Global ETD Search

1	The Study of Buckling Behavior of Al-foil With Central Crack Jin, YiPing, Wang, FengYuan January 2019 (has links) The present paper studied the buckling phenomena of membranes under tensile load with and without central crack. The studies of fracture mechanics are tested within certain conditions of membranes. The tensile test has been performed with Al-foil in different crack lengths, i.e. 0 mm, 12.5 mm, 25 mm and 50 mm. The numerical analysis has been carried out by Finite Element Analysis (FEA) and comparing with the theoretical and experimental results. In this paper, the critical buckling behavior is tested, validated and compared. Same observation of patterns in experiments and the simulation are found. The influence of scale factor for imperfection setting are tested. Buckling Critical Buckling Stress Deflection Membrane Finite Element Analysis (FEA) Imperfection Wrinkling Mechanical Engineering Maskinteknik
2	Strengthening Mechanisms in Microtruss Metals Ng, Evelyn 18 December 2012 (has links) Microtrusses are hybrid materials composed of a three-dimensional array of struts capable of efficiently transmitting an externally applied load. The strut connectivity of microtrusses enables them to behave in a stretch-dominated fashion, allowing higher specific strength and stiffness values to be reached than conventional metal foams. While much attention has been given to the optimization of microtruss architectures, little attention has been given to the strengthening mechanisms inside the materials that make up this architecture. This thesis examines strengthening mechanisms in aluminum alloy and copper alloy microtruss systems with and without a reinforcing structural coating. C11000 microtrusses were stretch-bend fabricated for the first time; varying internal truss angles were selected in order to study the accumulating effects of plastic deformation and it was found that the mechanical performance was significantly enhanced in the presence of work hardening with the peak strength increasing by a factor of three. The C11000 microtrusses could also be significantly reinforced with sleeves of electrodeposited nanocrystalline Ni-53wt%Fe. It was found that the strength increase from work hardening and electrodeposition were additive over the range of structures considered. The AA2024 system allowed the contribution of work hardening, precipitation hardening, and hard anodizing to be considered as interacting strengthening mechanisms. Because of the lower formability of AA2024 compared to C11000, several different perforation geometries in the starting sheet were considered in order to more effectively distribute the plastic strain during stretch-bend fabrication. A T8 condition was selected over a T6 condition because it was shown that the plastic deformation induced during the final step was sufficient to enhance precipitation kinetics allowing higher strengths to be reached, while at the same time eliminating one annealing treatment. When hard anodizing treatments were conducted on O-temper and T8 temper AA2024 truss cores, the strength increase was different for different architectures, but was nearly the same for the two parent material tempers. Finally, the question of how much microtruss strengthening can be obtained for a given amount of parent metal strengthening was addressed by examining the interaction of material and geometric parameters in a model system. microtruss strengthening copper C11000 aluminum AA2024 cellular metal mechanical properties compressive strength densification energy modulus work hardening precipitation hardening heat treatment nanocrystalline coating aluminum oxide coating coating anodizing electrodeposition strengthening mechanisms geometry pyramidal compression buckling architecture truss uniaxial compression perforation Ramberg-Osgood Holloman nickel-iron annealing relative density periodic cellular hybrid composite microhardness stretch bend peak strength scanning electron microscopy stress strain bending stretching failure yielding column critical buckling strength critical buckling stress yield strength forming 0794
3	Strengthening Mechanisms in Microtruss Metals Ng, Evelyn 18 December 2012 (has links) Microtrusses are hybrid materials composed of a three-dimensional array of struts capable of efficiently transmitting an externally applied load. The strut connectivity of microtrusses enables them to behave in a stretch-dominated fashion, allowing higher specific strength and stiffness values to be reached than conventional metal foams. While much attention has been given to the optimization of microtruss architectures, little attention has been given to the strengthening mechanisms inside the materials that make up this architecture. This thesis examines strengthening mechanisms in aluminum alloy and copper alloy microtruss systems with and without a reinforcing structural coating. C11000 microtrusses were stretch-bend fabricated for the first time; varying internal truss angles were selected in order to study the accumulating effects of plastic deformation and it was found that the mechanical performance was significantly enhanced in the presence of work hardening with the peak strength increasing by a factor of three. The C11000 microtrusses could also be significantly reinforced with sleeves of electrodeposited nanocrystalline Ni-53wt%Fe. It was found that the strength increase from work hardening and electrodeposition were additive over the range of structures considered. The AA2024 system allowed the contribution of work hardening, precipitation hardening, and hard anodizing to be considered as interacting strengthening mechanisms. Because of the lower formability of AA2024 compared to C11000, several different perforation geometries in the starting sheet were considered in order to more effectively distribute the plastic strain during stretch-bend fabrication. A T8 condition was selected over a T6 condition because it was shown that the plastic deformation induced during the final step was sufficient to enhance precipitation kinetics allowing higher strengths to be reached, while at the same time eliminating one annealing treatment. When hard anodizing treatments were conducted on O-temper and T8 temper AA2024 truss cores, the strength increase was different for different architectures, but was nearly the same for the two parent material tempers. Finally, the question of how much microtruss strengthening can be obtained for a given amount of parent metal strengthening was addressed by examining the interaction of material and geometric parameters in a model system. microtruss strengthening copper C11000 aluminum AA2024 cellular metal mechanical properties compressive strength densification energy modulus work hardening precipitation hardening heat treatment nanocrystalline coating aluminum oxide coating coating anodizing electrodeposition strengthening mechanisms geometry pyramidal compression buckling architecture truss uniaxial compression perforation Ramberg-Osgood Holloman nickel-iron annealing relative density periodic cellular hybrid composite microhardness stretch bend peak strength scanning electron microscopy stress strain bending stretching failure yielding column critical buckling strength critical buckling stress yield strength forming 0794

1

Page generated in 0.1087 seconds