A technique for wall compensation in the ultra-wideband (UWB) through-wall imaging radar is presented. The UWB system can be utilize in high precision measurements, but due to phase distortion and amplitude attenuation caused by the wall the precision is limited, the target is displaced, and the image is defocused.  In order to mitigate the wall effects, two methods are applied in this project. First, the unknown wall transfer function is estimated using real data measurements to design the inverse filter. Secondly, FIR Wiener filter is designed to improve the received m-sequence. After all, each method is tested using three parameters, the signal to noise ratio (SNR), the signal to clutter ratio (SCR), and the relative position error (RPE).  The inverse filter can eliminate the wall effects very well; it could correct not only the position of the target but also the image defocus. The new method can give improve the image quality and that can extend the use of UWB radar in many applications.

No / The design of a physically small, equal phase and equal power, 1-to-4 ultra-wideband Wilkinson power divider is presented. Initially, a 1-to-2 divider was designed and optimized for the 3.1 GHz-to-10.6 GHz range. The 1-to-4 divider was then realized using three 1-to-2 dividers, and further optimized for full band insertion loss, return loss, and isolation. The circuits were constructed using a 0.75 mm thick Rogers RO3035 substrate, and experimentally validated.

Made available in DSpace on 2014-12-17T14:55:37Z (GMT). No. of bitstreams: 1 AntonioSA.pdf: 2010232 bytes, checksum: 027e876fa92242a6ba0e73009f5debd5 (MD5) Previous issue date: 2009-08-11 / This work is the analysis of a structure of the microstrip antenna designed for application in ultra wide band systems (Ultra Wideband - UWB). This is a prospective analytical study where they tested the changes in the geometry of the antenna, observing their suitability to the proposed objectives. It is known that the UWB antenna must operate in a range of at least 500 MHz, and answer a fractional bandwidth greater than or equal to 25%. It is also desirable that the antenna meets the specifications of track determined by FCC - Federal Communication Commission, which regulates the system in 2002 designating the UWB bandwidth of 7.5 GHz, a range that varies from 3.1 GHz to 10, 6 GHz. by setting the maximum power spectral density of operation in -41.3 dB / MHz, and defining the fractional bandwidth by 20%. The study starts of a structure of geometry in the form of stylized @, which evolves through changes in its form, in simulated commercial software CST MICROWAVE STUDIO, version 5.3.1, and then tested using the ANSOFT HFSS, version 9. These variations, based on observations of publications available from literature referring to the microstrip monopole planar antennas. As a result it is proposed an antenna, called Monopole Antenna Planar Spiral Almost Rectangular for applications in UWB systems - AMQEUWB, which presents simulated and measured results satisfactory, consistent with the objectives of the study. Some proposals for future work are mentioned / Este trabalho consiste na an?lise de uma estrutura de antena de microfita projetada para aplica??o em sistemas de banda ultra larga (ultra wideband UWB). Trata-se de um estudo prospectivo e anal?tico onde s?o experimentadas as modifica??es na geometria da antena, observando-se sua adequa??o aos objetivos propostos. Sabe-se que a antena UWB deve operar numa faixa de no m?nimo 500 MHz, e atender uma banda fracion?ria maior ou igual a 25%. ? desej?vel ainda, que a antena atenda ?s especifica??es de faixa determinadas pela FCC Federal Communication Commission, que em 2002 regulamentou o sistema UWB designando a largura de banda de 7,5 GHz, numa faixa que varia de 3,1 GHz a 10,6 GHz. fixando a densidade espectral de pot?ncia m?xima de opera??o em -41,3 dBm/MHz, e definindo a banda fracion?ria em 20%. O estudo parte de uma estrutura de geometria em forma de @ estilizada, que evolui atrav?s de modifica??es na sua forma, simuladas nos softwares comerciais CST MICROWAVE STUDIO, vers?o 5.3.1, e, em seguida, testado com o uso do ANSOFT HFSS, vers?o 9. Varia??es estas, com base em observa??es de publica??es dispon?veis na literatura, referentes a antenas de microfita monopolo planar. Como resultado ? proposta uma antena, denominada Antena Monopolo Quase-Espiral Planar Retangular para aplica??es em sistemas UWB AMQEUWB, que apresenta resultados simulados e medidos satisfat?rios, coerente com os objetivos do estudo. Algumas propostas para trabalhos futuros est?o citadas

Ultra-wideband (UWB) technology and its use in imaging and sensing have drawnsignicant interest in the last two decades. Extensive studies have contributed toutilize UWB transient scattering for automated target recognition and imagingpurposes. In this thesis a near-eld UWB synthetic aperture radar (SAR) imagingalgorithm is presented.It is shown with measurements and simulation, that it is possible to reconstruct an imageof an object in the near eld region using UWB technology and SAR imaging algorithm.However the nal SAR image is highly aected by unwanted scattered elds at each pixelusually observed as an image artifact in the nal image. In this study these artifactsare seen as a smile around the main object. Two methods are suggested in this thesiswork to suppress this artifact. The rst method combines the scattered eld informationreceived from both rear and front of the object to reconstruct two separate images, onefrom rear view and one from front view of the object respectively. Since the scatteredelds from behind the object are mirrored, the pixel by pixel multiplication of thesetwo images for objects with simple geometry will cancel the artifact. This method isvery simple and fast applicable to objects with simple geometry. However this methodcannot be used for objects with rather complex geometry and boundaries. Thereforethe Range Point Migration (RPM) method is used along with the global characteristicsof the observed range map to introduce a new artifact rejection method based on thedirectional of arrival (DOA) of scattered elds at each pixel. DOA information can beused to calculate an optimum theta for each antenna. This optimum angle along withthe real physical direction of arrival at each position can produce a weighting factor thatlater can be used to suppress the eect of undesired scattered elds producing the smileshaped artifact. Final results of this study clearly show that the UWB SAR accompaniedwith DOA can produce an image of an object free of undesired artifact from scatteredeld of adjacent antennas.

In this thesis, a low-profile, high-gain, ultra-wideband (UWB) planar dipole antenna is presented for radar imaging applications. The antenna is loaded with open complementary double concentric split-hexagonal-ring resonators (LC tank) and chip resistors, and backed with a novel double-layer FSS reflector for gain enhancement. A broadband microstrip to parallel-plate transformer is designed as the feeding structure of the antenna to provide impedance matching and balanced-to-unbalanced transition. The measurement results show the proposed antenna operates over the frequency bandwidth of 0.65-3.8 GHz with S11< -10 dB (VSWR) and smooth gains in the range of 6.2-9 dBi.

Generation of high-peak power, microwave ultra-short pulses (USPs) is desirable for ultra-wideband communications and remote sensing. A variety of microwave USP generators exist today, or are described in the literature, and have benefits and limitations depending on application. A new class of pulse compressors for generating USPs using electromagnetic time reversal (TR) techniques have been developed in the last decade, and are the topic of this dissertation. This dissertation presents a compact TR microwave pulse-compression cavity that has ultra-wide bandwidth (5 GHz – 18 GHz), and employs waveguide feeds for high-peak power output over the entire band. The system uses a time-reversal-based pulse compression scheme with one-bit processing (OBTR) to achieve high compression gain. Results from full-wave simulations are presented as well as measurements showing compression gain exceeding 21.2 dB, 22% efficiency, and measured instantaneous peak output powers reaching 39.2 kW. These are all record results for this type of pulse compressor. Additionally presented is new analysis of variation in compression gain due to impulse response recording time and bandwidth variation, new experimental work on the effect of mode stirrer position on compression gain, and a novel RF switch-based technique for reducing time-sidelobes while using OBTR. Finally, a new technique is presented that uses a reverberant cavity with only one feed connected to an ultra-wideband circulator (6.5 GHz to 17 GHz) to perform TRPC. Prior to this work, TRPC has only been demonstrated in electromagnetics using two or more feeds and a reverberant cavity acting as the time-reversal mirror. This new 1-port technique is demonstrated in both simulation and measurement. The proposed system achieves up to a measured 3 dB increase in compression gain and increased efficiency. Also, a novel application of the random coupling model (RCM) to calculate compression gain is presented. The cavity eigenfrequencies are modeled after eigenvalues of random matrices satisfying the Gaussian orthogonal ensembles (GOE) condition. Cavity transfer functions are generated using Monte Carlo simulations, and used to compute the compression gains for many different cavity realizations. / Doctor of Philosophy / Generation of high-peak power, microwave ultra-short pulses (USPs) is desirable for ultra-wideband communications and remote sensing. A variety of microwave USP generators exist today, or are described in the literature, and have benefits and limitations depending on application. A new class of pulse compressors for generating USPs using electromagnetic time reversal (TR) techniques have been developed in the last decade, and are the topic of this dissertation. This dissertation presents a compact TR-based microwave pulse-compression cavity that has unique features that make it optimal for high-power operations, with results from simulations as well as measurements showing improved performance over other similar cavities published in the literature with a record demonstrated peak output power of 39.2 kW. Additionally, new analysis on the operation and optimization of this cavity for increased performance is also presented. Finally, a new technique is presented that uses a cavity with only one feed that acts as both the input and output. This 1-port technique is demonstrated in both simulation and measurement. The proposed system achieves a two-times increase in compression gain over its 2-port counterpart. In conjunction with these measurements and simulations, a novel technique for predicting the performance of these cavities using Monte Carlo simulation is also presented.

yes / A novel miniaturized planar double inverted-F antenna is presented. The antenna design is based on the electromagnetic coupling of two air dielectric PIFA antennas, combined with a broadband rectangular plate feed structure to achieve ultra-wideband characteristics. The computed and experimental impedance bandwidths show good agreement over an UWB frequency band from 3.1 GHz to 10.6 GHz for |S11| < -10dB. The antenna is electrically small, with size 0.31 x 0.16 x 0.09 wavelengths at 3.1 GHz and 1.06 x 0.55 x 0.31 wavelengths at 10.6 GHz. The simulated and measured gain and radiation patterns show acceptable agreement and confirm that the antenna has appropriate characteristics for short range wireless applications. / MSCRC

Les travaux présentés lors de cette thèse s’inscrivent dans le cadre des réseaux de microsystèmes communicants dont les réseaux de capteurs sont l’exemple le plus connu. La problématique adressée est la conception d’une interface radio communicante répondant aux besoins spécifiques des microsystèmes communicants : simplicité, faible coût, faible consommation, faible encombrement, haut débit et reconfigurabilité. Les technologies actuelles sans fil comme le WiFi, le Bluetooth, et Zigbee ne sont pas en mesure de répondre à ces contraintes spécifiques. L’étude se focalise sur la technologie IR-UWB (Impulse Radio Ultra-WideBand). Dans un premier temps, une étude conjointe sur la capacité du canal et l’implémentation matérielle est menée pour déterminer l’architecture optimale des émetteurs-récepteurs en IR-UWB. Cette étude propose l’utilisation d’une architecture multi bandes IR-UWB (MB-IR-UWB) à implémentation mixte à 60 GHz avec des antennes directives. Cette solution est optimisée sur les critères de débit et puissance consommée. Afin de supporter l’ensemble des besoins des applications des réseaux de microsystèmes communicants et l’évolution de l’environnement d’opération, la reconfigurabilité doit être implémentée dans les émetteur-récepteurs proposés. Ces travaux présentent une proposition de reconfigurabilité par paramètres, qui permet de supporter la plus grande gamme de reconfigurabilités multi propriétés (débit, taux d’erreur, portée, puissance consommée, …) de l’état de l’art. Enfin, pour valider par la mesure les travaux sur la reconfigurabilité et sur les architectures d’émetteur-récepteurs IR-UWB, des implémentations FPGA et ASIC sont réalisées. Un nouveau procédé de synchronisation et démodulation conjointe reconfigurable est proposé dans le récepteur IR-UWB BPSK S-Rake. Les mesures montrent que le circuit de traitement proposé améliore les performances en synchronisation, démodulation, efficacité, débit du réseau, consommation et complexité du circuit. L’émetteur-récepteur IR-UWB reconfigurable proposé atteint un débit et une gamme de reconfigurabilité supérieure à l’état de l’art. / The research work presented in this thesis is situated in the framework of wireless sensor networks (WSNs). The issue addressed is the design of a radio interface answering the specific needs of WSNs: simplicity, low cost, low power, small size, high data rate and reconfigurability. Current wireless technologies like WiFi, Bluetooth, and Zigbee are not able to respond to these requirements. Thus this study focuses on Impulse Radio Ultra-WideBand (IR-UWB) technology. At first, a joint study of the channel capacity and the hardware implementation is carried out to determine the optimal architecture of IR-UWB transceivers. This study proposes an architecture using multi-band IR-UWB (MB-UWB-IR) with a mixed implementation at 60 GHz with directional antennas. This solution is optimized according to the criteria of data rate and power consumption. To support the all the needs of WSN applications and to adapt to the evolution of the WSN’s environment, reconfigurability must be implemented in the proposed IR-UWB transceiver. This thesis presents a new solution: the reconfigurability by parameters. It supports the widest range of multi-property reconfigurability (with respect to data rate, bit error rate, radio range, power consumption, ...) of the state of the art. Finally, to validate these techniques by measurements, FPGA and ASIC implementations are realized by using the reconfigurability and the IR-UWB transceiver architecture proposed. A new method for joint synchronization and demodulation is proposed for a reconfigurable IR-UWB BPSK S-Rake receiver. The measurements show that the proposed technique improves the circuit performance: synchronization, demodulation, efficiency, network throughput, power consumption and complexity of the circuit. The proposed IR-UWB reconfigurable transceiver achieves a data rate and a wider range of reconfigurability compared to the state of the art

La réglementation mondiale, pour des appareils de courte portée, permet l’utilisation sans licence de plusieurs Gigahertz de bande autour de 60 GHz. La bande des 60 GHz répond aux besoins des applications telles que les réseaux de capteurs très haut débit autonome en énergie,ou les transmissions à plusieurs Gbit/s avec des contraintes de consommation d’énergie. Il y a encore peu de temps, les interfaces radios fonctionnant dans la bande millimétrique n’étaient réalisables qu’en utilisant des technologies III-V couteuses. Aujourd’hui, les avancées des technologies CMOS nanométriques permettent la conception et la production en masse des circuits intégrées radiofréquences (RFIC) à faible coût.Cette thèse s’inscrit dans des travaux de recherches dédiés à la réalisation d’un système dans un boîtier (SiP, System in Package) à 60 GHz contenant à la fois l’interface radio (bande de base et circuits RF) ainsi qu’un réseau d’antennes. La première partie de cette thèse est dédiée la conception de la tête RF de l’émetteur-récepteur à faible consommation pour l’interface radio. Les blocs clefs de cette tête RF (amplificateurs, mélangeurs et un oscillateur commandé en tension) sont conçus, réalisés et mesurés en utilisant la technologie CMOS 65 nm de ST Microelectronics. Des éléments actifs et passifs sont développés spécifiquement pour l’utilisation au sein de ces blocs. Une étape importante vers l’intégration de la tête RF complète de l’émetteur-récepteur est l’assemblage de ces blocs de base afin de réaliser une puce émetteur et une puce récepteur. A ce but, une tête RF pour le récepteur a été réalisée. Ce circuit présent une consommation et un encombrement plus réduit que l’état de l’art.La deuxième partie de cette thèse présente le développement des modèles comportementaux des blocs de base conçus. Ces modèles au niveau système sont nécessaires afin de simuler le comportement du SIP, qui devient trop complexe si des modèles détaillés du niveau circuitsont utilisés. Dans cette thèse, une nouvelle technique modélisant le comportement en régime transitoire et régime permanent ainsi que le bruit de phase des oscillateurs commandés en tension est proposée. Ce modèle est implémenté dans le langage de description de matérielVHDL-AMS. La technique proposée utilise des réseaux de neurones artificiels pour approximer la caractéristique non linéaire du circuit. La dynamique est décrite dans l’espace d’état. Grâce à ce modèle, il est possible de réduire d’une façon drastique le temps de calcul des simulations système tout en conservant une excellente précision / Worldwide regulations for short range communication devices allow the unlicensed use of several Gigahertz of bandwidth in the frequency band around 60GHz. This 60GHz band is ideally suited for applications like very high data rate, energy-autonomous wireless sensor networks or Gbit/s multimedia links with low power constraints. Not long ago, radio interfaces that operate in the millimeter-wave frequency range could only be realized using expensive compound semiconductor technologies. Today, the latest sub-micron CMOS technologies can be used to design 60GHz radio frequency integrated circuits (RFICs)at very low cost in mass production. This thesis is part of an effort to realize a low power System in Package (SiP) including both the radio interface (with baseband and RF circuitry) and an antenna array to directly transmit and receive a 60GHz signal. The first part of this thesis deals with the design of the low power RF transceiver front-end for the radio interface. The key building blocks of this RF front-end (amplifiers, mixers and a voltage controlled oscillator (VCO)) are designed, realized and measured using the 65nm CMOS technology of ST Microelectronics. Full custom active and passive devices are developed for the use within these building blocks. An important step towards the full integration of the RF transceiver front-end is the assembly of these building blocks to form basic transmitter and receiver chips. Circuits with small chip size and low power consumption compared to the state of the art have been accomplished.The second part of this thesis concerns the development of behavioral models for the designed building blocks. These system level models are necessary to simulate the behavior of the entire SiP, which becomes too complex when using detailed circuit level models. In particular, a novel technique to model the transient, steady state and phase noise behavior of the VCO in the hardware description language VHDL-AMS is proposed and implemented. The model uses a state space description to describe the dynamic behavior of the VCO. Its nonlinearity is approximated by artificial neural networks. A drastic reduction of simulation time with respect to the circuit level model has been achieved, while at the same time maintaining a very high level of accuracy

La technologie Ultra WideBand (UWB) sur fibre est une solution prometteuse pour répondre aux enjeux des futurs réseaux de communication WLAN/WPAN. Les caractéristiques de la fibre, incluant son énorme bande passante, offrent la possibilité d'une bonne qualité de service à longue portée. La propagation sans-fil UWB doit être réalisée sous des contraintes de densité spectrale de puissance particulières, imposées par l'autorité de régulation (FCC pour les Etats-Unis). La nouveauté de notre travail provient de I' exploitation des avantages d'un amplificateur optique à semi-conducteurs (SOA) afin d'obtenir une extension de portée à un coût et une complexité limités. Cependant, les effets non linéaires et le bruit d'émission spontanée amplifiée (ASE), intrinsèques à ce type de composant, sont susceptibles de dégrader la performance du système. La réduction de ces effets indésirables a donc été d'une importance centrale dans cette étude. Les non-linéarités du SOA ont été compensées en appliquant une solution de pré-distorsion analogique des formes d'ondes électriques. Un traitement basé sur phaser a également été proposé pour réduire simultanément I' influence de I'ASE et linéariser les caractéristiques du SOA, grâce à des opérations de chirping réparties entre l'émetteur et le récepteur. Avec la transmission Impulse Radio, en raison des propriétés temporelles des formats de modulation, des raies spectrales apparaissent, ce qui peut violer la limite FCC ou réduire I' efficacité énergétique. Une nouvelle technique de randomisation de formes d'ondes a été étudiée, qui s'est révélée efficace pour supprimer ces pics spectraux. Les trois approches ont montré un grand potentiel avec les formats On Off Keying et Pulse Position Modulation, à longue portée optique. Les performances d'une modulation différentielle Chaos Shift Keying ont finalement été examinées; une probabilité d'erreur inférieure a été obtenue expérimentalement en comparaison avec d'autres modulations non cohérentes. / Ultra WideBand (UWB) over fiber is a promising technology for meeting the demands of future wireless local-area networks (WLANs) and wireless personal-area networks (WPANs). Thanks to the enormous bandwidth and fiber characteristics, a high communication quality may be established at long reach. UWB wireless propagation must be achieved with special power and spectral constraints fixed by the regulatory bodies (e.g. US Federal Communication Commission). The novelty of our work originates from exploiting the benefits of a Semiconductor Optical Amplifier (SOA) so as to get a reach extension at limited cost and complexity. However, the inherent nonlinear effects and Amplified Spontaneous Emission (ASE) noise associated to such device may affect the system performance.Overcoming these impairments has been of central importance in this study. SOA nonlinearities have been mitigated by applying analog pre-distortion in electrical domain. Phaser-based processing was also proposed to simultaneously reduce ASE influence and linearize SOA characteristics, thanks to up/down chirping performed on the transmitter/receiver sides. With Impulse Radio UWB transmission, due to the time properties of modulation patterns, discrete lines arise in the corresponding spectrum, which may violate FCC limit or reduce the power efficiency. A new shape randomization technique has been investigated, which proved to be effective in suppressing these spectral spikes. The three approaches have shown a great potential with On Off Keying and Pulse Position Modulation formats at long optical reach.The performance of Differential Chaos Shift Keying was finally examined in the over fiber system, a lower error probability was experimentally achieved in comparison with other non-coherent modulations.