<p>An electrolytic cell was designed and constructed for the preparation of TiO2 nanotubes. Conditions of anodic oxidation were established to reproducibly prepare TiO2 nanotubes of average length 35-50 &mu / m vertically orientated relative to the plain of a pure titanium metal sheet. A non-aqueous solution of ethylene glycol containing small percentage of ammonium fluoride was used as the electrolyte with an applied voltage of 60 V. The morphology and dimensions of the nanotube arrays were studied by scanning (SEM) and transmission (TEM) electron microscopy. The effect of calcination under different conditions of temperature and atmosphere (nitrogen, argon and air) were assessed by both X-ray diffraction (XRD) and cyclic voltammetry (CV). Cyclic voltammetry studies were made possible by construction of a specially designed titanium electrode upon which the nanotubes were prepared. CV studies established a positive correlation between crystallinity and conductivity of the nanotubes. Doping of the nanotubes with nitrogen and carbon was established by elemental analysis, X-ray photoelectron spectroscopy (XPS) and Rutherford back scattering (RBS). The effect of nonmetal doping on the band gap of the TiO2 nanotubes was investigated by diffuse reflectance spectroscopy (DRS).</p>

Titano dioksidas, pasižymintis unikaliomis fizikinėmis bei cheminėmis savybėmis, yra gerai žinoma, plačiai naudojama bei tyrinėjama medžiaga. Tiriant TiO2 elektrines savybes, galima gauti informacijos, kokios naujos medžiagos fazės formuojasi plonasluoksnėse dangose. Elektrinė titano dioksido varža priklauso nuo bandinio stechiometriškumo, nusakančio vyraujančius defektus bei laidumo tipą. Siekiant gauti norimų savybių plonasluoksnes dangas, būtina atsižvelgti į bandinių paruošimo ir gamybos procesus. Bandinių nusodinimui naudojama vakuuminė užnešimo technika leidžia kontroliuoti procesus, lemiančius dangos savybes. Šiame darbe buvo atliekama literatūros analizė apie elektrines TiO2 savybes bei įvairių faktorių įtaką šio parametro kitimui. Taip pat atkreiptas dėmesys į plonasluoksnių struktūrų nusodinimą, naudojant fizikinį dangų nusodinimą iš garų fazės (PVD). Paviršinės TiO2 varžos tyrimas buvo atliekamas panaudojant 4 zondų metodą. / Titanium dioxide is well known, widely used and investigated material that shows unique physical and chemical properties. Investigations of TiO2 electrical conductivity gives an information about the new phases formed in thin films. Surface resistance of titanium dioxide depends on sample‘s stoichiometry and it shows predominant defects and type of conductivity being in the thin film structure. It is very important to pay an attention into processes of sample‘s preparation and formation technique in order to get thin films with desirable properties. Thin films were formed using vacuum deposition technique. There has been done a scientific literature survey in order to know the main factors that causes changes of TiO2 electrical properties in this work. An attention was paid into deposition of thin film structures using physical vapor deposition (PVD) technique as well. Measurements of TiO2 surface resistance were done using four probe method.

Pollution created by textile dyeing operations attracts significant attention because an effluent containing a complex mixture of coloured and potentially toxic compounds can be released with the discharged water. Developing dyes and dyeing conditions to reduce the amount of residual dye contained in any effluent has been one of many approaches to minimise this environmental impact. However, the presence of coloured discharge cannot be totally eliminated using only this strategy. Thus, development of efficient post-dyeing wastewater treatment methods capable of removing coloured products from the water is of paramount importance. TiO2-mediated photocatalytic degradation of organic dye molecules via oxidation is the focus of the study reported in this thesis. TiO₂ significantly increases the rate of photodegradation of a wide range of organic dyes under mild operating conditions, and is able to mineralise a wide spectrum of organic contaminants. TiO₂ is also one of the very few substances appropriate for the industrial applications. One of primary aims of this thesis is to test the hypothesis that augmenting standard TiO₂ photocatalysts with Au nanoparticles could increase performance of a catalyst, while immobilizing TiO₂ on SiO₂ support may improve the cost of the process efficiency, i.e. more photocatalytic degradation per particle of TiO₂. Combining TiO₂ doped with gold nanoparticles on SiO₂ support has the potential to provide the highest photocatalytic ability at the lowest cost. The first half of the thesis is concerned with establishing and optimizing experimental conditions for monitoring photodegradation via UV-Visible spectroscopy. Effects of various conditions such as temperature, sequence of addition of reagents, exposure to light vs. experiments in dark, sampling methods, and the use of quenching agent were examined. The main conclusions from this study are that light-induced photodegradation using titanium dioxide nanoparticles catalysts is comparatively more efficient than purely chemical catalytic (e.g. non-light mediated) degradation, even if the latter is performed at elevated temperature. Further, the rate of dye degradation is affected considerably by the parameters of the system. The degradation rate depends strongly on the pH of the solution, due to charges on both the catalyst surface and in the dye. In general, at pH ≤ 6.8, which is the zero charge point for TiO₂, reactions proceeded faster than those at higher pH. Six dyes from four different classes of dyes used in industry were used in this study, and all showed different photodegradation behaviour. The second half of thesis tests the photocatalytic abilities of various TiO₂-based catalysts: pure TiO₂ (commercial and custom-made in our laboratory), TiO₂-supported gold nanoparticles (Au/TiO₂), SiO₂-supported TiO₂ (TiO₂/SiO₂), and SiO₂-supported Au/TiO₂. The best photocatalytic performance was observed for the custom-made TiO₂ code-named as e-TiO₂, which was synthesized using the sol-gel method in dry ethanol. TiO₂-supported Au55 nanoparticles showed a similar level of catalytic ability but are significantly more expensive. It was observed that dye adsorption played a significant role in the case of SiO₂-immobilized photocatalysts.

An examination of the possibility of applying pulse pressure metalorganic chemical vapour deposition (PP-MOCVD) to conformal coating and an investigation of PP-MOCVD processing parameters were undertaken using the deposition of thin, conformal titanium dioxide (TiO₂) on 3-D featured and non-featured substrates. The characterisation of the conformality and wettability analysis of thin TiO₂ was carried out using titanium tetraisopropoxide (TTIP) dissolved in toluene as a precursor and featured silicon (Si) and silicon nitride (Si₃N₄) as substrates. The features on the substrates were in micro- and nano-scale with the aspect ratio up to 2:1. The processing parameters investigated were temperatures between 400 and 600°C, reactor base pressures from 50 to 200 Pa, injection volumes between 50 and 250 µl, precursor concentrations in the range of 0.15 to 0.50 mol% and pulsing times from 10 to 20 sec. The surface morphology and thickness were examined using a scanning electron microscope (SEM). The composition of the films was qualitatively identified by energy dispersive X-ray spectroscopy (EDS). X-ray diffraction (XRD) and Raman spectroscopy were used to analyse the phase and grain size. The surface roughness and grain size were evaluated using atomic force microscopy (AFM). The optical properties were characterised using UV-VIS light spectroscopy. The anti-sticking characteristic was examined by wettability analysis, measuring the contact angle of the film with water. The research examined the relationships between processing parameters and growth rate, conformality, surface roughness, grain size, phase and water contact angle. A new measurement for thin film conformality was derived based on a statistical analysis of a large number of film thickness measurements on a fracture surface over the lithographed features. The best conformality of 0.95 was obtained for micro-scale features at the lowest temperature in the range of investigation, 400℃, with pulse exposure characterised by a base pressure of 100 Pa, TTIP concentration of 0.50 mol%, injection volume of 50 µl and pulsing time of 10 sec. Conformality for micro-scale features was in the range of 0.82 to 0.97 over a wide range of deposition temperatures. Conformality was as low as 0.45 over nano-scale structures at the higher exposure rate. The conformality decreased as the temperature and precursor concentration increased. The precursor injection volume was found to have minor influences on conformality. The growth rate increased as the temperature increased and reached the maximum at the deposition temperature of 450℃ with the precursor concentration of 0.50 mol% and injection volume of 100 µl. The base pressure and relaxation time had slight influences on the growth rate over the deposition temperature range of 400 to 500℃. The growth rate was increased as the precursor concentration and precursor injection volume increased. The deposited TiO₂ films exhibited columnar growth and anatase phase. The base pressure and pulsing time had no obvious effects on grain size and surface roughness. The grain size decreased as the deposition temperature increased. The surface roughness increased as the deposition temperature increased. Contact angles of over 100° were found with conformality of over 0.80. The variation in contact angle was related to the surface morphology of the deposited films. The contact angle increased as the grain size decreased. High wettability was found for films in the mid-range of pulse exposure, in this study at pulse exposure of 53, or at high deposition temperature, in this case at 600°C. The as-deposited TiO₂ thin films were hydrophobic depending on the surface morphology, surface roughness and grain size.

Nanoparticles, i.e. particles with at least one dimension smaller than 100 nm, are present in large quantities in ambient air and can also be found in an increasing amount of consumer products. It is known that many nanomaterials have physicochemical properties that differ from physicochemical properties of the same material in bulk size. It is therefore important to characterize nanoparticles and to evaluate their toxicity. To understand mechanisms behind nanotoxicity, it is important to study the uptake of nanoparticles, and how they are accumulated. For these purposes model studies of cellular uptake are useful. In this thesis metal oxide and carbon-based nanoparticles have been studied in living cells using Raman spectroscopy. Raman spectroscopy is a method that facilitates a non-destructive analysis without using any fluorescent labels, or any other specific sample preparation. It is possible to collect Raman images, i.e. images where each pixel corresponds to a Raman spectrum, and to use the spectral information to detect nanoparticles, and to identify organelles in cells. In this thesis the question whether or not nanoparticles can enter the cell nucleus of lung epithelial cells has been addressed using hyperspectral analysis. It is shown that titanium dioxide nanoparticles and iron oxide nanoparticles are taken up by cells, and also in the cell nucleus. In contrast, graphene oxide nanoparticles are mainly found attached on the outside of the cell membrane and very few nanoparticles are found in the cell, and none have been detected in the nucleus. It is concluded that graphene oxide nanoparticles are not cytotoxic. However, a comparison of Raman spectra of biomolecules in cells exposed to graphene oxide, unexposed cells and apoptotic cells, shows that the graphene oxide nanoparticles do affect lipid and protein structures. In this thesis, several multivariate data analysis methods have been used to analyze Raman spectra and Raman images. In addition, super-resolution algorithms, which originally have been developed to improve the resolution in photographic images, were optimized and applied to Raman images of cells exposed to submicron polystyrene particles in living cells.

Increasing energy demands as well as the depletion of traditional energy sources has led to the need for the development and improvement of energy conversion and storage technologies. Concerns regarding climate change and environmental awareness has also created increased support for renewable energy and clean technology research. One technology of interest is the photocatalyst, which is a material that is able to use natural light irradiation to create electrical currents or drive useful chemical reactions. For this purpose, a strong photocatalytic material has the following properties: i) strong absorbance over a wide solar radiation spectrum; ii) high surface area for adsorbance of target species; iii) high electron efficiency characteristics such as high conductivity, long charge-carrier lifetimes, and direct pathways for electron transport; and iv) good chemical stability. All of these requirements serve to maximize the efficiency and overall output of the device, and are a means of overcoming the performance hurdle required for the commercialization of various energy conversion technologies. Unfortunately, current photocatalytic materials suffer from small absorbance windows and high recombination rates which greatly reduce the conversion efficiency of the catalyst. Titanium dioxide (TiO2), the most well-known and widely used photocatalyst, can only absorb light within the ultraviolet (UV) range – which accounts for only a small fraction of the entire solar spectrum. For this reason, the majority of recent research has been directed toward producing photocatalysts that are able to absorb light within the visible and infrared range in order to maximize the amount of light absorbed in the solar spectrum. Other research is also being conducted to increase electrical conductivity and charge-carrier separation to further increase conversion efficiency. It is hoped that these two major problems surrounding photocatalysis can be solved by using novel functional nanomaterials. Nanomaterials can be synthesized using three main techniques: crystal structuring, doping, and heterostructuring. By controlling the structure of the crystal, materials of different phase, morphology, and exposed crystal facets can be synthesized. These are important for controlling the electronic properties and surface reactivity of the photocatalyst. Doping is the act of introducing impurities into a material in order to modify its band structure and create a red shift in light absorption. Lastly, heterostructuring is a method used to combine different photocatalysts or introduce co-catalysts in order to widen the range of absorption, encourage charge separation, or both. Many novel photocatalytic materials have been synthesized using these techniques. However, the next-generation photocatalytic material has remained elusive due to the high cost of production and complexity of synthesis. This thesis proposes a novel photocatalytic material that can be used in photocatalyzed waste-water remediation. Graphene-wrapped hierarchical TiO2 nanoflowers (G-TiO2) are synthesized using a facile synthesis method. TiO2 is a material of particular interest due to its chemical and photo-corrosion stability, high redox potential, strong electronic properties, and relative non-toxicity. Hierarchical structures are highly desired because they are able to achieve both high surface area and high conductivities. Graphene hybridization is a popular method for creating composites with highly conductive networks and highly adsorptive surfaces. To the best of my knowledge, the hybridization of graphene on hierarchical TiO2 structures without pre-functionalization of TiO2 has not yet been demonstrated in literature. Therefore, it is proposed that the use of such a material would greatly simplify the synthesis process and enhance the overall photocatalytic performance of TiO2 over that of commercial TiO2 photocatalysts. In the first study, hierarchical TiO2 nanoflowers are synthesized using a solvothermal reaction. It is then shown that under UV irradiation, the hierarchical TiO2 material is able to outperform commercial TiO2 material in the photodegradation of methylene blue (MB). Further characterization shows that this improvement is explained by a higher electrical conductivity, and exists in spite of having a lower specific surface area compared to the commercial material. In the second study, G-TiO2 is synthesized by mixing hierarchical TiO2 nanoflowers with graphene oxide (GO) and reducing GO in a hydrothermal reaction. Photocatalytic tests show that this hybridization further improves the performance of the hierarchical TiO2. Further studies reveal that an optimal graphene loading of 5 wt% is desired in order to achieve the higher rate of MB decomposition, and greatly outperforms P25 in this task. Characterization shows that G-TiO2 composites have increased specific surface area and electrical conductivity compared to the hierarchical TiO2 nanoflower. It is believed that this work will provide a simple and efficient avenue for synthesizing graphene–TiO2 composites with greatly improved photocatalytic activity. This work may also find use in other photocatalytic applications such as chemical deconstruction and manufacturing, hydrogen production, solar cells, and solar enhanced fuel cells.

The shaping of functional materials and the control of their texture at all length scales are sine qua non conditions for the improvement of current systems. This PhD project consists in creating complex solid architectures using interdisciplinary methods such as sol-gel chemistry or complex fluids physics. Therefore, it is possible to synthesize Titanium Dioxide macroscopic fibers or films which possess a hierarchical porosity. This organization allows the optimization of the matter transport (liquid/gaz) for air depollution application (photocatalysis) or dye-sensitized solar cells. In another project, we were able to control the alignment of zinc oxide nanorods within a macroscopic fiber. This alignment provides to the fiber an anisotropic photoluminescence behavior which can be useful for switching devices application. Finally, we synthesized anisotropic particles and nano-sheets of polypyrrole (conducting polymer) in order to obtain smooth thin films presenting interesting electrical properties. The objective was to use them as electrolyte and/or electrode in dye-sensitized solar cells.

Thesis (PhD)--University of South Australia, 2001.

The present project has made a comprehensive assessment of the effect of Nb doping on various charge-transfer related properties of TiO2. Of particular focus, the electrical properties of Nb-doped TiO2 (0.65 at %) have been investigated using the simultaneous measurement of electrical conductivity and thermoelectric power. This investigation was undertaken at elevated temperatures (1073 K -- 1298 K) in equilibrium with a gas phase of controlled oxygen activity (10-10 Pa < p(O2) < 75 kPa). In addition, the effect of segregation on the surface versus bulk composition of Nb-doped TiO2 was also investigated at a function of temperature and oxygen activity. Specifically, the following determinations were undertaken: The effect of oxygen activity, p(O2) and temperature on both electrical conductivity and thermoelectric power The effect of Nb on the defect disorder and related electrical properties of TiO2 The determination of equilibration kinetics and the associated chemical diffusion data for Nb-doped TiO2 The determination of Nb bulk diffusion in TiO2 The effect of p(O2), temperature and dopant content on Nb segregation and the related surface composition of Nb-doped TiO2 The obtained electrical properties enable the determination of a defect disorder model for Nb-doped TiO2, which may be considered within the following p(O2) regimes: Strongly Reduced Regime. In this regime, the predominant ionic defect was anticipated to be oxygen vacancies compensated electronically by electrons. While the transition to this regime (from higher p(O2)) was clearly observed, the predominant defect disorder existing beyond this transition was not confirmed due to an inability to obtain sufficiently low oxygen activity. Metallic-type conductivity behaviour was observed within this transition region. Reduced Regime I. In this regime, the predominate defect disorder defined by the electronic compensation of incorporated Nb ions by electrons was clearly observed. Reduced Regime II. In this regime, the predominate defect disorder defined by the ionic compensation of incorporated Nb ions by quadruply-charged titanium vacancies, was clearly observed. The present project included the determination of diffusion data which included: Temperature dependence of 93Nb tracer diffusion in single crystal TiO2 over the temperature range 1073 K -- 1573 K Chemical diffusion coefficient over the temperature range 1073 K -- 1298 K and oxygen activity range, 10-10 Pa < p(O2) < 75 kPa These pioneering studies are significant as they enable the prediction of the processing conditions required to reliably 1) incorporate Nb into the TiO2 lattice, and 2) achieve equilibrium with the gas phase. Finally, the present project included investigations on the effect of Nb segregation on the surface composition of Nb-doped TiO2, with the following outcomes: Due to segregation, the surface can be significantly enriched in Nb compared to the bulk The extent of enrichment increases as the bulk Nb content or the oxygen activity is decreased Following enrichment, the surface Nb concentration could be sufficiently high to assume a unique surface phase The outcomes of the present project are significant as they can enable the processing of TiO2 with enhanced charge transport and controlled surface properties.

Titanium dioxide, TiO2, has potential applications as a photoelectrode for photoelectrochemical generation of hydrogen by splitting water using solar energy and as a photocatalyst for water purification. This study is part of the UNSW research program to process TiO2-based oxide semiconductors as high-performance photoelectrodes and photocatalysts. This study investigates the effect of defect disorder on semiconducting properties of polycrystalline TiO2. This study involved the processing of high-purity polycrystalline TiO2 and determination of its semiconducting properties through measurement of electrical conductivity and thermoelectric power at elevated temperatures (1073-1323K) in controlled oxygen activities [1x10-13 Pa < p(O2) < 75 kPa]. The study included two types of experiments: Determination of electrical properties under conditions of gas/solid equilibrium. The data obtained was used to derive defect disorder and related semiconducting properties Monitoring of electrical properties during equilibration. This data was used to determine the chemical diffusion coefficient. The data obtained under equilibrium conditions indicates that oxygen may be used as a dopant to impose controlled semiconducting properties. In reduced conditions TiO2 is an n-type semiconductor and under oxidizing conditions TiO2 is a p-type semiconductor. The n-type behaviour is associated with oxygen vacancies as the predominant defects and titanium interstitials as the minority defects. The p-type behaviour is closely related to titanium vacancies that are formed during prolonged oxidation. Charge transport at elevated temperature was shown to involve substantial contribution from ions. Analysis of electrical properties enabled determination of several defect-related quantities including the activation enthalpy for oxygen vacancy formation, and the activation energy of the electrical conductivity components related to electrons, holes and ions. The kinetic data obtained during gas/solid equilibration enabled determination of the chemical diffusion coefficient which exhibited a complex dependence on nonstoichiometry. In addition, prolonged oxidation showed that equilibration occurred in two kinetic regimes. One for highly mobile oxygen vacancies and titanium interstitials which quickly reached an ??operational equilibrium?? within hours and another slow kinetic regime for equilibration of titanium vacancies over many thousand hours. The determined chemical diffusion coefficient data may be used to select the processing conditions required to impose uniform concentration of defects within a TiO2.