We present a method of performing precision landings of a vertical take-off and landing (VTOL) unmanned air vehicle (UAV) with the use of an onboard vision sensor and information about the aircraft's orientation and altitude above ground level (AGL). A method for calculating the 3-dimensional location of the UAV relative to a ground target of interest is presented as well as a navigational controller to position the UAV above the target. A method is also presented to prevent the UAV from moving in a way that will cause the ground target of interest to go out of view of the UAV's onboard camera. These methods are tested in simulation and in hardware and resulting data is shown. Hardware flight testing yielded an average position estimation error of 22 centimeters. The method presented is capable of performing precision landings of VTOL UAV's with submeter accuracy.

The purpose of the study was to evaluate the merits of the DiscRotor concept that combine the features of a retractable rotor system for vertical take-off and landing (VTOL) with an integral, circular wing for high-speed flight. Tests were conducted to generate basic aerodynamic characteristics of the DiscRotor in hover and in fixed-wing flight. To assess the DiscRotor during hover, small scale tests were conducted on a 3ft diameter rotor without the presence of a fuselage. A "hover rig" was constructed capable of rotating the model rotor at speeds up to 3,500 RPM to reach tip speeds of 500fps. Thrust and torque generated by the rotating model were measured via a two-component load cell, and time averaged values were obtained for various speeds and pitch angles. It has been shown that the DiscRotor will perform well in hover. Ground Effects in hover were examined by simulating the ground with a movable, solid wall. The thrust was found to increase by 50% compared to the ground-independent case. Pressure distributions were measured on the ground and disc surfaces. Velocity measurements examined the flow field downstream of the rotor by traversing a seven hole velocity probe. A wake behind the rotor was shown to contract due to a low pressure region that develops downstream of the disc. Wind tunnel experimentation was also performed to examine the fixed wing flight of the DiscRotor. These experiments were performed in the VA Tech 6â X6â Stability Tunnel. A model of the fuselage and a circular wing was fabricated based upon an initial sizing study completed by our partners at Boeing. Forces were directly measured via a six degree of freedom load cell, or balance, for free stream velocities up to 200fps. Reynolds numbers of 2 and 0.5 million have been investigated for multiple angles of attack. Low lift-to-drag ratios were found placing high power requirements for the DiscRotor during fixed-wing flight. By traversing a seven-hole velocity probe, velocities in a 2-D grid perpendicular to the flow were measured on the model. The strengths of shed vortices from the model were calculated. A method to improve fixed-wing performance was considered where two blades were extended from the disc. An increase of 0.17 in the CL was measured due to the interaction between the disc and blades. This research utilized a wide range of experiments, with the aim of generating basic aerodynamic characteristics of the DiscRotor. A substantial amount of quantitative data was collected that could not be included in this document. Results aided in the initial designs of this aircraft for the purpose of evaluating the merit of the DiscRotor concept. / Master of Science

No description available.

No description available.

No description available.

Au cours du siècle dernier, la communauté scientifique a traité le contrôle des véhicules aériens principalement par l'élaboration de stratégies ad hoc, mais aucune approche unifiée n'a été développé jusqu'à présent. Cette thèse participe à l'élaboration d'une approche unifiée pour le contrôle des véhicules aériens en prenant en compte les forces aérodynamiques dans la conception de la commande. Nous supposons les effets aérodynamiques de rotation et les effets non stationnaires négligeables. Les actionneurs du véhicule sont supposés être composés d'une force de poussé fixée au corps pour le mouvement en translation, et d'un couple de contrôle pour la régulation d'attitude. Cette thèse se concentre ensuite sur la boucle de guidage, traitant du contrôle de la vitesse linéaire. L'un des principaux objectifs a été de déterminer la façon de réguler la force de poussée et l'orientation du véhicule pour compenser les forces extérieures. Tout d'abord nous abordons la modélisation, l'analyse et le contrôle de la dynamique longitudinale de l'avion. Ensuite nous étendons certaines de ces études aux mouvements tridimensionnels d'avions au corps symétrique, tels que les missiles. Un résultat original de cette thèse est de préciser les conditions sur la force aérodynamique permettant de reformuler le problème du contrôle dans celui de la commande d'un corps sphérique, pour lequel des résultats de stabilité peuvent être démontrés. Les lois de commande proposées intègrent des termes intégraux et anti-wind up sans reposer sur une politique de commutation entre plusieurs lois de commande. / Over the last century, the scientific community has dealt with the control of flying machines by mainly developing different strategies in relation to different classes of aircraft, and no unified control approach has been developed so far. The present thesis contributes towards the development of a unified control approach for aerial vehicles by maintaining aerodynamic forces in the control design. It is assumed, however, that the aerodynamic effects of rotational and unsteady motions are negligible, and that the means of actuation for an aerial vehicle consist of a body-fixed thrust force for translational motion and a control torque for attitude monitoring. This thesis then focuses on the guidance loop of the control problem. One of the main objectives has been to determine how to regulate the thrust intensity and the vehicle orientation to compensate for the orientation-dependent external forces. In particular, the modeling, analysis, and control of the longitudinal aircraft dynamics is first addressed. Then, some of these studies are extended to three-dimensional motions of symmetric aircraft, such as missile-like bodies. An original outcome of this thesis is to state conditions on the aerodynamic force that allow the control problem to be recasted into that of controlling a spherical body. In this case, strong stability results can be shown. The proposed control laws incorporate integral and anti-wind up terms and do not rely on a switching policy between several control laws.

This dissertation investigates the application of Genetic Algorithms (GA) and Simulated Annealing (SA) based search techniques to the problem of deriving an auto-pilot that can emulate a human operator or other controller flying a Small unmanned Helicopter (SH). A Helicopter is a type of Vertical Take Off and Landing Vehicle (VTOL). The maneuvers are none aggressive, mild maneuvers, that include u-turns, ascending spirals and other none extreme flight paths. The pilot of the helicopter is a Fuzzy logic Controller (FC) pilot; it is assumed that the pilot executes the maneuvers with skill and precision. The FC pilot is given set- points (points in space) that represent a path/flight maneuver and is expected to follow them as closely as possible. Input/Output data is then collected from the FC pilot executing maneuvers in real time. The collected data include control signals from the FC pilot to the SH and the resulting output signals from the SH that include time, x, y, z coordinates and yaw (the angle of the SH relative to the x, y axis). The Genetic Algorithm/Simulated Annealing based search algorithm attempts to generate a set of mathematical formulas that best map the collected data. The search algorithm presented in this dissertation was implemented in Java and has a JSP (Java Server Pages) graphical user interface. The results obtained show that the search technique developed; termed Genetic Algorithm / Simulated Annealing controller or (GA/SA) controller allows for the derivation of accurate SH control equations. The results include performance quantification of the algorithm in the derivation phase and the testing phase. Graphs are included; they demonstrate the accuracy and path data of the GA/SA controller as compared to the FC pilot and other controllers. The final results showing the formulas found are also included. A technique was also developed during this dissertation to encode the genetic strings that represent the candidate formulas during the search. This technique allowed the combination of strings to yield new formulas that are valid. The results can be used by other investigators to expand the complexity of the formulas generated during the search. The technique has advantages such as the ability to operate in open-loop conditions and is able to fly the SH without the need for set-point data and without the need for GPS or some other location determination technology. The technique may be used as a backup controller that can take over control of a helicopter in case the main controller is unable to function due to a GPS malfunction or another situation where accurate positioning data cannot be obtained.

A l'heure actuelle, les projets d'utilisation de drone de petites tailles à capacité de vol stationnaire<br />pour des missions d'observation dans des environnements urbains se multiplient. Les<br />contraintes d'encombrement et de confinement des pales pour la sécurité des utilisateurs ont remis<br />au goût du jour l'utilisation de véhicules à hélices carénées. L'enjeu majeur de ces minidrones est<br />la résistance au vent. Cependant, leur forme atypique et les faibles nombres de Reynolds associés<br />sont à l'origine de phénomènes aérodynamiques dont la caractérisation fine reste un problème<br />largement ouvert. Il est donc nécessaire de développer des stratégies de commande estimant ces<br />efforts en ligne pour pouvoir les contrer. Après une étape de modélisation, nous mettons en<br />évidence une structure chaînée propice à une architecture de contrôle en cascade, combinant un<br />contrôle en position de haut niveau et un contrôle en attitude de bas niveau. Mais proposer une loi<br />de commande pour le maintien à poste ne suffit pas. Encore faut-il, pour pouvoir l'implémenter<br />dans le calculateur, disposer des informations de position et d'attitude pour le contrôle en boucle<br />fermée. Nous proposons des techniques de filtrage pour reconstituer l'état du drone à partir des<br />mesures capteurs. Notre contribution porte sur deux aspects : la conception d'estimateurs non<br />linéaires dans l'espace des matrices orthogonales pour la restitution d'attitude d'une part, et la<br />navigation inertielle hybridée d'autre part. Après avoir fermé la boucle "Observation-Contrôle",<br />nous nous intéressons au problème de la navigation en présence d'obstacle. L'efficacité des méthodes<br />proposées est verifiée par des simulations et des expérimentations menées sur le minidrone<br />à hélice carénée HoverEye développé par la Société Bertin Technologies.

The design, analysis, construction and flight testing of a miniature Vertical Take-Off and Landing (VTOL) tail-sitter Unmanned Aerial Vehicle (UAV) prototype is presented in detail. Classic aircraft design methods were combined with numerical analysis to estimate the aircraft performance and flight characteristics. The numerical analysis employed a propeller blade-element theory coupled with momentum equations to predict the influence of a propeller slipstream on the freestream flow field, then the aircraft was analyzed using 3-D vortex lifting-line theory to model finite wings immersed in the flow field. Four prototypes were designed, built, and tested and the evolution of these prototypes is presented. The final prototype design is discussed in detail. A method for sizing control surfaces for a tail-sitter was defined. The final prototype successfully demonstrated controllability both in horizontal flight and vertical flight. Significant contributions included the development of a control system that was effective in hover as well as descending vertical flight, and the development of a strong but light weight airframe. The aircraft had a payload weight fraction of 14.5% and a maximum dimension of one meter, making it the smallest tail-sitter UAV to carry a useful payload. This project is expected to provide a knowledge base for the future design of small electric VTOL tail-sitter aircraft and to provide an airframe for future use in tail-sitter research.

Small unmanned aircraft and electric vertical takeoff and landing (eVTOL) aircraft have recently emerged as vehicles able to perform new missions and stimulate future air transportation methods. This dissertation presents several system identification research advancements for these modern aircraft configurations enabling accurate mathematical model development for flight dynamics simulations based on wind-tunnel and flight-test data. The first part of the dissertation focuses on advances in flight-test system identification methods using small, fixed-wing, remotely-piloted, electric, propeller-driven aircraft. A generalized approach for flight dynamics model development for small fixed-wing aircraft from flight data is described and is followed by presentation of novel flight-test system identification applications, including: aero-propulsive model development for propeller aircraft and nonlinear dynamic model identification without mass properties. The second part of the dissertation builds on established fixed-wing and rotary-wing aircraft system identification methods to develop modeling strategies for transitioning, distributed propulsion, eVTOL aircraft. Novel wind-tunnel experiment designs and aero-propulsive modeling approaches are developed using a subscale, tandem tilt-wing, eVTOL aircraft, leveraging design of experiments and response surface methodology techniques. Additionally, a method applying orthogonal phase-optimized multisine input excitations to aircraft control effectors in wind-tunnel testing is developed to improve test efficiency and identified model utility. Finally, the culmination of this dissertation is synthesis of the techniques described throughout the document to form a flight-test system identification approach for eVTOL aircraft that is demonstrated using a high-fidelity flight dynamics simulation. The research findings highlighted throughout the dissertation constitute substantial progress in efficient empirical aircraft modeling strategies that are applicable to many current and future aeronautical vehicles enabling accurate flight simulation development, which can subsequently be used to foster advancement in many other pertinent technology areas. / Doctor of Philosophy / Small, electric-powered airplanes flown without an onboard pilot, as well as novel electric aircraft configurations with many propellers that operate at a wide range of speeds, referred to as electric vertical takeoff and landing (eVTOL) aircraft, have recently emerged as aeronautical vehicles able to perform new tasks for future airborne transportation methods. This dissertation presents several mathematical modeling research advancements for these modern aircraft that foster accurate description and prediction of their motion in flight. The mathematical models are developed from data collected in wind-tunnel tests that force air over a vehicle to simulate the aerodynamic forces in flight, as well as from data collected while flying the aircraft. The first part of the dissertation focuses on advances in mathematical modeling approaches using flight data collected from small traditional airplane configurations that are controlled by a pilot operating the vehicle from the ground. A generalized approach for mathematical model development for small airplanes from flight data is described and is followed by presentation of novel modeling applications, including: characterization of the coupled airframe and propulsion aerodynamics and model development when vehicle mass properties are not known. The second part of the dissertation builds on established airplane, helicopter, and multirotor mathematical modeling methods to develop strategies for characterization of the flight motion of eVTOL aircraft. Innovative data collection and modeling approaches using wind-tunnel testing are developed and applied to a subscale eVTOL aircraft with two tilting wings. Statistically rigorous experimentation strategies are employed to allow the effects of many individual controls and their interactions to be simultaneously distinguished while also allowing expeditious test execution and enhancement of the mathematical model prediction capability. Finally, techniques highlighted throughout the dissertation are combined to form a mathematical modeling approach for eVTOL aircraft using flight data, which is demonstrated using a realistic flight simulation. The research findings described throughout the dissertation constitute substantial progress in efficient aircraft modeling strategies that are applicable to many current and future vehicles enabling accurate flight simulator development, which can subsequently be used for many research applications.