As claudicações são a principal causa de encaminhamento de equinos aos médicos veterinários e uma das maiores causas de encaminhamento destes animais aos hospitais de referência; sendo as fraturas, especialmente aquelas de ossos longos e articulares, as que têm menor índice de sucesso devido ao prognóstico reservado e alto custo do tratamento; entendendo como sucesso o retorno do animal à função ou manutenção da qualidade de vida. A articulação interfalangeana proximal (AIP) dos equinos é clinicamente importante devido à apresentação frequente de claudicação, com lesões que comprometem a vida esportiva e função do equino. O objetivo desta pesquisa foi comparar biomecanicamente as características de duas técnicas de artrodese da AIP em equinos, utilizando-se placa de compressão dinâmica (DCP) de 4.5mm e três orifícios em combinação com dois parafusos corticais transarticulares de 5.5mm oblíquos inseridos pela técnica de tração (lag screw) e placa em "Y\" de compressão bloqueada (LCP) de 5,0mm e sete orifícios, com parafusos bloquados unicorticais e um parafuso cortical de 4.5mm oblíquo transarticular inserido no orifício central da placa, pela técnica de parafuso de tração. Foram utilizadas doze peças anatômicas de membros anteriores de equinos, das quais foi isolada a porção distal do membro desde a primeira falange até o casco. Uma vez preparadas as peças, cada par foi sorteado randomicamente para cada um dos dois grupos. Os modelos experimentais foram submetidos a ensaios biomecânicos de compressão axial em ciclo único até a sua falha. O tipo de falha ocorrida na placa, nos parafusos ou nos ossos foi avaliado, assim como a força à qual ocorreram estas falhas. Não houve diferença estatística significativa entre os grupos DCP e Y-LCP, nas variáveis rigidez e força máxima, quando submetidas a compressão axial até sua falha. Mesmo não havendo diferença entre as duas técnicas cirúrgicas na variável rigidez, a técnica Y-LCP possibilitou um procedimento menos invasivo e com menor tempo cirúrgico. Conclui-se que, as propriedades biomecânicas das duas técnicas de fixação (DCP e Y-LCP) são semelhantes nas condições testadas. / Lameness is the main cause of sport horses\' owners consulting equine veterinarians and one of the highest cause to send these animals to the reference hospitals. Long bones and joint fractures have the lesser rate of success, consequence of the hight cost of the treatment and poor prognosis. Understanding as success the return of the horse to previous athletic performance or at least to have useful life. The proximal interphalangeal joint (PIPJ) is clinically important because the injuries that involve it may threaten the horses sport life or its usefulness. The objective of this study was to compare the biomechanical properties of two PIPJ arthrodesis techniques using 4.5mm dynamic compression plate (DCP) in conjunction with two oblique abaxial transarticular 5.5mm cortical screws inserted in lag fashion and 5.0mm Y locking compression plate (Y-LCP) with unicortical locking screws and one axial transarticular 4.5mm cortex screw inserted in lag fashion through the midle plate hole. It was used twelve cadaveric adult equine forelimbs from the first phalanx to the foot. After full-limb preparations, each forelimb pair was randomly assigned to one of two treatment groups. Constructs were submited to axial compression single cycle to failure biomechanical testing. The failure of the screws, plate or bone, and the force at wich it happened was evaluated. There were no significant differences in construct stiffness or max force when loaded to failure, between the DCP and Y-LCP treatment groups. Even though there was no construct stiffness diffrences between the two techniques, the Y-LCP technique provided the possibility of a less invasive procedure with a shorter surgical time. In conclusion, the biomechanical properties of both fixation techniques (DCP and Y-LCP) are equivalent under the test conditions used.

O propósito principal do presente trabalho é estabelecer diretrizes para o uso de elementos finitos sólidos na modelagem de estruturas delgadas submetidas à flexão. Por meio de um conjunto de problemas estudou-se o travamento de elementos finitos da elasticidade bi e tridimensionais, quando usados para modelar estruturas delgadas submetidas à flexão. Foram usados elementos planos de 4, 8 e 9 nós e elementos tridimensionais de 4, 10, 11, 8, 20 e 27 nós, considerando elementos não distorcidos e distorcidos. A análise dos resultados nesses modelos permitiram entender melhor o comportamento e o uso de elementos sólidos em estruturas delgadas. / The main objective of the present work is to establish guidelines for the use of solid finite elements in the modeling of thin structures submitted to bending. By means of a set of problems the locking of elements three-dimensional and two-dimensional elasticity was studied, when used to model problems thin structures subjected to bending. We use 2-D displacements-based elements of 4, 8 and 9 nodes and 3-D displacement based of 4, 10, 11, 8, 20 and 27 nodes, considering undistorted and distorted elements. The analysis of the results of these models lead to the understanding of the behavior and the use of solid elements in thin structures.

A utilização de placas bloqueadas e suas vantagens biomecânicas na redução de fraturas cominutivas de ossos longos em cães já foram descritas por diversos autores. O presente trabalho teve como objetivo avaliar diferentes configurações de placa bloqueadas submetidas a dois diferentes testes biomecânicos, um de flexão em quatro pontos para avaliar a influencia do preenchimento dos orifícios centrais na resistência a flexão da placa bloqueada com função de placa de apoio. O outro teste avaliou a força máxima ao arrancamento de dois diferentes tipos de placas, um com todos os orifícios perpendiculares e outro com os orifícios angulados alternadamente lateral e medialmente em relação ao eixo longitudinal da placa. Para cada teste formou-se dois grupos com dez corpos de prova cada. Não houve diferença estatística no resultado obtido no teste de flexão, a resistência a flexão do grupo com preenchimentos dos orifícios centrais foi maior em relação ao grupo sem preenchimento, porem sem significância. Já no teste de arrancamento o grupo de placas com orifícios angulados obteve um valor de forma máxima de arrancamento significantemente superior em relação ao grupo com orifícios perpendiculares em relação ao eixo longitudinal da placa. Concluiu-se que não há influencia na resistência da placa de apoio com o preenchimento dos orifícios centrais da placa bloqueada e que a configuração de placa com os orifícios angulados se mostrou mais resistente ao arrancamento. / The feasibility of locking plates and their biomechanical advantages in comminuted fractures are well known. The objective of this study was to evaluate different locking plate´s configurations submitted to a four point´s flexion test and pull out test. The flexion test evaluated the influence of screws in center position in bridging plate, the pull out test compared relative to pull out strength locking plates using parallel locking screws or angulated locking screws. For each biomechanical assay two groups of ten test materials were formed. The results found no statistical differences relative to flexion resistance in the groups with and without central screws. Relative to pull out test the group with angulated screws showed higher values of maximum pull out strength when compared with the perpendicular screws, the data were statistically significant. We concluded that there was no improvement in the resistance of bridging plate with the use of central screws, but the use of angulated screws showed a greater resistance to pull out when compared to parallel screws.

Proximal humerus fractures are the third most common fractures in the over-65 patient population and their stable fixation remains a key challenge in orthopaedic and trauma surgery. While Open Reduction Internal Fixation by plate has become a well-known treatment modality in the last few decades, clinical studies associate high complication rate with its use. The overall aim of this project was to create a computer-aided design framework for proximal humerus plates using a validated subject-specific humerus-plate finite element model. The framework consisted of three stages: (1) reverse engineering of bone and plate geometry, (2) creation and validation of a finite element model simulating the in vitro testing of the bone-implant construct and (3) parametric optimisation study of implant design using this model. In vitro biomechanical tests were conducted to not only compare the mechanical performance of three key commercially available proximal humerus plates (S3-, Fx- and PHILOS plate) but also the effect of different screw zones. Sixty-five humeri specimens with two-part surgical neck fractures were treated and grouped based on their different screw configurations. Extension, flexion, varus and valgus bending were applied in the cantilever fashion in the elastic tests whereas only varus bending was applied in the plastic tests. The load required to apply 5 mm displacement was measured to determine bone-plate construct stiffness. The S3 plate yielded the stiffest constructs and while the removal of the inferomedial support had the most impact on varus bending stiffness, type of medial support was important: inferomedial screws in the Fx plate achieved higher bending stiffness than blade insertion. Stability of constructs treated with the plate was an interplay of factors such as the plate’s and screws' number, orientation and position. Next, a subject-specific finite element model of the humerus-plate construct was successfully developed that simulated the stiffest of the constructs from the in vitro varus bending tests conducted in this project. The model was validated against the in vitro results. The validated model was then used to perform a parametric optimisation study where the combination of design parameters (height and divergence angle of S3 plate’s inferomedial screws) was determined that achieved optimum bone-plate construct stability (minimum fracture gap change). Out of the 538 designs tested, the optimum design (16o divergence angle and 33o height angle) yielded the lowest fracture gap change (0.156 mm) which was 4.686% lower than the standard finite element model while achieving 5.707% higher varus bending load (54.753 N). The validated model was also used to investigate the issue of using smooth pegs and threaded screws. Twenty-six models with different percentages of screw threading were run to compare their bone-plate construct stiffness. While threading the smooth pegs was found to increase the varus bending stiffness by up to 4.546%, it did not affect all screws equally. Finally, the successful completion of the optimisation study of screw orientation and the clinical investigation promises the implementation of the computational framework for a range of future multi-objective optimisation studies of multiple design parameters especially for the design of implants for other parts of the human body and also for investigations into other clinically relevant questions.

A utilização de placas bloqueadas e suas vantagens biomecânicas na redução de fraturas cominutivas de ossos longos em cães já foram descritas por diversos autores. O presente trabalho teve como objetivo avaliar diferentes configurações de placa bloqueadas submetidas a dois diferentes testes biomecânicos, um de flexão em quatro pontos para avaliar a influencia do preenchimento dos orifícios centrais na resistência a flexão da placa bloqueada com função de placa de apoio. O outro teste avaliou a força máxima ao arrancamento de dois diferentes tipos de placas, um com todos os orifícios perpendiculares e outro com os orifícios angulados alternadamente lateral e medialmente em relação ao eixo longitudinal da placa. Para cada teste formou-se dois grupos com dez corpos de prova cada. Não houve diferença estatística no resultado obtido no teste de flexão, a resistência a flexão do grupo com preenchimentos dos orifícios centrais foi maior em relação ao grupo sem preenchimento, porem sem significância. Já no teste de arrancamento o grupo de placas com orifícios angulados obteve um valor de forma máxima de arrancamento significantemente superior em relação ao grupo com orifícios perpendiculares em relação ao eixo longitudinal da placa. Concluiu-se que não há influencia na resistência da placa de apoio com o preenchimento dos orifícios centrais da placa bloqueada e que a configuração de placa com os orifícios angulados se mostrou mais resistente ao arrancamento. / The feasibility of locking plates and their biomechanical advantages in comminuted fractures are well known. The objective of this study was to evaluate different locking plate´s configurations submitted to a four point´s flexion test and pull out test. The flexion test evaluated the influence of screws in center position in bridging plate, the pull out test compared relative to pull out strength locking plates using parallel locking screws or angulated locking screws. For each biomechanical assay two groups of ten test materials were formed. The results found no statistical differences relative to flexion resistance in the groups with and without central screws. Relative to pull out test the group with angulated screws showed higher values of maximum pull out strength when compared with the perpendicular screws, the data were statistically significant. We concluded that there was no improvement in the resistance of bridging plate with the use of central screws, but the use of angulated screws showed a greater resistance to pull out when compared to parallel screws.

The design of high-performance, high-speed clock generation and distribution becomes challenging in terms of phase noise, jitter and power consumption, due to the fast development of communication and computing systems. Injection locking is a promising clocking technique since it can significantly improve the energy efficiency, suppress the phase noise of the ring oscillator, enable a fast startup and conveniently generate multiple time-interleaved phases. A quasi-linear model of injection-locked ring oscillator (ILRO) is utilized to mathematically formulate the frequency and time domain characteristics of the system, as well as the phase noise shaping and jitter tracking behavior. The settling behavior of ILRO is also exploited and shows a strong dependence on the locking range and the initial phase difference of the injected and the resultant oscillation signals. A forwarded-clock synchronization based on injection locking is designed for a 10 Gb/s photonic interconnect according to the specific features of optical links. A single clock recovery can be used for all the four channels, resulting in a large amount of power and area saving. The applications of sub-harmonic and super-harmonic injection locking in wireless communications for frequency multiplying and division are also discussed. / Graduation date: 2013 / Access restricted to the OSU Community at author's request from Oct. 1, 2012 - Oct. 1, 2014

The primary objective of this work was to develop a laser source for fundamental investigations in the field of laser – materials interactions. In particular it is supposed to facilitate the study of the influence of the temporal energy distribution such as the interaction between adjacent pulses on ablation processes. Therefore, the aim was to design a laser with a highly flexible and easily controllable temporal energy distribution. The laser to meet these demands is an SBS-laser with optional active mode-locking. The nonlinear reflectivity of the SBS-mirror leads to a passive Q-switching and issues ns-pulse bursts with µs spacing. The pulse train parameters such as pulse duration, pulse spacing, pulse energy and number of pulses within a burst can be individually adjusted by tuning the pump parameters and the starting conditions for the laser. Another feature of the SBS-reflection is phase conjugation, which leads to an excellent beam quality thanks to the compensation of phase distortions. Transverse fundamental mode operation and a beam quality better than 1.4 times diffraction limited can be maintained for average output powers of up to 10 W. In addition to the dynamics on a ns-timescale described above, a defined splitting up of each ns-pulse into a train of ps-pulses can be achieved by additional active mode-locking. This twofold temporal focussing of the intensity leads to single pulse energies of up to 2 mJ at pulse durations of approximately 400 ps which corresponds to a pulse peak power of 5 MW. While the pulse duration is of the same order of magnitude as those of other passively Q-switched lasers with simultaneous mode-locking, the pulse energy and pulse peak power exceeds the values of these systems found in the literature by an order of magnitude. To the best of my knowledge the laser presented here is the first implementation of a self-starting mode-locked SBS-laser oscillator. In order to gain a better understanding and control of the transient output of the laser two complementary numerical models were developed. The first is based on laser rate equations which are solved for each laser mode individually while the mode-locking dynamics are calculated from the resultant transient spectrum. The rate equations consider the mean photon densities in the resonator, therefore the propagation of the light inside the resonator is not properly displayed. The second model, in contrast, introduces a spatial resolution of the resonator and hence the propagation inside the resonator can more accurately be considered. Consequently, a mismatch between the loss modulation frequency and the resonator round trip time can be conceived. The model calculates all dynamics in the time domain and therefore the spectral influences such as the Stokes-shift have to be neglected. Both models achieve an excellent reproduction of the ns-dynamics that are generated by the SBS-Q-switch. Separately, each model fails to reproduce all aspects of the ps-dynamics of the SBS-laser in detail. This can be attributed to the complexity of the numerous physical processes involved in this system. But thanks to their complementary nature they provide a very useful tool for investigating the various influences on the dynamics of the mode-locked SBS-laser individually. These aspects can eventually be recomposed to give a complete picture of the mechanisms which govern the output dynamics. Among the aspects under scrutiny were in particular the start resonator quality which determines the starting condition for the SBS-Q-switch, the modulation depth of the AOM and the phonon lifetime as well as the Brillouin-frequency of the SBS-medium. The numerical simulations and the experiments have opened several doors inviting further investigations and promising a potential for further improvement of the experimental results: The results of the simulations in combination with the experimental results which determined the starting conditions for the simulations leave no doubt that the bandwidth generation can primarily be attributed to the SBS-Stokes-shift during the buildup of the Q-switch pulse. For each resonator round trip, bandwidth is generated by shifting a part of the revolving light in frequency. The magnitude of the frequency shift corresponds to the Brillouin-frequency which is a constant of the SBS material and amounts in the case of SF6 to 240 MHz. The modulation of the AOM merely provides an exchange of population between spectrally adjacent modes and therefore diminishes a modulation in the spectrum. By use of a material with a Brillouin-frequency in the GHz range the bandwidth generation can be considerably accelerated thereby shortening the pulse duration. Also, it was demonstrated that yet another nonlinear effect of the SBS can be exploited: If the phonon lifetime is short compared to the resonator round trip time we obtain a modulation in the SBS-reflectivity that supports the modulation of the AOM. The application of an external optical feedback by a conventional mirror turns out to be an alternative to the AOM in synchronizing the longitudinal resonator modes. The interesting feature about this system is that it is ― although highly complex in the physical processes and the temporal output dynamics ― very simple and inexpensive from a technical point of view. No expensive modulators and no control electronics are necessary. Finally, the numerical models constitute a powerful tool for the investigation of emission dynamics of complex laser systems on arbitrary timescales and can also display the spectral evolution of the laser output. In particular it could be demonstrated that differences in the results of the complementary models vanish for systems of lesser complexity. / Ziel der Arbeit ist die Entwicklung einer Laserstrahlquelle, die zur Untersuchung von Laser-Material-Wechselwirkungen eingesetzt werden soll. Im Mittelpunkt des Interesses steht hierbei der Einfluss der zeitlichen Pulsstruktur des Lasers auf Materialabtragsprozesse. Daraus ergibt sich die Anforderung einer möglichst hohen Flexibilität in der Pulsstruktur des Lasers sowie einer möglichst guten Strahlqualität. Eine gute Strahlqualität zeichnet sich durch eine homogene räumliche Intensitätsverteilung aus und ist Voraussetzung für eine gezielte Energiedeponierung auf dem Material. Diese Anforderungen wurden mit einem SBS-Laser erfüllt. Dabei handelt es sich um einen Laser, der einen SBS-Spiegel verwendet, dessen Reflektivität auf der Streuung des Lichts an Schallwellen beruht, die von dem einfallenden Licht selbst erzeugt werden. Als Resultat hat dieser Spiegel eine Reflektivität, die abhängig von der Energie des eingestrahlten Lichts ist. In einem Laser verwendet führt diese energieabhängige Reflektivität zu einer sogenannten Güteschaltung, die sich in der Ausbildung von kurzen Lichtpulsen mit Dauern von etwa 100 Nanosekunden äußert. Die Abstände zwischen den Pulsen, die Pulsdauern und die Pulsenergien können sehr leicht durch die Randbedingungen, wie etwa die Reflektivität der konventionellen Spiegel des Lasers, gesteuert werden. Durch eine zusätzliche, aktiv herbeigeführte Verlustmodulation im Laserresonator wird eine Aufspaltung der Nanosekundenpulse in eine Reihe von Pulsen mit Dauern von nur noch einigen 100 Pikosekunden erreicht. Diese Technik ist unter dem Begriff Modenkopplung bekannt. Es liegt jetzt also eine doppelte Pulsstruktur vor: Nanosekundenpulse, die sich jeweils aus vielen Pikosekundenpulsen zusammensetzen. Durch diese doppelte zeitliche Bündelung der Ausgangsleistung werden während der Pulse Spitzenleistungen von bis zu 5 MW erreicht. Die Pulsenergien der ps-Pulse erreichen bis zu 2 mJ. Diese Werte liegen um den Faktor 10 über denen vergleichbarer Systeme. Meines Wissens ist dies die erste Umsetzung eines selbsttätigen SBS-Lasers mit zusätzlicher Modenkopplung. Um die verschiedenen Einflüsse auf diese Emissionsdynamik besser verstehen und kontrollieren zu können, wurden zwei Modelle mit komplementären Ansätzen entwickelt, auf deren Basis diese Dynamik durch numerische Simulationen wiedergegeben werden kann. Insbesondere können auf diese Weise auch die Einflüsse von einzelnen Materialparametern isoliert betrachtet werden, was im Experiment im allgemeinen nicht möglich ist. Der SBS-Laser wurde bereits erfolgreich in Laser-Materialbearbeitungsexperimenten eingesetzt. So konnte beispielsweise gezeigt werden, dass sich die Bearbeitungsdauer beim Wendelbohren durch die Verwendung von Pulszügen, also einer Reihe kurz aufeinander folgender Pulse, gegenüber dem Einsatz von Pulsen mit gleichmäßigen Abständen erheblich verbessern lässt.

This thesis is devoted to the numerical analysis of mesh-free methods and, in particular, to the study of the possible advantages of the EFG (Element Free Galerkin) mesh-free method against the well-known FE (Finite Element) method. More precisely, the EFG method and the FE method behavior are compared in two particular interesting problems: (1) analysis of volumetric locking in mechanical problems and (2) accurate resolution of transient convection dominated problems. In both cases the good properties and possibilities of mesh-free methods become apparent. However, in several situations the FE method is still more competitive: for instance, the computation of the FE shape functions and its integrals are less costly, and essential boundary conditions can be easily imposed. Thus, in order to take advantage of the good properties of both methods, a mixed interpolation combining FE and EFG is proposed. This formulation can be applied in two useful situations: (i) enrichment of finite elements with EFG, and (ii) coupling of FE and EFG. An a priori error estimate for the first one is presented and proved. Several examples show the applicability of the mixed interpolation in adaptive computations. / Aquesta tesi està dedicada a l'anàlisi numèrica dels mètodes sense malla i, en particular, a l'estudi dels possibles avantatges del mètode EFG (Element Free Galerkin) davant del ben conegut MEF (Mètode dels Elements Finits). Concretament, es comparen el mètode EFG i el MEF en dos problemes concrets d'interès: (1) l'anàlisi del bloqueig volumètric en problemes mecànics i (2) la resolució precisa de problemes transitoris amb convecció dominant. Les bones propietats i possibilitats dels mètodes sense malla es fan evidents en tots dos casos.Tot i així, en varis aspectes el MEF resulta més competitiu: per exemple, el càlcul de les funcions de forma i de les seves integrals es menys costós, i les condicions de contorn essencials es poden imposar fàcilment. Amb l'objectiu d'aprofitar les bones qualitats dels dos mètodes, es proposa una interpolació mixta combinant elements finits y EFG, aplicable en dues situacions: (i) enriquiment d'elements finits amb EFG i (ii) acoblament d'elements finits i EFG. Per al primer cas, es presenta i demostra una cota a priori de l'error. L'aplicabilitat d'aquesta interpolació mixta en processos adaptatius es mostra amb varis exemples. / Esta tesis está dedicada al análisis numérico de los métodos sin malla y, en particular, al estudio de las posibles ventajas del método EFG (Element Free Galerkin) frente al bien conocido MEF (Método de los Elementos Finitos). Concretamente, se comparan el método EFG y el MEF en dos problemas concretos de interés: (1) el análisis del bloqueo volumétrico en problemas mecánicos y (2) la resolución precisa de problemas transitorios con convección dominante. Las buenas propiedades y posibilidades de los métodos sin malla se hacen evidentes en ambos casos.Sin embargo, en varios aspectos el MEF resulta más competitivo: por ejemplo, el cálculo de las funciones de forma y sus integrales es menos costoso, y las condiciones de contorno esenciales se pueden imponer fácilmente. Con el objetivo de aprovechar las buenas cualidades de ambos métodos, se propone una interpolación mixta combinando elementos finitos y EFG, aplicable en dos situaciones: (i) enriquecimiento de elementos finitos con EFG, y (ii) acoplamiento de elementos finitos y EFG. Para el primer caso, se presenta y demuestra una cota a priori del error. La aplicabilidad de esta interpolación mixta en procesos adaptativos se muestra con varios ejemplos.

I denna rapport redogör projektgruppen för resultatet i kursen examensarbete 15hp (C-nivå) utfört på maskiningenjörsprogrammet, inriktning produktutveckling och design, vid Jönköpings Tekniska Högskola. Examensarbetet har utförts i samarbete med Kongsberg Power Product Systems AB i Ljungsarp. Syftet var att utveckla en ny typ av övre teleskopfunktion till Kongsbergs modulsystem för ställbara rattstänger. Utgångspunkten i projektet var att skapa en mer ergonomisk förarmiljö, något som Kongsbergs kunder och marknaden för långsamtgående fordon allt mer efterfrågar. Kraven som ställts på projektet bestod i största del av axiella och radiella krafter som konstruktionen skulle klara av, samt den axiella förlängningen av rattstången. För att strukturera arbetet har en produktutvecklingsmetod från boken The Mechanical Design Process av David G. Ullman använts. Dessa metoder har använts i genomförandefasen för att leda fram till resultatet. Projektet har resulterat i ett koncept som löser Kongsbergs krav på förbättrad förarergonomi. / In this report the project team describes the outcome of the course degree project 15 ECTS (C level) performed at the program of mechanical engineering, targeted product development and design, at Jönköping University. The degree project has been carried out in cooperation with Kongsberg Power Products Systems AB in Ljungsarp. The aim was to develop a new type of upper telescopic function to the Kongsberg modular system for adjustable steering columns. The starting point of the project was to create a more ergonomic driver's environment, as Kongsberg’s customers and the market for slow vehicles are increasingly demanding. The requirements placed on the project consisted in the main part of the forces that construction would meet, and the axial extension of the steering column. To structure the work a product development methodology from the book The Mechanical Design Process by David G. Ullman has been used. The project has resulted in a concept that solves Kongsberg's demands for improved driver ergonomics.

We report on initial research on the concurrency control issue of compiled database applications. Such applications have a repository style of architecture in which a collection of software modules operate on a common database in terms of a set of predefined transaction types, an architectural view that is useful for the deployment of database technology to embedded control programs. We focus on decoupling concurrency control from any functionality relating to recovery. Such decoupling facilitates the compile-time query optimization. <br /><br /> Because it is the possibility of transaction aborts for deadlock resolution that makes the recovery subsystem necessary, we choose the deadlock-free tree locking (TL) scheme for our purpose. With the knowledge of transaction workload, efficacious lock trees for runtime control can be determined at compile-time. We have designed compile-time algorithms to generate the lock tree and other relevant data structures, and runtime locking/unlocking algorithms based on such structures. We have further explored how to insert the lock steps into the transaction types at compile time. <br /><br /> To conduct our simulation experiments to evaluate the performance of TL, we have designed two workloads. The first one is from the OLTP benchmark TPC-C. The second is from the open-source operating system MINIX. Our experimental results show TL produces better throughput than the traditional two-phase locking (2PL) when the transactions are write-only; and for main-memory data, TL performs comparably to 2PL even in workloads with many reads.