Over the last few years, wireless cellular communications has experienced rapid growth in the demand for provision of high data rate wireless multimedia services. This fact motivates the need to find ways to improve the spectrum efficiency of wireless communication systems. Smart or adaptive antennas have emerged as a promising technology to enhance the spectrum efficiency of present and future wireless communications systems by exploiting the spatial domain. The aim of this thesis is to investigate smart antenna applications for Direct Sequence Code Division Multiple Access (DS-CDMA) systems. CDMA is chosen as the platform for this thesis work since it has been adopted as the air-interface technology by the Third Generation (3G) wireless communication systems. The main role of smart antennas is to mitigate Multiple Access Interference (MAI) by beamforming (i.e. spatial filtering) operation. Therefore, irrespective of a particular wireless communication system, it is important to consider whether a chosen array configuration will enable optimal performance. In this thesis an initial assessment is carried out considering linear and circular array of dipoles, that can be part of a base station antenna system. A unified and systematic approach is proposed to analyse and compare the interference rejection capabilities of the two array configurations in terms of the Signal to Interference Ratio (SIR) at the array output. The theoretical framework is then extended to include the effect of mutual coupling, which is modelled using both analytical and simulation methods. Results show that when the performance is averaged over all angles of arrival and mutual coupling is negligible, linear arrays show similar performance as circular arrays. Thus in the remaining part of this thesis, only linear arrays are considered. In order to properly evaluate the performance of smart antenna systems, a realistic channel model is required that takes into account both temporal and spatial propagation characteristics of the wireless channel. In this regard, a novel parameterized physical channel model is proposed in this thesis. The new model incorporates parameters such as user mobility, azimuth angle of arrival, angle spread and Doppler frequency, which have critical influence on the performance of smart antennas. A mathematical formulation of the channel model is presented and the proposed model is implemented in software using Matlab. The statistics of the simulated channels are analysed and compared with theory to confirm that the proposed model can accurately simulate Rayleigh and Rician fading characteristics. To assist system planners in the design and deployment of smart antennas, it is important to develop robust analytical tools to assess the impact of smart antennas on cellular systems. In this thesis an analytical model is presented for evaluating the Bit Error Rate (BER) of a DS-CDMA system employing an array antenna operating in Rayleigh and Rician fading environments. The DS-CDMA system is assumed to employ noncoherent M-ary orthogonal modulation, which is relevant to IS-95 CDMA and cdma2000. Using the analytical model, an expression of the Signal to Interference plus Noise Ratio (SINR) at the output of the smart antenna receiver is derived, which allows the BER to be evaluated using a closed-form expression. The proposed model is shown to provide good agreement with the (computationally intensive) Monte Carlo simulation results and can be used to rapidly calculate the system performance for suburban and urban fading environments. In addition to MAI, the performance of CDMA systems is limited by fast fading. In this context, a hybrid scheme of beamforming and diversity called Hierarchical Beamforming (HBF) is investigated in this thesis to jointly combat MAI and fading. The main idea behind HBF is to divide the antenna elements into widely separated groups to form subbeamforming arrays. The performance of a hierarchical beamforming receiver, applied to an IS-95 CDMA system, is compared with smart antenna (conventional beamforming) receiver and the effect of varying the system and channel parameters is studied. The simulation results show that the performance of hierarchical beamforming is sensitive to the operating conditions, especially the value of the azimuth angle spread. The work presented in this thesis has been published in part in several journals and refereed conference papers, which reflects the originality and significance of the thesis contributions.

Digital communication systems which use Orthogonal Frequency Division Multiplexing (OFDM) are now widely used and have many advantages. The main disadvantage is the requirement for highly linear analogue electronics including the high power amplifier (HPA). This requirement cannot be met in all circumstances because of the occurrence of symbols with high peak to average power ratio (PAPR). Such symbols may be non-linearly distorted by limiting. Approaches to solve this problem have been either to reduce the PAPR at the transmitter or to try to mitigate the effect of the non-linearity at the receiver. Soft-limiting, i.e. applying limiting in software prior to the HPA is a simple way to reduce the PAPR. It produces non-linear distortion which will cause an increase in the bit-error-rate (BER) at the receiver. This thesis surveys existing alternatives ways of reducing the effect of non-linearity and proposes some new ones. Two iterative receiver techniques, based on statistical analysis of the nature of the non-linearity, have been implemented and investigated. These are the ‘Bussgang Noise Cancellation’ (BNC) technique and the ‘Decision Aided Reconstruction’ (DAR) techniques. As these techniques are valid for any memory-less nonlinearity, an alternative form of limiting, named as Inverted-Wraparound (IWRAP) has been included in the BNC investigation. A new method is proposed which is capable of correcting the received time-domain samples that are clipped, once they have been identified. This is named the ‘Equation-Method’ and it works by identifying constellation symbols that are likely to be correct at the receiver. If there are a sufficient number of these and they are correctly identified, the FFT may be partitioned to produce a set of equations that may be solved for the clipped time-domain samples. The thesis proposes four enhancements to this new method which improve its effectiveness. It is shown that the best form of this method outperforms conventional techniques especially for severe clipping levels. The performance of these four enhancements is evaluated over channels with additive white Gaussian noise (AWGN) in addition to clipping distortion. A technique based on a ‘margin factor’ is designed to make these methods work more effectively in the presence of AWGN noise. A new combining algorithm referred as ‘HARQ for Clipping’ is presented where soft bit decisions are combined from multiple transmissions. ‘HARQ for Clipping’ has been combined with the best version of the Equation-Method, and the performance of this approach is evaluated in terms of the BER with different levels of AWGN. It has been compared to other approaches from the literature and was found to out-perform the BNC iterative receiver by 3dB at signal to noise ratios around 10dB. Without HARQ, the best version of the Equation-Method performs better than the BNC receiver, at signal-to-nose ratios above about 17dB.

Ce travail vise la modélisation au niveau système, en langage SystemC-AMS, et la simulation d'un émetteur-récepteur au standard Bluetooth Low Energy (BLE). L'objectif est d'analyser la relation entre les performances, en termes de BER et la consommation d'énergie du transceiver. Le temps de simulation d’un tel système, à partir de cas d’étude (use case) réaliste, est un facteur clé pour le développement d’une telle plateforme. De plus, afin d’obtenir des résultats de simulation le plus précis possible, les modèles « haut niveau » doivent être raffinés à partir de modèles plus bas niveau où de mesure. L'approche dite Meet-in-the-Middle, associée à la méthode de modélisation équivalente en Bande Base (BBE, BaseBand Equivalent), a été choisie pour atteindre les deux conditions requises, à savoir temps de simulation « faible » et précision des résultats. Une simulation globale d'un système de BLE est obtenue en intégrant le modèle de l'émetteur-récepteur dans une plateforme existante développée en SystemC-TLM. La simulation est basée sur un système de communication de deux dispositifs BLE, en utilisant différents scénarios (différents cas d'utilisation de BLE). Dans un premier temps nous avons modélisé et validé chaque bloc d’un transceiver BT. Devant le temps de simulation prohibitif, les blocs RF sont réécrits en utilisant la méthodologie BB, puis raffinés afin de prendre en compte les non-linéarités qui vont impacter le couple consommation, BER. Chaque circuit (chaque modèle) est vérifié séparément, puis une première simulation système (point à point entre un émetteur et un récepteur) est effectuée / This work aims at system-level modelling a defined transceiver for Bluetooth Low energy (BLE) system using SystemC-AMS. The goal is to analyze the relationship between the transceiver performance and the accurate energy consumption. This requires the transceiver model contains system-level simulation speed and the low-level design block power consumption and other RF specifications. The Meet-in-the-Middle approach and the Baseband Equivalent method are chosen to achieve the two requirements above. A global simulation of a complete BLE system is achieved by integrating the transceiver model into a SystemC-TLM described BLE system model which contains the higher-than-PHY levels. The simulation is based on a two BLE devices communication system and is run with different BLE use cases. The transceiver Bit-Error-Rate and the energy estimation are obtained at the end of the simulation. First, we modelled and validated each block of a BT transceiver. In front of the prohibitive simulation time, the RF blocks are rewritten by using the BBE methodology, and then refined in order to take into account the non-linearities, which are going to impact the couple consumption, BER. Each circuit (each model) is separately verified, and then a first BLE system simulation (point-to-point between a transmitter and a receiver) has been executed. Finally, the BER is finally estimated. This platform fulfills our expectations, the simulation time is suitable and the results have been validated with the circuit measurement offered by Riviera Waves Company. Finally, two versions of the same transceiver architecture are modelled, simulated and compared

Explosive growth in wireless technology caused by development in digital and RF circuit fabrications put some serious challenges on wireless system designers and link budget planning. Low transmit power, system coverage and capacity, high data rates, spatial diversity and quality of services (QOS) are the key factors in future wireless communication system that made it attractive. Dual-hop relaying is the promising underlying technique for future wireless communication to address such dilemmas. Based on dual-hop relaying this thesis addresses two scenarios. In the first case the system model employs dual-hop amplify and forward (AF) multiple input multiple output (MIMO) relay channels with transmit and receive antenna selection over independent Rayleigh fading channels where source and destination contain multiple antennas and communicate with each other with help of single antenna relay. It is assumed that the source and destination has perfect knowledge of channel state information (CSI). Our analysis shows that full spatial diversity order can be achieved with minimum number of antennas at source and destination i.e. min{N_s N_d }. In the second case the performance analysis of dual-hop amplify and forward (AF) multiple relay cooperative diversity network with best relay selection schemes over Rayleigh fading channels is investigated where the source and destination communicate with each other through direct and indirect links. Only the performance of best relay is investigated which participates in the transmission alone. The relay node that achieves highest SNR at the destination is selected as a best relay. Once again our analysis shows that full diversity order can be achieved with single relay with fewer resources compare to the regular cooperative diversity system. / Muhammad Adeel Islam 0046 700 412 343

Code Division Multiple Access (CDMA) is the technology used in all third generation cellular communications networks, and it is a promising candidate for the definition of fourth generation standards. The wireless mobile channel is usually frequency-selective causing interference among the users in one CDMA cell. Multiuser Transmission (MUT) algorithms for the downlink can increase the number of supportable users per cell, or decrease the necessary transmit power to guarantee a certain quality-of-service. Transmitter-based algorithms exploiting the channel knowledge in the transmitter are also motivated by information theoretic results like the Writing-on-Dirty-Paper theorem. The signal-to-noise ratio (SNR) is a reasonable performance criterion for noise-dominated scenarios. Using linear filters in the transmitter and the receiver, the SNR can be maximized with the proposed Eigenprecoder. Using multiple transmit and receive antennas, the performance can be significantly improved. The Generalized Selection Combining (GSC) MIMO Eigenprecoder concept enables reduced complexity transceivers. Methods eliminating the interference completely or minimizing the mean squared error exist for both the transmitter and the receiver. The maximum likelihood sequence detector in the receiver minimizes the bit error rate (BER), but it has no direct transmitter counterpart. The proposed Minimum Bit Error Rate Multiuser Transmission (TxMinBer) minimizes the BER at the detectors by transmit signal processing. This nonlinear approach uses the knowledge of the transmit data symbols and the wireless channel to calculate a transmit signal optimizing the BER with a transmit power constraint by nonlinear optimization methods like sequential quadratic programming (SQP). The performance of linear and nonlinear MUT algorithms with linear receivers is compared at the example of the TD-SCDMA standard. The interference problem can be solved with all MUT algorithms, but the TxMinBer approach requires less transmit power to support a certain number of users. The high computational complexity of MUT algorithms is also an important issue for their practical real-time application. The exploitation of structural properties of the system matrix reduces the complexity of the linear MUT mthods significantly. Several efficient methods to invert the ystem matrix are shown and compared. Proposals to reduce the omplexity of the Minimum Bit Error Rate Multiuser Transmission mehod are made, including a method avoiding the constraint by pase-only optimization. The complexity of the nonlinear methods i still some magnitudes higher than that of the linear MUT lgorithms, but further research on this topic and the increasing processing power of integrated circuits will eventually allow to exploit their better performance. / Der codegeteilte Mehrfachzugriff (CDMA) wird bei allen zellularen Mobilfunksystemen der dritten Generation verwendet und ist ein aussichtsreicher Kandidat für zukünftige Technologien. Die Netzkapazität, also die Anzahl der Nutzer je Funkzelle, ist durch auftretende Interferenzen zwischen den Nutzern begrenzt. Für die Aufwärtsstrecke von den mobilen Endgeräten zur Basisstation können die Interferenzen durch Verfahren der Mehrnutzerdetektion im Empfänger verringert werden. Für die Abwärtsstrecke, die höhere Datenraten bei Multimedia-Anwendungen transportiert, kann das Sendesignal im Sender so vorverzerrt werden, dass der Einfluß der Interferenzen minimiert wird. Die informationstheoretische Motivation liefert dazu das Writing-on-Dirty-Paper Theorem. Das Signal-zu-Rausch-Verhältnis ist ein geeignetes Kriterium für die Performanz in rauschdominierten Szenarien. Mit Sende- und Empfangsfiltern kann das SNR durch den vorgeschlagenen Eigenprecoder maximiert werden. Durch den Einsatz von Mehrfachantennen im Sender und Empfänger kann die Performanz signifikant erhöht werden. Mit dem Generalized Selection MIMO Eigenprecoder können Transceiver mit reduzierter Komplexität ermöglicht werden. Sowohl für den Empfänger als auch für den Sender existieren Methoden, die Interferenzen vollständig zu eliminieren, oder den mittleren quadratischen Fehler zu minimieren. Der Maximum-Likelihood-Empfänger minimiert die Bitfehlerwahrscheinlichkeit (BER), hat jedoch kein entsprechendes Gegenstück im Sender. Die in dieser Arbeit vorgeschlagene Minimum Bit Error Rate Multiuser Transmission (TxMinBer) minimiert die BER am Detektor durch Sendesignalverarbeitung. Dieses nichtlineare Verfahren nutzt die Kenntnis der Datensymbole und des Mobilfunkkanals, um ein Sendesignal zu generieren, dass die BER unter Berücksichtigung einer Sendeleistungsnebenbedingung minimiert. Dabei werden nichtlineare Optimierungsverfahren wie Sequentielle Quadratische Programmierung (SQP) verwendet. Die Performanz linearer und nichtlinearer MUT-Verfahren MUT-Algorithmen mit linearen Empfängern wird am Beispiel des TD-SCDMA-Standards verglichen. Das Problem der Interferenzen kann mit allen untersuchten Verfahren gelöst werden, die TxMinBer-Methode benötigt jedoch die geringste Sendeleistung, um eine bestimmt Anzahl von Nutzern zu unterstützen. Die hohe Rechenkomplexität der MUT-Algorithmen ist ein wichtiges Problem bei der Implementierung in Real-Zeit-Systemen. Durch die Ausnutzung von Struktureigenschaften der Systemmatrizen kann die Komplexität der linearen MUT-Verfahren signifikant reduziert werden. Verschiedene Verfahren zur Invertierung der Systemmatrizen werden aufgezeigt und verglichen. Es werden Vorschläge gemacht, die Komplexität der Minimum Bit Error Rate Multiuser Transmission zu reduzieren, u.a. durch Vermeidung der Sendeleistungsnebenbedingung durch eine Beschränkung der Optimierung auf die Phasen des Sendesignalvektors. Die Komplexität der nichtlinearen Methoden ist um einige Größenordungen höher als die der linearen Verfahren. Weitere Forschungsanstrengungen an diesem Thema sowie die wachsende Rechenleistung von integrierten Halbleitern werden künftig die Ausnutzung der besseren Leistungsfähigkeit der nichtlinearen MUT-Verfahren erlauben.

Diploma thesis focuses on simultaneous transmission of selected photonic services by one single-mode optical fiber. The thesis deals with the problem of common transmission of multiple photonic services by one optical fiber using the wavelength division multiplex technology. Furthermore, the origin and influence of nonlinear phenomena accompanying the simultaneous transmission of photonic services are described. Except common data transmission with a bitrate of 10 Gbit/s, a common high-speed data signal transmission with a bitrate of 200 Gbit/s, accurate time transmission and high-power sensor signal are considered. During the aimultaneous transmission of selected photonic services, the measurement of the transmission parameters was performed for various variants of the simultaneous transmission arrangement. In particular, the influence of nonlinear phenomena and possible mutual interference of individual transmission channels at 50 and 100 GHz between signals was analyzed.

This thesis describes and models wirelesss transmission intereferences in real communication channels. A signal received on a fading channel is subjected to a multiplicative distortion and to the usual additive noise. Real channel adds to the signal noise and fadings. Gaussian noise is a result of channel awgn. Fadings is implicated by multipath propagation of signal in Rayleigh and Rician channels. Main goal of this project is to program BERsolve, which is created in tool GUIDE in Matlab. User program BERsolve makes it possible to analyse bit error rate and symbol error rate for some types of channel models, which are defined by standard COST207. BERsolve offers some other functions i.e. display time behaviour, constellation diagram and spectrum. This program provides us with an overview representation of problem by multipath interferences in communication channels.

The diploma thesis Simulation of Multipath Propagation of Multistate Modulations is focused on the development of an appropriate algorithm in MATLAB environment, which is capable to simulate the impact of the multipath propagation on received signal (error rate) on the basis of given parameters of the transmission channels. Mechanisms and characteristics of the wave propagation in communication environment, types of digital modulations and their most important parameters are described in the first part of this thesis. The second part is focused on the simulation itself. Created GUI (Graphical User Interface) is able to display constellation diagrams of transmitted and received signals, as well as their bit error rate. It is also possible to compare these data with the data of signal, which is passed by a non-fading channel.

The work explores ways to generate the OFDM signal and LDPC channel coding methods. Describes the creation of basic modules of the communication system in Matlab and simulation methods for atmospheric transmission environment, including effects of turbulence, attenuation along the route and weather conditions on the transmitted signal.

Most modern clock and data recovery circuits (CDR) are based on analog blocks that need to be redesigned whenever the technology process is to be changed. On the other hand, CDR based blind oversampling architecture (BO-CDR) can be completely designed in a digital process which makes its migration very simple. The main disadvantages of the BO-CDR that are usually mentioned in a literature are complexity of its digital circuitry and finite phase resolution resulting in larger jitter sensitivity and higher error rate. This thesis will show that those problems can be solved by designing a new algorithm of BO-CDR and subsequent optimization. For this task an FPGA was selected as simulation and verification platform. This enables to change parameters of the optimized circuit in real time while measuring on real links (unlike a simulation using inaccurate link models). The output of this optimization is a new BO-CDR algorithm with heavily reduced complexity and very low error rate. A new FPGA-based method of jitter measurement was developed (primary for CDR analysis), which enables a quick link characterization without using probing or additional equipment. The new method requires only a minimum usage of FPGA resources. Finally, new measurement equipment was developed to measure bit error distribution on FSO links to be able to develop a suitable error correction scheme based on ARQ protocol.