This master‘s thesis deals with design and realisation of a control module for automated measurements of the modern contactless inductive position sensors by a mechanical rotational system consisting of a DC motor and an incremental quadrature encoder. The thesis presents methods of driving DC motor and recording of measured data by a microcontroller. The thesis presents a communication protocol between the control module and personal computer via USB interface. A part of this thesis is also to develop a control software and firmware, including the measurement and evaluation of properties of the control module.

An IoT device measuring soil moisture to help a municipality improve the work surrounding irrigation is deployed for testing and used by the concerned municipal workers. The IoT device is an initial prototype using Pycom’s LoPy4 with expansion board 3.1 and 3xAAA batteries as power supply. The prototype is not suitable for larger-scale testing due to the size, cost, and power consumption. This thesis focuses on decreasing the cost and size while increasing the battery life for the IoT device.The IoT device is communicating using the LoRaWAN protocol. For the device to be as energy-efficient as possible, the LoRa and LoRaWAN protocol are explored to use all possibilities to save energy. Active time and power consumption between different spreading factors are examined and discussed for power consumption and range concerns. The prototype produced by the work performed in this thesis is used to measure soil moisture. The microcontrollers selected and tested will not restrict to that purpose. The microcontrollers can integrate with many kinds of sensors. Integration with other types of sensors is under future work in this thesis. The integration possibilities making the thesis relevant for anyone with an intermediate knowledge inprogramming wanting to get introduced into the IoT development cycle, develop aLoRa node, and learning how to use the LoRaWAN stack with MicroPython.

Automatisering av testprocesser är viktigt eftersom manuella tester är komplicerade och tidskrävande. Testarbetet effektiviseras och kvaliteten kan höjas genom att automatisera testprocesserna. Arbetet som beskrivs i det här examensarbetet har utförts på Phoniro AB i Halmstad och syftet med projektet är att identifiera och konstruera en helautomatiserad lösning för skanningen av NFC-taggar och QR-koder. I arbetet konstrueras en mekanisk testrigg som är en lämplig lösning baserat på framtagna krav. För att välja den mest lämpliga mjukvaru- och hårdvaruplattformen för testriggen utifrån kraven användes utvärderingsmatriser. Testriggen består av tre delar, en 3D-modell av testriggen, ett kretskort som är testriggens kontroller och mjukvarudel för att programmera testriggen och integrera den med företagets testramverk. Därefter har testriggen byggts upp, alla delar kopplats ihop och programmerats för att testas mot de krav som ställts upp. Testriggen som har tagits fram är en prototyp som har en stor utvecklingspotential med tanke på framtida utveckling / Automation of test processes is essential because manual tests are complicated and time-consuming. Automating the test processes makes the test work more efficient and increases quality. The work described in this diploma thesis was performed at Phoniro AB in Halmstad, and the purpose of the project is to identify and construct a fully automated solution for the scanning of NFC tags and QR codes. The report describes a design that meets the requirements and needs established for the development models used in the project. A mechanical test rig was constructed as a suitable solution, based on developed requirements during the project. Evaluation matrices were used to select the most suitable software and hardware platforms for the test rig based on the project needs. The test rig consists of a 3D-model, a circuit board, and a software component to program the test rig and integrate it with Phoniro’s test framework. The test rig developed is a prototype with excellent potential for future development.

This Master thesis deals with the design and construction of a measuring device for measuring and the current consumption logging of sensors using LPWAN (Low Power Wide Area Network) technology. The theoretical part of the thesis firstly summarizes selected LPWAN technologies. Selected technologies, namely: LoRaWAN, Sigfox and Narrowband IoT (NB-IoT), are described more in detail. Further, the current measurement techniques are briefly discussed. The main focus is given to the current shunt measuring methods. The second half of thesis describes procedures conducted during the design and construction of a measuring device. The current measuring is based on the current shunt circuit complemented by the voltage amplification circuit, whose output is subsquently converted into digital form using an AD converter. The thesis describes in great detail the procedures for selecting individual components and important processes used in design of printed circuit boards. An integral part of the measuring device implementation is the design and implementation of control software, which is described in detail and supplemented by workflow charts underlining the entire description. The implementation of the entire measuring device is completed by the design and implementation of the cover box using 3D printing technology. Finally, the specifications of designed device are briefly discussed based on the limits of the used components.

This thesis is concerned with the measurement of physical quantities. Thesis describes sensors in general terms and requirements, which delivers latest trends in the field of automation. The main theme of this thesis is sensors for meassuring pressure, and their connection to the automation chain. In the next part thesis describes the design of the converter for connecting SMART sensors for pressure measuring, that use HART communication protocol, to the automation systems managed by a communication protocol IO-link. First will be described in detail various communication standards by their ISO OSI model, and on this theoretical basis will be based design of converter between communication protocol HART and communication protocol IO-Link. The last part will be Designed software for this converter.

Master’s thesis deals with design of laboratory supply with precise voltage and current measuring. At the beginning it presents properties, advantages and disadvantages of linear and switching supplies, based on these facts it chooses a linear type of regulator. The design continues with detailed description of power and control analog and digital circuits. The thesis includes description of taking control over the supply from the front panel or through computer. The last part is devoted to measurement results and to presentation of some static and dynamic parameters of the designed supply.