There are numerous techniques used to measure strain. Most are only capable of taking surface measurements. The penetrating nature of X-rays has been used to measure deformation, and thus strain, but only with radiographic images. Radioscopic techniques are faster and do not require film processing, but produce less detailed results than digitised radiographic images. The research covered by this thesis tested radioscopic images and showed them to be suitable for strain measurement. The thesis includes details of the design and capabilities of the radioscopic equipment. Pin cushion distortion is a common feature of radioscopic images, and an automatic method of identifying, and correcting for the distortion was implemented.

The purpose of this study is to find the design tool to create a soft tissue 3D model able to be used for finite element analysis to simulate the facial soft tissue deformation under g-loading and the helmet and mask/tissue interaction. Such a model will be of value in the design of new helmets and oxygen mask system, to reduce the effects of inertia, to provide improved fit, to minimise oxygen leakage especially when deformed under high g-loading. This work is concerned with the creation of a 3D geometric model. Further work may involve the measurement of mechanical properties of the facial soft tissue, finite element analysis and validation of the model. Using high frequency A-scan ultrasound allows the superficial tissue to be measured on volunteers without risk. The investigation covers 112 points on half of the face, linked to 11 defined morphological zones. The zonal boundaries are based on previous research and are initially identified by inspection and palpation of the face. There is large thickness range difference (30%) over the face in most zones defined in an individual. The iso-thickness zone hypothesis is not valid if the 'constant' thickness criterion is set to be 10% for all zones. Software algorithm for automatically detecting the facial soft tissue thickness is developed and validated to be effective (5% fail rate). Thickness data is acquired from European white males, females and Chinese males. The data collected in this study is also useful in forensic science for facial reconstruction purpose. Laser scanning method has been used to obtain the facial surface profile to create a surface model into which the soft tissue layer thickness distribution around the face can be incorporated. The surface model is exported in IGES format and can be imported in CAD software. Electromagnetic space locating method is used to acquire the ultrasound probe position so as to find the position of the tissue thickness. Point-based registration method is used to integrate the ultrasound thickness data into the laser scanned surface model to create a soft tissue shell solid model. The model is exported in IGES data format so that it can be imported into a finite element analysis package for further processing.

The aim of this work was to visualise heterogeneous deformation in snow under controlled laboratory conditions. Heterogeneous deformation was observed for both homogenous and heterogeneous loading conditions. Understanding deformation of snow is important in many scientific fields including vehicle traction, avalanche forecasting, and winter sports. This thesis investigates the deformation behaviour of snow on the centimetre scale under moderate strain rates (0.005 to 0.1 s-1) when subject to one-dimensional compression or to indentation. In order to allow controlled and repeatable snow deformation experiments, a new type of artificial snow was developed. This snow type was examined by low temperature scanning electron microscopy and by traditional avalanche observer’s methodology. Penetrometer experiments were conducted on the artificial snow and on natural seasonal snow in Scotland. The two snow types were found to be similar: results obtained on artificial snow are thus applicable to natural snow. A reproducible technique of manufacture and a thorough characterisation of the artificial snow are presented. One-dimensional compression experiments were conducted on the artificial snow. The experiments were in confined compression in a specially constructed apparatus, designed to provide for back-lit photography. Images were taken at 0.25 second intervals and analysed using digital image correlation, thus providing 2D strain fields. With careful control of photographic parameters, it is demonstrated that process of applying tracer substances to the snow is not necessary, thus allowing an unprecedented resolution. Spontaneously-forming strain localisations were observed for the first time, indicating strain softening behaviour. Damage was observed to propagate through the specimen as a moving front, resembling a wave. The force required to propagate the front remained nearly constant until the whole specimen was compacted, at which point a new front formed and the process repeated. The experimental method was extended to 2D indention experiments with a range of sizes and shapes of indenter. Complex deformation fields were observed, extending up to 6 times the width of the indenter on each side. Observed deformation included tensile tearing as well as compression and shear. The maximum local strain achieved in the indentation experiments was similar to that achieved by the first compaction front in one-dimensional compression. The work here presented has implications for snow deformation generally: strain localisation introduces a characteristic length, which may prevent scaling of models or results. The indentation results are particularly relevant to snow penetrometry, where indentation experiments are used to try and extract microstructural information from buried snow layers for the purpose of avalanche prediction. The common assumption that the penetrometer interacts only with snow very close to its tip may need to be reconsidered.

Kyoto University (京都大学) / 0048 / 新制・課程博士 / 博士(工学) / 甲第16815号 / 工博第3536号 / 新制||工||1535(附属図書館) / 29490 / 京都大学大学院工学研究科社会基盤工学専攻 / (主査)教授 松岡 俊文, 教授 小池 克明, 教授 田村 正行 / 学位規則第4条第1項該当

Autoclave processing of large scale, one-piece structural parts made of carbon fiber-reinforced polymer composite materials is the key to decreasing manufacturing costs while at the same time increasing quality. Nonetheless, even in manufacturing simple flat parts, residual strains and stresses are unavoidable. For structural design purposes and to aid in the assembly procedures, it is desirable to have proven numerical tools that can be used to predict these residual geometrical and material properties in advance, thus avoid the costly experimental trial and error methods. A 2-D finite element-based code, COMPRO, has previously been developed in-house for predicting autoclave process-induced deformations and residual stresses in composite parts undergoing an entire cure cycle. To simulate the tool-part interaction, an important source of residual deformations/stresses, COMPRO used a non-zero thickness elastic shear layer as its only interface option. Moreover, the code did not account for the large deformations and strains and the resulting nonlinear effects that can arise during the early stages of the cure cycle when the material is rather compliant. In the present work, a contact surface employing a penalty method formulation is introduced at the tool-part interface. Its material-dependent parameters are a function of temperature, degree of cure, pressure and so forth. This makes the stick-slip condition plus separation between the part and the tool possible. The large displacements/rotations and large shear strains that develop at the early stages of the cure cycle when the resin has a very low elastic modulus provided the impetus to include a large strain/deformation option in COMPRO. A new “co-rotational stress formulation” was developed and found to provide a robust method for numerical treatment of very large deformation/strain problems involving anisotropic materials of interest here. Several verification and validation examples are used to calibrate the contact interface parameters and to demonstrate the correctness of implementation and the accuracy of the proposed method. A number of comparisons are made with exact solutions, other methods, other experiments and the same models in other commercial codes. Finally, several interesting cases are examined to explore the results of COMPRO predictions with the added options. / Applied Science, Faculty of / Civil Engineering, Department of / Graduate

The existence of highest proton numbers at which the nuclear landscape cease to ex- ist, the end of the periodic table of elements and the limits of the existence of the nu- clei are some of the difficult questions to answer. To explore those questions, we in- vestigated hyperheavy nuclei (Z ≥ 126) using covariant density functional theory. We demonstrate the existence of three regions of spherical hyperheavy nuclei centered around (Z ∼ 138, N ∼ 230), (Z ∼ 156, N ∼ 310) and (Z ∼ 174, N ∼ 410). Also, we explored other properties of hyperheavy nuclei such as octupole deformation, alpha decay half lives, chemical potential, etc.

No description available.

Microfluidics is the science of processing microliters or less of fluid at a time in a channel with dimensions on the order of microns. The small size of the channels allows fluid properties to be studied in a world dominated by viscosity, surface tension, and diffusion rather than gravity and inertia. Microfluidic droplet generation is a well studied and understood phenomena, which has attracted attention due to its potential applications in biology, medicine, chemistry and a wide range of industries. This dissertation adds to the field of microfluidic droplet studies by studying individual droplet deformation and the process of scaling-up microfluidic devices for industrial use. The study of droplet deformation under extensional and mixed shear and extensional flows was performed within a microfluidic device. Droplets were generated using a flow-focusing device and then sent through a hyperbolic contraction downstream of the droplet generator. The hyperbolic contraction allowed the smallest droplets to be deformed by purely extensional flows and for the larger droplets to experience mixed extensional and shear flows. The shear resulted from the proximity of the droplet to the walls of the microfluidic channel. The continuous phase in all of these devices was oil and the dispersed phase was water, an aqueous surfactant solution, or an aqueous suspension of colloidal particles. Droplet deformation dynamics are affected by the use of surfactants and colloidal particles, which are commonly used to stabilize emulsion droplets again coalescence. Microfluidic droplet generating devices have many potential industrial applications, however, due to the low output of product from a single droplet generating device, their potential has not been realized. Using six parallel flow-focusing droplet generators on a single chip, the process of microfluidic droplet formation can be scaled up, thus resulting in a higher output of droplets. The tuning of droplet size and production frequency can be achieved on chip by varying the outlet tubing lengths, thus allowing for a single device to be used to generate a range of droplet sizes.

<p> Orientations of deformation lamellae in quartz and C-axes of quartz grains containing lamellae were measured at seven locations across a gently folded bed of the Oriskany Sandstone, central Pennsylvania. Lamellae so measured have an average inclination of 20°-30° to the basal plane, and are therefore categorized as "subbasal".</p> <p> Fabrics of poles to deformation lamellae and corresponding C-axis orientations suggest a paleostress field for the fold which had the arrangement; σ1 bedding parallel, σ3 bedding perpendicular, and σ2 fold axis subparallel. Relative magnitudes of the stresses were given by the condition σ1 > σ3. σ2 is believed to have varied in magnitude between σ1 and σ3 during fold development.</p> <p> Exact timing of formation of lamellae is uncertain. Textural evidence shows that they predate a later generation of compressional and tensional microfractures associated with the deformation. The best explanation is that they formed in early stages of layer parallel compaction when compressive stresses in all zones of the fold were greatest. Stress refraction may or may not have been operative.</p> / Thesis / Bachelor of Science (BSc)

Toward support of the use of geometry in advanced simulation, a freeorm deformation (FFD) tool was designed, developed, and tested using object oriented (OO) techniques. The motivation for creating this FFD tool in-house was to provide engineers and researchers a cost efficient, quick, and easy way to computationally manipulate models without having to start from scratch while readily seeing the resulting geometry. The FFD tool was built using the OO scripting language, Python, the OO GUI toolkit, Qt, and the graphics toolkit, OpenGL. The tool produced robust and intuitive results for two-dimensional shapes especially when multiple point manipulation was utilized. The use of ?grouping? control points also provided the user the ability to maintain certain desired shape features such as straight lines and corners. This in-house FFD tool could be useful to engineers due to the ability to customize source code.