Global ETD Search

1	Strength Of Different Anatolian Sands In Wedge Shear, Triaxial Shear, And Shear Box Tests Erzin, Yusuf 01 January 2004 (has links) (PDF) Past studies on sands have shown that the shear strength measured in plane strain tests was higher than that measured in triaxial tests. It was observed that this difference changed with the friction angle &amp / #966 / cv at constant volume related to the mineralogical composition. In order to investigate the difference in strength measured in the wedge shear test, which approaches the plane strain condition, in the triaxial test, and in the shear box test, Anatolian sands were obtained from different locations in Turkey. Mineralogical analyses, identification tests, wedge shear tests (cylindrical wedge shear tests (cylwests) and prismatic wedge shear tests (priswests)), triaxial tests, and shear box tests were performed on these samples. In all shear tests, the shear strength measured was found to increase with the inclination &amp / #948 / of the shear plane to the bedding planes. Thus, cylwests (&amp / #948 / = 60o) iii yielded higher values of internal friction &amp / #966 / by about 3.6o than priswests (&amp / #948 / = 30o) under normal stresses between 17 kPa and 59 kPa. Values of &amp / #966 / measured in cylwests were about 1.08 times those measured in triaxial tests (&amp / #948 / &amp / #8776 / 65o), a figure close to the corresponding ratio of 1.13 found by past researchers between actual plane strain and triaxial test results. There was some indication that the difference between cylwest and triaxial test results increased with the &amp / #966 / cv value of the samples. With the smaller &amp / #948 / values (30o and 40o), priswests yielded nearly the same &amp / #966 / values as those obtained in triaxial tests under normal stresses between 20 kPa and 356 kPa. Shear box tests (&amp / #948 / =0o) yielded lower values of &amp / #966 / than cylwests (by about 7.9o), priswests (by about 4.4o), and triaxial tests (by about 4.2o) under normal stresses between 17 kPa and 48 kPa. It was shown that the shear strength measured in shear box tests showed an increase when &amp / #948 / was increased from 30o to 60o / this increase (about 4.2o) was of the order of the difference (about 3.6o) between priswest (&amp / #948 / = 30o) and cylwest (&amp / #948 / = 60o) results mentioned earlier. Shear box specimens with &amp / #948 / = 60o, prepared from the same batch of any sample as the corresponding cylwests, yielded &amp / #966 / values very close to those obtained in cylwests.
2	The Effects of Multi-Axial Loading on Adhesive Joints McFall, Bruce Daniel 01 June 2018 (has links) No description available. Mechanical Engineering Materials Science Industrial Engineering Transverse Compression Epoxy Carbon Fiber Laminate XFEM Shear Strength ABAQUS Double Strap Joint Brittle Ductile Ductile Peak Strength Fracture Mechanics T-Stress Multi-Axial Load
3	Strengthening Mechanisms in Microtruss Metals Ng, Evelyn 18 December 2012 (has links) Microtrusses are hybrid materials composed of a three-dimensional array of struts capable of efficiently transmitting an externally applied load. The strut connectivity of microtrusses enables them to behave in a stretch-dominated fashion, allowing higher specific strength and stiffness values to be reached than conventional metal foams. While much attention has been given to the optimization of microtruss architectures, little attention has been given to the strengthening mechanisms inside the materials that make up this architecture. This thesis examines strengthening mechanisms in aluminum alloy and copper alloy microtruss systems with and without a reinforcing structural coating. C11000 microtrusses were stretch-bend fabricated for the first time; varying internal truss angles were selected in order to study the accumulating effects of plastic deformation and it was found that the mechanical performance was significantly enhanced in the presence of work hardening with the peak strength increasing by a factor of three. The C11000 microtrusses could also be significantly reinforced with sleeves of electrodeposited nanocrystalline Ni-53wt%Fe. It was found that the strength increase from work hardening and electrodeposition were additive over the range of structures considered. The AA2024 system allowed the contribution of work hardening, precipitation hardening, and hard anodizing to be considered as interacting strengthening mechanisms. Because of the lower formability of AA2024 compared to C11000, several different perforation geometries in the starting sheet were considered in order to more effectively distribute the plastic strain during stretch-bend fabrication. A T8 condition was selected over a T6 condition because it was shown that the plastic deformation induced during the final step was sufficient to enhance precipitation kinetics allowing higher strengths to be reached, while at the same time eliminating one annealing treatment. When hard anodizing treatments were conducted on O-temper and T8 temper AA2024 truss cores, the strength increase was different for different architectures, but was nearly the same for the two parent material tempers. Finally, the question of how much microtruss strengthening can be obtained for a given amount of parent metal strengthening was addressed by examining the interaction of material and geometric parameters in a model system. microtruss strengthening copper C11000 aluminum AA2024 cellular metal mechanical properties compressive strength densification energy modulus work hardening precipitation hardening heat treatment nanocrystalline coating aluminum oxide coating coating anodizing electrodeposition strengthening mechanisms geometry pyramidal compression buckling architecture truss uniaxial compression perforation Ramberg-Osgood Holloman nickel-iron annealing relative density periodic cellular hybrid composite microhardness stretch bend peak strength scanning electron microscopy stress strain bending stretching failure yielding column critical buckling strength critical buckling stress yield strength forming 0794
4	Strengthening Mechanisms in Microtruss Metals Ng, Evelyn 18 December 2012 (has links) Microtrusses are hybrid materials composed of a three-dimensional array of struts capable of efficiently transmitting an externally applied load. The strut connectivity of microtrusses enables them to behave in a stretch-dominated fashion, allowing higher specific strength and stiffness values to be reached than conventional metal foams. While much attention has been given to the optimization of microtruss architectures, little attention has been given to the strengthening mechanisms inside the materials that make up this architecture. This thesis examines strengthening mechanisms in aluminum alloy and copper alloy microtruss systems with and without a reinforcing structural coating. C11000 microtrusses were stretch-bend fabricated for the first time; varying internal truss angles were selected in order to study the accumulating effects of plastic deformation and it was found that the mechanical performance was significantly enhanced in the presence of work hardening with the peak strength increasing by a factor of three. The C11000 microtrusses could also be significantly reinforced with sleeves of electrodeposited nanocrystalline Ni-53wt%Fe. It was found that the strength increase from work hardening and electrodeposition were additive over the range of structures considered. The AA2024 system allowed the contribution of work hardening, precipitation hardening, and hard anodizing to be considered as interacting strengthening mechanisms. Because of the lower formability of AA2024 compared to C11000, several different perforation geometries in the starting sheet were considered in order to more effectively distribute the plastic strain during stretch-bend fabrication. A T8 condition was selected over a T6 condition because it was shown that the plastic deformation induced during the final step was sufficient to enhance precipitation kinetics allowing higher strengths to be reached, while at the same time eliminating one annealing treatment. When hard anodizing treatments were conducted on O-temper and T8 temper AA2024 truss cores, the strength increase was different for different architectures, but was nearly the same for the two parent material tempers. Finally, the question of how much microtruss strengthening can be obtained for a given amount of parent metal strengthening was addressed by examining the interaction of material and geometric parameters in a model system. microtruss strengthening copper C11000 aluminum AA2024 cellular metal mechanical properties compressive strength densification energy modulus work hardening precipitation hardening heat treatment nanocrystalline coating aluminum oxide coating coating anodizing electrodeposition strengthening mechanisms geometry pyramidal compression buckling architecture truss uniaxial compression perforation Ramberg-Osgood Holloman nickel-iron annealing relative density periodic cellular hybrid composite microhardness stretch bend peak strength scanning electron microscopy stress strain bending stretching failure yielding column critical buckling strength critical buckling stress yield strength forming 0794
5	Gesteinsmechanische Versuche und petrophysikalische Untersuchungen – Laborergebnisse und numerische Simulationen Baumgarten, Lars 26 May 2016 (has links) (PDF) Dreiaxiale Druckprüfungen können als Einstufenversuche, als Mehrstufenversuche oder als Versuche mit kontinuierlichen Bruchzuständen ausgeführt werden. Bei der Anwendung der Mehrstufentechnik ergeben sich insbesondere Fragestellungen hinsichtlich der richtigen Wahl des Umschaltpunktes und des optimalen Verlaufs des Spannungspfades zwischen den einzelnen Versuchsstufen. Fraglich beim Versuch mit kontinuierlichen Bruchzuständen bleibt, ob im Versuchsverlauf tatsächlich Spannungszustände erfasst werden, welche die Höchstfestigkeit des untersuchten Materials repräsentieren. Die Dissertation greift diese Fragestellungen auf, ermöglicht den Einstieg in die beschriebene Thematik und schafft die Voraussetzungen, die zur Lösung der aufgeführten Problemstellungen notwendig sind. Auf der Grundlage einer umfangreichen Datenbasis gesteinsmechanischer und petrophysikalischer Kennwerte wurde ein numerisches Modell entwickelt, welches das Spannungs-Verformungs-, Festigkeits- und Bruchverhalten eines Sandsteins im direkten Zug- und im einaxialen Druckversuch sowie in dreiaxialen Druckprüfungen zufriedenstellend wiedergibt. Das Festigkeitsverhalten des entwickelten Modells wurde in Mehrstufentests mit unterschiedlichen Spannungspfaden analysiert und mit den entsprechenden Laborbefunden verglichen. Gesteinsprobe Prüfkörper Postaer Sandstein Laborprüfungen Petrophysikalische Untersuchungen Einaxialer Druckversuch Dreiaxialer Kompressionsversuch Einstufentest Mehrstufentechnik Spannungspfad Kontinuierliche Bruchzustände Continuous-Failure-State-Triaxial-Test Zugfestigkeitsprüfungen Scherversuch Spaltzugversuch Biegezugversuch Belastungsrichtung Ultraschalllaufzeitmessung Dehnwellen-Resonanzverfahren Kathodolumineszenz-Mikroskopie Gesteinkenngrößen Gesteinsmechanische Parameter Rohdichte Reindichte Porosität Dünnschliffanalyse Sphärizität Korngrößenverteilung Festigkeitskennwerte Höchstfestigkeit Spitzenfestigkeit Restfestigkeit Anisotropie Arbeitskurven Spannungs-Dehnungs-Verhalten Nachbruch Bruchbilder Verformungskennwerte Statischer Elastizitätsmodul Dynamischer Elastizitätsmodul Verformungsmodul Querdehnungszahl Impuls-Laufzeit Wellen-Ausbreitungsgeschwindigkeit Numerische Modellierung Simulationsrechnung PFC-3D Kugelmodell Clump Partikelarrangement Parameterkalibrierung Parallel Bond Mikrobruch Rissausbreitung elastische Wellen rock sample test specimen sandstone uniaxial compression test triaxial compression test unconfined compression test multiple failure state test continuous failure state test tensile splitting strength shear test bending test pulse velocity ultrasonic elastic constants Young’s modulus of elasticity modulus of deformation Poisson’s ratio post failure stress-strain behaviour real density apparent density grain-size distribution porosity flexural strength peak strength residual strength anisotropy fracture pattern micro-crack pulse-propagation velocity clump sphere model parallel bond crack propagation numerical modelling simulation elastic wave PFC-3D parameter calibration particle arrangement ddc:624 Posta Sandstein Gesteinsprobe Mechanische Eigenschaft Petrophysik Elastizität Werkstein Druckversuch Zugversuch Kennzahl Experiment Numerisches Modell
6	Gesteinsmechanische Versuche und petrophysikalische Untersuchungen – Laborergebnisse und numerische Simulationen Baumgarten, Lars 25 November 2015 (has links) Dreiaxiale Druckprüfungen können als Einstufenversuche, als Mehrstufenversuche oder als Versuche mit kontinuierlichen Bruchzuständen ausgeführt werden. Bei der Anwendung der Mehrstufentechnik ergeben sich insbesondere Fragestellungen hinsichtlich der richtigen Wahl des Umschaltpunktes und des optimalen Verlaufs des Spannungspfades zwischen den einzelnen Versuchsstufen. Fraglich beim Versuch mit kontinuierlichen Bruchzuständen bleibt, ob im Versuchsverlauf tatsächlich Spannungszustände erfasst werden, welche die Höchstfestigkeit des untersuchten Materials repräsentieren. Die Dissertation greift diese Fragestellungen auf, ermöglicht den Einstieg in die beschriebene Thematik und schafft die Voraussetzungen, die zur Lösung der aufgeführten Problemstellungen notwendig sind. Auf der Grundlage einer umfangreichen Datenbasis gesteinsmechanischer und petrophysikalischer Kennwerte wurde ein numerisches Modell entwickelt, welches das Spannungs-Verformungs-, Festigkeits- und Bruchverhalten eines Sandsteins im direkten Zug- und im einaxialen Druckversuch sowie in dreiaxialen Druckprüfungen zufriedenstellend wiedergibt. Das Festigkeitsverhalten des entwickelten Modells wurde in Mehrstufentests mit unterschiedlichen Spannungspfaden analysiert und mit den entsprechenden Laborbefunden verglichen. info:eu-repo/classification/ddc/624 ddc:624

1

Page generated in 0.0865 seconds