No description available.

No description available.

The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding. An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage. A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner. A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.   The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction. / civilingenjörsexamen

Nous ne sommes plus à l’âge où les destructions poétiques d’appareils se voient car les régimes d’appareils sont devenus transparents : lorsque nous pressons un écran tactile, nous touchons ce que nous ne voyons plus, nos empreintes, et nous voyons ce que nous ne toucherons jamais, le plan numérique. Pour l’artiste contemporain, l’interface haptique – point d’orgue d’une technologie stéréotypée de la percussion – est le parergon d’une échelle inédite, toute tactile. De la machine à écrire aux claviers de plus en plus fins du design informatique, à mesure que l’on croit voir le bloc imaginaire céder sous la pression ergonomique de l’empire cybernétique, se palpe en fait un réel d’emblée en dehors des formes et à l’intérieur de notre doigté. C’est l’espace de la corne aux doigts. Ce transfert, cette remontée du point d’impact dans son élan, ce retour de la forme dans sa structure font du moment de touche – de l’appareillage comme manœuvre de départ – un isolat capital pour reposer la question de la sculpture à l’époque des immatériaux. Bien en face et à contre-courant de la surface informatique, une épaisseur sensible fonctionnelle aurait lieu et pourrait donc faire œuvre ; telle est la thèse proposée ici. Le comportement machinal de l’utilisateur d’interfaces sera considéré comme un modèle poïétique ou pensé comme une partie de l’imagination en attente de traduction plastique. Pendant que se joue l’expérience rythmique de l’interactivité, le corps ne doit-il pas fournir un effort perceptif pour ne pas s’absenter dans une partition photo-digitale jouée par avance ? Ne doit-il pas exprimer son ancrage particulier, calleux et bruissant – nous l’appellerons dactylo-phonique – au contact de la matière du monde ? Sans cette expression, jamais le design technologique contemporain, bi ou tridimensionnel, modélisé et assisté par ordinateur, n’entamera de rapport véritablement efficient avec le réel de nos habitudes et de nos démarches ; bref avec tout le poids incarné de notre conscience imageante : la perte d’indicialité instaurerait-elle un type introverti de phénoménalité ? / Poetic destructions of apparatus are no longer visible as regimes of apparatus have become transparent: when we press a tactile screen, we touch what we cannot see anymore – our fingerprints – and we see what we will never be able to touch – the digital space. For contemporary artists, haptic interfaces are the finger-tipping point of a technological dynamics of percussion but also the parergon of a new and entirely tactile scale. From the first typewriters to the latest ultra thin keyboards designed by computer manufacturers, we may think imagination is yielding under the ergonomic pressure of the cybernetic world. But in fact, existing outside of the shapes and right under our fingertips lies a palpable reality – the space of calluses. This transfer, this sensory feedback, this return of the form to its structure turns this casting off of the apparatus into an essential isolate to rethink sculpture in the age of immateriality. Right in front of the computer surface but working against it, there would be a functional sensitive thickness – an art-making place. This is our thesis. The machine-like behaviour of the interface user will be considered as a poietic model or regarded as a part of imagination waiting for plastic translation.We may wonder whether the rhythmic experience of interactivity does not entail a perceptual bodily effort on our side in order not to remain absent during the performance of a somewhat predictable photo-digital score.Doesn't this peculiar, callous and rustling – or dactylo-phonic – anchoring of the body to the substance of the world need to express itself? Without this expression, contemporary technological design — whether bi or tri-dimensional, modeled or computer-assisted — will never initiate a truly efficient relation with the real experience of our habits and actions, i.e. with all the embodied strength of our image-making consciousness: does the loss of indiciality create an introverted type of phenomenality ?

<p>The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding.</p><p>An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage.</p><p>A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner.</p><p>A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.</p><p> </p><p>The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction.</p><p> </p> / civilingenjörsexamen

This dissertation thesis deals with the use of full-time Masters' graduates of the Physical Education and Sport study program at Faculty of Physical Education and Sport at Charles University on the labor market. In the theoretical part a review of the current state of knowledge about the use of graduates on the labor market was completed, especially university graduates. On the basis of this review the construct of the use of Charles University Faculty of Physical Education and Sport graduate was operationalized and the main tool of the survey, the electronic questionnaire, was compiled. The basic set of the survey was formed by the graduates of the full-time Masters' studies program between the years 2010 and 2015 in the fields of Secondary School Teaching (double-subject), Physical Education and Sport (single-subject), Military Physical Education and Sports Management. 346 responses from 671 questionnaires were obtained (52% return rate). In the result part collected data was first analyzed by the chi-square test on the basis of 3 identification variables (gender of the respondents, field of study and year of graduation) and subsequently individual results of the survey were presented. These results were mainly related to respondents' transition to the labor market after having finished Masters'...

Cette thèse s'intéresse à la problématique du contact entre matériaux hétérogènes. L'industrie (automobile, aéronautique, spatiale, ...) s'intéresse de plus en plus à ces types de matériaux. Il s'agira par exemple des alliages métalliques, des matériaux poreux, matériaux composites (composites tissés, interlocks 3D, interlocks 2D), des billes céramiques contenant des impuretés (porosités/précipités),... Dans ce manuscrit, un modèle de contact basé sur les méthodes semi-analytiques a été développé. Un algorithme de gradient conjugué est utilisé afin de résoudre rapidement le problème de contact. Le modèle permet de prendre en compte la présence d'une ou de plusieurs hétérogénéités isotropes/anisotropes dans le problème de contact. Une approche inspirée de la méthode de l'inclusion équivalente proposée par Eshelby est utilisée dans le solveur de contact pour prendre en compte l'effet de ces hétérogénéités. Les méthodes de transformées de Fourier rapides (FFT) permettent d'accélérer les calculs. Une méthode numérique a été mise en œuvre afin de prendre en compte l'interaction entre plusieurs hétérogénéités. Le massif peut être élastique ou viscoélastique. L'approche développée dans la thèse peut résoudre à la fois les problèmes d'indentation, de roulement/glissement ou de fretting en présence de matériaux élastiques hétérogènes, viscoélastiques homogènes ou hétérogènes. Les solutions sont données en termes de champs de pressions, de cisaillements et de contraintes. Dans le cas des matériaux viscoélastiques le code de calcul est capable de fournir le coefficient de frottement apparent ainsi que toutes les variables de contact aussi bien en régime permanent que transitoire. Le modèle a été validé par comparaison avec la méthode des éléments finis classiques en utilisant le logiciel commercial Abaqus v6.11. Le temps de calcul ainsi que l'espace mémoire nécessaire sont considérablement réduits par rapport à la méthode éléments finis. La parallélisation a été introduite dans le code de contact afin de réduire toujours plus le temps de calcul. Il s'agit d'un code robuste, rapide et facilement utilisable en Bureau d'Etudes. Une approche expérimentale originale a été mise en place afin de mesurer les champs de déplacements à l'interface des corps en contact. De bonnes corrélations essais/calculs ont été obtenues. Enfin quelques applications industrielles ont été présentées. Un couplage entre un code éléments finis structurel et le code semi-analytique de résolution de contact a été également réalisé. / The present PhD thesis deals with contact problems between heterogeneous materials. Nowadays heterogeneous materials are extensively used in several industrial domains (automotive, aeronautics, aerospace, ...). Heterogeneous materials involve porous materials, aluminum alloys, composites materials (woven composites, interlocks 3D, interlocks 2D), metallic or ceramics materials containing impurities (porosities/precipitates). In this work, a contact model based on semi-analytical method is proposed. A conjugate gradient algorithm is used for a fast resolution of contact equations. The model can account for one or more isotropic/anisotropic inhomogeneities. An approach taking inspiration from the Eshelby equivalent inclusion method is used in the contact solver to account for the effect of inhomogeneities. 2D and 3D Fast Fourier Transforms (FFT) are used to speed up the computation. A numerical method is implemented in order to take into account interactions between many heterogeneities. The semi-infinite space/ matrix can be either elastic or visco-elastic. The model developed in the present PhD thesis can solve indentation, rolling/sliding or fretting contact problems between heterogeneous elastic materials, homogeneous or heterogeneous visco-elactic materials. In the case of visco-elastic materials, the model permits to get the solution in terms of contact pressure distribution, subsurface stresses, apparent friction coefficient, both in the transient and then steady-state regimes. The model has been validated by performing a comparison with the results of a finite element model. The CPU time and memory necessary are greatly reduced in comparison with the classical finite element method. The model developed is fast, robust and extremely easy to use. An original experimental approach was proposed in order to measure the displacement fields at interface of two contacting bodies. A good agreement between experimental results and numerical simulations is obtained. Finally, the model is applied on some industrial applications. A coupling between a finite element model and the semi-analytical code allow to take into account the effects of structure on contact problem.

The goal of the project is a static provision design of Drnovice castle. This castle (today a municipal office and a restaurant) is violated by vertical cracks. There is a significant horizontal displacement vector. That’s why horizontal prestress redevelopment (using prestressed cables) was chosen. A drawing documentation is an integral part of the project.

Im Zuge der kontinuierlichen Weiterentwicklung von Verarbeitungs- und Verpackungsmaschinen werden immer höhere Anforderungen an die für den Gütertransfer eingesetzte Fördertechnik gestellt. Neben der erhöhten Förderleistung sind zudem ein schmiermittelfreier Betrieb sowie eine hundertprozentige Verfügbarkeit gefordert. Durch die zunehmende Leistungssteigerung kommt es zu hohen Beanspruchungen, die bei falscher Auslegung zu mechanischem oder thermischem Versagen der Kunststoff-Bauteile im Fördersystem führen können. Während das mechanische Versagen mit den aktuellen Dimensionierungen vermieden werden kann, gibt es bezüglich des thermischen Versagens keine hinreichend genaue Auslegungsvorschrift. Die vorliegende Arbeit befasst sich mit der thermischen Analyse von Gleitketten-Fördersystemen sowie den darin eingesetzten thermoplastischen Kunststoff-Kunststoff-Gleitpaarungen. Diesbezüglich werden die Gleitkontakte eines Gleitkettenförderers und deren Belastungen analysiert. Durch Abstraktion des Kette–Schiene-Systems wird ein semi-analytisches Berechnungsmodell zur Abschätzung der Reibtemperatur entwickelt, welches mittels experimenteller Untersuchungen auf einem Tribo-Prüfstand und an einem Fördersystem verifiziert wird. Aus den Untersuchungsergebnissen konnte ein thermisches Auslegungskriterium für Kunststoff-Kunststoff-Gleitpaarungen abgeleitet werden, welches sowohl auf Gleitketten-Förderer als auch perspektivisch auf ähnliche tribologische Systeme übertragen werden kann. / In the course of the continuous enhancements of processing and packaging machines, higher demands are set on conveying technology used for transferring goods. In addition to an increased delivery rate, a lubricant-free operation as well as a hundred percent availability are claimed. Increasing performance leads to high stresses that can result to mechanical or thermal failure of plastic components in the conveying system, if incorrectly designed. While mechanical failure can be avoided with up to date dimensioning, there is no sufficiently precise dimensioning criterion in regard to thermal failure. The present thesis is concerning with the thermal analysis of sliding chain conveyor systems as well as the thermoplastic plastic-plastic sliding pairs used therein. In this regard, the sliding contacts of a sliding chain conveyor and their loads are analyzed. By abstraction of the chain–rail system, a semi-analytical model for estimating the frictional temperature is developed, which is verified by experimental studies on a tribo test bench and a conveyor system. From the study results, a thermal dimensioning criterion for plastic plastic pairings could be derived, which can be applied to sliding chain conveyor as well as perspectivly similar tribological systems.

This dissertation thesis deals with the use of full-time Masters' graduates of the Physical Education and Sport study program at Faculty of Physical Education and Sport at Charles University on the labor market. In the theoretical part a review of the current state of knowledge about the use of graduates on the labor market was completed, especially university graduates. On the basis of this review the construct of the use of Charles University Faculty of Physical Education and Sport graduate was operationalized and the main tool of the survey, the electronic questionnaire, was compiled. The basic set of the survey was formed by the graduates of the full-time Masters' studies program between the years 2010 and 2015 in the fields of Secondary School Teaching (double-subject), Physical Education and Sport (single-subject), Military Physical Education and Sports Management. 346 responses from 671 questionnaires were obtained (52% return rate). In the result part collected data was first analyzed by the chi-square test on the basis of 3 identification variables (gender of the respondents, field of study and year of graduation) and subsequently individual results of the survey were presented. These results were mainly related to respondents' transition to the labor market after having finished Masters'...