In this report, detailed and systematic theoretical and experimental study of low-finesse extrinsic Fabry-Perot interferometric (EFPI) fiber optic sensors together with their signal processing methods for white-light systems are presented. The work aims to provide a better understanding of the operational principle of EFPI fiber optic sensors, and is useful and important in the design, optimization, fabrication and application of single mode fiber(SMF) EFPI (SMF-EFPI) and multimode fiber (MMF) EFPI (MMF-EFPI) sensor systems. The cases for SMF-EFPI and MMF-EFPI sensors are separately considered. In the analysis of SMF-EFPI sensors, the light transmitted in the fiber is approximated by a Gaussian beam and the obtained spectral transfer function of the sensors includes an extra phase shift due to the light coupling in the fiber end-face. This extra phase shift has not been addressed by previous researchers and is of great importance for high accuracy and high resolution signal processing of white-light SMF-EFPI systems. Fringe visibility degradation due to gap-length increase and sensor imperfections is studied. The results indicate that the fringe visibility of a SMF-EFPI sensor is relatively insensitive to the gap-length change and sensor imperfections. Based on the spectral fringe pattern predicated by the theory of SMF-EFPI sensors, a novel curve fitting signal processing method (Type 1 curve-fitting method) is presented for white-light SMF-EFPI sensor systems. Other spectral domain signal processing methods including the wavelength-tracking, the Type 2-3 curve fitting, Fourier transform, and two-point interrogation methods are reviewed and systematically analyzed. Experiments were carried out to compare the performances of these signal processing methods. The results have shown that the Type 1 curve fitting method achieves high accuracy, high resolution, large dynamic range, and the capability of absolute measurement at the same time, while others either have less resolution, or are not capable of absolute measurement. Very different from SMF-EFPI sensors, MMF-EFPI sensors with high fringe visibility usually are more difficult to obtain in practice because the fringe visibility of a MMF-EFPI sensor is much more sensitive to gap-length change and sensor head imperfections. %Previously, only geometric-optics are available to analyze MMF-EFPI sensors which approximate the light in MMF as rays propagating in different directions. Geometric-optics theory has fundenmental limitations because it is approximate and only valid for limited conditions. Moreover, geometric-optics theory is not capable of poviding the exact fringe pattern which is important in the signal processing of white light MMF-EFPI sensor systems. In this report, Previous mathematical models for MMF-EFPI sensors are all based on geometric optics; therefore their applications have many limitations. In this report, a modal theory is developed that can be used in any situations and is more accurate. The mathematical description of the spectral fringes of MMF-EFPI sensors is obtained by the modal theory. Effect on the fringe visibility of system parameters, including the sensor head structure, the fiber parameters, and the mode power distribution in the MMF of the MMF-EFPI sensors, is analyzed. Experiments were carried out to validate the theory. Fundamental mechanism that causes the degradation of the fringe visibility in MMF-EFPI sensors are revealed. It is shown that, in some situations at which the fringe visibility is important and difficult to achieve, a simple method of launching the light into the MMF-EFPI sensor system from the output of a SMF could be used to improve the fringe visibility and to ease the fabrication difficulties of MMF-EFPI sensors. Signal processing methods that are well-understood in white-light SMF-EFPI sensor systems may exhibit new aspects when they are applied to white-light MMF-EFPI sensor systems. This report reveals that the variations of mode power distribution (MPD) in the MMF could cause phase variations of the spectral fringes from a MMF-EFPI sensor and introduce measurement errors for a signal processing method in which the phase information is used. This MPD effect on the wavelength-tracking method in white-light MMF-EFPI sensors is theoretically analyzed. The fringe phases changes caused by MPD variations were experimentally observed and thus the MFD effect is validated. / Ph. D.

Interferometric fiber optic sensors have been extensively used to measure a large variety of physical, chemical and biomedical parameters due to their superior performance. At the Center for Photonics Technology of Virginia Tech, a variety of interferometric fiber optic sensors have been developed in recent years, for efficient oil recovery, partial discharge detection in high voltage transformers, pressure sensing in gas turbine engines, and temperature measurements in gasifiers and boilers. However, interrogating an interferometric sensor involves accurate recovery of a measurand from the phase-modulated lightwaves, and has been a challenge for high performance, high speed, and low-cost, to current white-light interferometry (WLI) techniques, such as the widely used scanning WLI (S-WLI) and spectral-domain WLI (SD-WLI). The performance of a white-light interferometric sensing system depends not only on the design of the probes, but also, to a great extent, on the interrogation strategy to be used. In this Ph.D. research, a tunable optical filter based WLI (TOF-WLI) is proposed and validated as a low cost, yet high performance, solution to the interrogation of various types of interferometric sensors. In addition to the capability of linear/quadrature demodulation, TOF-WLI retains all the features of WLI, is compatible with the SD-WLI, and can be tailored for both static and wideband signals. It also has great potential in surface metrology and biomedical imaging as well as optical spectroscopy. The key, to the success of this new approach in competition with the other available WLI techniques, is that the tunable optical filter (TOF) must be specially designed for sensing and extremely low cost. Therefore, two novel TOFs, a diffraction grating tunable filter (DG-TOF) and an extrinsic Fabry-Perot tunable filter (EFP-TF), are proposed and demonstrated. Laboratory and field test results on using the DG-TOF WLI for partial discharge and thermal fault detection in high voltage power transformers, and the EFP-TF WLI in temperature sensor systems and a turbine engine monitoring system will also be presented to demonstrate the feasibility for efficient sensor interrogation. / Ph. D.

This dissertation addresses several theoretical issues in low-finesse fiber optic Fabry-Perot Interferometric (FPI) sensors. The work is divided into two levels: modeling of the sensors, and signal processing based on White-Light-Interferometry (WLI). In the first chapter, the technical background of the low-finesse FPI sensor is briefly reviewed and the problems to be solved are highlighted. A model for low finesse Extrinsic FPI (EFPI) is developed in Chapter 2. The theory is experimentally proven using both single-mode and multimode fiber based EFPIs. The fringe visibility and the additional phase in the spectrum are found to be strongly influenced by the optical path difference (OPD), the output spatial power distribution and the working wavelength; however they are not directly related to the light coherence. In Chapter 3, the Single-Multi-Single-mode Intrinsic FPI (SMS-IFPI) is theoretically and experimentally studied. Reflectivity, cavity refocusing, and the additional phase in the sensor spectrum are modeled. The multiplexing capacity of the sensor is dramatically increased by promoting light refocusing. Similar to EFPIs, wave-front distortion generates an additional phase in the interference spectrogram. The resultant non-constant phase plays an important role in causing abrupt jumps in the demodulated OPD. WLI-based signal processing of the low-finesse FP sensor is studied in Chapter 4. The lower bounds of the OPD estimation are calculated, the bounds are applied to evaluate OPD demodulation algorithms. Two types of algorithms (TYPE I & II) are studied and compared. The TYPE I estimations suffice if the requirement for resolution is relatively low. TYPE II estimation has dramatically reduced error, however, at the expense of potential demodulation jumps. If the additional phase is reliably dependent on OPD, it can be calibrated to minimize the occurrence of such jumps. In Chapter 5, the work is summarized and suggestions for future studies are given. / Ph. D.

Sapphire fiber based temperature sensors are exceptional in their ability to operate at temperatures above 1000C and as high as 1800C. Sapphire fiber technology is emerging and the fiber is available commercially. Sapphire fiber has a high loss, is highly multi-mode and does not have a solid cladding, but it is nonetheless very useful in high temperature applications. Of the available interferometer configurations, Fabry-Perot interferometers are distinguished in their high accuracy and great isolation from sources of error. In this thesis, improvements are reported to an existing design to enhance its reliability and to reduce possible modes of failure. The existing high temperature sensor design has shown a lot of potential in the past by continuously measuring the temperature in a coal gasifier for 7 months, but its true potential has not yet been realized. The goal of this work and the work of many others is to extend the working life and reliability of high-temperature optical sapphire temperature sensors in harsh environments by exploring a solid cladding for sapphire fiber, improved fringe visibility sapphire wafers and a new sensor design. This project is supported by the National Energy and Technology Laboratory of the Department of Energy. / Master of Science

As specialized materials are developed for various applications, it becomes desirable to test them under adverse conditions, such as at elevated temperatures and in harsh environments. It is increasingly important that sensors be developed to meet the growing needs of research and industry. The ability of sapphire to withstand elevated temperatures and many chemically harsh environments has long been recognized. However, currently available sapphire fiber possesses poor optical quality and is not available with a cladding. It has found use in a variety of temperature sensors, but the investigation of sapphire-based strain and displacement sensors has been limited. The primary development of a white-light Michelson interferometer that utilizes a sapphire fiber sensing head is presented in this thesis. Development includes efforts to combat the poor optical quality of the sapphire fiber, minimize polarization mode fading, and preferentially excite the fundamental mode of the sapphire fiber. This thesis demonstrates the feasibility of fabricating a Michelson white-light interferometer capable of measuring displacements in environments ranging from room temperature to 800 degrees Celsius. The sensor developed in this work is capable of measuring displacements exceeding 6.4 millimeters at room temperature, and exceeding 1 millimeter at 800 degrees Celsius. This thesis also presents the application of this sensor to the alignment of a sapphire-fiber based Fabry-Perot sensor. This technique allows the Fabry-Perot sensor to be aligned so that usable fringes are always obtained. Alignment of the sapphire-fiber based Fabry-Perot sensors has been considered prohibitively difficult. / Master of Science

Carbon nanoparticles (CNPs) have drawn great attention in the last few years owing to their unique properties such as excellent water solubility, chemical stability, inertness, low toxicity, good bio-compatibility, and tunable photo physical properties. Recently, researchers have focused on hetero atom (N, S and B) doped CNPs due to their excellent properties. These properties make the CNPs and doped CNPs as potential candidates for a wide range of applications. For example, metal ion detection in aqueous solution, bio-imaging, bio-sensing, photovoltaic devices, cleavage of deoxyribonucleic acid (DNA), and catalysis. Therefore, CNPs are alternative to inorganic semiconductor nanoparticles. However, CNPs with diameter less than 10 nm have been prepared using various approaches including top down and bottom methods. Cutting the bulk carbon from high dimensional to zero dimensional by using either physical or chemical process are classified as top down method. Bottom up method refers the conversion of organic precursor to nano-carbon by using thermal pyrolysis, microwave based hydrothermal method, cage opening of C60 molecules. In the present work, I have dealt with the facile synthesis of CNPs and different hetero atom doped carbon nanoparticles (N-CNPs, B-CNPs, and BN-CNPs) using the hydrothermal method. Based on their intriguing physical and chemical properties, these CNPs/doped-CNPs have been explored for various applications such as (i) metal-free catalysts, (ii) color tunability from red to blue and bio-imaging, (iii) ammonia sensing, (iv) white light generation, and (v) detection of picric acid (PA) in aqueous solution. Finally, I have presented 3D nanodendrites of N-CNPs and Pd NPs and their excellent catalytic mass activity for methanol electro-oxidation and ultra-fast reduction of 4-nitrophenol.

No description available.

Hologramas podem ser produzidos utilizando-se técnicas tradicionais de holografia ou podem ser gerados também por computador, conhecidos como hologramas gerados por computador (HGCs). A maioria destes hologramas opera usando luz monocromática. Por outro lado, os hologramas podem também operar com luz branca. Estes elementos de luz branca são usados em diversas aplicações, como segurança, para verificar a autenticidade dos cartões de crédito e outros documentos, porque seus processos de fabricação são difíceis e caros de serem reproduzidos. Entretanto, os hologramas de luz branca convencionais operam baseados na reflexão da luz, e apresentam alguns efeitos indesejáveis, como distorções cromáticas, como o efeito rainbow. Neste trabalho foi proposto um elemento óptico difrativo de luz branca gerado por computador. O elemento é calculado baseado na técnica de halftoning e na coerência espacial parcial de uma fonte de luz branca estendida. Os elementos da fase são produzidos através de técnicas de fabricação bem estabelecidas de circuitos integrados, e as simulações óticas são apresentadas. Não há necessidade de métodos iterativos. Os resultados das reconstruções ópticas e simuladas deste elemento de luz branca são muito semelhantes e produzem imagens nítidas, não sendo observadas distorções cromáticas. O elemento de luz branca ainda não foi descrito na literatura, e algumas de suas aplicações podem ser um correlator óptico ou arte holográfica. Este trabalho foi realizado no laboratório de óptica do departamento da engenharia elétrica do EESC, e financiado por CAPES (Coordenadoria de Aperfeiçoamento de Pessoal de Nível Superior). / Holograms can be produced using traditional holography techniques or may be also generated by computer, which are known as CGHs(Computer-generated holograms). Most of these holograms operate using monochromatic light. On the other hand, holograms can also operate with white light. These white light holograms are used in several applications, such as security, to verify the autencity of credit cards end other documents, because their fabrication processes are dificult to reproduce and are expensive. However, convencional white light holograms operate based on reflection of light, and present some undesirable effects, like chromatic distortions, such as rainbow effect. In this work it was proposed a computer-generated phase optical difractive element designed to operate under white light illumination. The element is calculated based on the halftoning technique and in the partial spatial coherence of a white light extended source. Phase elements are manufactured using well-established integrated circuits fabrication techniques and optical simulations are shown. No iterative methods are necessary. Simulated and optical reconstructions results are very similar and produce good clear images, and no chromatic distortions are observed. The white light element was not yet described on literature, and some of its applications may be an optical correlator or holographic art. This work was carried at the laboratory of optics of the department of electrical engineering of the EESC, and supported by CAPES (Coordenadoria de Aperfeiçoamento dePessoal de Nível Superior).

One of the key measurement devices used in characterization of microelectromechanical systems (MEMS) is the interferometric microscope. This device allows remote, noninvasive measurements of the surface shape and deformations of MEMS in full-field-of-view with high spatial resolution and nanometer accuracy in near real-time. As MEMS are becoming more prevalent in the areas of consumer products and national defense, the demand for a versatile and easy to use characterization system is very high. This Thesis describes the design, implementation, and use of an interferometric system that is based on modular components which allow for many loading and measurement capabilities, depending on a specific application. The system has modules for subjecting MEMS to vacuum and dry gas environments, mechanical vibration excitation, thermal loads (both heating and cooling), and electrical loads. Three interferometric measurement modules can be interchanged to spatially measure shape and deformation of micro- and/or meso-scale objects, and temporally measure vibrations of these objects. Representative examples of the measurement and loading capabilities of the system are demonstrated with microcantilevers and a microgyroscope.

This thesis focuses on development of novel nanomaterials, including semiconductor quantum dots (QDs) and gold nanoparticles (AuNPs), for fabricating white-light emitting devices and assaying thiols in biological and environmental samples. The thesis mainly contains two divisions. One demonstrates synthesis, optical properties and white-light emissions of alloyed quantum dots and their application to light-emitting devices. The other describes to combine functionalized gold nanoparticles with capillary electrophoresis and accomplish high selectivity and ultrasensitive detection for thiols. First, through one-step aqueous synthesis, alloyed ZnxCd1¡VxSe QDs have been successfully prepared at low temperatures by reacting a mixture of Cd(ClO4)2 and Zn(ClO4)2 with NaHSe using 3-mercaptopropionic acid as a surface-stabilizing agent. The optical properties and composition of the alloyed QDs were highly dependent on the molar ratio of Zn2+ to Cd2+. With the increase in Zn content, a systematic blue shift occurred in the first exciton absorption and band edge emission. Moreover, X-ray diffraction peaks of the alloyed QDs systematically shifted to larger angles simultaneously. These systematic shifts indicated the formation of the alloyed QDs. Interestingly, among these alloyed QDs, Zn0.93Cd0.07Se QDs exhibited white-light emission with quantum yields of 12%. In addition, we discovered that we could adjust the relative strength of the band edge and trap state emissions by controlling the reaction time, thereby attain white-light-emitting QDs. Finally, we blended alloyed QDs with ultraviolet-transparent polydimethylsiloxane (PDMS) to develop a white-light, solid-state lighting device by using a 365-nm UV lamp as the pump source. In the other part of this thesis, we proposed a method for selective enrichment of thiols using Tween 20-capped gold nanoparticles (AuNPs) prior to capillary electrophoresis coupled with laser-induced fluorescence (CE-LIF). By forming Au-S bonds, Tween 20-AuNPs can selectively extract thiols from a complicated matrix. A Tween 20 capping layer not only suppresses nonspecific adsorption, but also enables NPs to disperse in a highly-salinity solution. For analyses of aminothiols, after extraction and centrifugation, thioglycollic acid was utilized to remove aminothiols that attached to the NP surfaces. The extracted aminothiols was derivatized with o-phthalaldehyde (OPA) followed by CE-LIF. The use of this nanoprobe provided approximately 11-, 282-, and 21-fold sensitivity improvements for homocysteine (HCys), glutathione (GSH), and £^-glutamylcysteine (GluCys), respectively. Furthermore, the limits of detection (LODs) at a signal-to-noise ratio of 3 for HCys, GSH, and GluCys are 4013, 80, and 383 pM, respectively. A practical analysis of aminothiols in human urine sample has been accomplished by our proposed method. For another application to determining thiol-containing peptides, we use dithiothreitol to remove thiol-containing peptides from the NP surface through ligand exchange. The released peptides are selectively derivatized with OPA to form tricyclic isoindole derivatives. After injecting a large sample volume, the sensitivity of these peptides was improved by stacking them via using polyethylene oxide (PEO) as additive for on-line concentration and separation. As a result, LODs for GSH, GluCys, and phytochelatins (PC2 ~ PC4) were down to 0.1-6 pM. The proposed method has the lowest LODs for five peptides compared to other reported methods, and it also detect dissolve thiols in seawater in practice. Our proposed method is capable of ultrasensitive detection for thiols in biological and environmental samples.