of ethylene glycol containing small percentage of ammonium fluoride was used as the electrolyte with an applied voltage of 60 V. The morphology and dimensions of the nanotube arrays were studied by scanning (SEM) and transmission (TEM) electron microscopy. The effect of calcination under different conditions of temperature and atmosphere (nitrogen, argon and air) were assessed by both X-ray diffraction (XRD) and cyclic voltammetry (CV). Cyclic voltammetry studies were made possible by construction of a specially designed titanium electrode upon which the nanotubes were prepared. CV studies established a positive correlation between crystallinity and conductivity of the nanotubes. Doping of the nanotubes with nitrogen and carbon was established by elemental analysis, X-ray photoelectron spectroscopy (XPS) and Rutherford back scattering (RBS). The effect of nonmetal doping on the band gap of the TiO2 nanotubes was investigated by diffuse reflectance spectroscopy (DRS).</p>

In today’s society there is an increasing need for energy, an increase which for the most part is supplied by the use of fossil fuels. Fossil fuel resources are limited and their use has harmful effects on the environment, therefore the development of technologies that produce clean energy sources is very appealing. Natural photosynthesis is capable of converting solar energy into chemical energy through a series of efficient energy and electron transfer reactions with water as the only electron source. Thus, constructing an artificial system that uses the same principles to convert sunlight into electricity or storable fuels like hydrogen is one of the major forces driving artificial photosynthesis research. This thesis describes supramolecular complexes with the intention of mimicking the electron transfer reactions of the donor side in Photosystem II, where a manganese cluster together with a tyrosine catalyses the oxidation of water. All complexes are based on Ru(II)-trisbipyridine as a photosensitizer that is covalently linked to electron donors like tyrosine or manganese. Photochemical reactions are studied with time-resolved transient absorption and emission measurements. Electrochemical techniques are used to study the electrochemical behavior, and different photoelectrochemical techniques are used to investigate the complexes adsorbed onto titanium dioxide surfaces. In all complexes, intramolecular electron transfer occurs from the linked donor to photo-oxidized Ru(III). It is also observed that coordinated Mn(II) quenches the excited state of Ru(II), a reaction that is found to be distance dependent. However, by modifying one of the complexes, its excited state properties can be tuned in a way that decreases the quenching and keeps the electron transfer properties. The obtained results are of significance for the development of multinuclear Ru-Mn complexes that are capable of multi-electron transfer.

In this study nanocrystalline TiO2 was synthesized by a sol-gel process. The effect of praseodymium (Pr) doping and calcination conditions on the textural properties of nano structured particles and photocatalytic activity were examined. Samples were synthesized by hydrolyzation of titanium tetra iso-propoxide (TTIP) and calcination at different temperatures. Characterizations of the samples were carried out using XRD, BET, XPS, TEM, and EDAX analyses. It was observed that anatase to rutile transformation is favored by higher calcination temperatures. The XRD analysis indicated that the anatase structure is stabilized by Pr doping and rutile phase formation at higher calcination temperatures is inhibited by the addition of Pr. It was also observed that Pr doping enhances the surface area and inhibit crystal growth. Phase stabilization effect of Pr doping was also confirmed by XPS results. EDAX analysis revealed that Pr is dispersed atomically in the crystal structure. The Photoluminescence analysis by 325 nm excitation indicated the emissions at 608 and 621 nm which can be attributed by photon up-conversion. The photocatalytic activities of the samples were measured by methylene blue degradation and phenol mineralization reactions. The photocatalytic activities of the Pr doped samples were also found higher than undoped TiO2 samples.

A real-time, mobile Scanning Electrical Mobility Spectrometer (SEMS) was designed using a Condensation Particle Counter (CPC) and Differential Mobility Analyzer (DMA) to measure the size distribution of nanoparticles. The SEMS was calibrated using monodisperse Polystyrene Latex (PSL) particles, and was then applied to study the size distribution of TiO2 nanoparticle aerosols generated by spray drying water suspensions of the nanoparticles. The nanoparticle aerosol size distribution, the effect of surfactant, and the effect of residual solvent droplets were determined. The SEMS system was designed by integrating the Electrical System, the Fluid Flow System, and the SEMS Software. It was calibrated using aerosolized Polystyrene Latex (PSL) spheres with nominal diameters of 99 nm and 204 nm. TiO2 nanoparticle aerosols were generated by atomizing water suspensions of TiO2 nanoparticles using a Collison nebulizer. Size distribution of the TiO2 aerosol was measured by the SEMS, as well as by TEM. Furthermore, the effect of surfactant, Tween 20 at four different concentrations between 0.01mM and 0.80mM, and stability of aerosol concentration with time were studied. It was hypothesized that residual particles in DI water observed during the calibration process were a mixture of impurities in water and unevaporated droplets. Solid impurities were captured on TEM grids using a point-to-plane Electrostatic Precipitator (ESP) and analyzed by Energy Dispersive Spectroscopy (EDS) while the contribution of unevaporated liquid droplets to residual particles was confirmed by size distribution measurements of aerosolized DI water in different humidity conditions. The calibration indicated that the mode diameter was found to be at 92.5nm by TEM and 95.8nm by the SEMS for 99nm nominal diameter particles, a difference of 3.6%. Similarly, the mode diameter for 204nm nominal diameter particles was found to be 194.9nm by TEM and 191nm by SEMS, a difference of 2.0%. Measurements by SEMS for TiO2 aerosol generated by Collison nebulizer indicated the mode diameters of 3mM, 6mM, and 9mM concentrations of TiO2 suspension to be 197.5nm, 200.0nm and 195.2nm respectively. On the other hand, the mode diameter was found to be approximately 95nm from TEM analysis of TiO2 powder. Additionally, concentration of particles generated decreased with time. Dynamic Light Scattering (DLS) measurements indicated agglomeration of particles in the suspension. Furthermore, the emulation of single particle distribution was not possible even after using Tween 20 in concentrations between 0.01mM and 0.80mM. From the study of residual particles in DI water, it was found that residual particles observed during the aerosolization of suspensions of DI water were composed of impurities present in DI water and unevaporated droplets of DI water. Although it was possible to observe solid residual particles on the TEM grid, EDS was not able to determine the chemical composition of these particles.

A titanium dioxide powder co-doped with boron and zirconium was prepared by mechanical ball milling. Photocatalytic performance of the powder was evaluated by degradation of methylene blue (MB) solution under UV illumination. XRD patterns were refined by Rietveld analysis method to obtain accurate lattice parameters and position of the atoms in the crystal structure of TiO2. XRD analysis indicated that the B and/or Zr doped TiO2 powders composed of anatase and did not exhibit any additional phase. Rietveld analysis suggested that dopant B and Zr elements were successfully weaved into crystal structure and distorted the lattice of TiO2. The highest distortion was obtained by co-doping. SEM investigations confirmed that mechanical ball milling technique led to a decrease in particle size of TiO2 powder. XPS analysis revealed that dopant B and Zr atoms did not appear in any form of compound including Ti and O elements. Results of photocatalytic activity test suggested that boron and zirconium co-doped TiO2 particles exhibited a better visible light response and photocatalytic activity than that of mono element doped TiO2 (i.e. B-TiO2 and Zr-TiO2) and undoped TiO2 particles. A 20% improvement in photocatalytic activity of reference TiO2 powder (powder ball milled without dopant addition) was achieved by B and Zr co-doping. The enhanced photocatalytic activity is attributed to synergistic effects of B-Zr co-doping the lattice of TiO2 as well as particle size reduction.

Chemical-looping combustion is an indirect oxygen combustion strategy, considered to be the most cost-effective power generation technology with the CO2 inherently concentrated. In this process, a solid oxygen carrier is used to transfer oxygen from the air reactor to the fuel reactor, which completely isolates nitrogen in air to meet with fuels. The oxygen carriers in the combustion process are subjected to the severe environments, such as high temperatures, multi-cycle operations, and thermodynamic limitations. Thus, the preparation of an oxygen carrier with high durability and better kinetics under harsh environment could be an essential part of Chemical-looping combustion development. In this study, modified wet impregnation and co-precipitation methods have been developed. The active ingredient is copper(II) oxide, and the supporting material is either directly from titanium(IV) oxide (anatase 99%) or that prepared from other titanium resources such as titanium tetrachloride and tetrabutyl titanate. Preliminary results showed the prepared oxygen carriers functioned properly in the multi-cycles of oxidization and reduction in TGA at different temperatures. Characterization of used oxygen carriers was carried out using techniques of XRD, and SEM-EDS, which provide information for the difference between oxygen carriers from different preparation methods. Through the comparison, the oxygen carrier from the sol-gel preparation method has better dispersion and oxidation activity than those from mechanical mixing, wet-impregnation, and cox precipitation method. Moreover, towards the oxygen carrier from sol-gel method, nucleation model and diffusion models were determined at different reaction periods.

An investigation of surface structures formed on polycrystalline and single crystal TiO2 (titania) samples having under gone various heat treatments in a controlled hydrogen bearing atmosphere was conducted. The study included the recreation and examination of the process discovered by Sehoon Yoo at Ohio State University to form nanofibers on the surface of polycrystalline TiO2 disks. Fibers were formed by heating samples to 700??in a 5%H2 95%N2 gas stream. The nanofibers formed during this processes are approximately 5-20 nanometers in diameter and can be 100??f nanometers long. The fibers do not actually grow on the surface, but are what remain of the surface as the material around them is removed by the gas stream V i.e., nanocarving. The mechanism of fiber formation and the effect of varying experimental parameters remained unknown and were explored within this study. This included changing gas composition, flow rate, and changes in sample preparation. The effect of isovalent doping and impurities within the starting powder were examined. Sintering temperature and time was investigated to determine the effect of grain size and surface morphologies prior to nanocarving. The effect of elevated temperature and 5%H2 95%N gas on the surface of TiO2 single-crystal wafers was also investigated. Test methods include Thermogravimetric Analysis (TGA), Mass Spectrometry (MS), Scanning Electron Microscopy (SEM), and X-ray diffraction (XRD) analysis.

In this study, the characteristics of Nickel-doped LPD-TiO2 films on silicon substrate were investigated. In our experiment, we do some measurement about physical, chemical and electrical properties for undoped and Nickel-doped LPD-TiO2 films and discussed with them. The TiO2 film thickness was characterized by field emission scanning electron microscopy ( FE-SEM ), structure was characterized by X-ray diffraction (XRD), chemical properties was characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR) and electrical properties was characterized by leakage current: current-voltage (B1500A) and dielectric constant: capacitance-voltage (4980A). For the electrical property improvements, we investigated the Ni-doped LPD-TiO2 films by the post-anneal treatments in nitrogen, oxygen and nitrous oxide ambient. For nickel doping, the nickel chloride was used as the doping solution and the electrical characteristics were improved. After thermal annealing in nitrous oxide at 700 oC, the dielectric constant of polycrystalline titanium oxide film is 29 and can be improved to 94 with nickel doping.